summaryrefslogtreecommitdiffstats
AgeCommit message (Collapse)Author
2007-02-27qla3xxx: bugfix tx reset after stress conditions.Ron Mercer
To Reproduce the Problem: To reproduce this panic consistently, we run an intensive network application like 'netperf' and then switch to a different console. After waiting for a couple of seconds, you will see a tx reset has occured. Reason: We enable interrupts even if we were not running. Solution: Now we will enable interrupts only after we are ready to give up the poll routine. Signed-off-by: Ron Mercer <ron.mercer@qlogic.com> Signed-off-by: Jeff Garzik <jeff@garzik.org>
2007-02-27qla3xxx: Check return code from pci_map_single() in ↵Benjamin Li
ql_release_to_lrg_buf_free_list(), ql_populate_free_queue(), ql_alloc_large_buffers(), and ql3xxx_send() pci_map_single() could fail. We need to properly check the return code from pci_map_single(). If we can not properly map this address, then we should cleanup and return the proper return code. Signed-off-by: Benjamin Li <benjamin.li@qlogic.com> Signed-off-by: Ron Mercer <ron.mercer@qlogic.com> Signed-off-by: Jeff Garzik <jeff@garzik.org>
2007-02-27qla3xxx: bugfix: Fixed jumbo frame handling for 3032 chip.Ron Mercer
The scatter/gather lists were not being build correctly. When large frames spanned several buffers the chip would panic. Signed-off-by: Ron Mercer <ron.mercer@qlogic.com> Signed-off-by: Jeff Garzik <jeff@garzik.org>
2007-02-27qla3xxx: Clean up receive process.Ron Mercer
Signed-off-by: Ron Mercer <ron.mercer@qlogic.com> Signed-off-by: Jeff Garzik <jeff@garzik.org>
2007-02-27qla3xxx: Dynamically size the rx buffer queue based on the MTU.Ron Mercer
This change removes use of constants for rx buffer queue size and instead calculates the queue length based on what he MTU is set to. Signed-off-by: Ron Mercer <ron.mercer@qlogic.com> Signed-off-by: Jeff Garzik <jeff@garzik.org>
2007-02-27qla3xxx: Remove API to change MTU.Ron Mercer
This network device driver shares the same hardware as the qla4xxx iSCSI driver. Changing the MTU via the device interface will cause qla4xxx to crash as there is no way to make notification. Users wishing to change the MTU must do so using an iSCSI utility such as Qlogic SanSurfer. This forces the user to unload/reload this network device driver after the MTU value has been changed in flash. Signed-off-by: Ron Mercer <ron.mercer@qlogic.com> Signed-off-by: Jeff Garzik <jeff@garzik.org>
2007-02-27qla3xxx: Fix deadlock issue on error pathsBenjamin Li
1) Fix deadlock issue when in QL_RESET_ACTIVE state and traversing through the Link State Machine 2) Fix deadlock issue when ethtool would call ql_get_settings() 3) Fix deadlock issue when adaptor is ifup'ed but adaptor fails to initialize Signed-off-by: Benjamin Li <benjamin.li@qlogic.com> Signed-off-by: Ron Mercer <ron.mercer@qlogic.com> Signed-off-by: Jeff Garzik <jeff@garzik.org>
2007-02-27qla3xxx: Changed to use netdev_alloc_skb() from dev_alloc_skbBenjamin Li
Signed-off-by: Benjamin Li <benjamin.li@qlogic.com> Signed-off-by: Ron Mercer <ron.mercer@qlogic.com> Signed-off-by: Jeff Garzik <jeff@garzik.org>
2007-02-27qla3xxx: Remove unnecessary memset() in qla3xxx_send()Benjamin Li
We do not need to zero out the 64 byte MAC request I/O control block. By zeroing out the control block and setting it to proper fields is redundant work. This is because in the qla3xxx_send() function we will already set the proper fields in this structure. The unused fields are not looked at by the hardware and do not need to be zeroed out. Signed-off-by: Benjamin Li <benjamin.li@qlogic.com> Signed-off-by: Ron Mercer <ron.mercer@qlogic.com> Signed-off-by: Jeff Garzik <jeff@garzik.org>
2007-02-27qla3xxx: Return proper error codes when the 4022/4032 is being probedBenjamin Li
The return code was not properly set when when allocating memory or mapping memory failed. Depending on the stack, the return code would sometimes return 0, which indicates everything was ok, when in fact there was an error. This would cause trouble when the module was removed. Now, we will pass back the proper return code when an error occurs during the PCI probe. Signed-off-by: Benjamin Li <benjamin.li@qlogic.com> Signed-off-by: Ron Mercer <ron.mercer@qlogic.com> Signed-off-by: Jeff Garzik <jeff@garzik.org>
2007-02-27Alignment in mv643xx_ethRalf Baechle
The driver contains this little piece of candy: #if defined(CONFIG_DMA_NONCOHERENT) || defined(CONFIG_NOT_COHERENT_CACHE) #define ETH_DMA_ALIGN L1_CACHE_BYTES #else #define ETH_DMA_ALIGN 8 #endif Any reason why we're not using dma_get_cache_alignment() instead? Ralf Signed-off-by: Ralf Baechle <ralf@linux-mips.org> Signed-off-by: Jeff Garzik <jeff@garzik.org>
2007-02-27sgiseeq: Don't include unnecessary headerfiles.Ralf Baechle
Signed-off-by: Ralf Baechle <ralf@linux-mips.org> Signed-off-by: Jeff Garzik <jeff@garzik.org>
2007-02-27ucc_geth: use of_get_mac_address()Timur Tabi
Update ucc_geth_probe() to use function of_get_mac_address() to obtain the MAC address. Signed-off-by: Timur Tabi <timur@freescale.com> Signed-off-by: Jeff Garzik <jeff@garzik.org>
2007-02-27skge: comma consistencyStephen Hemminger
Use comma's consistently. Signed-off-by: Stephen Hemminger <shemminger@linux-foundation.org> Signed-off-by: Jeff Garzik <jeff@garzik.org>
2007-02-27skge: fix transmitter flow controlStephen Hemminger
It looks like the skge driver inherited another bug from the sk98lin code. If I send from 1000mbit port to a machine on 100mbit port, the switch should be doing hardware flow control, but no pause frames show up in the statistics. This is the analog of the recent sky2 fixes. The device needs to listen for multicast pause frames and then not discard them. Signed-off-by: Stephen Hemminger <shemminger@linux-foundation.org> Signed-off-by: Jeff Garzik <jeff@garzik.org>
2007-02-27myri10ge: workaround buggy adopted firmwaresBrice Goglin
Work around a bug which occurs when adopting firmware versions 1.4.4 though 1.4.11 where broadcasts are filtered as if they were multicasts. Signed-off-by: Brice Goglin <brice@myri.com> Signed-off-by: Jeff Garzik <jeff@garzik.org>
2007-02-27NetXen: Driver ifconfig fixAmit S. Kale
Signed-off-by: Amit S. Kale <amitkale@netxen.com> Signed-off-by: Jeff Garzik <jeff@garzik.org>
2007-02-27NetXen: Driver unload fixesAmit S. Kale
Signed-off-by: Amit S. Kale <amitkale@netxen.com> Signed-off-by: Jeff Garzik <jeff@garzik.org>
2007-02-27spidernet: maintainershipLinas Vepstas
Update driver support contact info. Signed-off-by: Linas Vepstas <linas@austin.ibm.com> Cc: Jens Osterkamp <Jens.Osterkamp@de.ibm.com> Cc: Kou Ishizaki <kou.ishizaki@toshiba.co.jp> Signed-off-by: Jeff Garzik <jeff@garzik.org>
2007-02-27spidernet: janitorial, typosLinas Vepstas
Janitorial patch. Undo long lines, fix typo in err msg. Signed-off-by: Linas Vepstas <linas@austin.ibm.com> Cc: Jens Osterkamp <Jens.Osterkamp@de.ibm.com> Cc: Kou Ishizaki <kou.ishizaki@toshiba.co.jp> Signed-off-by: Jeff Garzik <jeff@garzik.org>
2007-02-27spidernet: transmit raceLinas Vepstas
Multiple threads performing a transmit can race into the spidernet tx ring cleanup code. This puts the relevant check under a lock. Signed-off-by: Linas Vepstas <lins@austin.ibm.com> Cc: Jens Osterkamp <Jens.Osterkamp@de.ibm.com> Cc: Kou Ishizaki <kou.ishizaki@toshiba.co.jp> Signed-off-by: Jeff Garzik <jeff@garzik.org>
2007-02-27spidernet: fix racy double-free of skbLinas Vepstas
It appears that under certain circumstances, a race will result in a double-free of an skb. This patch null's out the skb pointer upon the skb free, avoiding the inadvertent deref of bogus data. The next patch fixes the actual race. Signed-off-by: Linas Vepstas <linas@austin.ibm.com> Cc: Jens Osterkamp <Jens.Osterkamp@de.ibm.com> Cc: Kou Ishizaki <kou.ishizaki@toshiba.co.jp> Signed-off-by: Jeff Garzik <jeff@garzik.org>
2007-02-27spidernet: separate hardware state from driver state.Linas Vepstas
This patch separates the hardware descriptor state from the driver descriptor state, per (old) suggestion from Ben Herrenschmidt. This compiles and boots and seems to work. Signed-off-by: Linas Vepstas <linas@austin.ibm.com> Cc: Jens Osterkamp <Jens.Osterkamp@de.ibm.com> Cc: Kou Ishizaki <kou.ishizaki@toshiba.co.jp> Signed-off-by: Jeff Garzik <jeff@garzik.org>
2007-02-27spidernet: move medium variable into card structJens Osterkamp
This moves the medium variable into the spidernet card structure. It renames the GMII_ variables to BCM54XX specific ones. Signed-off-by: Jens Osterkamp <jens@de.ibm.com> Signed-off-by: Linas Vepstas <linas@austin.ibm.com> Signed-off-by: Jeff Garzik <jeff@garzik.org>
2007-02-27spidernet: remove txram full loggingIshizaki Kou
This patches removes logging for SPIDER_NET_GTMFLLINT interrupts. Since the interrupts are not irregular, and they happen frequently when using 100Mbps network switches. Signed-off-by: Kou Ishizaki <kou.ishizaki@toshiba.co.jp> Signed-off-by: Linas Vepstas <linas@austin.ibm.com> Signed-off-by: Jeff Garzik <jeff@garzik.org>
2007-02-27spidernet: spidernet: add support for CellebKou Ishizaki
This patch adds or changes some HW specific settings for spider_net on Celleb. Signed-off-by: Kou Ishizaki <kou.ishizaki@toshiba.co.jp> Signed-off-by: Linas Vepstas <linas@austin.ibm.com> Signed-off-by: Jeff Garzik <jeff@garzik.org>
2007-02-27spidernet: load firmware when openKou Ishizaki
This patch moves calling init_firmware() from spider_net_probe() to spider_net_open() so as to use the driver by built-in. Signed-off-by: Kou Ishizaki <kou.ishizaki@toshiba.co.jp> Signed-off-by: Linas Vepstas <linas@austin.ibm.com> Signed-off-by: Jeff Garzik <jeff@garzik.org>
2007-02-27spidernet: autoneg support for CellebKou Ishizaki
Add auto negotiation support for Celleb. Signed-off-by: Kou Ishizaki <kou.ishizaki@toshiba.co.jp> Signed-off-by: Linas Vepstas <linas@austin.ibm.com> Signed-off-by: Jeff Garzik <jeff@garzik.org>
2007-02-27spidernet: compile break.Linas Vepstas
As of 2.6.20-git4, the spider_net driver does not compile. This appears to be due to some archaic usage involving kobjects. It also fixes a nasty double-free during ifdown of the interface. Signed-off-by: Linas Vepstas <linas@austin.ibm.com> Cc: Jens Osterkamp <Jens.Osterkamp@de.ibm.com> Cc: Kou Ishizaki <kou.ishizaki@toshiba.co.jp> Signed-off-by: Jeff Garzik <jeff@garzik.org>
2007-02-27sungem_phy: support bcm5461 phy, autoneg.Jens Osterkamp
This version moves the medium variable to the card specific structure and changes the GMII_* to BCM54XX_* #defines. This patch adds improved version of enable_fiber for both the 5421 and the 5461 phy. It is now possible to specify with these wether you want autonegotiation or not. This is needed for bladecenter switches where some expect autonegotiation and some dont seem to like this at all. Depending on this flag it sets phy->autoneg accordingly for the fiber mode. More importantly it implements proper read_link and poll_link functions for both phys which can handle both copper and fiber mode by determining the medium first and then branching to the required functions. For fiber they all work fine, for copper they are not tested but return the result of the genmii_* function anyway which is supposed to work. The patch moves the genmii_* functions around to avoid foreward declarations. Signed-off-by: Jens Osterkamp <jens@de.ibm.com> Signed-off-by: Arnd Bergmann <arnd.bergmann@de.ibm.com> Signed-off-by: Linas Vepstas <linas@austin.ibm.com> Signed-off-by: Jeff Garzik <jeff@garzik.org>
2007-02-27forcedeth: fix checksum feature in mcp65Ayaz Abdulla
This patch removes checksum offload feature in mcp65 chipsets as they are not supported in hw. Signed-Off-By: Ayaz Abdulla <aabdulla@nvidia.com> Signed-off-by: Jeff Garzik <jeff@garzik.org>
2007-02-27forcedeth: disable msixAyaz Abdulla
There seems to be an issue when both MSI-X is enabled and NAPI is configured. This patch disables MSI-X until the issue is root caused. Signed-Off-By: Ayaz Abdulla <aabdulla@nvidia.com> Signed-off-by: Jeff Garzik <jeff@garzik.org>
2007-02-27forcedeth: fixed missing call in napi pollAyaz Abdulla
The napi poll routine was missing the call to the optimized rx process routine. This patch adds the missing call for the optimized path. Signed-Off-By: Ayaz Abdulla <aabdulla@nvidia.com> Signed-off-by: Jeff Garzik <jeff@garzik.org>
2007-02-27[netdrvr] tc35815: fix obvious bugsJeff Garzik
* clear_page() use is wrong. We might have multiple pages. Use memset() instead. * Call pci_unregister_driver() in module exit. Signed-off-by: Jeff Garzik <jeff@garzik.org>
2007-02-26[MIPS] Make SMTC_IDLE_HOOK_DEBUG a proper option in Kconfig.debug.Ralf Baechle
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
2007-02-26[MIPS] Fix foobar in wiring up compat_sys_epoll_pwait syscall.Ralf Baechle
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
2007-02-26[MIPS] Always fixup unaligned accesses in kernel mode.Ralf Baechle
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
2007-02-26[MIPS] Fix dma_sync_*_for_device() functionsThomas Bogendoerfer
Signed-off-by: Thomas Bogendoerfer <tsbogend@alpha.franken.de> Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
2007-02-26[MIPS] Remove unreferenced _IOC_SLMASK macro in ioctl.h.Robert P. J. Day
Delete the definition of the apparently unreferenced macro _IOC_SLMASK. Signed-off-by: Robert P. J. Day <rpjday@mindspring.com> Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
2007-02-26[MIPS] SNI: MIPS_CPU_IRQ_BASE cleanupThomas Bogendoerfer
Use MIPS_CPU_IRQ_BASE instead of own define. Signed-off-by: Thomas Bogendoerfer <tsbogend@alpha.franken.de> Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
2007-02-26[MIPS] RTLX: Delete multiple definition of ret shaddowing each other.Ralf Baechle
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
2007-02-26[MIPS] RTLX, VPE: Make open actually atomic.Ralf Baechle
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
2007-02-26[MIPS] excite: Set serial driver iotype to UPIO_RM9000Thomas Koeller
Signed-off-by: Thomas Koeller <thomas.koeller@baslerweb.com> Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
2007-02-26[MIPS] excite: Rename CONFIG optionThomas Koeller
This change is purely cosmetical. Signed-off-by: Thomas Koeller <thomas.koeller@baslerweb.com> Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
2007-02-26[MIPS] Mark pcibios_fixup_device_resources() as __devinitAtsushi Nemoto
pcibios_fixup_device_resources() is called by pcibios_fixup_bus() which is marked as __devinit. Signed-off-by: Atsushi Nemoto <anemo@mba.ocn.ne.jp> Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
2007-02-26[MIPS] Kill redundant EXTRA_AFLAGSAtsushi Nemoto
Many Makefiles in arch/mips have EXTRA_AFLAGS := $(CFLAGS) line. This is redundant while AFLAGS contains $(cflags-y) and any options only listed in CFLAGS (not in cflags-y) should be unnecessary for asm sources. Signed-off-by: Atsushi Nemoto <anemo@mba.ocn.ne.jp> Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
2007-02-26[MIPS] RTLX: Handle signals when sleeping.Ralf Baechle
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
2007-02-26[MIPS] TB0287: Enable SM501 driver support in defconfigYoichi Yuasa
Signed-off-by: Yoichi Yuasa <yoichi_yuasa@tripeaks.co.jp> Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
2007-02-26Merge branch 'upstream-linus' of ↵Linus Torvalds
master.kernel.org:/pub/scm/linux/kernel/git/jgarzik/libata-dev * 'upstream-linus' of master.kernel.org:/pub/scm/linux/kernel/git/jgarzik/libata-dev: (51 commits) [libata] bump versions [libata] Trim trailing whitespace. [libata] sata_mv: Fix 50xx irq mask [libata] sata_mv: don't touch reserved bits in EDMA config register libata: Use new id_to_dma_mode function to tidy reporting in more drivers (minimally tested) pata_pcmcia: Fix oops in 2.6.21-rc1 Add id_to_dma_mode function for printing DMA modes sata_promise: simplify port setup sata_promise: fix 20619 new EH merge error [libata] ACPI: remove needless ->qc_issue hook existence test sata_vsc: refactor vsc_sata_interrupt and hook up error handling sata_sil: ignore and clear spurious IRQs while executing commands by polling sata_mv: fix pci_enable_msi() error handling pata_amd: fix an obvious bug in cable detection [libata] ata_piix: remove duplicate PCI IDs sata_nv: complain on spurious completion notifiers libata: test major version in ata_id_is_sata() sata_nv: kill old private BMDMA helper functions libata: fix remaining ap->id ahci: consider SDB FIS containing spurious NCQ completions HSM violation (regenerated) ...
2007-02-26Revert "[CPUFREQ] constify cpufreq_driver where possible."Linus Torvalds
This reverts commit aeeddc1435c37fa3fc844f31d39c185b08de4158, which was half-baked and broken. It just resulted in compile errors, since cpufreq_register_driver() still changes the 'driver_data' by setting bits in the flags field. So claiming it is 'const' _really_ doesn't work. Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
generated by cgit v1.2.3-70-g09d2 (git 2.46.0) at 2024-12-18 23:26:21 +0000