| Age | Commit message (Collapse) | Author |
|---|
|
This converts the mcp23s08 driver to be able to be used with
device tree.
There is a "spi-present-mask" device tree property, that allows to
use multiple of this spi chips on the same chipselect.
v4:
- removed the ability to specify the pullup from device tree
- updated binding doc
v3:
- removed mcp,chips device tree property in favour of a
mcp,spi-present-mask and a flag for the pullup of every gpio
- seperated the match table. Now there is one for i2c and one for spi
- do the of reading stuff on stack of the probe function - no devm
any more
v2:
- squashed booth patches together
- fixed build warning, when CONFIG_OF is not defined
- use of_match_ptr macro for of_match_table
Signed-off-by: Lars Poeschel <poeschel@lemonage.de>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
|
|
When booting with device-tree the function pointer for detecting context
loss is not populated. Ideally, the pm_runtime framework should be
enhanced to allow a means for reporting context/state loss and we could
avoid populating such function pointers altogether. In the interim until
a generic non-device specific solution is in place, force a restore of
the gpio bank when enabling the gpio controller.
Adds a new device-tree property for the OMAP GPIO controller to indicate
if the GPIO controller is located in a power-domain that never loses
power and hence will always maintain its logic state.
Signed-off-by: Jon Hunter <jon-hunter@ti.com>
Acked-by: Santosh Shilimkar <santosh.shilimkar@ti.com>
Reviewed-by: Kevin Hilman <khilman@linaro.org>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
|
|
The OMAP GPIO interrupt service routine is checking each bit in the
GPIO interrupt status register to see which bits are set. It is not
efficient to check every bit especially if only a few bits are set.
Therefore, instead of checking every bit use the __ffs() function,
which returns the location of the first set bit, to find all the set
bits.
This optimisation was suggested-by and developed in collaboration
with Felipe Balbi.
Signed-off-by: Jon Hunter <jon-hunter@ti.com>
Reviewed-by: Felipe Balbi <balbi@ti.com>
Acked-by: Santosh Shilimkar <santosh.shilimkar@ti.com>
Reviewed-by: Kevin Hilman <khilman@linaro.org>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
|
|
68942edb09f69b6e09522d1d346665eb3aadde49 (gpio/omap: fix wakeups
on level-triggered GPIOs) already restores the fallingdetect and
risingdetect contexts in *_runtime_resume(). These registers were
modified in *_runtime_suspend() to include even those configured
as level-triggered since only edge-triggered gpios can generate
wakeup events. Therefore, the old context restores of the same
registers present later in the code is not needed any more.
Remove them.
Signed-off-by: Tarun Kanti DebBarma <tarun.kanti@ti.com>
Signed-off-by: Jon Hunter <jon-hunter@ti.com>
Acked-by: Santosh Shilimkar <santosh.shilimkar@ti.com>
Reviewed-by: Kevin Hilman <khilman@linaro.org>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
|
|
Currently the IRQ domain is not freed once allocated, in the case where
omap_gpio_probe() fails. Therefore, ensure we free the domain if the
probe does fail. Furthermore, the local variable "ret" is not needed
and so remove this.
Signed-off-by: Jon Hunter <jon-hunter@ti.com>
Acked-by: Santosh Shilimkar <santosh.shilimkar@ti.com>
Reviewed-by: Kevin Hilman <khilman@linaro.org>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
|
|
There is no general support for 64-bit big endian accesses, so that is
left unsupported.
Signed-off-by: Andreas Larsson <andreas@gaisler.com>
Acked-by: Anton Vorontsov <anton@enomsg.org>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
|
|
The of_device_id table is supposed to be zero-terminated.
Signed-off-by: Axel Lin <axel.lin@ingics.com>
Acked-by: Grant Likely <grant.likely@secretlab.ca>
Acked-by: Kukjin Kim <kgene.kim@samsung.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
|
|
This patch adds a dedicated dbg_show function to the gpio-mvebu driver.
In addition to the generic gpiolib informations, this function displays
informations related with the specific Marvell registers (blink enable,
data in polarity, interrupt masks and cause).
Signed-off-by: Simon Guinot <simon.guinot@sequanux.org>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
|
|
The bit_per_word can be set in the OF Device tree, so no need to force it as with
the platform_data when using OF Platform
Signed-off-by: Patrick Vasseur <patrick.vasseur@c-s.fr>
Signed-off-by: Christophe Leroy <christophe.leroy@c-s.fr>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
|
|
Fix :
gpio/gpio-tps65910.c:136: ERROR: space required before the open parenthesis '('
Signed-off-by: Laurent Navet <laurent.navet@gmail.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
|
|
Fix :
gpio/gpio-timberdale.c:171: ERROR: else should follow close brace '}'
Signed-off-by: Laurent Navet <laurent.navet@gmail.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
|
|
Fix :
gpio/gpio-tc3589x.c:285: ERROR: code indent should use tabs where possible
gpio/gpio-tc3589x.c:286: ERROR: code indent should use tabs where possible
gpio/gpio-tc3589x.c:287: ERROR: code indent should use tabs where possible
gpio/gpio-tc3589x.c:347: ERROR: code indent should use tabs where possible
Signed-off-by: Laurent Navet <laurent.navet@gmail.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
|
|
Fix :
gpio/gpio-stp-xway.c:220: ERROR: trailing whitespace
Signed-off-by: Laurent Navet <laurent.navet@gmail.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
|
|
Fix :
gpio/gpio-sch.c:206: ERROR: switch and case should be at the same indent
Also remove blank lines
Signed-off-by: Laurent Navet <laurent.navet@gmail.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
|
|
Fix :
gpio/gpio-pxa.c:605: ERROR: space required after that ',' (ctx:VxV)
gpio/gpio-pxa.c:672: ERROR: space prohibited after that open parenthesis '('
Signed-off-by: Laurent Navet <laurent.navet@gmail.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
|
|
Fix :
gpio/gpio-pca953x.c:150: ERROR: else should follow close brace '}'
Signed-off-by: Laurent Navet <laurent.navet@gmail.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
|
|
Fix :
gpio/gpio-omap.c:697: ERROR: space required before the open parenthesis '('
Signed-off-by: Laurent Navet <laurent.navet@gmail.com>
Acked-by: Santosh Shilimkar <santosh.shilimkar@ti.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
|
|
Fix :
gpio/gpio-mvebu.c:120: ERROR: space required before the open parenthesis '('
gpio/gpio-mvebu.c:136: ERROR: space required before the open parenthesis '('
gpio/gpio-mvebu.c:154: ERROR: space required before the open parenthesis '('
gpio/gpio-mvebu.c:404: ERROR: space required before the open parenthesis '('
gpio/gpio-mvebu.c:476: ERROR: "(foo*)" should be "(foo *)"
gpio/gpio-mvebu.c:480: ERROR: "(foo*)" should be "(foo *)"
gpio/gpio-mvebu.c:484: ERROR: "(foo*)" should be "(foo *)"
gpio/gpio-mvebu.c:512: ERROR: space prohibited after that '!' (ctx:BxW)
gpio/gpio-mvebu.c:518: ERROR: space prohibited after that '!' (ctx:BxW)
gpio/gpio-mvebu.c:518: ERROR: space required before the open brace '{'
gpio/gpio-mvebu.c:563: ERROR: space prohibited after that '!' (ctx:BxW)
gpio/gpio-mvebu.c:570: ERROR: trailing whitespace
gpio/gpio-mvebu.c:577: ERROR: space required before the open parenthesis '('
gpio/gpio-mvebu.c:635: ERROR: space prohibited after that '!' (ctx:BxW)
Signed-off-by: Laurent Navet <laurent.navet@gmail.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
|
|
Fix :
gpio/gpiolib-of.c:64: ERROR: code indent should use tabs where possible
Signed-off-by: Laurent Navet <laurent.navet@gmail.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
|
|
Use the wrapper functions for getting and setting the driver data
using spi_device instead of using dev_{get|set}_drvdata with
&spi->dev, so we can directly pass a struct spi_device.
Signed-off-by: Jingoo Han <jg1.han@samsung.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
|
|
Use the wrapper functions for getting and setting the driver data
using spi_device instead of using dev_{get|set}_drvdata with
&spi->dev, so we can directly pass a struct spi_device.
Signed-off-by: Jingoo Han <jg1.han@samsung.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
|
|
dev_err() is more preferred than printk().
Signed-off-by: Jingoo Han <jg1.han@samsung.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
|
|
Use devm_kzalloc() to make cleanup paths simpler.
Signed-off-by: Jingoo Han <jg1.han@samsung.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
|
|
Use devm_kzalloc() to make cleanup paths simpler.
Signed-off-by: Jingoo Han <jg1.han@samsung.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
|
|
Use devm_kzalloc() to make cleanup paths simpler.
Signed-off-by: Jingoo Han <jg1.han@samsung.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
|
|
Use devm_kzalloc() to make cleanup paths simpler.
Signed-off-by: Jingoo Han <jg1.han@samsung.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
|
|
Use devm_kzalloc() to make cleanup paths simpler.
Signed-off-by: Jingoo Han <jg1.han@samsung.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
|
|
Use devm_kzalloc() to make cleanup paths simpler.
Signed-off-by: Jingoo Han <jg1.han@samsung.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
|
|
Use the newly introduced devm_ioremap_resource() instead of
devm_request_and_ioremap() which provides more consistent error handling.
devm_ioremap_resource() provides its own error messages; so all explicit
error messages can be removed from the failure code paths.
Signed-off-by: Sachin Kamat <sachin.kamat@linaro.org>
Reviewed-by: Thierry Reding <thierry.reding@avionic-design.de>
Acked-by: Tony Prisk <linux@prisktech.co.nz>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
|
|
Update the Emma Mobile GPIO driver to make use of devm
functions. This simplifies the error handling and makes
the code more compact.
Signed-off-by: Magnus Damm <damm@opensource.se>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
|
|
Lynxpoint gpio driver uses X86 specific io-ports to control gpios
Signed-off-by: Mathias Nyman <mathias.nyman@linux.intel.com>
Reviewed-by: Mika Westerberg <mika.westerberg@linux.intel.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
|
|
It is more readable for humans to use double-bang (!!) to convert the value
to pure boolean before it is returned.
Signed-off-by: Mika Westerberg <mika.westerberg@linux.intel.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
|
|
The E6xx (TunnelCreek) CPUs have 9 GPIO lines in the resume well. Update
the resume functions to allow for more than 8 GPIO lines, using the core
functions as a template.
Cc: Grant Likely <grant.likely@secretlab.ca>
Cc: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Darren Hart <dvhart@linux.intel.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
|
|
Signed-off-by: Nikolay Balandin <nbalandin@dev.rtsoft.ru>
Acked-by: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
|
|
Set it once is enough, and it's done in vprbrd_gpiob_set() which is called by
vprbrd_gpiob_direction_output().
Signed-off-by: Axel Lin <axel.lin@ingics.com>
Tested-by: Lars Poeschel <poeschel@lemonage.de>
Acked-by: Lars Poeschel <poeschel@lemonage.de>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
|
|
Stop checking for pin availability in direction and get functions.
These functions can be called repeatedly, so checking every time is
bad for performance. Now that requesting GPIO pins is no longer
optional, checking for availability at pin request time is enough.
Signed-off-by: Jean Delvare <khali@linux-fr.org>
Cc: Peter Tyser <ptyser@xes-inc.com>
Cc: Grant Likely <grant.likely@secretlab.ca>
Cc: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
|
|
Update the Emma Mobile GPIO driver to add DT support.
The patch simply adds a two-cell xlate function and
updates the probe code to allow configuration via DT
using the "ngpios" property plus OF id in the same
style as gpio-mvebu.c. The code is also adjusted to
use postcore_initcall() to force early setup.
Signed-off-by: Magnus Damm <damm@opensource.se>
Signed-off-by: Grant Likely <grant.likely@secretlab.ca>
|
|
For OMAP devices, if a gpio is being used as an interrupt source but has
not been requested by calling gpio_request(), a call to request_irq()
may cause the kernel hang because the gpio bank may be disabled and
hence the register access will fail. To prevent such hangs, test for
this case and warn if this is detected.
Signed-off-by: Jon Hunter <jon-hunter@ti.com>
Reviewed-by: Felipe Balbi <balbi@ti.com>
Acked-by: Santosh Shilimkar <santosh.shilimkar@ti.com>
Acked-by: Kevin Hilman <khilman@linaro.org>
Tested-by: Javier Martinez Canillas <javier@dowhile0.org>
Signed-off-by: Grant Likely <grant.likely@secretlab.ca>
|
|
Currently the OMAP GPIO driver uses a legacy mapping for the GPIO IRQ
domain. This is not necessary because we do not need to assign a
specific interrupt number to the GPIO IRQ domain. Therefore, convert
the OMAP GPIO driver to use a linear mapping instead.
Please note that this also allows to simplify the logic in the OMAP
gpio_irq_handler() routine, by using irq_find_mapping() to obtain the
virtual irq number from the GPIO bank and bank index.
Reported-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Jon Hunter <jon-hunter@ti.com>
Reviewed-by: Felipe Balbi <balbi@ti.com>
Acked-by: Santosh Shilimkar <santosh.shilimkar@ti.com>
Acked-by: Kevin Hilman <khilman@linaro.org>
Tested-by: Javier Martinez Canillas <javier@dowhile0.org>
Signed-off-by: Grant Likely <grant.likely@secretlab.ca>
|
|
Tegra only supports, and always enables, device tree. Remove all ifdefs
and runtime checks for DT support from the driver.
Signed-off-by: Stephen Warren <swarren@nvidia.com>
Signed-off-by: Grant Likely <grant.likely@secretlab.ca>
|
|
ichx_gpio_check_available() returns either 0 or -ENXIO depending on whether
the given GPIO is available or not. However, callers of this function treat
the return value as boolean:
...
if (!ichx_gpio_check_available(gpio, nr))
return -ENXIO;
which erroneusly fails when the GPIO is available and not vice versa.
Fix this by making the function return boolean as expected by the callers.
Signed-off-by: Mika Westerberg <mika.westerberg@linux.intel.com>
Signed-off-by: Grant Likely <grant.likely@secretlab.ca>
|
|
This comment applies to gpio_to_chip(), not gpiod_to_chip().
Signed-off-by: Alexandre Courbot <acourbot@nvidia.com>
Signed-off-by: Grant Likely <grant.likely@secretlab.ca>
|
|
Constify descriptor parameter of gpiod_* functions for those that
should obviously not modify it. This includes value or direction get,
cansleep, and IRQ number query.
Signed-off-by: Alexandre Courbot <acourbot@nvidia.com>
Signed-off-by: Grant Likely <grant.likely@secretlab.ca>
|
|
Some functions dereferenced their GPIO descriptor argument without
checking its validity first, potentially leading to an oops when given
an invalid argument.
This patch also makes gpio_get_value() more resilient when given an
invalid GPIO, returning 0 instead of silently crashing.
Signed-off-by: Alexandre Courbot <acourbot@nvidia.com>
Cc: Ryan Mallon <rmallon@gmail.com>
Signed-off-by: Grant Likely <grant.likely@secretlab.ca>
|
|
git://github.com/markus-oberhumer/linux
Pull LZO compression update from Markus Oberhumer:
"Summary:
========
Update the Linux kernel LZO compression and decompression code to the
current upstream version which features significant performance
improvements on modern machines.
Some *synthetic* benchmarks:
============================
x86_64 (Sandy Bridge), gcc-4.6 -O3, Silesia test corpus, 256 kB block-size:
compression speed decompression speed
LZO-2005 : 150 MB/sec 468 MB/sec
LZO-2012 : 434 MB/sec 1210 MB/sec
i386 (Sandy Bridge), gcc-4.6 -O3, Silesia test corpus, 256 kB block-size:
compression speed decompression speed
LZO-2005 : 143 MB/sec 409 MB/sec
LZO-2012 : 372 MB/sec 1121 MB/sec
armv7 (Cortex-A9), Linaro gcc-4.6 -O3, Silesia test corpus, 256 kB block-size:
compression speed decompression speed
LZO-2005 : 27 MB/sec 84 MB/sec
LZO-2012 : 44 MB/sec 117 MB/sec
**LZO-2013-UA : 47 MB/sec 167 MB/sec
Legend:
LZO-2005 : LZO version in current 3.8 kernel (which is based on
the LZO 2.02 release from 2005)
LZO-2012 : updated LZO version available in linux-next
**LZO-2013-UA : updated LZO version available in linux-next plus experimental
ARM Unaligned Access patch. This needs approval
from some ARM maintainer ist NOT YET INCLUDED."
Andrew Morton <akpm@linux-foundation.org> acks it and says:
"There's a new LZ4 on the block which is even faster than the sped-up
LZO, but various filesystems and things use LZO"
* tag 'lzo-update-signature-20130226' of git://github.com/markus-oberhumer/linux:
crypto: testmgr - update LZO compression test vectors
lib/lzo: Update LZO compression to current upstream version
lib/lzo: Rename lzo1x_decompress.c to lzo1x_decompress_safe.c
|
|
Pull one kvm bugfix from Gleb Natapov.
* git://git.kernel.org/pub/scm/virt/kvm/kvm:
x86/kvm: Fix pvclock vsyscall fixmap
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/mchehab/linux-edac
Pull EDAC fixes and ghes-edac from Mauro Carvalho Chehab:
"For:
- Some fixes at edac drivers (i7core_edac, sb_edac, i3200_edac);
- error injection support for i5100, when EDAC debug is enabled;
- fix edac when it is loaded builtin (early init for the subsystem);
- a "Firmware First" EDAC driver, allowing ghes to report errors via
EDAC (ghes-edac).
With regards to ghes-edac, this fixes a longstanding BZ at Red Hat
that happens with Nehalem and Sandy Bridge CPUs: when both GHES and
i7core_edac or sb_edac are running, the error reports are
unpredictable, as both BIOS and OS race to access the registers. With
ghes-edac, the EDAC core will refuse to register any other concurrent
memory error driver.
This patchset moves the ghes struct definitions to a separate header
file (include/acpi/ghes.h) and adds 3 hooks at apei/ghes.c to
register/unregister and to report errors via ghes-edac. Those changes
were acked by ghes driver maintainer (Huang)."
* 'linux_next' of git://git.kernel.org/pub/scm/linux/kernel/git/mchehab/linux-edac: (30 commits)
i5100_edac: convert to use simple_open()
ghes_edac: fix to use list_for_each_entry_safe() when delete list items
ghes_edac: Fix RAS tracing
ghes_edac: Make it compliant with UEFI spec 2.3.1
ghes_edac: Improve driver's printk messages
ghes_edac: Don't credit the same memory dimm twice
ghes_edac: do a better job of filling EDAC DIMM info
ghes_edac: add support for reporting errors via EDAC
ghes_edac: Register at EDAC core the BIOS report
ghes: add the needed hooks for EDAC error report
ghes: move structures/enum to a header file
edac: add support for error type "Info"
edac: add support for raw error reports
edac: reduce stack pressure by using a pre-allocated buffer
edac: lock module owner to avoid error report conflicts
edac: remove proc_name from mci structure
edac: add a new memory layer type
edac: initialize the core earlier
edac: better report error conditions in debug mode
i5100_edac: Remove two checkpatch warnings
...
|
|
The new intel_powerclamp thermal cooling device driver was merged in
commit 2af78448fff6 (Pull thermal management updates from Zhang Rui)
without any data conflicts. But there was a more subtle conflict I
missed: the driver uses MAX_USER_RT_PRIO, but commit 8bd75c77b7c6
("sched/rt: Move rt specific bits into new header file") had moved that
define from <linux/sched.h> to <linux/sched/rt.h>.
Which caused this build failure:
drivers/thermal/intel_powerclamp.c: In function ‘clamp_thread’:
drivers/thermal/intel_powerclamp.c:360:21: error: ‘MAX_USER_RT_PRIO’ undeclared (first use in this function)
drivers/thermal/intel_powerclamp.c:360:21: note: each undeclared identifier is reported only once for each function it appears in
And because I don't do a full "make allmodconfig" build after each pull,
I didn't notice until too late. So now the fix is here, separately from
the merge commit.
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc
Pull ARM SoC mvebu platform changes from Olof Johansson:
"This series contains changes for the Marvell EBU platforms (mvebu,
orion, kirkwood, dove) that were not part of the first set of pull
requests because of dependencies on the MMC tree, and being submitted
a little late.
Notable changes are:
- More devices get moved out of board files into device tree
descriptions. The remaining devices listed in there have patches
that will get sent for 3.10, after which we can remove a lot of the
board files entirely. We are doing the pinctrl and mmc drivers
here, ethernet and PCI still remain.
- SMP support for mvebu is improved with support for the local
interrupt controller.
- The Guruplug board file gets replaced with a DT description.
Unfortunately, the dependency on the MMC tree turned out to be a much
larger problem than expected, when the MMC maintainer rebased the
patches in his tree that all of the patches in this branch are based
on, which caused merge conflicts between the new and old versions of
those patches.
To work around the merge conflicts, this branch rebases all patches on
top of the respective MMC patches that did get merged into 3.9. The
patches are all identical to the versions that were part of
linux-next, but have a new commit date."
* tag 'late-mvebu-rebased' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc: (90 commits)
arm: mvebu: enable the SD card slot on Armada 370 Reference Design board
ARM: kirkwood: topkick: init mvsdio via DT
ARM: kirkwood: nsa310: convert to pinctrl
ARM: Kirkwood: topkick: Enable i2c bus.
ARM: kirkwood: topkick: convert to pinctrl
ARM: dove: convert serial DT nodes to clocks property
arm: mvebu: Add SPI flash on Armada 370 DB board
arm: mvebu: Add SPI flash on Armada XP-DB board
arm: mvebu: Add SPI flash on Armada XP-GP board
arm: mvebu: Add support for SPI controller in Armada 370/XP
clocksource: update and move armada-370-xp-timer documentation to timer directory
arm: mvebu: update DT to support local timers
ARM: Dove: convert usb host controller to DT
arm: mvebu: Enable USB controllers on Armada 370/XP boards
arm: mvebu: Add support for USB host controllers in Armada 370/XP
arm: mvebu: add button for OpenBlocks AX3-4
ARM: Kirkwood: Convert NS2 to gpio-poweroff.
ARM: Kirkwood: Convert NSA310 I2C to device tree
ARM: Kirkwood: Convert NSA310 to use gpio-poweroff driver
ARM: Kirkwood: Convert NSA310 to DT based regulators.
...
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc
Pull ARM SoC late OMAP changes from Olof Johansson:
"This branch contains changes for OMAP that came in late during the
release staging, close to when the merge window opened.
It contains, among other things:
- OMAP PM fixes and some patches for audio device integration
- OMAP clock fixes related to common clock conversion
- A set of patches cleaning up WFI entry and blocking.
- A set of fixes and IP block support for PM on TI AM33xx SoCs
(Beaglebone, etc)
- A set of smaller fixes and cleanups around AM33xx restart and
revision detection, as well as removal of some dead code
(CONFIG_32K_TIMER_HZ)"
* tag 'late-omap' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc: (34 commits)
ARM: omap2: include linux/errno.h in hwmod_reset
ARM: OMAP2+: fix some omap_device_build() calls that aren't compiled by default
ARM: OMAP4: hwmod data: Enable AESS hwmod device
ARM: OMAP4: hwmod data: Update AESS data with memory bank area
ARM: OMAP4+: AESS: enable internal auto-gating during initial setup
ASoC: TI AESS: add autogating-enable function, callable from architecture code
ARM: OMAP2+: hwmod: add enable_preprogram hook
ARM: OMAP4: clock data: Add missing clkdm association for dpll_usb
ARM: OMAP2+: PM: Fix the dt return condition in pm_late_init()
ARM: OMAP2: am33xx-hwmod: Fix "register offset NULL check" bug
ARM: OMAP2+: AM33xx: hwmod: add missing HWMOD_NO_IDLEST flags
ARM: OMAP: AM33xx hwmod: Add parent-child relationship for PWM subsystem
ARM: OMAP: AM33xx hwmod: Corrects PWM subsystem HWMOD entries
ARM: DTS: AM33XX: Add nodes for OCMC RAM and WKUP-M3
ARM: OMAP2+: AM33XX: Update the hardreset API
ARM: OMAP2+: AM33XX: hwmod: Update the WKUP-M3 hwmod with reset status bit
ARM: OMAP2+: AM33XX: hwmod: Fixup cpgmac0 hwmod entry
ARM: OMAP2+: AM33XX: hwmod: Update TPTC0 hwmod with the right flags
ARM: OMAP2+: AM33XX: hwmod: Register OCMC RAM hwmod
ARM: OMAP2+: AM33XX: CM/PRM: Use __ASSEMBLER__ macros in header files
...
|
