summaryrefslogtreecommitdiffstats
AgeCommit message (Collapse)Author
2009-03-21ax25: zero length frame filtering in AX25Bernard Pidoux
In previous commit 244f46ae6e9e18f6fc0be7d1f49febde4762c34b was introduced a zero length frame filter for ROSE protocole. This patch has the same purpose at AX25 frame level for the same reason. Empty frames have no meaning in AX25 protocole. Signed-off-by: Bernard Pidoux <f6bvp@amsat.org> Signed-off-by: David S. Miller <davem@davemloft.net>
2009-03-21ax25: SOCK_DEBUG message simplificationBernard Pidoux
This patch condenses two debug messages in one. Signed-off-by: Bernard Pidoux <f6bvp@amsat.org> Signed-off-by: David S. Miller <davem@davemloft.net>
2009-03-21fsl_pq_mdio: Revive Gianfar TBI PHY supportAnton Vorontsov
commit 1577ecef766650a57fceb171acee2b13cbfaf1d3 ("netdev: Merge UCC and gianfar MDIO bus drivers") broke the TSEC TBI PHY support: the driver now refuses to probe TBI MDIO buses as it doesn't know about "fsl,gianfar-tbi" compatible entry, and thus _probe() fails with -ENODEV status. Fix this by adding "fsl,gianfar-tbi" to the list of known Gianfar MDIO buses. Signed-off-by: Anton Vorontsov <avorontsov@ru.mvista.com> Acked-by: Andy Fleming <afleming@freescale.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2009-03-21ipv6: reorder struct inet6_ifaddr to remove padding on 64 bit buildsRichard Kennedy
reorder struct inet6_ifaddr to remove padding on 64 bit builds remove 8 bytes of padding so inet6_ifaddr becomes 192 bytes & fits into a smaller slab. Signed-off-by: Richard Kennedy <richard@rsk.demon.co.uk> Signed-off-by: David S. Miller <davem@davemloft.net>
2009-03-21gianfar: Fix build with CONFIG_PM enabledAnton Vorontsov
commit 4826857f1bf07f9c0f1495e9b05d125552c88a85 ("gianfar: pass the proper dev to DMA ops") introduced this build breakage: CC drivers/net/gianfar.o drivers/net/gianfar.c: In function 'gfar_suspend': drivers/net/gianfar.c:552: error: 'struct gfar_private' has no member named 'dev' drivers/net/gianfar.c: In function 'gfar_resume': drivers/net/gianfar.c:601: error: 'struct gfar_private' has no member named 'dev' make[2]: *** [drivers/net/gianfar.o] Error 1 Fix this by converting suspend and resume routines to use gfar_private->ndev. Signed-off-by: Anton Vorontsov <avorontsov@ru.mvista.com> Acked-by: Kumar Gala <galak@kernel.crashing.org> Signed-off-by: David S. Miller <davem@davemloft.net>
2009-03-21e100: add support for 82552 10/100 adapterBruce Allan
This patch enables support for the new Intel 82552 adapter (new PHY paired with the existing MAC in the ICH7 chipset). No new features are added to the driver, however there are minor changes due to updated registers and a few workarounds for hardware errata. Signed-off-by: Bruce Allan <bruce.w.allan@intel.com> Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2009-03-21Merge branch 'master' of git://git.infradead.org/~dwmw2/solos-2.6David S. Miller
2009-03-20e1000e: fixup merge errorArthur Jones
When merging into Jeff's tree: commit 5f66f208064f083aab5e55935d0575892e033b59 Author: Arthur Jones <ajones@riverbed.com> Date: Thu Mar 19 01:13:08 2009 +0000 e1000e: allow tx of pre-formatted vlan tagged packets We lost one line, this fixes that missing piece... Signed-off-by: Arthur Jones <ajones@riverbed.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2009-03-20Merge branch 'master' of ↵David S. Miller
master.kernel.org:/pub/scm/linux/kernel/git/davem/net-2.6 Conflicts: drivers/net/virtio_net.c
2009-03-20net: reorder struct Qdisc for better SMP performanceEric Dumazet
dev_queue_xmit() needs to dirty fields "state", "q", "bstats" and "qstats" On x86_64 arch, they currently span three cache lines, involving more cache line ping pongs than necessary, making longer holding of queue spinlock. We can reduce this to one cache line, by grouping all read-mostly fields at the beginning of structure. (Or should I say, all highly modified fields at the end :) ) Before patch : offsetof(struct Qdisc, state)=0x38 offsetof(struct Qdisc, q)=0x48 offsetof(struct Qdisc, bstats)=0x80 offsetof(struct Qdisc, qstats)=0x90 sizeof(struct Qdisc)=0xc8 After patch : offsetof(struct Qdisc, state)=0x80 offsetof(struct Qdisc, q)=0x88 offsetof(struct Qdisc, bstats)=0xa0 offsetof(struct Qdisc, qstats)=0xac sizeof(struct Qdisc)=0xc0 Signed-off-by: Eric Dumazet <dada1@cosmosbay.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2009-03-20dnet: remove duplicated #includeHuang Weiyi
Removed duplicated #include in drivers/net/dnet.c. Signed-off-by: Huang Weiyi <weiyi.huang@gmail.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2009-03-20ixgbe: Fixup the watchdog interrupt scheduling on 82599Jesse Brandeburg
The watchdog will schedule an interrupt to help make sure queues are cleaned in the case when an interrupt is missed, most likely due to very high load. On 82599, there are extra interrupt registers to account for the larger number of MSI-X vectors (64 total for 82599 vs. 18 total for 82598). These must be taken into account when performing this operation in the watchdog. Signed-off-by: Jesse Brandeburg <jesse.brandeburg@intel.com> Signed-off-by: Peter P Waskiewicz Jr <peter.p.waskiewicz.jr@intel.com> Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2009-03-20ixgbe: Correctly report Wake On LAN for 82599 KX4 devicesPJ Waskiewicz
ethtool isn't reporting the support level of WoL for 82599 KX4 devices. While the device does support WoL, ethtool was never updated to properly report the level of support, nor will it allow ethtool to modify the type of packets to listen for. Signed-off-by: Peter P Waskiewicz Jr <peter.p.waskiewicz.jr@intel.com> Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2009-03-20ixgbe: Fix PCI bus reporting on driver load for 82598 after 82599 mergePJ Waskiewicz
82598's PCI bus reporting on driver load was broken after 82599 merged. This results in incorrect reporting, and an erroneous warning message that the 82598 is in a PCIe slot that isn't fast enough to run 10GbE. Signed-off-by: Peter P Waskiewicz Jr <peter.p.waskiewicz.jr@intel.com> Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2009-03-20ixgb: refactor tx path to use skb_dma_map/unmapAlexander Duyck
This code updates ixgb so that it can use the skb_dma_map/unmap functions to map the buffers. In addition it also updates the tx hang logic to use time_stamp instead of dma to determine if it has detected a tx hang. Signed-off-by: Alexander Duyck <alexander.h.duyck@intel.com> Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2009-03-20e1000e: allow tx of pre-formatted vlan tagged packetsArthur Jones
As with igb, when the e1000e driver is fed 802.1q packets with hardware checksum on, it chokes with an error of the form: checksum_partial proto=81! As the logic there was not smart enough to look into the vlan header to pick out the encapsulated protocol. There are times when we'd like to send these packets out without having to configure a vlan on the interface. Here we check for the vlan tag and allow the packet to go out wiht the correct hardware checksum. Thanks to Kand Ly <kand@riverbed.com> for discovering the issue and the coming up with a solution. This patch is based upon his work. Fixups from Stephen Hemminger <shemminger@vyatta.com> and Alexander Duyck <alexander.h.duyck@intel.com> Signed-off-by: Arthur Jones <ajones@riverbed.com> Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com> CC: Stephen Hemminger <shemminger@vyatta.com> CC: Alexander Duyck <alexander.h.duyck@intel.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2009-03-20e1000e: fix dma error handling issuesAlexander Duyck
There were a few issues I noticed in e1000e. These include a double free of the skb if mapping fails, and the fact that context descriptors appear to be left in the descriptor ring after the failure. Signed-off-by: Alexander Duyck <alexander.h.duyck@intel.com> Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2009-03-20e1000e: add support for 82583 device idAlexander Duyck
Add device ID and related support for 82583 mac. Signed-off-by: Alexander Duyck <alexander.h.duyck@intel.com> Acked-by: Radheka Godse <radheka.godse@intel.com> Acked-by: Bruce Allan <bruce.w.allan@intel.com> Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2009-03-20smsc9420: fix big endian rx checksum offloadSteve Glendinning
The cpu_to_le16 here looks suspicious to me, I don't think we need it because put_unaligned_le16 also does this. I don't currently have any big endian hardware with a PCI bus available to test on, so I haven't been able to verify this. Signed-off-by: Steve Glendinning <steve.glendinning@smsc.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2009-03-20sunvnet: Convert to net_device_ops.David S. Miller
Signed-off-by: David S. Miller <davem@davemloft.net>
2009-03-19smsc911x: allow setting of mac addressSteve Glendinning
This patch replaces the generic eth_mac_addr function with one that also updates the hardware mac address registers. It also renames the existing smsc911x_set_mac_address function to smsc911x_hw_set_mac_address for clarity. Newer LAN911x and all LAN921x devices also support changing the mac address while the device is running, which is useful for some bonding modes. Signed-off-by: Steve Glendinning <steve.glendinning@smsc.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2009-03-19smsc911x: replace print_mac with %pMSteve Glendinning
Signed-off-by: Steve Glendinning <steve.glendinning@smsc.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2009-03-19smsc911x: define status word positions as constantsSteve Glendinning
The vast majority of bit constants in this driver are defined in the header file, but TX and RX status word bits are not. This patch (which should make no functional change) defines these, to make the driver slightly more readable. Signed-off-by: Steve Glendinning <steve.glendinning@smsc.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2009-03-19rtnetlink: add new value for DHCP added routesStephen Hemminger
To improve manageability, it would be good to be able to disambiguate routes added by administrator from those added by DHCP client. The only necessary kernel change is to add value to rtnetlink include file so iproute2 utility can use it. Signed-off-by: Stephen Hemminger <shemminger@vyatta.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2009-03-18bas_gigaset: correctly allocate USB interrupt transfer bufferTilman Schmidt
Every USB transfer buffer has to be allocated individually by kmalloc. Impact: bugfix, no functional change Signed-off-by: Tilman Schmidt <tilman@imap.cc> Tested-by: Kolja Waschk <kawk@users.sourceforge.net> Signed-off-by: David S. Miller <davem@davemloft.net>
2009-03-18smsc911x: reset last known duplex and carrier on openSteve Glendinning
smsc911x_phy_adjust_link is called periodically by the phy layer (as it's run in polling mode), and it only updates the hardware when it sees a change in duplex or carrier. This patch clears the last known values every time the interface is brought up, instead of only when the module is loaded. Without this patch the adjust_link function never updates the hardware after an ifconfig down; ifconfig up. On a full duplex link this causes the tx error counter to increment, even though packets are correctly transmitted, as the default MAC_CR register setting is for half duplex. The tx errors are "no carrier" errors, which should be ignored in full-duplex mode. When MAC_CR is set to "full duplex" mode they are correctly ignored by the hardware. Note that even with this patch the tx error counter can increment if packets are transmitted between "ifconfig up" and the first phy poll interval. An improved solution would use the phy interrupt with phylib, but I haven't managed to make this work 100% robustly yet. Signed-off-by: Steve Glendinning <steve.glendinning@smsc.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2009-03-18sh_eth: Fix mistake of the address of SH7763Nobuhiro Iwamatsu
Address of SH_TSU_ADDR and ARSTR of SH7763 was wrong. This revise it. Signed-off-by: Nobuhiro Iwamatsu <iwamatsu.nobuhiro@renesas.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2009-03-18sh_eth: Change handling of IRQNobuhiro Iwamatsu
Handling of IRQ of the SH7763/SH7764 CPU which sh_eth supported was changed. This revises it for this change. Signed-off-by: Nobuhiro Iwamatsu <iwamatsu.nobuhiro@renesas.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2009-03-18gianfar: pass the proper dev to DMA opsKumar Gala
We need to be passing the of_platform device struct into the DMA ops as its the one that has the archdata setup to know which low-level DMA ops we should be using (not the net_device one). This isn't an issue until we expect the archdata to be setup correctly. Signed-off-by: Kumar Gala <galak@kernel.crashing.org> Signed-off-by: David S. Miller <davem@davemloft.net>
2009-03-18netns: oops in ip[6]_frag_reasm incrementing statsJorge Boncompte [DTI2]
dev can be NULL in ip[6]_frag_reasm for skb's coming from RAW sockets. Quagga's OSPFD sends fragmented packets on a RAW socket, when netfilter conntrack reassembles them on the OUTPUT path you hit this code path. You can test it with something like "hping2 -0 -d 2000 -f AA.BB.CC.DD" With help from Jarek Poplawski. Signed-off-by: Jorge Boncompte [DTI2] <jorge@dti2.net> Signed-off-by: David S. Miller <davem@davemloft.net>
2009-03-18net: kfree(napi->skb) => kfree_skbRoel Kluin
struct sk_buff pointers should be freed with kfree_skb. Signed-off-by: Roel Kluin <roel.kluin@gmail.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2009-03-18net: fix sctp breakageAl Viro
broken by commit 5e739d1752aca4e8f3e794d431503bfca3162df4; AFAICS should be -stable fodder as well... Signed-off-by: Al Viro <viro@zeniv.linux.org.uk> Aced-by: Vlad Yasevich <vladislav.yasevich@hp.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2009-03-18tipc: fix non-const printf format argumentsStephen Hemminger
Fix warnings from current gcc about using non-const strings as printf args in TIPC. Compile tested only (not a TIPC user). Signed-off-by: Stephen Hemminger <shemminger@vyatta.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2009-03-18ipv6: fix display of local and remote sit endpointsBjørn Mork
This fixes the regressions cause by commit 1326c3d5a4b792a2b15877feb7fb691f8945d203 (v2.6.28-rc6-461-g23a12b1) broke the display of local and remote addresses of an SIT tunnel in iproute2. nt->parms is used by ipip6_tunnel_init() and therefore need to be initialized first. Tracked as http://bugzilla.kernel.org/show_bug.cgi?id=12868 Reported-by: Jan Engelhardt <jengelh@medozas.de> Signed-off-by: Bjørn Mork <bjorn@mork.no> Signed-off-by: David S. Miller <davem@davemloft.net>
2009-03-18net: Document /proc/sys/net/core/netdev_budgetStanislaw Gruszka
The NAPI poll parameter netdev_budget is not documented in kernel-docs. Since it may have a substantial effect on at least some network loads, it should be. Signed-off-by: Stanislaw Gruszka <sgruszka@redhat.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2009-03-18tcp: remove parameter from tcp_recv_urg().Rami Rosen
This patch removes an unused parameter (addr_len) from tcp_recv_urg() method in net/ipv4/tcp.c. Signed-off-by: Rami Rosen <ramirose@gmail.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2009-03-18tulip: fix crash on iface up with shirq debugKyle McMartin
Tulip is currently doing request_irq before it has done its initialization. This is usually not a problem because it hasn't enable interrupts yet, but with DEBUG_SHIRQ on, we call the irq handler when registering the interrupt as a sanity check. This can result in a NULL ptr dereference, so call tulip_init_ring before request_irq, and add a free_ring function to do the freeing now shared with tulip_close. Tested with a shell loop running ifup, ifdown in a loop a few hundred times with DEBUG_SHIRQ on. Signed-off-by: Kyle McMartin <kyle@redhat.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2009-03-18virtio_net: Make virtio_net support carrier detectionPantelis Koukousoulas
Impact: Make NetworkManager work with virtio_net For now the semantics are simple: There is always carrier. This allows a seamless experience with e.g., qemu/kvm where NetworkManager just configures and sets up everything automagically. If/when a generally agreed-upon way to control carrier on/off in the emulator/hypervisor level emerges, it will be trivial to extend the driver to support that too, but for now even this 2-liner makes user experience that much better. Signed-off-by: Pantelis Koukousoulas <pktoss@gmail.com> Signed-off-by: Rusty Russell <rusty@rustcorp.com.au> Signed-off-by: David S. Miller <davem@davemloft.net>
2009-03-18bonding: Fix updating of speed/duplex changesJay Vosburgh
This patch corrects an omission from the following commit: commit f0c76d61779b153dbfb955db3f144c62d02173c2 Author: Jay Vosburgh <fubar@us.ibm.com> Date: Wed Jul 2 18:21:58 2008 -0700 bonding: refactor mii monitor The un-refactored code checked the link speed and duplex of every slave on every pass; the refactored code did not do so. The 802.3ad and balance-alb/tlb modes utilize the speed and duplex information, and require it to be kept up to date. This patch adds a notifier check to perform the appropriate updating when the slave device speed changes. Signed-off-by: Jay Vosburgh <fubar@us.ibm.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2009-03-18ipv6: Fix incorrect disable_ipv6 behaviorBrian Haley
Fix the behavior of allowing both sysctl and addrconf_dad_failure() to set the disable_ipv6 parameter without any bad side-effects. If DAD fails and accept_dad > 1, we will still set disable_ipv6=1, but then instead of allowing an RA to add an address then immediately fail DAD, we simply don't allow the address to be added in the first place. This also lets the user set this flag and disable all IPv6 addresses on the interface, or on the entire system. Signed-off-by: Brian Haley <brian.haley@hp.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2009-03-18a2065: skb_padto cleanupsDave Jones
Remove unnecessary check (skb_padto does the same check) Remove unnecessary duplicate variable Remove unnecessary clearing of padded part of skb. Signed-off-by: Dave Jones <davej@redhat.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2009-03-18bnx2: Fix problem of using wrong IRQ handler.Michael Chan
The MSI-X handler was chosen before the call to pci_enable_msix(). If MSI-X was not available, the wrong MSI-X handler would be used in INTA mode. This would cause a screaming interrupt problem because INTA would not be cleared by the MSI-X handler. Fixed by assigning MSI-X handler after pci_enable_msix() returns successfully. Also update version to 1.9.3. Thomas Chenault <thomas_chenault@dell.com> helped us find this problem. Signed-off-by: Michael Chan <mchan@broadcom.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2009-03-17Merge branch 'master' of ↵David S. Miller
git://git.kernel.org/pub/scm/linux/kernel/git/linville/wireless-next-2.6
2009-03-17Merge branch 'master' of ↵David S. Miller
master.kernel.org:/pub/scm/linux/kernel/git/davem/net-2.6 Conflicts: drivers/net/igb/igb_main.c drivers/net/qlge/qlge_main.c drivers/net/wireless/ath9k/ath9k.h drivers/net/wireless/ath9k/core.h drivers/net/wireless/ath9k/hw.c
2009-03-17Merge branch 'master' of ↵David S. Miller
git://git.kernel.org/pub/scm/linux/kernel/git/linville/wireless-2.6
2009-03-17netxen: fix firmware download warningsDhananjay Phadke
Fix following warnings, by using integer firmware types. drivers/net/netxen/netxen_nic_hw.c: In function 'netxen_load_firmware': drivers/net/netxen/netxen_nic_hw.c:1146: warning: comparison with string literal results in unspecified behavior drivers/net/netxen/netxen_nic_hw.c:1146: warning: comparison with string literal results in unspecified behavior drivers/net/netxen/netxen_nic_hw.c:1146: warning: comparison with string literal results in unspecified behavior drivers/net/netxen/netxen_nic_hw.c:1159: warning: comparison with string literal results in unspecified behavior drivers/net/netxen/netxen_nic_hw.c:1159: warning: comparison with string literal results in unspecified behavior drivers/net/netxen/netxen_nic_hw.c:1159: warning: comparison with string literal results in unspecified behavior Reported-by: Stephen Rothwell <sfr@canb.auug.org.au> Signed-off-by: Dhananjay Phadke <dhananjay@netxen.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2009-03-17Merge branch 'master' of ↵David S. Miller
git://git.kernel.org/pub/scm/linux/kernel/git/kaber/nf-2.6
2009-03-17gro: Fix legacy path napi_complete crashHerbert Xu
On the legacy netif_rx path, I incorrectly tried to optimise the napi_complete call by using __napi_complete before we reenable IRQs. This simply doesn't work since we need to flush the held GRO packets first. This patch fixes it by doing the obvious thing of reenabling IRQs first and then calling napi_complete. Reported-by: Frank Blaschka <blaschka@linux.vnet.ibm.com> Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au> Signed-off-by: David S. Miller <davem@davemloft.net>
2009-03-17gro: Fix vlan/netpoll check againHerbert Xu
Jarek Poplawski pointed out that my previous fix is broken for VLAN+netpoll as if netpoll is enabled we'd end up in the normal receive path instead of the VLAN receive path. This patch fixes it by calling the VLAN receive hook. Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au> Signed-off-by: David S. Miller <davem@davemloft.net>
2009-03-17solos: Disable DMA until we have an FPGA update with it actually implemented.David Woodhouse
Signed-off-by: David Woodhouse <David.Woodhouse@intel.com>
generated by cgit v1.2.3-70-g09d2 (git 2.46.0) at 2024-12-19 08:23:51 +0000