| Age | Commit message (Collapse) | Author |
|---|
|
em28xx_pre_card_setup()
em28xx_pre_card_setup() is meant to contain board-specific initialization. Also,
as autodetection sometimes occur only after having i2c bus enabled, this
function may need to be called later.
Moving those setups to happen outside the function avoids calling it twice without
need and without duplicating output lines at dmesg.
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
|
|
We don't know the xtal frequency of Silvercrest, but we need to have
some value in order to allow controlling the frame rate frequency. The
value is probably still wrong, since the manufacturer announces this
device as being capable of 30fps, but the maximum we can get is
13.5 fps.
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
|
|
Due to historical reasons, em28xx driver gets two consecutive frames and
fold them into an unique framing, doing interlacing. While this works
fine for TV images, this produces two bad effects with webcams:
1) webcam images are progressive. Merging two consecutive images produce
interlacing artifacts on the image;
2) since the driver needs to get two frames, it reduces the maximum
frame rate by two.
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
|
|
As reported by hermann pitton <hermann-pitton@arcor.de>, some devices
has a different chip id for em2710 (likely the older ones):
em28xx: New device @ 480 Mbps (eb1a:2710, interface 0, class 0)
em28xx #0: Identified as EM2710/EM2750/EM2751 webcam grabber (card=22)
em28xx #0: em28xx chip ID = 17
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
|
|
Thanks to hermann pitton <hermann-pitton@arcor.de> for pointing this new
variation.
Tested-by: hermann pitton <hermann-pitton@arcor.de>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
|
|
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
|
|
em28xx doesn't have temporal scaling. However, on webcams, sensors are
capable of changing the output rate. So, VIDIOC_[G|S]_PARM ioctls should
be passed to the sensor for it to properly set frame rate.
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
|
|
Implement g_parm/s_parm ioctls. Those are used to check the current
frame rate (in fps) and to set it to a value. In practice, there are
only 15 possible different speeds, due to chip limits.
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
|
|
A user discovered that the Geniatech x8000 encountered a regression when
the xc3028 power management was introduced. The xc3028 never recovers after
setting the powerdown register, which is probably because the xc3028 reset
GPIO is not properly configured. Since I do not have access to the hardware
and thus cannot determine the correct GPIO configuration, just disable xc3028
power management on this board, which fixes the regression.
Thanks to user "ritec" for reporting the issue and testing the fix.
Cc: rictec <rictec@netcabo.pt>
Signed-off-by: Devin Heitmueller <dheitmueller@kernellabs.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
|
|
The introduction of the zl10353 i2c gate control broke support for the
Geniatech board (which is not behind an i2 gate). Add the needed parameter.
Signed-off-by: Devin Heitmueller <dheitmueller@kernellabs.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
|
|
WinTV-HVR1120 DVB-T/Hybrid
Signed-off-by: Michael Krufky <mkrufky@kernellabs.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
|
|
WinTV-HVR1150 ATSC/QAM-Hybrid
Signed-off-by: Michael Krufky <mkrufky@kernellabs.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
|
|
Remove the following build warning:
sms-cards.c: In function 'sms_board_event':
sms-cards.c:120: warning: unused variable 'board'
Thanks to Hans Verkuil for pointing this out.
The problem code has been #if 0'd for now, this will likely be
used again in the future, once the event interface is complete.
Cc: Hans Verkuil <hverkuil@xs4all.nl>
Signed-off-by: Michael Krufky <mkrufky@kernellabs.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
|
|
type" messages
The iSight sends non-UVC status events through the interrupt endpoint. Those
invalid events are reported to the kernel log, resulting in a log flood.
Only log the events when the UVC_TRACE_STATUS flag is set.
Signed-off-by: Laurent Pinchart <laurent.pinchart@skynet.be>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
|
|
ViMicro devices
Commit 50144aeeb702ea105697ae5249f059ea3990b838 broke the Samsung NC10
netbook webcam. Instead of applying the FIX_BANDWIDTH quirk to all ViMicro
devices, list the devices explicitly.
Signed-off-by: Laurent Pinchart <laurent.pinchart@skynet.be>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
|
|
The current GPIO configuration breaks all Hauppauge devices.
The code being removed affects Hauppauge devices only,
and is the cause of the breakage.
Signed-off-by: Michael Krufky <mkrufky@kernellabs.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
|
|
MAINTAINERS | 8 ++++++++
Signed-off-by: Brian Johnson <brijohn@gmail.com>
Acked-by: Jean-Francois Moine <moinejf@free.fr>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
|
|
Moving BOOT fixes problem.
Signed-off-by: Nils Kassube <kassube@gmx.net>
Acked-by: Antti Palosaari <crope@iki.fi>
Signed-off-by: Douglas Schilling Landgraf <dougsland@redhat.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
|
|
Currently, the VIDIOC_S_STD ioctl just returns -EINVAL regardless of
the norm passed. This patch sets cx23885_mpeg_template.tvnorms and
cx23885_mpeg_template.current_norm so that the VIDIOC_S_STD will work.
Thanks to Joseph Yasi for pointing this out, even though this particular
fix was already pushed into a development repository, merge priority of
this changeset has been escalated as a result of Joseph posting this
identical patch.
Signed-off-by: Michael Krufky <mkrufky@kernellabs.com>
Signed-off-by: Joseph A. Yasi <joe.yasi@gmail.com>
Reviewed-by: Steven Toth <stoth@kernellabs.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
|
|
back is reliable
Current tip is broken and does not switch back to DVB-T correctly
Signed-off-by: Sohail Syyed <linuxtv@hubstar.net>
Signed-off-by: Steven Toth <stoth@kernellabs.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
|
|
This device uses msp34xx and uses 2.048 MHz frequency for I2S
communication.
Thanks to Angelo Cano <acano@fastmail.fm> for pointing the issues with
this device and proposing an approach for fixing the issue.
Tested-by: Angelo Cano <acano@fastmail.fm>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
|
|
Fixes stack corruption bug present in dump_regs function of zl10353 and
qt1010 drivers: the buffer buf was one byte smaller than required -
there are 4 chars for address prefix, 16 * 3 chars for dump of 16 eeprom
bytes per line and 1 byte for zero ending the string required, i.e. 53
bytes, but only 52 were provided.
The one byte missing in stack based buffer buf can cause stack
corruption possibly leading to kernel oops, as discovered originally
with af9015 driver (af9015: fix stack corruption bug).
Signed-off-by: Jan Nikitenko <jan.nikitenko@gmail.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
|
|
Some mt9v011 webcams report 0x8332 chip version, instead of 0x8243. From
the revision history at the mt9v011 datasheet, it seems that the chip
version has changed from the first release of the chip.
Thanks-to hermann pitton <hermann-pitton@arcor.de> for pointing this to
me, on his tests with a Silvercrest webcam.
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
|
|
This mistakenly tested against sizeof(freqs) instead of the array size. Due to
the mask the only illegal value possible was 3.
Reported-by: Roel Kluin <roel.kluin@gmail.com>
Signed-off-by: Andy Walls <awalls@radix.net>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
|
|
This mistakenly tests against sizeof(freqs) instead of the array size. Due to
the mask the only illegal value possible was 3.
Signed-off-by: Roel Kluin <roel.kluin@gmail.com>
Signed-off-by: Andy Walls <awalls@radix.net>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
|
|
mclk_get_divisor uses pcdev->soc_host.dev, make sure it is initialized.
Signed-off-by: Antonio Ospite <ospite@studenti.unina.it>
Signed-off-by: Guennadi Liakhovetski <g.liakhovetski@gmx.de>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/tip/linux-2.6-tip
* 'perfcounters-fixes-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/linux-2.6-tip:
perf_counter: Report the cloning task as parent on perf_counter_fork()
perf_counter: Fix an ipi-deadlock
perf: Rework/fix the whole read vs group stuff
perf_counter: Fix swcounter context invariance
perf report: Don't show unresolved DSOs and symbols when -S/-d is used
perf tools: Add a general option to enable raw sample records
perf tools: Add a per tracepoint counter attribute to get raw sample
perf_counter: Provide hw_perf_counter_setup_online() APIs
perf list: Fix large list output by using the pager
perf_counter, x86: Fix/improve apic fallback
perf record: Add missing -C option support for specifying profile cpu
perf tools: Fix dso__new handle() to handle deleted DSOs
perf tools: Fix fallback to cplus_demangle() when bfd_demangle() is not available
perf report: Show the tid too in -D
perf record: Fix .tid and .pid fill-in when synthesizing events
perf_counter, x86: Fix generic cache events on P6-mobile CPUs
perf_counter, x86: Fix lapic printk message
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/tip/linux-2.6-tip
* 'core-fixes-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/linux-2.6-tip:
futex: Fix handling of bad requeue syscall pairing
futex: Fix compat_futex to be same as futex for REQUEUE_PI
locking, sched: Give waitqueue spinlocks their own lockdep classes
futex: Update futex_q lock_ptr on requeue proxy lock
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/tip/linux-2.6-tip
* 'x86-fixes-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/linux-2.6-tip:
x86: Fix oops in identify_cpu() on CPUs without CPUID
x86: Clear incorrectly forced X86_FEATURE_LAHF_LM flag
x86, mce: therm_throt - change when we print messages
x86: Add reboot quirk for every 5 series MacBook/Pro
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/jlbec/ocfs2
* 'upstream-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/jlbec/ocfs2: (22 commits)
ocfs2: Fix possible deadlock when extending quota file
ocfs2: keep index within status_map[]
ocfs2: Initialize the cluster we're writing to in a non-sparse extend
ocfs2: Remove redundant BUG_ON in __dlm_queue_ast()
ocfs2/quota: Release lock for error in ocfs2_quota_write.
ocfs2: Define credit counts for quota operations
ocfs2: Remove syncjiff field from quota info
ocfs2: Fix initialization of blockcheck stats
ocfs2: Zero out padding of on disk dquot structure
ocfs2: Initialize blocks allocated to local quota file
ocfs2: Mark buffer uptodate before calling ocfs2_journal_access_dq()
ocfs2: Make global quota files blocksize aligned
ocfs2: Use ocfs2_rec_clusters in ocfs2_adjust_adjacent_records.
ocfs2: Fix deadlock on umount
ocfs2: Add extra credits and access the modified bh in update_edge_lengths.
ocfs2: Fail ocfs2_get_block() immediately when a block needs allocation
ocfs2: Fix error return in ocfs2_write_cluster()
ocfs2: Fix compilation warning for fs/ocfs2/xattr.c
ocfs2: Initialize count in aio_write before generic_write_checks
ocfs2: log the actual return value of ocfs2_file_aio_write()
...
|
|
* 'for-linus' of git://neil.brown.name/md:
md: allow upper limit for resync/reshape to be set when array is read-only
md/raid5: Properly remove excess drives after shrinking a raid5/6
md/raid5: make sure a reshape restarts at the correct address.
md/raid5: allow new reshape modes to be restarted in the middle.
md: never advance 'events' counter by more than 1.
Remove deadlock potential in md_open
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/lethal/sh-2.6
* 'sh/for-2.6.31' of git://git.kernel.org/pub/scm/linux/kernel/git/lethal/sh-2.6:
sh: fix i2c init order on ap325rxa V2
sh: fix i2c init order on Migo-R V2
sh: convert processor device setup functions to arch_initcall()
|
|
kernel_sendpage() does the proper default case handling for when the
socket doesn't have a native sendpage implementation.
Now, arguably this might be something that we could instead solve by
just specifying that all protocols should do it themselves at the
protocol level, but we really only care about the common protocols.
Does anybody really care about sendpage on something like Appletalk? Not
likely.
Acked-by: David S. Miller <davem@davemloft.net>
Acked-by: Julien TINNES <julien@cr0.org>
Acked-by: Tavis Ormandy <taviso@sdf.lonestar.org>
Cc: stable@kernel.org
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
|
|
A bug in (9f498cc: perf_counter: Full task tracing) makes
profiling multi-threaded apps it go belly up.
[ output as: (PID:TID):(PPID:PTID) ]
# ./perf report -D | grep FORK
0x4b0 [0x18]: PERF_EVENT_FORK: (3237:3237):(3236:3236)
0xa10 [0x18]: PERF_EVENT_FORK: (3237:3238):(3236:3236)
0xa70 [0x18]: PERF_EVENT_FORK: (3237:3239):(3236:3236)
0xad0 [0x18]: PERF_EVENT_FORK: (3237:3240):(3236:3236)
0xb18 [0x18]: PERF_EVENT_FORK: (3237:3241):(3236:3236)
Shows us that the test (27d028d perf report: Update for the new
FORK/EXIT events) in builtin-report.c:
/*
* A thread clone will have the same PID for both
* parent and child.
*/
if (thread == parent)
return 0;
Will clearly fail.
The problem is that perf_counter_fork() reports the actual
parent, instead of the cloning thread.
Fixing that (with the below patch), yields:
# ./perf report -D | grep FORK
0x4c8 [0x18]: PERF_EVENT_FORK: (1590:1590):(1589:1589)
0xbd8 [0x18]: PERF_EVENT_FORK: (1590:1591):(1590:1590)
0xc80 [0x18]: PERF_EVENT_FORK: (1590:1592):(1590:1590)
0x3338 [0x18]: PERF_EVENT_FORK: (1590:1593):(1590:1590)
0x66b0 [0x18]: PERF_EVENT_FORK: (1590:1594):(1590:1590)
Which both makes more sense and doesn't confuse perf report
anymore.
Reported-by: Pekka Enberg <penberg@cs.helsinki.fi>
Signed-off-by: Peter Zijlstra <a.p.zijlstra@chello.nl>
Cc: Arnaldo Carvalho de Melo <acme@redhat.com>
Cc: paulus@samba.org
Cc: Anton Blanchard <anton@samba.org>
Cc: Arjan van de Ven <arjan@infradead.org>
LKML-Reference: <1250172882.5241.62.camel@twins>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
|
|
perf_pending_counter() is called from IRQ context and will call
perf_counter_disable(), however perf_counter_disable() uses
smp_call_function_single() which doesn't fancy being used with
IRQs disabled due to IPI deadlocks.
Fix this by making it use the local __perf_counter_disable()
call and teaching the counter_sched_out() code about pending
disables as well.
This should cover the case where a counter migrates before the
pending queue gets processed.
Signed-off-by: Peter Zijlstra <a.p.zijlstra@chello.nl>
Cc: Corey J Ashford <cjashfor@us.ibm.com>
Cc: Paul Mackerras <paulus@samba.org>
Cc: stephane eranian <eranian@googlemail.com>
LKML-Reference: <20090813103655.244097721@chello.nl>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
|
|
Replace PERF_SAMPLE_GROUP with PERF_SAMPLE_READ and introduce
PERF_FORMAT_GROUP to deal with group reads in a more generic
way.
This allows you to get group reads out of read() as well.
Signed-off-by: Peter Zijlstra <a.p.zijlstra@chello.nl>
Cc: Corey J Ashford <cjashfor@us.ibm.com>
Cc: Paul Mackerras <paulus@samba.org>
Cc: stephane eranian <eranian@googlemail.com>
LKML-Reference: <20090813103655.117411814@chello.nl>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
|
|
perf_swcounter_is_counting() uses a lock, which means we cannot
use swcounters from NMI or when holding that particular lock,
this is unintended.
The below removes the lock, this opens up race window, but not
worse than the swcounters already experience due to RCU
traversal of the context in perf_swcounter_ctx_event().
This also fixes the hard lockups while opening a lockdep
tracepoint counter.
Signed-off-by: Peter Zijlstra <a.p.zijlstra@chello.nl>
Acked-by: Frederic Weisbecker <fweisbec@gmail.com>
Cc: Paul Mackerras <paulus@samba.org>
Cc: stephane eranian <eranian@googlemail.com>
Cc: Corey J Ashford <cjashfor@us.ibm.com>
LKML-Reference: <1250149915.10001.66.camel@twins>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
|
|
We're interested in just those symbols/DSOs, so filter out the
unresolved ones.
Signed-off-by: Arnaldo Carvalho de Melo <acme@redhat.com>
Cc: Peter Zijlstra <peterz@infradead.org>
LKML-Reference: <20090812211957.GE3495@ghostprotocols.net>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
|
|
While we can enable the perf sample records per tracepoint
counter, we may also want to enable this option for every
tracepoint counters to open, so that we don't need to add a
:record flag for all of them.
Add the -R, --raw-samples options for this purpose.
Signed-off-by: Frederic Weisbecker <fweisbec@gmail.com>
Cc: Peter Zijlstra <peterz@infradead.org>
Cc: Arnaldo Carvalho de Melo <acme@redhat.com>
Cc: Mike Galbraith <efault@gmx.de>
LKML-Reference: <1250152039-7284-2-git-send-email-fweisbec@gmail.com>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
|
|
Add a new flag field while opening a tracepoint perf counter:
-e tracepoint_subsystem:tracepoint_name:flags
This is intended to be generic although for now it only supports the
r[e[c[o[r[d]]]]] flag:
./perf record -e workqueue:workqueue_insertion:record
./perf record -e workqueue:workqueue_insertion:r
will have the same effect: enabling the raw samples record for
the given tracepoint counter.
In the future, we may want to support further flags, separated
by commas.
Signed-off-by: Frederic Weisbecker <fweisbec@gmail.com>
Cc: Peter Zijlstra <peterz@infradead.org>
Cc: Arnaldo Carvalho de Melo <acme@redhat.com>
Cc: Mike Galbraith <efault@gmx.de>
LKML-Reference: <1250152039-7284-1-git-send-email-fweisbec@gmail.com>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
|
|
Provide weak aliases for hw_perf_counter_setup_online(). This is
used by the BTS patches (for v2.6.32), but it interacts with
fixes so propagate this upstream. (it has no effect as of yet)
Also export perf_counter_output() to architecture code.
Cc: Peter Zijlstra <a.p.zijlstra@chello.nl>
Cc: Paul Mackerras <paulus@samba.org>
Cc: Frederic Weisbecker <fweisbec@gmail.com>
LKML-Reference: <new-submission>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
|
|
When /sys/kernel/debug is mounted the list can be imense, so
use the pager like the other tools.
Signed-off-by: Arnaldo Carvalho de Melo <acme@redhat.com>
Acked-by: Frederic Weisbecker <fweisbec@gmail.com>
Cc: Peter Zijlstra <peterz@infradead.org>
LKML-Reference: <20090812174459.GB3495@ghostprotocols.net>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
|
|
Convert the AP325RXA board code to register devices at
arch_initcall() time instead of device_initcall(). This
fix unbreaks pcf8563 RTC driver support.
Signed-off-by: Magnus Damm <damm@igel.co.jp>
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
|
|
Convert the Migo-R board code to register devices at
arch_initcall() time instead of __initcall(). This fix
unbreaks migor_ts touch screen driver support.
Signed-off-by: Magnus Damm <damm@igel.co.jp>
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
|
|
Convert the processor platform device setup
functions from __initcall() and sometimes
device_initcall() to arch_initcall().
This makes sure that the platform devices are
registered a bit earlier so the devices are
available when drivers register using initcall
levels earlier than device_initcall().
A good example is platform devices needed by
i2c-sh_mobile.c which registers a bit earlier
using subsys_initcall().
Signed-off-by: Magnus Damm <damm@igel.co.jp>
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
|
|
Normally we only allow the upper limit for a reshape to be decreased
when the array not performing a sync/recovery/reshape, otherwise there
could be races. But if an array is part-way through a reshape when it
is assembled the reshape is started immediately leaving no window
to set an upper bound.
If the array is started read-only, the reshape will be suspended until
the array becomes writable, so that provides a window during which it
is perfectly safe to reduce the upper limit of a reshape.
So: allow the upper limit (sync_max) to be reduced even if the reshape
thread is running, as long as the array is still read-only.
Signed-off-by: NeilBrown <neilb@suse.de>
|
|
We were removing the drives, from the array, but not
removing symlinks from /sys/.... and not marking the device
as having been removed.
Signed-off-by: NeilBrown <neilb@suse.de>
|
|
This "if" don't allow for the possibility that the number of devices
doesn't change, and so sector_nr isn't set correctly in that case.
So change '>' to '>='.
Signed-off-by: NeilBrown <neilb@suse.de>
|
|
md/raid5 doesn't allow a reshape to restart if it involves writing
over the same part of disk that it would be reading from.
This happens at the beginning of a reshape that increases the number
of devices, at the end of a reshape that decreases the number of
devices, and continuously for a reshape that does not change the
number of devices.
The current code is correct for the "increase number of devices"
case as the critical section at the start is handled by userspace
performing a backup.
It does not work for reducing the number of devices, or the
no-change case.
For 'reducing', we need to invert the test. For no-change we cannot
really be sure things will be safe, so simply require the array
to be read-only, which is how the user-space code which carefully
starts such arrays works.
Signed-off-by: NeilBrown <neilb@suse.de>
|
|
When assembling arrays, md allows two devices to have different event
counts as long as the difference is only '1'. This is to cope with
a system failure between updating the metadata on two difference
devices.
However there are currently times when we update the event count by
2. This was done to keep the event count even when the array is clean
and odd when it is dirty, which allows us to avoid writing common
update to spare devices and so allow those spares to go to sleep.
This is bad for the above reason. So change it to never increase by
two. This means that the alignment between 'odd/even' and
'clean/dirty' might take a little longer to attain, but that is only a
small cost. The spares will get a few more updates but that will
still be spared (;-) most updates and can still go to sleep.
Prior to this patch there was a small chance that after a crash an
array would fail to assemble due to the overly large event count
mismatch.
Signed-off-by: NeilBrown <neilb@suse.de>
|
