| Age | Commit message (Collapse) | Author |
|---|
|
Add a field in lparcfg output to indicate whether the kernel is
running on a dedicated or shared memory lpar. Added fields to show
the paging space pool IDs and the CMO page size.
Submitted-by: Robert Jennings <rcj@linux.vnet.ibm.com>
Signed-off-by: Paul Mackerras <paulus@samba.org>
|
|
If the firmware page size used for collaborative memory overcommit
is 4k, but the kernel is using 64k pages, the page loaning is currently
broken as it only marks the first 4k page of each 64k page as loaned.
This fixes this to iterate through each 4k page and mark them all as
loaned/active.
Signed-off-by: Brian King <brking@linux.vnet.ibm.com>
Signed-off-by: Robert Jennings <rcj@linux.vnet.ibm.com>
Signed-off-by: Paul Mackerras <paulus@samba.org>
|
|
During platform setup, save off the primary/secondary paging space
pool IDs and the page size. Added accessors in hvcall.h for these
variables. This is needed for a subsequent fix.
Submitted-by: Robert Jennings <rcj@linux.vnet.ibm.com>
Signed-off-by: Paul Mackerras <paulus@samba.org>
|
|
A small bogon sneaked into the ppc64 lockdep support. A test is
branching slightly off causing a clobbered register value to
overwrite the irq state under some circumstances.
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Signed-off-by: Paul Mackerras <paulus@samba.org>
|
|
The intent of "flush_tlbs" is to invalidate all TLB entries by doing a
TLB invalidate instruction for all pages in the address range 0 to
0x00400000. A loop counter is set up at the high value and
decremented by page size. However, the loop is only done once as the
sense of the conditional branch at the loop end does not match the
setup/decrement. This fixes it to do the whole range by correcting
the branch condition.
Signed-off-by: Rocky Craig <rocky.craig@hp.com>
Signed-off-by: Paul Mackerras <paulus@samba.org>
|
|
When we fork, init_new_context() improperly resets the vdso_base
of the new context to 0. That means that the new process loses
access to the vdso for signal trampolines.
The initialization should be unnecessary anyway as the context
on a fresh mm should be 0 in the first place and binfmt_elf
will initialize that value for a newly loaded process.
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Signed-off-by: Paul Mackerras <paulus@samba.org>
|
|
The condition is harmless and no need to scare the user
http://bugzilla.kernel.org/show_bug.cgi?id=11245
Signed-off-by: Andi Kleen <ak@linux.intel.com>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/drzeus/mmc
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/drzeus/mmc:
sdricoh_cs: removed unused #include <version.h>
s3cmci: attach get_cd host ops
s3cmci: fix sparse errors from non-exported functions
|
|
The drivers below do not use LINUX_VERSION_CODE nor KERNEL_VERSION.
drivers/mmc/host/sdricoh_cs.c
This patch removes the said #include <version.h>.
Signed-off-by: Huang Weiyi <weiyi.huang@gmail.com>
Signed-off-by: Pierre Ossman <drzeus@drzeus.cx>
|
|
Attach the routine to get_cd to allow the MMC core to find out whether
there is a card present or not without the tedious process of trying to
send commands to the card or not.
Signed-off-by: Ben Dooks <ben-linux@fluff.org>
Signed-off-by: Pierre Ossman <drzeus@drzeus.cx>
|
|
Fix the following sparse errors by making the functions
static and fixing the check for host->base.
598:6: warning: symbol 's3cmci_dma_done_callback' was not declared. Should it be static?
744:6: warning: symbol 's3cmci_dma_setup' was not declared. Should it be static?
1209:20: warning: Using plain integer as NULL pointer
Signed-off-by: Ben Dooks <ben-linux@fluff.org>
Signed-off-by: Pierre Ossman <drzeus@drzeus.cx>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/tiwai/sound-2.6
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tiwai/sound-2.6:
ALSA: hda - Fix capture source widgets on ALC codecs
|
|
security.h: fix build failure
include/linux/security.h: In function 'security_ptrace_traceme':
include/linux/security.h:1760: error: 'parent' undeclared (first use in this function)
Signed-off-by: Alexander Beregalov <a.beregalov@gmail.com>
Tested-by: Ingo Molnar <mingo@elte.hu>
Signed-off-by: James Morris <jmorris@namei.org>
|
|
On some Realtek codecs like ALC882 or ALC883, the capture source is
no mux but sum widget. We have to initialize all channels properly
for this type, otherwise noises may come in from the unused route.
The patch assures to mute unused routes, and unmute the currently
selected route.
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Tested-by: Daniel J Blueman <daniel.blueman@gmail.com>
|
|
The drivers below do not use LINUX_VERSION_CODE nor KERNEL_VERSION.
drivers/char/pcmcia/ipwireless/tty.c
drivers/char/synclink_gt.c
drivers/char/xilinx_hwicap/xilinx_hwicap.c
This patch removes the said #include <version.h>.
Signed-off-by: Huang Weiyi <weiyi.huang@gmail.com>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/tip/linux-2.6-tip
* 'core-fixes-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/linux-2.6-tip:
lockdep: fix build if CONFIG_PROVE_LOCKING not defined
lockdep: use WARN() in kernel/lockdep.c
lockdep: spin_lock_nest_lock(), checkpatch fixes
lockdep: build fix
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/tip/linux-2.6-tip
* 'sched-fixes-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/linux-2.6-tip:
sched: scale sysctl_sched_shares_ratelimit with nr_cpus
sched: fix rt-bandwidth hotplug race
sched: fix the race between walk_tg_tree and sched_create_group
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/tip/linux-2.6-tip
* 'x86-fixes-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/linux-2.6-tip: (32 commits)
x86: add MAP_STACK mmap flag
x86: fix section mismatch warning - spp_getpage()
x86: change init_gdt to update the gdt via write_gdt, rather than a direct write.
x86-64: fix overlap of modules and fixmap areas
x86, geode-mfgpt: check IRQ before using MFGPT as clocksource
x86, acpi: cleanup, temp_stack is used only when CONFIG_SMP is set
x86: fix spin_is_contended()
x86, nmi: clean UP NMI watchdog failure message
x86, NMI: fix watchdog failure message
x86: fix /proc/meminfo DirectMap
x86: fix readb() et al compile error with gcc-3.2.3
arch/x86/Kconfig: clean up, experimental adjustement
x86: invalidate caches before going into suspend
x86, perfctr: don't use CCCR_OVF_PMI1 on Pentium 4Ds
x86, AMD IOMMU: initialize dma_ops after sysfs registration
x86m AMD IOMMU: cleanup: replace LOW_U32 macro with generic lower_32_bits
x86, AMD IOMMU: initialize device table properly
x86, AMD IOMMU: use status bit instead of memory write-back for completion wait
x86: silence mmconfig printk
x86, msr: fix NULL pointer deref due to msr_open on nonexistent CPUs
...
|
|
I noticed that sysctl_check.o was the largest object file in
a allnoconfig build in kernel/*.
36243 0 0 36243 8d93 kernel/sysctl_check.o
This is because it was default y and && EMBEDDED. But I don't
really see a need for a non kernel developer to have their
sysctls checked all the time.
So move the Kconfig into the kernel debugging section and
also drop the default y and the EMBEDDED check.
Signed-off-by: Andi Kleen <ak@linux.intel.com>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
|
|
* master.kernel.org:/home/rmk/linux-2.6-arm: (38 commits)
[ARM] 5191/1: ARM: remove CVS keywords
[ARM] pxafb: fix the warning of incorrect lccr when lcd_conn is specified
[ARM] pxafb: add flag to specify output format on LDD pins when base is RGBT16
[ARM] pxafb: fix the incorrect configuration of GPIO77 as ACBIAS for TFT LCD
[ARM] 5198/1: PalmTX: PCMCIA fixes
[ARM] Fix a pile of broken watchdog drivers
[ARM] update mach-types
[ARM] 5196/1: fix inline asm constraints for preload
[ARM] 5194/1: update .gitignore
[ARM] add proc-macros.S include to proc-arm940 and proc-arm946
[ARM] 5192/1: ARM TLB: add v7wbi_{possible,always}_flags to {possible,always}_tlb_flags
[ARM] 5193/1: Wire up missing syscalls
[ARM] traps: don't call undef hook functions with spinlock held
[ARM] 5183/2: Provide Poodle LoCoMo GPIO names
[ARM] dma-mapping: provide sync_range APIs
[ARM] dma-mapping: improve type-safeness of DMA translations
[ARM] Kirkwood: instantiate the orion_spi driver in the platform code
[ARM] prevent crashing when too much RAM installed
[ARM] Kirkwood: Instantiate mv_xor driver
[ARM] Orion: Instantiate mv_xor driver for 5182
...
|
|
The exported copy of videodev2.h contains this line:
#define #include <sys/time.h>
This is because for some reason it defines __user for itself -- despite
the fact that we remove all instances of __user when exporting headers.
_All_ pointers in userspace are user pointers. Fix it by removing the
unnecessary '#define __user' from the file.
The new headers ivtv.h and ivtvfb.h would have the same problem... if
whoever put them there had actually remembered to add them to the Kbuild
file while he was at it. Fix those too, and export them as was
presumably intended.
Note that includes of <linux/compiler.h> are also stripped by the header
export process, so those don't need to be conditional.
Signed-off-by: David Woodhouse <David.Woodhouse@intel.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
Acked-by: Hans Verkuil <hverkuil@xs4all.nl>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
|
|
Try to comment away a little of the confusion between mm's vm_area_struct
vm_flags and vmalloc's vm_struct flags: based on an idea by Ulrich Drepper.
Signed-off-by: Hugh Dickins <hugh@veritas.com>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
|
|
This patch removes CVS keywords that weren't updated for a long time.
Signed-off-by: Adrian Bunk <bunk@kernel.org>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
|
|
Bump driver version to 1.0.2.
Signed-off-by: Brian King <brking@linux.vnet.ibm.com>
Signed-off-by: James Bottomley <James.Bottomley@HansenPartnership.com>
|
|
When logging async events, also print the payload in addition to the
event received.
Signed-off-by: Brian King <brking@linux.vnet.ibm.com>
Signed-off-by: James Bottomley <James.Bottomley@HansenPartnership.com>
|
|
Sanitize the response lengths in order to prevent possible oopses
in the command response path.
Signed-off-by: Brian King <brking@linux.vnet.ibm.com>
Signed-off-by: James Bottomley <James.Bottomley@HansenPartnership.com>
|
|
If the client virtual fibre channel adapter is already logged into the
server and does an NPIV Login again, the async queue, which is used for
reporting Link Up/Link Down type of events, does not get reset on the
server side. Fix up the client driver so that we also do not reset it.
This fixes a problem of lost async events following relogins.
Signed-off-by: Brian King <brking@linux.vnet.ibm.com>
Signed-off-by: James Bottomley <James.Bottomley@HansenPartnership.com>
|
|
If an ELS is received while the virtual fibre channel adapter is going
through its discovery, a flag is set which causes discovery to get
re-driven. However, the hosts's state does not get set back to
IBMVFC_INITIALIZING and scsi_block_requests does not get called again,
which can result in queuecommand ops getting sent during
discovery. This should not occur and may cause problems. One example
is that we may no longer be logged into the target we send the command
to, resulting in a failure which should not have occurred.
Signed-off-by: Brian King <brking@linux.vnet.ibm.com>
Signed-off-by: James Bottomley <James.Bottomley@HansenPartnership.com>
|
|
This fixes a hang on module removal. The module removal code was setting
the hosts's state to IBMVFC_HOST_OFFLINE before tearing down the kernel
thread, but, due to a bug in ibmvfc_wait_while_resetting, was not waiting
for the kernel thread's offlining work to be done prior to destroying
the kernel thread, which left the scsi host in a blocked state which we
never got out of.
Signed-off-by: Brian King <brking@linux.vnet.ibm.com>
Signed-off-by: James Bottomley <James.Bottomley@HansenPartnership.com>
|
|
The newly introduced "lcd_conn" field for connected LCD panel type will
cause the original code to generate the warnings of incorrect lccr*.
This is unnecessary since well encoded LCD_* flags will not generate
incorrect combinition of lccr* bits. Skip the check if "lcd_conn" is
specified.
Signed-off-by: Eric Miao <eric.miao@marvell.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
|
|
Another fix of inconsistent shift of the LCD_BIAS_ACTIVE_* and
LCD_PCLK_EDGE_* is also included.
Signed-off-by: Eric Miao <eric.miao@marvell.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
|
|
Signed-off-by: Eric Miao <eric.miao@marvell.com>
Tested-by: Robert Jarzmik <robert.jarzmik@free.fr>
Tested-by: Alex Osborne <ato@meshy.org>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
|
|
Fix GPIO handling in the PCMCIA driver.
Signed-off-by: Marek Vasut <marek.vasut@gmail.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
|
|
When running ibmvscsi in a shared memory partition, it must provide
a default value for the amount of DMA resources it will need in order to
perform reasonably well. This was being calculated in sectors rather than
bytes, as it should. This patch fixes this.
Signed-off-by: Brian King <brking@linux.vnet.ibm.com>
Signed-off-by: James Bottomley <James.Bottomley@HansenPartnership.com>
|
|
/sys/bus/pci/drivers/megaraid_sas/dbg_lvl defaults to being
world-writable, which seems bad (letting any user affect kernel driver
behavior and logging level).
This turns off group and user write permissions, so that on typical
production systems only root can write to it.
[jejb: fix up rejections]
Signed-off-by: Joseph Malicki <jmalicki@metacarta.com>
Acked-by: "Yang, Bo" <Bo.Yang@lsi.com>
Signed-off-by: James Bottomley <James.Bottomley@HansenPartnership.com>
|
|
Signed-off-by: Andrew Vasquez <andrew.vasquez@qlogic.com>
Signed-off-by: James Bottomley <James.Bottomley@HansenPartnership.com>
|
|
During internal testing, we've seen issues (hangs) with the
'deferred' vport tear-down-processing typically accompanied with
the fc_remove_host() call. This is due to the current
implementation's back-end vport handling being performed by the
physical-HA's DPC thread where premature shutdown could lead to
latent vport requests without a processor.
This should also address a problem reported by Gal Rosen
(http://marc.info/?l=linux-scsi&m=121731664417358&w=2) where the
driver would attempt to awaken a previously torn-down DPC thread
from interrupt context by implicitly calling wake_up_process()
rather than the driver's qla2xxx_wake_dpc() helper. Rather, than
reshuffle the remove_one() device-removal code, during unload,
depend on the driver's timer to wake-up the DPC process, by
limiting wake-ups based on an 'unloading' flag.
Signed-off-by: Andrew Vasquez <andrew.vasquez@qlogic.com>
Signed-off-by: James Bottomley <James.Bottomley@HansenPartnership.com>
|
|
The executing-HA of an SRB can be referenced from the sp->fcport.
Use this correct value while processing status-continuation data
and abort processing.
Signed-off-by: Andrew Vasquez <andrew.vasquez@qlogic.com>
Signed-off-by: James Bottomley <James.Bottomley@HansenPartnership.com>
|
|
Signed-off-by: Andrew Vasquez <andrew.vasquez@qlogic.com>
Signed-off-by: James Bottomley <James.Bottomley@HansenPartnership.com>
|
|
Original code inadvertently cleared an SRB's 'flags' while
aborting; causing a follow-on scsi_dma_unmap() to be potentially
missed.
Signed-off-by: Andrew Vasquez <andrew.vasquez@qlogic.com>
Signed-off-by: James Bottomley <James.Bottomley@HansenPartnership.com>
|
|
* Use correct 'ha' to mark a device lost from ISR.
I/Os will always be returned on the physical-HA.
qla2x00_mark_device_lost() should be called with the HA bound
to the fcport.
* Mark *all* devices lost during ISP-ABORT (bighammer).
These fixes correct issues discovered locally where during
link-perturbation and heavy vport-I/O fcport/rport states would
stray and an rport's scsi-target lost (timed-out).
Signed-off-by: Andrew Vasquez <andrew.vasquez@qlogic.com>
Signed-off-by: James Bottomley <James.Bottomley@HansenPartnership.com>
|
|
Greg Wettstein (greg@enjellic.com) noted:
http://article.gmane.org/gmane.linux.scsi/43409
on a reboot of a previously recognized SCST target, the initiator
driver would be unable to re-recognize the device as a target.
It turns out that prior to the SCST software reloading and
returning it's "target-capable" abilities in the PRLI payload,
the HBA would be re-initialized as an initiator-only type port.
Since initiators typically classify themselves as an FCP-2
capable device, both software and firmware do not perform an
explicit logout during port-loss. Unfortunately, as can be seen
by the failure case, when the port (now target-capable) returns,
firmware performs an ADISC without a follow-on PRLI, leaving
stale 'initiator-only' data in the firmware's port database.
Correct the discrepancy by performing the explicit logout during
the transport's request to terminate-rport-io, thus synchronizing
port states and ensuring a follow-on PRLI is performed.
Reported-by: Greg Wettstein <greg@enjellic.com>
Signed-off-by: Andrew Vasquez <andrew.vasquez@qlogic.com>
Cc: Stable Tree <stable@kernel.org>
Signed-off-by: James Bottomley <James.Bottomley@HansenPartnership.com>
|
|
lun_state need to be initialized inside check_ownership().
Signed-off-by: Chandra Seetharaman <sekharan@us.ibm.com>
Signed-off-by: James Bottomley <James.Bottomley@HansenPartnership.com>
|
|
RDAC storage controller doesn't seem to use the scsilun format. It uses
only the last byte for LUN.
Signed-off-by: Chandra Seetharaman <sekharan@us.ibm.com>
Signed-off-by: James Bottomley <James.Bottomley@HansenPartnership.com>
|
|
Signed-off-by: Bo Yang <bo.yang@lsi.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: James Bottomley <James.Bottomley@HansenPartnership.com>
|
|
Add the new controllers (0x78 0x79) support to the driver. Those
controllers are LSI's next generation (gen2) SAS controllers.
[akpm@linux-foundation.org: coding-style fixes]
[akpm@linux-foundation.org: parenthesise a macro]
Signed-off-by: Bo Yang <bo.yang@lsi.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: James Bottomley <James.Bottomley@HansenPartnership.com>
|
|
Add the shutdown DCMD cmd to driver shutdown routine to make megaraid sas
FW shutdown proper.
Signed-off-by: Bo Yang <bo.yang@lsi.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: James Bottomley <James.Bottomley@HansenPartnership.com>
|
|
MegaRAID SAS Driver get unexpected Interrupt. Add the dummy readl to
force PCI flush will fix this issue.
Signed-off-by: Bo Yang <bo.yang@lsi.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Cc: Stable Tree <stable@kernel.org>
Signed-off-by: James Bottomley <James.Bottomley@HansenPartnership.com>
|
|
These patches from Adrian fix:
- ixp4xx_wdt: 20d35f3e50ea7e573f9568b9fce4e98523aaee5d
CC drivers/watchdog/ixp4xx_wdt.o
ixp4xx_wdt.c:32: error: expected '=', ',', ';', 'asm' or '__attribute__'
ixp4xx_wdt.c: In function 'wdt_enable':
ixp4xx_wdt.c:41: error: 'wdt_lock' undeclared (first use in this
ixp4xx_wdt.c:41: error: (Each undeclared identifier is reported only
ixp4xx_wdt.c:41: error: for each function it appears in.)
ixp4xx_wdt.c: In function 'wdt_disable':
ixp4xx_wdt.c:52: error: 'wdt_lock' undeclared (first use in this
ixp4xx_wdt.c: In function 'ixp4xx_wdt_init':
ixp4xx_wdt.c:186: error: 'wdt_lock' undeclared (first use in this
make[3]: *** [drivers/watchdog/ixp4xx_wdt.o] Error 1
- at91rm9200_wdt: 2760600da2a13d5a2a335ba012d0f3ad5df4c098
CC drivers/watchdog/at91rm9200_wdt.o
at91rm9200_wdt.c:188: error: 'at91_wdt_ioctl' undeclared here (not in a
make[3]: *** [drivers/watchdog/at91rm9200_wdt.o] Error 1
- wdt285: d0e58eed05f9baf77c4f75e794ae245f6dae240a
CC [M] drivers/watchdog/wdt285.o
wdt285.c: In function 'footbridge_watchdog_init':
wdt285.c:211: error: 'KERN_WARN' undeclared (first use in this function)
wdt285.c:211: error: (Each undeclared identifier is reported only once
wdt285.c:211: error: for each function it appears in.)
wdt285.c:212: error: expected ')' before string constant
make[3]: *** [drivers/watchdog/wdt285.o] Error 1
And this patch from rmk:
- s3c2410_wdt: 41dc8b72e37c514f7332cbc3f3dd864910c2a1fa
CC drivers/watchdog/s3c2410_wdt.o
s3c2410_wdt.c: In function `s3c2410wdt_start':
s3c2410_wdt.c:161: warning: `return' with a value, in function returning void
Reported-by: Adrian Bunk <bunk@kernel.org>
Signed-off-by: Adrian Bunk <bunk@kernel.org>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
|
|
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
|
