summaryrefslogtreecommitdiffstats
AgeCommit message (Collapse)Author
2009-07-30Merge branch 'master' of ↵David S. Miller
git://git.kernel.org/pub/scm/linux/kernel/git/linville/wireless-2.6
2009-07-30drm/i915: Add support for dual-channel LVDS on 8xx.ling.ma@intel.com
This corresponds to a fix to UMS back in 2007. Fixes fd.o bug #20115. Signed-off-by: Ma Ling <ling.ma@intel.com> Signed-off-by: Eric Anholt <eric@anholt.net>
2009-07-30drm/i915: Return disconnected for SDVO DVI when there's no digital EDID.ling.ma@intel.com
The patch fixed a bug on MP965-D. When VGA is connected to a DVI-I connector, it incorrectly shows sdvo dvi as connected. Signed-off-by: Ma Ling <ling.ma@intel.com> [anholt: hand-resolved against previous commit and fixed up commit message] Signed-off-by: Eric Anholt <eric@anholt.net>
2009-07-30[SCSI] sd: Avoid sending extended inquiry to legacy devicesMartin K. Petersen
Some USB devices crash when we send them an inquiry with the EVPD bit set, regardless of page requested (i.e. including page 0). We only need the extended inquiry to gain access to VPD pages 0xB0 and 0xB1. These appeared in SBC2 and SBC3 respectively, so we can restrict sending the extended inquiry to devices reporting SPC3 or higher. This fixes bugzilla.kernel.org #13657. Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com> [jejb: added comment] Signed-off-by: James Bottomley <James.Bottomley@HansenPartnership.com>
2009-07-30quota: Silence lockdep on quota_onJan Kara
Commit d01730d74d2b0155da50d44555001706294014f7 didn't completely fix the problem since we still take dqio_mutex and i_mutex in the wrong order. Move taking of i_mutex further down (luckily it's needed only for updating inode flags) below where dqio_mutex is taken. Tested-by: Valdis Kletnieks <valdis.kletnieks@vt.edu> Signed-off-by: Jan Kara <jack@suse.cz>
2009-07-30udf: Fix loading of VAT inode when drive wrongly reports number of recorded ↵Jan Kara
blocks VAT inode is located in the last block recorded block of the medium. When the drive errorneously reports number of recorded blocks, we failed to load the VAT inode and thus mount the medium. This patch makes kernel try to read VAT inode from the last block of the device if it is different from the last recorded block. Signed-off-by: Jan Kara <jack@suse.cz>
2009-07-30[SCSI] libsas: fix wide port hotplug issuesTom Peng
Hotplug of phys which form wide ports simply does not work at the moment. Fix this by adding checks at the hotplug points to see if the attached sas address of the phy already exists (in which case it's part of a wide port) and act accordingly. Signed-off-by: Tom Peng <tom_peng@usish.com> Signed-off-by: Jack Wang <jack_wang@usish.com> Signed-off-by: Lindar Liu <lindar_liu@usish.com> Signed-off-by: Kevin Ao <aoqingyun@usish.com> [jejb: tidied up coding, fixed an error case and made TRUE/FALSE lower case to fix a ppc64 compile error in linux-next] Signed-off-by: James Bottomley <James.Bottomley@HansenPartnership.com>
2009-07-30Btrfs: be more polite in the async caching threadsChris Mason
The semaphore used by the async caching threads can prevent a transaction commit, which can make the FS appear to stall. This releases the semaphore more often when a transaction commit is in progress. Signed-off-by: Chris Mason <chris.mason@oracle.com>
2009-07-30[SCSI] libfc: fix a circular locking warning during sending RRQVasu Dev
Currently the fc_exch_rrq is called with fc_exch's ex_lock held. The fc_exch_rrq allocates new exch and that requires taking ex_lock again after EM lock. This locking order causes warning, see more details on this warning at :- http://www.open-fcoe.org/pipermail/devel/2009-July/003251.html This patch fixes this by dropping the ex_lock before calling fc_exch_rrq(). The fc_exch_rrq needs to grab ex_lock lock again to schedule RRQ retry and in the meanwhile fc_exch_reset could occur before ex_lock is grabbed inside fc_exch_rrq. So to handle this case, this patch adds additional check to detect fc_exch_reset after ex_lock acquired and in case the fc_exch_reset occurred then abandons the RRQ retry and releases the exch. Signed-off-by: Vasu Dev <vasu.dev@intel.com> Signed-off-by: Robert Love <robert.w.love@intel.com> Signed-off-by: James Bottomley <James.Bottomley@HansenPartnership.com>
2009-07-30[SCSI] qla4xxx: Remove hiwat code so scsi eh does not get escalated when we ↵Karen Higgins
can make progress Removed unnecessary hiwat code to free up the number available IOCBs. Eliminates unnecessary eh_ escalations due to inability to obtain IOCB pkt for marker. v2. - Remove define not used anymore and fix req_q_coun accounting. Signed-off-by: Karen Higgins <karen.higgins@qlogic.com> [michaelc: ported patch from qlogic.com driver to upstream] Signed-off-by: Mike Christie <michaelc@cs.wisc.edu> Signed-off-by: James Bottomley <James.Bottomley@HansenPartnership.com>
2009-07-30[SCSI] qla4xxx: Fix srb lookup in qla4xxx_eh_device_resetKaren Higgins
eh_device_reset may be called from scsi error handler or sg_reset, etc. When called from sg_reset, there will not be an associated srb. The driver should lookup the corresponding device handle given information from the supplied cmd structure and should not assume that there exists an srb. Signed-off-by: Karen Higgins <karen.higgins@qlogic.com> Signed-off-by: Mike Christie <michaelc@cs.wisc.edu> Signed-off-by: James Bottomley <James.Bottomley@HansenPartnership.com>
2009-07-30[SCSI] qla4xxx: Fix Driver Fault Recovery CompletionKaren Higgins
Fixed driver bug where adapter recovery did not complete if there were outstanding commands detected on that host adapter. Signed-off-by: Karen Higgins <karen.higgins@qlogic.com> Signed-off-by: Mike Christie <michaelc@cs.wisc.edu> Signed-off-by: James Bottomley <James.Bottomley@HansenPartnership.com>
2009-07-30[SCSI] qla4xxx: add timeout handlerMike Christie
Recently dm-multipath began calling blk_abort_queue. This causes all the commands/request running on the path to have the timeout function called. If a path does go down, and the LLD returns DID_*, dm-multpiath will eventually get this error and begin to call the cmd timeout handler. qla4xxx currently does not set a timed out handler and so the default one could return BLK_EH_NOT_HANDLED and end up firing the scsi eh and stopping IO to all paths on the host when only one path is affected. For software and offload iscsi we have a timed out handler already. This patch adds a driver specific one to qla4xxx because there are some ddb->state and session->state and command completion races that are better handled in the LLD. This also handles the problem where if the session is down, we do not need the scsi eh to run until the transport code has tried to reconnect us. Signed-off-by: Mike Christie <michaelc@cs.wisc.edu> Signed-off-by: James Bottomley <James.Bottomley@HansenPartnership.com>
2009-07-30[SCSI] qla4xxx: Correct Extended Sense Data ErrorsKaren Higgins
Fixed sense data errors occurring above the first 32 bytes, as required by some third party applications. Sense data in the first 32 bytes has always been correct. Patch updated to use srb data variables instead of scsi command scratchpad data area, as scratchpad area is already used. Also, corrected debug print alignment bug in dump_buffer routine. Changed KERN_DEBUG to KERN_INFO in printk statements in this routine. Changed version number to 5.01.00-k9 Signed-off-by: Karen Higgins <karen.higgins@qlogic.com> [michaelc: fixed checkpath.pl errors] Signed-off-by: Mike Christie <michaelc@cs.wisc.edu> Signed-off-by: James Bottomley <James.Bottomley@HansenPartnership.com>
2009-07-30[SCSI] libiscsi: disable bh in and abort handler.Mike Christie
The session lock can be held in the scsi eh thread or the completion paths run from the net softirq. This disables bhs in iscsi_eh_abort when taking the session lock. Signed-off-by: Mike Christie <michaelc@cs.wisc.edu> Signed-off-by: James Bottomley <James.Bottomley@HansenPartnership.com>
2009-07-30[SCSI] zfcp: Fix tracing of request id for abort requestsChristof Schmitt
The trace record for SCSI abort requests has a field for the request id of the request to be aborted. Put the real request id instead of zero. Reviewed-by: Swen Schillig <swen@vnet.ibm.com> Signed-off-by: Christof Schmitt <christof.schmitt@de.ibm.com> Signed-off-by: James Bottomley <James.Bottomley@HansenPartnership.com>
2009-07-30[SCSI] zfcp: Fix wka port processingSwen Schillig
Under certain conditions it is possible that a WKA port ist not opened within the expected timeframe of half a second. In this situation the WKA port remains in the state OPENING preventing any succeding request to open the port. This led to unrecoverable remote ports. Fixing this by always setting an appropriate WKA port status before leaving the function and removing the timeout value here since it's not needed here because the general timeout processing would deal with it if required. Signed-off-by: Swen Schillig <swen@vnet.ibm.com> Signed-off-by: Christof Schmitt <christof.schmitt@de.ibm.com> Signed-off-by: James Bottomley <James.Bottomley@HansenPartnership.com>
2009-07-30[SCSI] zfcp: avoid double notify in lowmem scenarioSwen Schillig
In a LOWMEM condition an ERP notification would have been sent twice causing an unpredictable behaviour of the ERP. Signed-off-by: Swen Schillig <swen@vnet.ibm.com> Signed-off-by: Christof Schmitt <christof.schmitt@de.ibm.com> Signed-off-by: James Bottomley <James.Bottomley@HansenPartnership.com>
2009-07-30[SCSI] zfcp: Add port only once to FC transport classChristof Schmitt
When calling fc_remote_port_add make sure to not call it again before fc_remote_port_delete has been called. In other words, ensure to create a new fc_rport, then delete it, then create a new one again. Reviewed-by: Swen Schillig <swen@vnet.ibm.com> Signed-off-by: Christof Schmitt <christof.schmitt@de.ibm.com> Signed-off-by: James Bottomley <James.Bottomley@HansenPartnership.com>
2009-07-30[SCSI] zfcp: Recover from stalled outbound queueChristof Schmitt
Depending on interruptions on some storage systems, the complete channel can stall which looks like an outbound queue stall to Linux. When trying to acquire a free SBAL for a non-SCSI command, zfcp waits for 5 seconds for a free slot to appear. This is the right place to detect a queue stall: If the wait times out, we assume a stalled queue and try to recover this. The overall strategy should be to trigger the erp from specific events, and not try an overall escalation from one failed port to a full-blown queue recovery. If we manage to send a command, the status codes for this command or a timeout will trigger the right follow-on actions. Reviewed-by: Swen Schillig <swen@vnet.ibm.com> Signed-off-by: Christof Schmitt <christof.schmitt@de.ibm.com> Signed-off-by: James Bottomley <James.Bottomley@HansenPartnership.com>
2009-07-30[SCSI] zfcp: Fix erp escalation procedureChristof Schmitt
If an action fails, retry it until the erp count exceeds the threshold. If there is something fundamentally wrong, the FSF layer will trigger a more appropriate action depending on the FSF status codes. The followup for successful actions is a different followup than retrying failed actions, so split the code two functions to make this clear. Reviewed-by: Swen Schillig <swen@vnet.ibm.com> Signed-off-by: Christof Schmitt <christof.schmitt@de.ibm.com> Signed-off-by: James Bottomley <James.Bottomley@HansenPartnership.com>
2009-07-30[SCSI] zfcp: Fix logic for physical port closeChristof Schmitt
After closing the port, we want it to be "not open" to consider the action to be successful. Reviewed-by: Swen Schillig <swen@vnet.ibm.com> Signed-off-by: Christof Schmitt <christof.schmitt@de.ibm.com> Signed-off-by: James Bottomley <James.Bottomley@HansenPartnership.com>
2009-07-30[SCSI] zfcp: Use -EIO for SBAL allocation failuresChristof Schmitt
-ENOMEM is for memory allocation problems, -EIO for queue/SBAL allocation problems. Reviewed-by: Swen Schillig <swen@vnet.ibm.com> Signed-off-by: Christof Schmitt <christof.schmitt@de.ibm.com> Signed-off-by: James Bottomley <James.Bottomley@HansenPartnership.com>
2009-07-30[SCSI] zfcp: Use unchained mode for small ct and els requestsChristof Schmitt
The ELS ADISC and the GID_PN requests sent from zfcp fit into unchained FSF requests. Change the FSF allocation logic to use unchained requests whenever possible where everything fits in one SBAL. This avoids acquiring more SBALs than necessary, especially during zfcp recovery when things might be stalled. Reviewed-by: Swen Schillig <swen@vnet.ibm.com> Signed-off-by: Christof Schmitt <christof.schmitt@de.ibm.com> Signed-off-by: James Bottomley <James.Bottomley@HansenPartnership.com>
2009-07-30[SCSI] zfcp: Use correct flags for zfcp_erp_notifyChristof Schmitt
zfcp_erp_notify uses the ZFCP_ERP_STATUS_* flags, so it is ZFCP_STATUS_ERP_LOWMEM instead of ZFCP_ERP_NOMEM. Signalling ZFCP_ERP_FAILED is not necessary, the missing d_id will show that the nameserver did not return the d_id. Reviewed-by: Swen Schillig <swen@vnet.ibm.com> Signed-off-by: Christof Schmitt <christof.schmitt@de.ibm.com> Signed-off-by: James Bottomley <James.Bottomley@HansenPartnership.com>
2009-07-30[SCSI] zfcp: Return -ENOMEM for allocation failures in zfcp_fsfChristof Schmitt
When a fsf_req or a qtcb cannot be allocated return -ENOMEM instead of -EIO. Reviewed-by: Swen Schillig <swen@vnet.ibm.com> Signed-off-by: Christof Schmitt <christof.schmitt@de.ibm.com> Signed-off-by: James Bottomley <James.Bottomley@HansenPartnership.com>
2009-07-30[SCSI] zfcp: Acquire qdio_stat_lock when reading the queue utilizationChristof Schmitt
req_q_util is not atomic, so the qdio_stat_lock must be held when reading this variable. Reviewed-by: Swen Schillig <swen@vnet.ibm.com> Signed-off-by: Christof Schmitt <christof.schmitt@de.ibm.com> Signed-off-by: James Bottomley <James.Bottomley@HansenPartnership.com>
2009-07-30[SCSI] zfcp: Fix invalid command orderSwen Schillig
We should not modify the port status after triggering an ERP action for the port. It is not guaranteed which status is finally active when the ERP action is performed. This can lead to situations which are unwanted and hard to debug in case of a failure. Signed-off-by: Swen Schillig <swen@vnet.ibm.com> Signed-off-by: Christof Schmitt <christof.schmitt@de.ibm.com> Signed-off-by: James Bottomley <James.Bottomley@HansenPartnership.com>
2009-07-30Btrfs: preserve commit_root for async cachingYan Zheng
The async block group caching code uses the commit_root pointer to get a stable version of the extent allocation tree for scanning. This copy of the tree root isn't going to change and it significantly reduces the complexity of the scanning code. During a commit, we have a loop where we update the extent allocation tree root. We need to loop because updating the root pointer in the tree of tree roots may allocate blocks which may change the extent allocation tree. Right now the commit_root pointer is changed inside this loop. It is more correct to change the commit_root pointer only after all the looping is done. Signed-off-by: Yan Zheng <zheng.yan@oracle.com> Signed-off-by: Chris Mason <chris.mason@oracle.com>
2009-07-30GFS2: remove dcache entries for remote deleted inodesBenjamin Marzinski
When a file is deleted from a gfs2 filesystem on one node, a dcache entry for it may still exist on other nodes in the cluster. If this happens, gfs2 will be unable to free this file on disk. Because of this, it's possible to have a gfs2 filesystem with no files on it and no free space. With this patch, when a node receives a callback notifying it that the file is being deleted on another node, it schedules a new workqueue thread to remove the file's dcache entry. Signed-off-by: Benjamin Marzinski <bmarzins@redhat.com> Signed-off-by: Steven Whitehouse <swhiteho@redhat.com>
2009-07-30GFS2: Fix incorrent statfs consistency checkBenjamin Marzinski
Since both linked and unlinked inodes are counted by rgd->rd_dinodes, It makes no sense to count them with the used data blocks (first check that I changed), it makes sense to count them with the linked inodes (second check), and it makes no sense to care if there are more unlinked inodes than linked ones. This fixes these errors. Signed-off-by: Benjamin Marzinski <bmarzins@redhat.com> Signed-off-by: Steven Whitehouse <swhiteho@redhat.com>
2009-07-30GFS2: Don't put unlikely reclaim candidates on the reclaim list.Benjamin Marzinski
GFS2 was placing far too many glocks on the reclaim list that were not good candidates for freeing up from cache. These locks would sit there and repeatedly get scanned to see if they could be reclaimed, wasting a lot of time when there was memory pressure. This fix does more checks on the locks to see if they are actually likely to be removable from cache. Signed-off-by: Benjamin Marzinski <bmarzins@redhat.com> Signed-off-by: Steven Whitehouse <swhiteho@redhat.com>
2009-07-30GFS2: Don't try and dealloc own inodeSteven Whitehouse
When searching for unlinked, but still allocated inodes during block allocation, avoid the block relating to the inode that is doing the allocation. This fixes a hang caused when an unlinked, but still open, inode tries to allocate some more blocks and lands up finding itself during the search for deallocatable inodes. Signed-off-by: Steven Whitehouse <swhiteho@redhat.com>
2009-07-30GFS2: Fix panic in glock memory shrinkerBenjamin Marzinski
It is possible for gfs2_shrink_glock_memory() to check a glock for demotion that's in the process of being freed by gfs2_glock_put(). In this case, gfs2_shrink_glock_memory() will acquire a new reference to this glock, and then try to free the glock itself when it drops the refernce. To solve this, gfs2_shrink_glock_memory() just needs to check if the glock is in the process of being freed, and if so skip it without ever unlocking the lru_lock. Signed-off-by: Benjamin Marzinski <bmarzins@redhat.com> Acked-by: Bob Peterson <rpeterso@redhat.com> Signed-off-by: Steven Whitehouse <swhiteho@redhat.com>
2009-07-30GFS2: keep statfs info in sync on growsBenjamin Marzinski
GFS2 wasn't syncing its statfs info on grows. This causes a problem when you grow the filesystem on multiple nodes. GFS2 would calculate the new space based on the resource groups (which are always current), and then assume that the filesystem had grown the from the existing statfs size. If you grew the filesystem on two different nodes in a short time, the second node wouldn't see the statfs size change from the first node, and would assume that it was grown by a larger amount than it was. When all these changes were synced out, the total fileystem size would be incorrect (the first grow would be counted twice). This patch syncs makes GFS2 read in the statfs changes from disk before a grow, and write them out after the grow, while the master statfs inode is locked. Signed-off-by: Benjamin Marzinski <bmarzins@redhat.com> Signed-off-by: Steven Whitehouse <swhiteho@redhat.com>
2009-07-30GFS2: Shrink the shrinkerSteven Whitehouse
This patch removes some of the special cases that the shrinker was trying to deal with. As a result we leave fewer items on the list and none at all which cannot be demoted. This makes the list scanning more efficient and solves some issues seen with large numbers of inodes. Signed-off-by: Steven Whitehouse <swhiteho@redhat.com>
2009-07-30ARM: 5597/1: [PCI] reset all internal hardware prior PCI initializationYegor Yefremov
Make software reset to avoid freeze if PCI bus was messed up Signed-off-by: Yegor Yefremov <yegorslists@googlemail.com> Acked-by: Andrew Victor <linux@maxim.org.za> Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
2009-07-30Merge branch 's3c-fixes-rc4' of git://aeryn.fluff.org.uk/bjdooks/linuxRussell King
2009-07-30Merge branch 'mxc-defconfig-updates' of ↵Russell King
git://git.pengutronix.de/git/imx/linux-2.6
2009-07-30Merge branch 'fix' of ↵Russell King
git://git.kernel.org/pub/scm/linux/kernel/git/ycmiao/pxa-linux-2.6
2009-07-30ARM: 5627/1: Fix restoring of lr at the end of mcountUwe Kleine-König
After ftrace_trace_function is called r1 is probably clobbered so don't try to use its value for restoring. This was introduced in v2.6.29~38^2~7 Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de> Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
2009-07-30ARM: 5624/1: Document cache aliasing regionLinus Walleij
Augment the memory.txt file for ARM to list the cache aliasing region ffff4000-fffffff. Signed-off-by: Linus Walleij <linus.walleij@stericsson.com> Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
2009-07-30lguest and virtio: cleanup struct definitions to Linux style.Rusty Russell
I've been doing this for years, and akpm picked me up on it about 12 months ago. lguest partly serves as example code, so let's do it Right. Also, remove two unused fields in struct vblk_info in the example launcher. Signed-off-by: Rusty Russell <rusty@rustcorp.com.au> Cc: Ingo Molnar <mingo@redhat.com>
2009-07-30lguest: update commentryRusty Russell
Every so often, after code shuffles, I need to go through and unbitrot the Lguest Journey (see drivers/lguest/README). Since we now use RCU in a simple form in one place I took the opportunity to expand that explanation. Signed-off-by: Rusty Russell <rusty@rustcorp.com.au> Cc: Ingo Molnar <mingo@redhat.com> Cc: Paul McKenney <paulmck@linux.vnet.ibm.com>
2009-07-30lguest: fix comment styleRusty Russell
I don't really notice it (except to begrudge the extra vertical space), but Ingo does. And he pointed out that one excuse of lguest is as a teaching tool, it should set a good example. Signed-off-by: Rusty Russell <rusty@rustcorp.com.au> Cc: Ingo Molnar <mingo@redhat.com>
2009-07-30virtio: refactor find_vqsMichael S. Tsirkin
This refactors find_vqs, making it more readable and robust, and fixing two regressions from 2.6.30: - double free_irq causing BUG_ON on device removal - probe failure when vq can't be assigned to msi-x vector (reported on old host kernels) Tested-by: Amit Shah <amit.shah@redhat.com> Signed-off-by: Michael S. Tsirkin <mst@redhat.com> Signed-off-by: Rusty Russell <rusty@rustcorp.com.au>
2009-07-30virtio: delete vq from listMichael S. Tsirkin
This makes delete vq the reverse of find vq. This is required to make it possible to retry find_vqs after a failure, otherwise the list gets corrupted. Signed-off-by: Michael S. Tsirkin <mst@redhat.com> Signed-off-by: Rusty Russell <rusty@rustcorp.com.au>
2009-07-30virtio: fix memory leak on device removalMichael S. Tsirkin
Make vp_free_vectors do the reverse of vq_request_vectors. Signed-off-by: Michael S. Tsirkin <mst@redhat.com> Signed-off-by: Rusty Russell <rusty@rustcorp.com.au>
2009-07-30lguest: fix descriptor corruption in example launcherRusty Russell
1d589bb16b825b3a7b4edd34d997f1f1f953033d "Add serial number support for virtio_blk, V4a" extended 'struct virtio_blk_config' to 536 bytes. Lguest and S/390 both use an 8 bit value for the feature length, and this change broke them (if the code is naive). Signed-off-by: Rusty Russell <rusty@rustcorp.com.au> Cc: John Cooper <john.cooper@redhat.com> Cc: Christian Borntraeger <borntraeger@de.ibm.com>
2009-07-30lguest: dereferencing freed mem in add_eventfd()Dan Carpenter
"new" was freed and then dereferenced. Also the return value wasn't being used so I modified the caller as well. Compile tested only. Found by smatch (http://repo.or.cz/w/smatch.git). regards, dan carpenter Signed-off-by: Dan Carpenter <error27@gmail.com> Signed-off-by: Rusty Russell <rusty@rustcorp.com.au>