| Age | Commit message (Collapse) | Author |
|---|
|
|
|
This fixes a typo in commit 2a2a64714d9c40f7705c4de1e79a5b855c7211a9
"Disable MWAIT via DMI on broken Compal board".
It allows the nomwait dmi check to actually detect the Acer 5220.
Signed-off-by: Dennis Jansen <dennis.jansen@web.de>
Tested-by: Dennis Jansen <dennis.jansen@web.de>
Acked-by: Zhao Yakui <yakui.zhao@intel.com>
Signed-off-by: Andi Kleen <ak@linux.intel.com>
|
|
Signed-off-by: Milan Broz <mbroz@redhat.com>
Signed-off-by: Andi Kleen <ak@linux.intel.com>
|
|
The drivers below do not use LINUX_VERSION_CODE nor KERNEL_VERSION.
drivers/char/pcmcia/ipwireless/tty.c
drivers/char/synclink_gt.c
drivers/char/xilinx_hwicap/xilinx_hwicap.c
This patch removes the said #include <version.h>.
Signed-off-by: Huang Weiyi <weiyi.huang@gmail.com>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/tip/linux-2.6-tip
* 'core-fixes-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/linux-2.6-tip:
lockdep: fix build if CONFIG_PROVE_LOCKING not defined
lockdep: use WARN() in kernel/lockdep.c
lockdep: spin_lock_nest_lock(), checkpatch fixes
lockdep: build fix
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/tip/linux-2.6-tip
* 'sched-fixes-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/linux-2.6-tip:
sched: scale sysctl_sched_shares_ratelimit with nr_cpus
sched: fix rt-bandwidth hotplug race
sched: fix the race between walk_tg_tree and sched_create_group
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/tip/linux-2.6-tip
* 'x86-fixes-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/linux-2.6-tip: (32 commits)
x86: add MAP_STACK mmap flag
x86: fix section mismatch warning - spp_getpage()
x86: change init_gdt to update the gdt via write_gdt, rather than a direct write.
x86-64: fix overlap of modules and fixmap areas
x86, geode-mfgpt: check IRQ before using MFGPT as clocksource
x86, acpi: cleanup, temp_stack is used only when CONFIG_SMP is set
x86: fix spin_is_contended()
x86, nmi: clean UP NMI watchdog failure message
x86, NMI: fix watchdog failure message
x86: fix /proc/meminfo DirectMap
x86: fix readb() et al compile error with gcc-3.2.3
arch/x86/Kconfig: clean up, experimental adjustement
x86: invalidate caches before going into suspend
x86, perfctr: don't use CCCR_OVF_PMI1 on Pentium 4Ds
x86, AMD IOMMU: initialize dma_ops after sysfs registration
x86m AMD IOMMU: cleanup: replace LOW_U32 macro with generic lower_32_bits
x86, AMD IOMMU: initialize device table properly
x86, AMD IOMMU: use status bit instead of memory write-back for completion wait
x86: silence mmconfig printk
x86, msr: fix NULL pointer deref due to msr_open on nonexistent CPUs
...
|
|
I noticed that sysctl_check.o was the largest object file in
a allnoconfig build in kernel/*.
36243 0 0 36243 8d93 kernel/sysctl_check.o
This is because it was default y and && EMBEDDED. But I don't
really see a need for a non kernel developer to have their
sysctls checked all the time.
So move the Kconfig into the kernel debugging section and
also drop the default y and the EMBEDDED check.
Signed-off-by: Andi Kleen <ak@linux.intel.com>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
|
|
* master.kernel.org:/home/rmk/linux-2.6-arm: (38 commits)
[ARM] 5191/1: ARM: remove CVS keywords
[ARM] pxafb: fix the warning of incorrect lccr when lcd_conn is specified
[ARM] pxafb: add flag to specify output format on LDD pins when base is RGBT16
[ARM] pxafb: fix the incorrect configuration of GPIO77 as ACBIAS for TFT LCD
[ARM] 5198/1: PalmTX: PCMCIA fixes
[ARM] Fix a pile of broken watchdog drivers
[ARM] update mach-types
[ARM] 5196/1: fix inline asm constraints for preload
[ARM] 5194/1: update .gitignore
[ARM] add proc-macros.S include to proc-arm940 and proc-arm946
[ARM] 5192/1: ARM TLB: add v7wbi_{possible,always}_flags to {possible,always}_tlb_flags
[ARM] 5193/1: Wire up missing syscalls
[ARM] traps: don't call undef hook functions with spinlock held
[ARM] 5183/2: Provide Poodle LoCoMo GPIO names
[ARM] dma-mapping: provide sync_range APIs
[ARM] dma-mapping: improve type-safeness of DMA translations
[ARM] Kirkwood: instantiate the orion_spi driver in the platform code
[ARM] prevent crashing when too much RAM installed
[ARM] Kirkwood: Instantiate mv_xor driver
[ARM] Orion: Instantiate mv_xor driver for 5182
...
|
|
The exported copy of videodev2.h contains this line:
#define #include <sys/time.h>
This is because for some reason it defines __user for itself -- despite
the fact that we remove all instances of __user when exporting headers.
_All_ pointers in userspace are user pointers. Fix it by removing the
unnecessary '#define __user' from the file.
The new headers ivtv.h and ivtvfb.h would have the same problem... if
whoever put them there had actually remembered to add them to the Kbuild
file while he was at it. Fix those too, and export them as was
presumably intended.
Note that includes of <linux/compiler.h> are also stripped by the header
export process, so those don't need to be conditional.
Signed-off-by: David Woodhouse <David.Woodhouse@intel.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
Acked-by: Hans Verkuil <hverkuil@xs4all.nl>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
|
|
Try to comment away a little of the confusion between mm's vm_area_struct
vm_flags and vmalloc's vm_struct flags: based on an idea by Ulrich Drepper.
Signed-off-by: Hugh Dickins <hugh@veritas.com>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
|
|
This patch removes CVS keywords that weren't updated for a long time.
Signed-off-by: Adrian Bunk <bunk@kernel.org>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
|
|
The newly introduced "lcd_conn" field for connected LCD panel type will
cause the original code to generate the warnings of incorrect lccr*.
This is unnecessary since well encoded LCD_* flags will not generate
incorrect combinition of lccr* bits. Skip the check if "lcd_conn" is
specified.
Signed-off-by: Eric Miao <eric.miao@marvell.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
|
|
Another fix of inconsistent shift of the LCD_BIAS_ACTIVE_* and
LCD_PCLK_EDGE_* is also included.
Signed-off-by: Eric Miao <eric.miao@marvell.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
|
|
Signed-off-by: Eric Miao <eric.miao@marvell.com>
Tested-by: Robert Jarzmik <robert.jarzmik@free.fr>
Tested-by: Alex Osborne <ato@meshy.org>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
|
|
Fix GPIO handling in the PCMCIA driver.
Signed-off-by: Marek Vasut <marek.vasut@gmail.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
|
|
These patches from Adrian fix:
- ixp4xx_wdt: 20d35f3e50ea7e573f9568b9fce4e98523aaee5d
CC drivers/watchdog/ixp4xx_wdt.o
ixp4xx_wdt.c:32: error: expected '=', ',', ';', 'asm' or '__attribute__'
ixp4xx_wdt.c: In function 'wdt_enable':
ixp4xx_wdt.c:41: error: 'wdt_lock' undeclared (first use in this
ixp4xx_wdt.c:41: error: (Each undeclared identifier is reported only
ixp4xx_wdt.c:41: error: for each function it appears in.)
ixp4xx_wdt.c: In function 'wdt_disable':
ixp4xx_wdt.c:52: error: 'wdt_lock' undeclared (first use in this
ixp4xx_wdt.c: In function 'ixp4xx_wdt_init':
ixp4xx_wdt.c:186: error: 'wdt_lock' undeclared (first use in this
make[3]: *** [drivers/watchdog/ixp4xx_wdt.o] Error 1
- at91rm9200_wdt: 2760600da2a13d5a2a335ba012d0f3ad5df4c098
CC drivers/watchdog/at91rm9200_wdt.o
at91rm9200_wdt.c:188: error: 'at91_wdt_ioctl' undeclared here (not in a
make[3]: *** [drivers/watchdog/at91rm9200_wdt.o] Error 1
- wdt285: d0e58eed05f9baf77c4f75e794ae245f6dae240a
CC [M] drivers/watchdog/wdt285.o
wdt285.c: In function 'footbridge_watchdog_init':
wdt285.c:211: error: 'KERN_WARN' undeclared (first use in this function)
wdt285.c:211: error: (Each undeclared identifier is reported only once
wdt285.c:211: error: for each function it appears in.)
wdt285.c:212: error: expected ')' before string constant
make[3]: *** [drivers/watchdog/wdt285.o] Error 1
And this patch from rmk:
- s3c2410_wdt: 41dc8b72e37c514f7332cbc3f3dd864910c2a1fa
CC drivers/watchdog/s3c2410_wdt.o
s3c2410_wdt.c: In function `s3c2410wdt_start':
s3c2410_wdt.c:161: warning: `return' with a value, in function returning void
Reported-by: Adrian Bunk <bunk@kernel.org>
Signed-off-by: Adrian Bunk <bunk@kernel.org>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
|
|
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
|
|
With gcc 4.3 and later, a pointer that has already been dereferenced is
assumed not to be null since it should have caused a segmentation fault
otherwise, hence any subsequent test against NULL is optimized away.
Current inline asm constraint used in the implementation of prefetch()
makes gcc believe that the pointer is dereferenced even though the PLD
instruction does not load any data and does not cause a segmentation
fault on null pointers, which causes all sorts of interesting results
when reaching the end of a linked lists for example.
Let's use a better constraint to properly represent the actual usage of
the pointer value.
Problem reported by Chris Steel.
Signed-off-by: Nicolas Pitre <nico@marvell.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/jmorris/security-testing-2.6
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/jmorris/security-testing-2.6:
security: Fix setting of PF_SUPERPRIV by __capable()
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/cooloney/blackfin-2.6
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/cooloney/blackfin-2.6: (33 commits)
Blackfin arch: hook up some missing new system calls
Blackfin arch: fix missing digit in SCLK range checking
Blackfin arch: do not muck with the UART during boot -- let the serial driver worry about it
Blackfin arch: clear EMAC_SYSTAT during IRQ init rather than early head.S as we dont need it setup that early
Blackfin arch: use %pF when printing out the double fault address so we get symbol names
Blackfin arch: add support for the BlackStamp board
Blackfin arch: Allow ins functions to have a low latency version
Blackfin arch: Print out doublefault addresses, so debug can occur
Blackfin arch: shuffle related prototypes together -- no functional changes
Blackfin arch: move fixed code defines into fixed_code.h as very few things actually need to know these details
Blackfin arch: mark some functions as __init as they are only called from __init functions
Blackfin arch: delete dead prototypes
Blackfin arch: cleanup cache lock code
Blackfin arch: workaround SIC_IWR1 reset bug, by keeping MDMA0/1 always enabled in SIC_IWR1.
Blackfin arch: Fix bug - when expanding the trace buffer, it does not print out the decoded instruction.
Blackfin arch: Fix Bug - System with EMAC driver enabled - Core not idling
Blackfin arch: delete unused cache functions
Blackfin arch: convert L2 defines to be the same as the L1 defines
Blackfin arch: unify the duplicated portions of __start and split mach-specific pieces into _mach_early_start where they will be easier to trim over time
Blackfin arch: add asm/thread_info.h for THREAD_SIZE define
...
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/ak/linux-acpi-2.6
* 'release-2.6.27' of git://git.kernel.org/pub/scm/linux/kernel/git/ak/linux-acpi-2.6:
cpuidle: Make ladder governor honor latency requirements fully
cpuidle: Menu governor fix wrong usage of measured_us
cpuidle: Do not use poll_idle unless user asks for it
x86: Fix ioremap off by one BUG
|
|
|
|
ladder governor only honored latency requirement when promoting C-states.
Instead. it should check for latency requirement on each idle call,
and demote to appropriate C-state when there is a latency requirement change.
Signed-off-by: Venkatesh Pallipadi <venkatesh.pallipadi@intel.com>
Signed-off-by: Andi Kleen <ak@linux.intel.com>
|
|
There is a bug in menu governor where we have
if (data->elapsed_us < data->elapsed_us + measured_us)
with measured_us already having elapsed_us added in tickless case here
unsigned int measured_us =
cpuidle_get_last_residency(dev) + data->elapsed_us;
Also, it should be last_residency, not measured_us, that need to be used to
do comparing and distinguish between expected & non-expected events.
Refactor menu_reflect() to fix these two problems.
Signed-off-by: Venkatesh Pallipadi <venkatesh.pallipadi@intel.com>
Signed-off-by: Wei Gang <gang.wei@intel.com>
Signed-off-by: Andi Kleen <ak@linux.intel.com>
|
|
poll_idle was added to CPUIDLE, just as a low latency idle handler, to be
used in cases when user desires CPUs not to enter any idle state at all. It
was supposed to be a run time idle=poll option to the user. But, it was indeed
getting used during normal menu and ladder governor default case, with no
special user setting (Reported by Linus Torvalds).
Change below ensures that poll_idle will not be used unless user explicitly
asks pm_qos infrastructure for zero latency requirement.
Signed-off-by: Venkatesh Pallipadi <venkatesh.pallipadi@intel.com>
Signed-off-by: Andi Kleen <ak@linux.intel.com>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/tiwai/sound-2.6
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tiwai/sound-2.6:
ALSA: wm8990: Implement speaker volume PGA
ALSA: wm8990: Fix routing of left DAC to speaker mixer
ALSA: virtuoso: add Xonar D1 support
|
|
Not all AMD K8 have 6 VID pins, contrary to what was assumed in
commit 116d0486bdefc11f71e567cadf0c47f788b4dd06. This commit broke
support of older CPU models which have only 5 VID pins:
http://bugzilla.kernel.org/show_bug.cgi?id=11329
We need two entries in the hwmon-vid table, one for 5-bit VID models
(K8 revision <= E) and one for 6-bit VID models (K8 revision >= F).
This fixes bug #11329.
Signed-off-by: Jean Delvare <khali@linux-fr.org>
Acked-by: Frank Myhr <fmyhr@fhmtech.com>
Tested-by: Jean-Luc Coulon <jean.luc.coulon@gmail.com>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
|
|
as per this discussion:
http://lkml.org/lkml/2008/8/12/423
Pardo reported that 64-bit threaded apps, if their stacks exceed the
combined size of ~4GB, slow down drastically in pthread_create() - because
glibc uses MAP_32BIT to allocate the stacks. The use of MAP_32BIT is
a legacy hack - to speed up context switching on certain early model
64-bit P4 CPUs.
So introduce a new flag to be used by glibc instead, to not constrain
64-bit apps like this.
glibc can switch to this new flag straight away - it will be ignored
by the kernel. If those old CPUs ever matter to anyone, support for
it can be implemented.
Signed-off-by: Ingo Molnar <mingo@elte.hu>
Acked-by: Ulrich Drepper <drepper@gmail.com>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
|
|
* git://git.kernel.org/pub/scm/linux/kernel/git/sfrench/cifs-2.6:
[CIFS] mount of IPC$ breaks with iget patch
[CIFS] remove trailing whitespace
[CIFS] if get root inode fails during mount, cleanup tree connection
|
|
|
|
This moves it to being a tty operation. That removes special cases and now
also means that resize can be picked up by um and other non vt consoles
which may have a resize operation.
Signed-off-by: Alan Cox <alan@redhat.com>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
|
|
* 'linux-next' of git://git.infradead.org/~dedekind/ubifs-2.6: (29 commits)
UBIFS: xattr bugfixes
UBIFS: remove unneeded check
UBIFS: few commentary fixes
UBIFS: fix budgeting request alignment in xattr code
UBIFS: improve arguments checking in debugging messages
UBIFS: always set i_generation to 0
UBIFS: correct spelling of "thrice".
UBIFS: support splice_write
UBIFS: minor tweaks in commit
UBIFS: reserve more space for index
UBIFS: print pid in dump function
UBIFS: align inode data to eight
UBIFS: improve budgeting checks
UBIFS: correct orphan deletion order
UBIFS: fix typos in comments
UBIFS: do not union creat_sqnum and del_cmtno
UBIFS: optimize deletions
UBIFS: increment commit number earlier
UBIFS: remove another unneeded function parameter
UBIFS: remove unneeded function parameter
...
|
|
If CONFIG_PROVE_LOCKING not defined, then no dependency information
is available.
Signed-off-by: Stephen Hemminger <shemminger@vyatta.com>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
|
|
as per this discussion:
http://lkml.org/lkml/2008/8/12/423
Pardo reported that 64-bit threaded apps, if their stacks exceed the
combined size of ~4GB, slow down drastically in pthread_create() - because
glibc uses MAP_32BIT to allocate the stacks. The use of MAP_32BIT is
a legacy hack - to speed up context switching on certain early model
64-bit P4 CPUs.
So introduce a new flag to be used by glibc instead, to not constrain
64-bit apps like this.
glibc can switch to this new flag straight away - it will be ignored
by the kernel. If those old CPUs ever matter to anyone, support for
it can be implemented.
Signed-off-by: Ingo Molnar <mingo@elte.hu>
Acked-by: Ulrich Drepper <drepper@gmail.com>
|
|
WARNING: vmlinux.o(.text+0x17a3e): Section mismatch in reference from the function set_pte_vaddr_pud() to the function .init.text:spp_getpage()
The function set_pte_vaddr_pud() references
the function __init spp_getpage().
This is often because set_pte_vaddr_pud lacks a __init
annotation or the annotation of spp_getpage is wrong.
spp_getpage is called from __init (__init_extra_mapping) and
non __init (set_pte_vaddr_pud) functions, so it can't be __init.
Unfortunately it calls alloc_bootmem_pages which is __init,
but does it only when bootmem allocator is available (after_bootmem == 0).
So annotate it accordingly.
Signed-off-by: Marcin Slusarz <marcin.slusarz@gmail.com>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
Cc: H. Peter Anvin <hpa@zytor.com>
|
|
write.
By writing directly, a memory access violation can occur whilst
hotplugging a CPU if the entry was previously marked read-only.
Signed-off-by: Alex Nixon <alex.nixon@citrix.com>
Cc: Jeremy Fitzhardinge <Jeremy.Fitzhardinge@citrix.com>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
|
|
* 'for-linus' of git://neil.brown.name/md:
md: cancel check/repair requests when recovery is needed
Allow raid10 resync to happening in larger chunks.
Allow faulty devices to be removed from a readonly array.
Don't let a blocked_rdev interfere with read request in raid5/6
Fail safely when trying to grow an array with a write-intent bitmap.
Restore force switch of md array to readonly at reboot time.
Make writes to md/safe_mode_delay immediately effective.
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/dtor/input
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/dtor/input:
Input: xilinx_ps2 - fix warning
Input: bcm5974 - implement autosuspend support
Input: bcm5974 - add driver for Macbook Air and Pro Penryn touchpads
Input: paper over a bug in Synaptics X driver
Input: evdev - split EVIOCGBIT handlig into a separate function
Input: i8042 - Add Dritek quirk for Acer TravelMate 4280
Input: xpad - add Pelican Eclipse D-Pad to the list of devices
Input: gpio-keys - make gpio_keys_device_driver static
Input: gpio-keys - fix possible NULL pointer dereference
Input: wm97xx - enable sub-drivers by default
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/ak/linux-acpi-2.6
* 'release-2.6.27' of git://git.kernel.org/pub/scm/linux/kernel/git/ak/linux-acpi-2.6:
ACPI: Fix thermal shutdowns
ACPI: bounds check IRQ to prevent memory corruption
ACPI: Avoid bogus EC timeout when EC is in Polling mode
ACPI : Add the EC dmi table to fix the incorrect ECDT table
ACPI: Properly clear flags on false-positives and send uevent on sudden unplug
acpi: trivial cleanups
acer-wmi: Fix wireless and bluetooth on early AMW0 v2 laptops
ACPI: WMI: Set instance for query block calls
ACPICA: Additional error checking for pathname utilities
ACPICA: Fix possible memory leak in Unload() operator
ACPICA: Fix memory leak when deleting thermal/processor objects
|
|
David reported that his Niagra spend a little too much time in
tg_shares_up(), which considering he has a large cpu count makes sense.
So scale the ratelimit value with the number of cpus like we do for
other controls as well.
Reported-by: David Miller <davem@davemloft.net>
Signed-off-by: Peter Zijlstra <a.p.zijlstra@chello.nl>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
|
|
Sam Ravnborg did the build-test that the direct header file move works,
I'm just committing it.
This is a pure move:
mkdir arch/alpha/include
git mv include/asm-alpha arch/alpha/include/asm
with no other changes.
Requested-and-tested-by: Sam Ravnborg <sam@ravnborg.org>
Cc: Richard Henderson <rth@twiddle.net>
Cc: Ivan Kokshaysky <ink@jurassic.park.msu.ru>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
|
|
Jean Delvare's machine triggered this BUG
acpi_os_map_memory phys ffff0000 size 65535
------------[ cut here ]------------
kernel BUG at arch/x86/mm/pat.c:233!
with ACPI in the backtrace.
Adding some debugging output showed that ACPI calls
acpi_os_map_memory phys ffff0000 size 65535
And ioremap/PAT does this check in 32bit, so addr+size wraps and the BUG
in reserve_memtype() triggers incorrectly.
BUG_ON(start >= end); /* end is exclusive */
But reserve_memtype already uses u64:
int reserve_memtype(u64 start, u64 end,
so the 32bit truncation must happen in the caller. Presumably in ioremap
when it passes this information to reserve_memtype().
This patch does this computation in 64bit.
http://bugzilla.kernel.org/show_bug.cgi?id=11346
Signed-off-by: Andi Kleen <ak@linux.intel.com>
|
|
|
|
The latest revisions of the WM8990 provide a programmable gain amplifier
for the speaker - configure the register cache and implement controls
for this. Older revisions of the device ignore writes to these controls.
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
|
|
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
|
|
A fuzzed fileystem image failed with OMFS when the extent count was
used in a loop without being checked against the max number of extents.
It also provoked a signed division for an array index that was checked
as if unsigned, leading to index by -1.
omfsck will be updated to fix these cases, in the meantime bail out
gracefully.
Reported-by: Eric Sesterhenn <snakebyte@gmx.de>
Signed-off-by: Bob Copeland <me@bobcopeland.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
|
|
Testing with a modified fsfuzzer reveals a couple of locations in omfs
where filesystem variables are ultimately used as loop counters with
insufficient sanity checking. In this case, dir->i_size is used to
compute the number of buckets in the directory hash. If too large,
readdir will overrun a buffer.
Since it's an invariant that dir->i_size is equal to the sysblock
size, and we already sanity check that, just use that value instead.
This fixes the following oops:
BUG: unable to handle kernel paging request at c978e004
IP: [<c032298e>] omfs_readdir+0x18e/0x32f
Oops: 0000 [#1] PREEMPT DEBUG_PAGEALLOC
Modules linked in:
Pid: 4796, comm: ls Not tainted (2.6.27-rc2 #12)
EIP: 0060:[<c032298e>] EFLAGS: 00010287 CPU: 0
EIP is at omfs_readdir+0x18e/0x32f
EAX: c978d000 EBX: 00000000 ECX: cbfcfaf8 EDX: cb2cf100
ESI: 00001000 EDI: 00000800 EBP: cb2d3f68 ESP: cb2d3f0c
DS: 007b ES: 007b FS: 0000 GS: 0033 SS: 0068
Process ls (pid: 4796, ti=cb2d3000 task=cb175f40 task.ti=cb2d3000)
Stack: 00000002 00000000 00000000 c018a820 cb2d3f94 cb2cf100 cbfb0000 ffffff10
cbfb3b80 cbfcfaf8 000001c9 00000a09 00000000 00000000 00000000 cbfcfbc8
c9697000 cbfb3b80 22222222 00001000 c08e6cd0 cb2cf100 cbfb3b80 cb2d3f88
Call Trace:
[<c018a820>] ? filldir64+0x0/0xcd
[<c018a9f2>] ? vfs_readdir+0x56/0x82
[<c018a820>] ? filldir64+0x0/0xcd
[<c018aa7c>] ? sys_getdents64+0x5e/0xa0
[<c01038bd>] ? sysenter_do_call+0x12/0x31
=======================
Code: 00 89 f0 89 f3 0f ac f8 14 81 e3 ff ff 0f 00 48 8d
14 c5 b8 01 00 00 89 45 cc 89 55 f0 e9 8c 01 00 00 8b 4d c8 8b 75 f0 8b
41 18 <8b> 54 30 04 8b 04 30 31 f6 89 5d dc 89 d1 8b 55 b8 0f c8 0f c9
Reported-by: Eric Sesterhenn <snakebyte@gmx.de>
Signed-off-by: Bob Copeland <me@bobcopeland.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
|
|
m68k fails to build with these functions inlined in completion.h. Move
them out of line into sched.c and export them to avoid this problem.
Signed-off-by: Dave Chinner <david@fromorbit.com>
Cc: Geert Uytterhoeven <geert@linux-m68k.org>
Cc: Ingo Molnar <mingo@elte.hu>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
|
|
When reviewing a recent patch I noticed a potential trouble spot in the
registration of new SPI devices. The SPI master driver is told to set
the device up before adding it to the driver model, so that it's always
properly set up when probe() is called. (This is important, because in
the case of inverted chipselects, this device can make the bus misbehave
until it's properly deselected. It's got to be set up even if no driver
binds to the device.)
The trouble spot is that it doesn't first verify that no other device
has been added using that chipselect. If such a device has been added,
its configuration gets trashed. (Fortunately this has not been a common
error!)
The fix here adds an explicit check, and a mutex to protect the relevant
critical region.
[akpm@linux-foundation.org: make the lock local to spi_add_device()]
Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
|
