| Age | Commit message (Collapse) | Author |
|---|
|
In iwl_bg_request_scan function, if we could not send a
scan command it will go to done.
In done it does the right thing to call mac80211 with
scan complete, but the problem is STATUS_SCAN_HW is still
set causing any future scan to fail. Fix by clearing the scanning status
bits if scan fails.
Signed-off-by: Mohamed Abbas <mohamed.abbas@intel.com>
Signed-off-by: Reinette Chatre <reinette.chatre@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
|
|
Unfortunately, the result was that mac80211 didn't see all the beacons
it actually wanted to see. This caused lost associations.
Hopefully we can revisit this when mac80211 is less greedy about seeing
beacons directly...
This reverts commit 063279062a8c530cc90fb77797db16c49c905b26.
Signed-off-by: John W. Linville <linville@tuxdriver.com>
|
|
Remove CONFIG_ACPI_EC. It was always set the same as CONFIG_ACPI,
and it had no menu label, so there was no way to set it to anything
other than "y".
Per section 6.5.4 of the ACPI 3.0b specification,
OSPM must make Embedded Controller operation regions, accessed
via the Embedded Controllers described in ECDT, available before
executing any control method.
The ECDT table is optional, but if it is present, the above text
means that the EC it describes is a required part of the ACPI
subsystem, so CONFIG_ACPI_EC=n wouldn't make sense.
Signed-off-by: Bjorn Helgaas <bjorn.helgaas@hp.com>
Acked-by: Alexey Starikovskiy <astarikovskiy@suse.de>
Signed-off-by: Len Brown <len.brown@intel.com>
|
|
Remove CONFIG_ACPI_POWER. It was always set the same as CONFIG_ACPI,
and it had no menu label, so there was no way to set it to anything
other than "y".
The interfaces under CONFIG_ACPI_POWER (acpi_device_sleep_wake(),
acpi_power_transition(), etc) are called unconditionally from the
ACPI core, so we already depend on it always being present.
Signed-off-by: Bjorn Helgaas <bjorn.helgaas@hp.com>
Signed-off-by: Len Brown <len.brown@intel.com>
|
|
acpi_cm_sbs_init() doesn't do anything, so we can just remove it.
Signed-off-by: Bjorn Helgaas <bjorn.helgaas@hp.com>
Signed-off-by: Len Brown <len.brown@intel.com>
|
|
I don't think there's any point in cluttering the code with these.
Better to improve the documentation so *anybody* can figure out
what layer & level to use.
Signed-off-by: Bjorn Helgaas <bjorn.helgaas@hp.com>
Signed-off-by: Len Brown <len.brown@intel.com>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/tmlind/linux-omap-2.6
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/djbw/xscaleiop
|
|
When 'start' and 'end' are less than a cacheline apart and 'start' is
unaligned we are done after cleaning and invalidating the first
cacheline. So check for (start < end) which will not walk off into
invalid address ranges when (start > end).
This issue was caught by drivers/dma/dmatest.
2.6.27 is susceptible.
Cc: <stable@kernel.org>
Cc: Haavard Skinnemoen <haavard.skinnemoen@atmel.com>
Cc: Lothar WaÃ<9f>mann <LW@KARO-electronics.de>
Cc: Lennert Buytenhek <buytenh@marvell.com>
Cc: Eric Miao <eric.miao@marvell.com>
Signed-off-by: Dan Williams <dan.j.williams@intel.com>
|
|
As a result of the ptebits changes, we ended up marking device mappings
as normal memory on ARMv7 CPUs, resulting in undesirable behaviour with
serial ports and the like. While reviewing the section mapping table
entries, other errors in the memory type settings for devices were
detected and confirmed to prevent Xscale3 platforms booting.
Tested on:
OMAP34xx (ARMv7),
OMAP24xx (ARMv6),
OMAP16xx (ARM926T, ARMv5),
PXA311 (Xscale3),
PXA272 (Xscale),
PXA255 (Xscale),
IXP42x (Xscale),
S3C2410 (ARM920T, ARMv4T),
ARM720T (ARMv4T)
StrongARM-110 (ARMv4)
Acked-by: Tony Lindgren <tony@atomide.com>
Tested-by: Robert Jarzmik <robert.jarzmik@free.fr>
Tested-by: Mike Rapoport <mike@compulab.co.il>
Tested-by: Ben Dooks <ben-linux@fluff.org>
Tested-by: Anders Grafström <grfstrm@users.sourceforge.net>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
|
|
This fixes a regression introduced by 2c6e6db41f01b6b4eb98809350827c9678996698
"Minimize per_cpu reservations." That patch incorrectly used information about
what CPUs are possible that was not yet initialized by ACPI. The end result
was that per_cpu structures for offline CPUs were not initialized causing a
NULL pointer reference.
Since we cannot do the full acpi_boot_init() call any earlier, the simplest
fix is to just parse the MADT for SAPIC entries early to find the CPU
info. This should also allow for some cleanup of the code added by the
"Minimize per_cpu reservations". This patch just fixes the regressions, the
cleanup will come in a later patch.
Signed-off-by: Doug Chapman <doug.chapman@hp.com>
Signed-off-by: Alex Chiang <achiang@hp.com>
CC: Robin Holt <holt@sgi.com>
Signed-off-by: Tony Luck <tony.luck@intel.com>
|
|
No functional change, just reorder some config options and update
the "Power management and ACPI" label to match the defacto x86
standard.
Signed-off-by: Bjorn Helgaas <bjorn.helgaas@hp.com>
Signed-off-by: Tony Luck <tony.luck@intel.com>
|
|
As of 73bdf0a60e607f4b8ecc5aec597105976565a84f, the kernel needs
to know where modules are located in the virtual address space.
On ARM, we located this region between MODULE_START and MODULE_END.
Unfortunately, everyone else calls it MODULES_VADDR and MODULES_END.
Update ARM to use the same naming, so is_vmalloc_or_module_addr()
can work properly. Also update the comment on mm/vmalloc.c to
reflect that ARM also places modules in a separate region from the
vmalloc space.
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
|
|
This reverts commit c7ffa6c26277b403920e2255d10df849bd613380.
the assumptio of this change was that this would not break
any existing machine. Andrey Borzenkov reported troubles with
the ACPI reboot method: the system would hang on reboot, necessiating
a power cycle. Probably more systems are affected as well.
Also, there are patches queued up for v2.6.29 to disable virtualization
on emergency_restart() - which was the original motivation of
this change.
Reported-by: Andrey Borzenkov <arvidjaar@mail.ru>
Bisected-by: Andrey Borzenkov <arvidjaar@mail.ru>
Signed-off-by: Eduardo Habkost <ehabkost@redhat.com>
Acked-by: Avi Kivity <avi@redhat.com>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
|
|
Impact: right-align /proc/meminfo consistent with other fields
When the split-LRU patches added Inactive(anon) and Inactive(file) lines
to /proc/meminfo, all counts were moved two columns rightwards to fit in.
Now move x86's DirectMap lines two columns rightwards to line up.
Signed-off-by: Hugh Dickins <hugh@veritas.com>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/joro/linux-2.6-iommu into x86/urgent
|
|
Lazy flushing needs to take care of the unmap path too which is not yet
implemented and leads to stale IO/TLB entries. This is fixed by this
patch.
Signed-off-by: Joerg Roedel <joerg.roedel@amd.com>
|
|
If ubi_thread() exits but kthread_should_stop() is not true
then kthread_stop() will never return and cleanup thread
will forever stay in "D" state.
Signed-off-by: Vitaliy Gusev <vgusev@openvz.org>
Signed-off-by: Artem Bityutskiy <Artem.Bityutskiy@nokia.com>
|
|
'ubi_io_read_data()' may return EBADMSG in case of an ECC error,
and we should not panic because of this. We have CRC32 checksum
and may check the data. So just ignore the EBADMSG error.
This patch also fixes a minor spelling error at the same time.
Signed-off-by: Zoltan Sogor <weth@inf.u-szeged.hu>
Signed-off-by: Artem Bityutskiy <Artem.Bityutskiy@nokia.com>
|
|
The SAM9 watchdog driver is usable on the whole family of AT91SAM9 and
CAP9 processors.
Update the configuration to indicate this and allow the driver to be selected.
Signed-off-by: Andrew Victor <linux@maxim.org.za>
Signed-off-by: Wim Van Sebroeck <wim@iguana.be>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
|
|
The architecture header files were recently moved from
include/asm-arm/mach-at91/ to arch/arm/mach-at91/include/mach/.
The SAM9 watchdog driver still includes a header from the old location.
Signed-off-by: Andrew Victor <linux@maxim.org.za>
Signed-off-by: Wim Van Sebroeck <wim@iguana.be>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
|
|
Impact: fix rare x2apic hang
On x86, x2apic mode accesses for sending IPI's don't have serializing
semantics. If the IPI receivner refers(in lock-free fashion) to some
memory setup by the sender, the need for smp_mb() before sending the
IPI becomes critical in x2apic mode.
Add the smp_mb() in native_flush_tlb_others() before sending the IPI.
Signed-off-by: Suresh Siddha <suresh.b.siddha@intel.com>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
|
|
We currently oops with a divide error on starting a linear software
raid array consisting of at least two very small (< 500K) devices.
The bug is caused by the calculation of the hash table size which
tries to compute sector_div(sz, base) with "base" being zero due to
the small size of the component devices of the array.
Fix this by requiring the hash spacing to be at least one which
implies that also "base" is non-zero.
This bug has existed since about 2.6.14.
Cc: stable@kernel.org
Signed-off-by: Andre Noll <maan@systemlinux.org>
Signed-off-by: NeilBrown <neilb@suse.de>
|
|
Impact: fix warning message when PARAVIRT is set in config
Remove stale #ifdef components from our IRQ sizing logic.
x86/Voyager is the only holdout.
Signed-off-by: Yinghai Lu <yinghai@kernel.org>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
|
|
Impact: introduce new APIs
We want to deprecate cpumasks on the stack, as we are headed for
gynormous numbers of CPUs. Eventually, we want to head towards an
undefined 'struct cpumask' so they can never be declared on stack.
1) New cpumask functions which take pointers instead of copies.
(cpus_* -> cpumask_*)
2) Several new helpers to reduce requirements for temporary cpumasks
(cpumask_first_and, cpumask_next_and, cpumask_any_and)
3) Helpers for declaring cpumasks on or offstack for large NR_CPUS
(cpumask_var_t, alloc_cpumask_var and free_cpumask_var)
4) 'struct cpumask' for explicitness and to mark new-style code.
5) Make iterator functions stop at nr_cpu_ids (a runtime constant),
not NR_CPUS for time efficiency and for smaller dynamic allocations
in future.
6) cpumask_copy() so we can allocate less than a full cpumask eventually
(for alloc_cpumask_var), and so we can eliminate the 'struct cpumask'
definition eventually.
7) work_on_cpu() helper for doing task on a CPU, rather than saving old
cpumask for current thread and manipulating it.
8) smp_call_function_many() which is smp_call_function_mask() except
taking a cpumask pointer.
Note that this patch simply introduces the new functions and leaves
the obsolescent ones in place. This is to simplify the transition
patches.
Signed-off-by: Rusty Russell <rusty@rustcorp.com.au>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
|
|
This patch (as1159b) changes the timeout routines in the block core to
use round_jiffies_up(). There's no point in rounding the timer
deadline down, since if it expires too early we will have to restart
it.
The patch also removes some unnecessary tests when a request is
removed from the queue's timer list.
Signed-off-by: Alan Stern <stern@rowland.harvard.edu>
Signed-off-by: Jens Axboe <jens.axboe@oracle.com>
|
|
This patch (as1158b) adds round_jiffies_up() and friends. These
routines work like the analogous round_jiffies() functions, except
that they will never round down.
The new routines will be useful for timeouts where we don't care
exactly when the timer expires, provided it doesn't expire too soon.
Signed-off-by: Alan Stern <stern@rowland.harvard.edu>
Signed-off-by: Jens Axboe <jens.axboe@oracle.com>
|
|
Commit 0762b8bde9729f10f8e6249809660ff2ec3ad735 moved disk_get_part()
in front of recursive get on the whole disk, which caused removable
devices to try disk_get_part() before rescanning after a new media is
inserted, which might fail legit open attempts or give the old
partition.
This patch fixes the problem by moving disk_get_part() after
__blkdev_get() on the whole disk.
This problem was spotted by Borislav Petkov.
Signed-off-by: Tejun Heo <tj@kernel.org>
Tested-by: Borislav Petkov <petkovbb@gmail.com>
Signed-off-by: Jens Axboe <jens.axboe@oracle.com>
|
|
smp_mb() is needed (to make the memory operations visible globally) before
sending the ipi on the sender and the receiver (on Alpha atleast) needs
smp_read_barrier_depends() in the handler before reading the call_single_queue
list in a lock-free fashion.
On x86, x2apic mode register accesses for sending IPI's don't have serializing
semantics. So the need for smp_mb() before sending the IPI becomes more
critical in x2apic mode.
Remove the unnecessary smp_mb() in csd_flag_wait(), as the presence of that
smp_mb() doesn't mean anything on the sender, when the ipi receiver is not
doing any thing special (like memory fence) after clearing the CSD_FLAG_WAIT.
Signed-off-by: Suresh Siddha <suresh.b.siddha@intel.com>
Signed-off-by: Jens Axboe <jens.axboe@oracle.com>
|
|
Move the calling blk_delete_timer to later in end_that_request_last to
address an issue where blkdev_dequeue_request may have add a timer for the
request.
Signed-off-by: Mike Anderson <andmike@linux.vnet.ibm.com>
Acked-by: Tejun Heo <tj@kernel.org>
Signed-off-by: Jens Axboe <jens.axboe@oracle.com>
|
|
Block queue supports two usage models - one where block driver peeks
at the front of queue using elv_next_request(), processes it and
finishes it and the other where block driver peeks at the front of
queue, dequeue the request using blkdev_dequeue_request() and finishes
it. The latter is more flexible as it allows the driver to process
multiple commands concurrently.
These two inconsistent usage models affect the block layer
implementation confusing. For some, elv_next_request() is considered
the issue point while others consider blkdev_dequeue_request() the
issue point.
Till now the inconsistency mostly affect only accounting, so it didn't
really break anything seriously; however, with block layer timeout,
this inconsistency hits hard. Block layer considers
elv_next_request() the issue point and adds timer but SCSI layer
thinks it was just peeking and when the request can't process the
command right away, it's just left there without further processing.
This makes the request dangling on the timer list and, when the timer
goes off, the request which the SCSI layer and below think is still on
the block queue ends up in the EH queue, causing various problems - EH
hang (failed count goes over busy count and EH never wakes up),
WARN_ON() and oopses as low level driver trying to handle the unknown
command, etc. depending on the timing.
As SCSI midlayer is the only user of block layer timer at the moment,
moving blk_add_timer() to elv_dequeue_request() fixes the problem;
however, this two usage models definitely need to be cleaned up in the
future.
Signed-off-by: Tejun Heo <tj@kernel.org>
Signed-off-by: Jens Axboe <jens.axboe@oracle.com>
|
|
Define __BIOVEC_PHYS_MERGEABLE as the default implementation of
BIOVEC_PHYS_MERGEABLE, so that its available for reuse within an
arch-specific definition of BIOVEC_PHYS_MERGEABLE.
Signed-off-by: Jeremy Fitzhardinge <jeremy.fitzhardinge@citrix.com>
Signed-off-by: Jens Axboe <jens.axboe@oracle.com>
|
|
Signed-off-by: FUJITA Tomonori <fujita.tomonori@lab.ntt.co.jp>
Signed-off-by: Jens Axboe <jens.axboe@oracle.com>
|
|
Impact: clarify menuconfig text
Mention ACPI in the top-level menu to give a clue as to where
it lives. This matches what ia64 does.
Signed-off-by: Bjorn Helgaas <bjorn.helgaas@hp.com>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
|
|
Adding a spare to a raid10 doesn't cause recovery to start.
This is due to an silly type in
commit 6c2fce2ef6b4821c21b5c42c7207cb9cf8c87eda
and so is a bug in 2.6.27 and .28-rc.
Thanks to Thomas Backlund for bisecting to find this.
Cc: Thomas Backlund <tmb@mandriva.org>
Cc: stable@kernel.org
Signed-off-by: NeilBrown <neilb@suse.de>
|
|
It turns out that it is only safe to call blkdev_ioctl when the device
is actually open (as ->bd_disk is set to NULL on last close). And it
is quite possible for do_md_stop to be called when the device is not
open. So discard the call to blkdev_ioctl(BLKRRPART) which was
added in
commit 934d9c23b4c7e31840a895ba4b7e88d6413c81f3
It is just as easy to call this ioctl from userspace when needed (on
mdadm -S) so leave it out of the kernel
Signed-off-by: NeilBrown <neilb@suse.de>
|
|
Impact: make NR_IRQS big enough for system with lots of apic/pins
If lots of IO_APIC's are there (or can be there), size the same way
as 64-bit, depending on MAX_IO_APICS and NR_CPUS.
This fixes the boot problem reported by Ben Hutchings on a 32-bit
server with 5 IO-APICs and 240 IO-APIC pins.
Signed-off-by: Yinghai <yinghai@kernel.org>
Tested-by: Ben Hutchings <bhutchings@solarflare.com>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
|
|
Impact: fix boot hang on 32-bit systems with more than 224 IO-APIC pins
On some 32-bit systems with a lot of IO-APICs probe_nr_irqs() can
return a value larger than NR_IRQS. This will lead to probe_irq_on()
overrunning the irq_desc array.
I hit this when running net-next-2.6 (close to 2.6.28-rc3) on a
Supermicro dual Xeon system. NR_IRQS is 224 but probe_nr_irqs() detects
5 IOAPICs and returns 240. Here are the log messages:
Tue Nov 4 16:53:47 2008 ACPI: IOAPIC (id[0x01] address[0xfec00000] gsi_base[0])
Tue Nov 4 16:53:47 2008 IOAPIC[0]: apic_id 1, version 32, address 0xfec00000, GSI 0-23
Tue Nov 4 16:53:47 2008 ACPI: IOAPIC (id[0x02] address[0xfec81000] gsi_base[24])
Tue Nov 4 16:53:47 2008 IOAPIC[1]: apic_id 2, version 32, address 0xfec81000, GSI 24-47
Tue Nov 4 16:53:47 2008 ACPI: IOAPIC (id[0x03] address[0xfec81400] gsi_base[48])
Tue Nov 4 16:53:47 2008 IOAPIC[2]: apic_id 3, version 32, address 0xfec81400, GSI 48-71
Tue Nov 4 16:53:47 2008 ACPI: IOAPIC (id[0x04] address[0xfec82000] gsi_base[72])
Tue Nov 4 16:53:47 2008 IOAPIC[3]: apic_id 4, version 32, address 0xfec82000, GSI 72-95
Tue Nov 4 16:53:47 2008 ACPI: IOAPIC (id[0x05] address[0xfec82400] gsi_base[96])
Tue Nov 4 16:53:47 2008 IOAPIC[4]: apic_id 5, version 32, address 0xfec82400, GSI 96-119
Tue Nov 4 16:53:47 2008 ACPI: INT_SRC_OVR (bus 0 bus_irq 0 global_irq 2 high edge)
Tue Nov 4 16:53:47 2008 ACPI: INT_SRC_OVR (bus 0 bus_irq 9 global_irq 9 high level)
Tue Nov 4 16:53:47 2008 Enabling APIC mode: Flat. Using 5 I/O APICs
Signed-off-by: Ben Hutchings <bhutchings@solarflare.com>
Acked-by: Yinghai Lu <yhlu.kernel@gmail.com>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
|
|
deflate_mutex protects the globals lzo_mem and lzo_compress_buf. However,
jffs2_lzo_compress() unlocks deflate_mutex _before_ it has copied out the
compressed data from lzo_compress_buf. Correct this by moving the mutex
unlock after the copy.
In addition, document what deflate_mutex actually protects.
Cc: stable@kernel.org
Signed-off-by: Geert Uytterhoeven <Geert.Uytterhoeven@sonycom.com>
Acked-by: Richard Purdie <rpurdie@openedhand.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: David Woodhouse <David.Woodhouse@intel.com>
|
|
Fix printk format warnings in net/9p.
Built cleanly on 7 arches.
net/9p/client.c:820: warning: format '%llx' expects type 'long long unsigned int', but argument 4 has type 'u64'
net/9p/client.c:820: warning: format '%llx' expects type 'long long unsigned int', but argument 5 has type 'u64'
net/9p/client.c:867: warning: format '%llx' expects type 'long long unsigned int', but argument 4 has type 'u64'
net/9p/client.c:867: warning: format '%llx' expects type 'long long unsigned int', but argument 5 has type 'u64'
net/9p/client.c:932: warning: format '%llx' expects type 'long long unsigned int', but argument 5 has type 'u64'
net/9p/client.c:932: warning: format '%llx' expects type 'long long unsigned int', but argument 6 has type 'u64'
net/9p/client.c:982: warning: format '%llx' expects type 'long long unsigned int', but argument 4 has type 'u64'
net/9p/client.c:982: warning: format '%llx' expects type 'long long unsigned int', but argument 5 has type 'u64'
net/9p/client.c:1025: warning: format '%llx' expects type 'long long unsigned int', but argument 4 has type 'u64'
net/9p/client.c:1025: warning: format '%llx' expects type 'long long unsigned int', but argument 5 has type 'u64'
net/9p/client.c:1227: warning: format '%llx' expects type 'long long unsigned int', but argument 7 has type 'u64'
net/9p/client.c:1227: warning: format '%llx' expects type 'long long unsigned int', but argument 12 has type 'u64'
net/9p/client.c:1227: warning: format '%llx' expects type 'long long unsigned int', but argument 8 has type 'u64'
net/9p/client.c:1227: warning: format '%llx' expects type 'long long unsigned int', but argument 13 has type 'u64'
net/9p/client.c:1252: warning: format '%llx' expects type 'long long unsigned int', but argument 7 has type 'u64'
net/9p/client.c:1252: warning: format '%llx' expects type 'long long unsigned int', but argument 12 has type 'u64'
net/9p/client.c:1252: warning: format '%llx' expects type 'long long unsigned int', but argument 8 has type 'u64'
net/9p/client.c:1252: warning: format '%llx' expects type 'long long unsigned int', but argument 13 has type 'u64'
Signed-off-by: Randy Dunlap <randy.dunlap@oracle.com>
Signed-off-by: Eric Van Hensbergen <ericvh@gmail.com>
|
|
Signed-off-by: Roel Kluin <roel.kluin@gmail.com>
Signed-off-by: Eric Van Hensbergen <ericvh@gmail.com>
|
|
Removed duplicated #include <rdma/ib_verbs.h> in
net/9p/trans_rdma.c.
Signed-off-by: Huang Weiyi <weiyi.huang@gmail.com>
Signed-off-by: Eric Van Hensbergen <ericvh@gmail.com>
|
|
If a T or R fcall cannot be allocated, the function returns an error
but neglects to free the wait queue that was successfully allocated.
If it comes through again a second time this wq will be overwritten
with a new allocation and the old allocation will be leaked.
Also, if the client is subsequently closed, the close path will
attempt to clean up these allocations, so set the req fields to
NULL to avoid duplicate free.
Signed-off-by: Tom Tucker <tom@opengridcomputing.com>
Signed-off-by: Eric Van Hensbergen <ericvh@gmail.com>
|
|
T and R fcall are reused until the client is destroyed. There does
not need to be a special case for Flush
Signed-off-by: Tom Tucker <tom@opengridcomputing.com>
Signed-off-by: Eric Van Hensbergen <ericvh@gmail.com>
|
|
The client lock must be IRQ safe. Some of the lock acquisition paths
took regular spin locks.
Signed-off-by: Tom Tucker <tom@opengridcomputing.com>
Signed-off-by: Eric Van Hensbergen <ericvh@gmail.com>
|
|
The RDMA connection manager is fundamentally asynchronous.
Since the async callback context is the client pointer, the
transport in the client struct needs to be set prior to calling
the first async op.
Signed-off-by: Tom Tucker <tom@opengridcomputing.com>
Signed-off-by: Eric Van Hensbergen <ericvh@gmail.com>
|
|
Set mr->umem to NULL in mlx4_ib_alloc_fast_reg_mr(). Otherwise
ib_dereg_mr() may invoke ib_umem_release() on a random pointer value
and get an oops.
Signed-off-by: Vladimir Sokolovsky <vlad@mellanox.co.il>
Signed-off-by: Roland Dreier <rolandd@cisco.com>
|
|
Drivers want to be able to return DID_TRANSPORT_DISRUPTED and
have it do the right thing for commands like tape and passthrouh
as far as retries go. The LLDs previously used DID_BUS_BUSY or DID_ERROR
which followed the cmd->retries limit, but DID_TRANSPORT_DISRUPTED
was skipping that check so it could have caused a problem with tape
commands.
This patch has DID_TRANSPORT_DISRUPTED check the cmd->retries/cmd->allowed.
Signed-off-by: Mike Christie <mchristi@redhat.com>
Signed-off-by: James Bottomley <James.Bottomley@HansenPartnership.com>
|
|
Fix multiple problems found in the hexdump data:
- length calculation was wrong, traces were incomplete
- FC payloads were dumped in different record than the output
function tried to read
- minor fixes in output
- allow complete RSCN traces (up to 1024 bytes according to spec)
Signed-off-by: Christof Schmitt <christof.schmitt@de.ibm.com>
Signed-off-by: Swen Schillig <swen@vnet.ibm.com>
Signed-off-by: James Bottomley <James.Bottomley@HansenPartnership.com>
|
|
If an open port fsf request times out (in erp) the
corresponding erp_action member of the fsf
request need to set to NULL. If the port structure
will be removed later-on there will be still a
reference in the fsf request to the non existing
erp_action otherwise.
Signed-off-by: Martin Petermann <martin.petermann@de.ibm.com>
Signed-off-by: Christof Schmitt <christof.schmitt@de.ibm.com>
Signed-off-by: James Bottomley <James.Bottomley@HansenPartnership.com>
|
