| Age | Commit message (Collapse) | Author |
|---|
|
usb-storage: Workaround devices with bogus sense size
Some devices, such as Huawei E169, advertise more than the standard
amount of sense data, causing us to set US_FL_SANE_SENSE, assuming
they support it. However, they subsequently fail the request sense
with that size.
This works around it generically. When a sense request fails due to
a device returning an error, US_FL_SANE_SENSE was set, and that sense
request used a larger sense size, we retry with a smaller size before
giving up.
Based on an original patch by Ben Efros <ben@pc-doctor.com>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Acked-by: Alan Stern <stern@rowland.harvard.edu>
Cc: stable <stable@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
|
|
When the EHCI driver falls behind in its scheduling, the active stream's
first empty microframe may be in the past with respect to the current
microframe. The code attempts to move the starting microframe ("start") N
number of microframes forward, where N is the interval of endpoint.
However, stream->interval is a copy of the endpoint's bInterval, which is
designated in frames for FS devices, and microframes for HS devices.
Convert stream->interval to microframes before using it to move the
starting microframe forward.
Acked-by: Alan Stern <stern@rowland.harvard.edu>
Signed-off-by: Sarah Sharp <sarah.a.sharp@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
|
|
Here is a patch for Airplus MCD 650 card
Note: This device is with Victor V Kudlak, and he confirmed that this
device works with the patch.
Signed-off-by: Huzaifa Sidhpurwala <sidhpurwala.huzaifa@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
|
|
A halted qTD always triggers a hardware list update because the qset was
either removed or reactivated.
Signed-off-by: David Vrabel <david.vrabel@csr.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
|
|
If an endpoint is deleted before it's been fully added to the hardware
list, the associated qset will not be fully initialized and an oops will
occur when complete(&qset->remove_complete) is called. This can happen
if a queued URB is cancelled.
Fix this by only removing the qset from the hardware list if the
cancelled URB had qTDs.
Signed-off-by: David Vrabel <david.vrabel@csr.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
|
|
An urb's transfer buffer must be kmalloc'd memory and not point to the
stack or a DMA API warning results.
Signed-off-by: David Vrabel <david.vrabel@csr.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
|
|
The usb_host class is no more. Rename its documentation file (which
only contained WUSB specific files) to .../sysfs-class-uwb_rc-wusbhc.
Signed-off-by: David Vrabel <david.vrabel@csr.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
|
|
The linker scripts grew some use of weirdly wrong linker script syntax.
It happens to work, but it's not what the syntax is documented to be.
Clean it up to use the official syntax.
Signed-off-by: Roland McGrath <roland@redhat.com>
CC: Ian Lance Taylor <iant@google.com>
|
|
This fixes a panic which is triggered when the hardware "disappears" from
beneath the driver, i.e. when wireless is toggled off via Fn-F2 on various
EeePC models.
Ref. bug report http://bugzilla.kernel.org/show_bug.cgi?id=13390
panic http://bugzilla.kernel.org/attachment.cgi?id=21928
Signed-off-by: Darren Salt <linux@youmustbejoking.demon.co.uk>
Cc: stable <stable@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
|
|
This patch contains more sched.h additions for drivers that built
fine under x86_64 but not i386 for some reason.
Signed-off-by: Jeff Mahoney <jeffm@suse.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
|
|
Duh.. we need to preserve the wrap bit when adding.
Signed-off-by: Alan Cox <alan@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
|
|
add_10bit loses the existing wrap value
Signed-off-by: Alan Cox <alan@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
|
|
Commit d43c36dc removed sched.h from interrupt.h and distributed sched.h
to users which needed it. This finishes it up for staging.
Signed-off-by: Jeff Mahoney <jeffm@suse.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
|
|
commit d43c36dc removed sched.h from interrupt.h. This broke the
vme drivers. This patch fixes them.
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
|
|
commit d43c36dc removed sched.h from interrupt.h. This broke the
poch driver. This patch fixes this.
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
|
|
commit d43c36dc removed sched.h from interrupt.h. This broke the
b3dfg driver. This patch fixes this.
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
|
|
commit d43c36dc removed sched.h from interrupt.h. This broke some of
the comedi drivers. This patch fixes this.
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
|
|
linux/sched.h include was removed form linux/poll.h by
commmit a99bbaf5ee6bad1aca0c88ea65ec6e5373e86184
Required for definition of TASK_INTERRUPTIBLE amongst others
From: Jonathan Cameron <jic23@cam.ac.uk>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
|
|
If userspace tries to perform a requeue_pi on a non-requeue_pi waiter,
it will find the futex_q->requeue_pi_key to be NULL and OOPS.
Check for NULL in match_futex() instead of doing explicit NULL pointer
checks on all call sites. While match_futex(NULL, NULL) returning
false is a little odd, it's still correct as we expect valid key
references.
Signed-off-by: Darren Hart <dvhltc@us.ibm.com>
Cc: Peter Zijlstra <peterz@infradead.org>
Cc: Ingo Molnar <mingo@elte.hu>
CC: Eric Dumazet <eric.dumazet@gmail.com>
CC: Dinakar Guniguntala <dino@in.ibm.com>
CC: John Stultz <johnstul@us.ibm.com>
Cc: stable@kernel.org
LKML-Reference: <4AD60687.10306@us.ibm.com>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
|
|
The Unit_Characteristics entry of an SBP-2 unit directory is not
mandatory as far as I can tell. If it is missing, we would probably
fail to log in into the target because firewire-sbp2 would not wait for
status after it sent the login request.
The fix moves the cleanup of tgt->mgt_orb_timeout into a place where it
is executed exactly once before login, rather than 0..n times depending
on the target's config ROM. With targets with one or more
Unit_Characteristics entries, the result is the same as before.
Signed-off-by: Stefan Richter <stefanr@s5r6.in-berlin.de>
|
|
Add MT26438 (ConnectX EN 40GigE PCIe 2.0 5GT/s) to the list of supported
devices.
Signed-off-by: Eli Cohen <eli@mellanox.co.il>
Signed-off-by: Roland Dreier <rolandd@cisco.com>
|
|
This small typo written by author causes that McBSP receiver is disabled on
OMAP2430 and OMAP3430 even if only transmitter is stopped. This was noted
with ALSA SoC where simultaneous recording halted if playback was stopped
first.
Signed-off-by: Jarkko Nikula <jhnikula@gmail.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
|
|
This patch initializes the correct SDRC settings required
for DVFS on Zoom2.
Signed-off-by: Teerth Reddy <teerth@ti.com>
Signed-off-by: Kevin Hilman <khilman@deeprootsystems.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
|
|
The I2C-1 bus frequency on RX-51 should be 2.2 MHz. The speed is limited
by TWL5030/GAIA; a higher speed could lead to errors on the interface. The
maximum speed depends on the system clock for GAIA: 2.2 MHz (if 19.2 MHz),
2.4 MHz (26 MHz) or 2.9 MHz (38.4 MHz).
Signed-off-by: Aaro Koskinen <aaro.koskinen@nokia.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
|
|
Argument tparams was not being used to program
global register GCR.HI_THREAD_RESERVED. This patch fixes the same.
Signed-off-by: Anuj Aggarwal <anuj.aggarwal@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
|
|
The symbol CONFIG_ISP1301_OMAP was defined twice in the
defconfig. This was causing the warning:
arch/arm/configs/omap3_beagle_defconfig:972:warning:
override: reassigning to symbol ISP1301_OMAP
Signed-off-by: Sanjeev Premi <premi@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
|
|
The ALC662/663 parser calls wrongly alc880_auto_create_input_ctls()
to check the capture source selections. This should be alc882, instead.
Reference: Novell bnc#546918
http://bugzilla.novell.com/show_bug.cgi?id=546918
Signed-off-by: Takashi Iwai <tiwai@suse.de>
|
|
This way all flush_to_ldisc work is always done through the workqueues,
and we thus have a single point of serialization.
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
|
|
It basically turns a delayed work into an immediate work, and then waits
for it to finish.
|
|
|
|
We have an optimization in btrfs to allow blocks to be
immediately freed if they were allocated in this transaction and never
written. Otherwise they are pinned and freed when the transaction
commits.
This isn't optimal for discard mode because immediately freeing
them means immediately discarding them. It is better to give the
block to the pinning code and letting the (slow) discard happen later.
Signed-off-by: Chris Mason <chris.mason@oracle.com>
|
|
The discard support code in btrfs currently is guarded by ifdefs for
BIO_RW_DISCARD, which is never defines as it's the name of an enum
memeber. Just remove the useless ifdefs to actually enable the code.
Signed-off-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: Chris Mason <chris.mason@oracle.com>
|
|
Enable discard by default is not a good idea given the the trim speed
of SSD prototypes we've seen, and the carecteristics for many high-end
arrays. Turn of discards by default and require the -o discard option
to enable them on.
Signed-off-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: Chris Mason <chris.mason@oracle.com>
|
|
A recently fsync optimization make btrfs_sync_log skip calling
wait_for_writer in the single log writer case. This is incorrect
since the writer count can also be increased by btrfs_pin_log.
Signed-off-by: Yan Zheng <zheng.yan@oracle.com>
Signed-off-by: Chris Mason <chris.mason@oracle.com>
|
|
There's a problem where we don't do any space reservation for truncates, which
can cause you to OOPs because you will be allowed to go off in the weeds a bit
since we don't account for the delalloc bytes that are created as a result of
the truncate.
Signed-off-by: Josef Bacik <jbacik@redhat.com>
Signed-off-by: Chris Mason <chris.mason@oracle.com>
|
|
Yanmin reported a hackbench regression due to:
> commit de69a80be32445b0a71e8e3b757e584d7beb90f7
> Author: Peter Zijlstra <a.p.zijlstra@chello.nl>
> Date: Thu Sep 17 09:01:20 2009 +0200
>
> sched: Stop buddies from hogging the system
I really liked de69a80b, and it affecting hackbench shows I wasn't
crazy ;-)
So hackbench is a multi-cast, with one sender spraying multiple
receivers, who in their turn don't spray back.
This would be exactly the scenario that patch 'cures'. Previously
we would not clear the last buddy after running the next task,
allowing the sender to get back to work sooner than it otherwise
ought to have been, increasing latencies for other tasks.
Now, since those receivers don't poke back, they don't enforce the
buddy relation, which means there's nothing to re-elect the sender.
Cure this by less agressively clearing the buddy stats. Only clear
buddies when they were not chosen. It should still avoid a buddy
sticking around long after its served its time.
Reported-by: "Zhang, Yanmin" <yanmin_zhang@linux.intel.com>
Signed-off-by: Peter Zijlstra <a.p.zijlstra@chello.nl>
CC: Mike Galbraith <efault@gmx.de>
LKML-Reference: <1255084986.8802.46.camel@laptop>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
|
|
Yanmin reported that both tbench and hackbench were significantly
hurt by trying to keep tasks local on these domains, esp on small
cache machines.
So disable it in order to promote spreading outside of the cache
domains.
Reported-by: "Zhang, Yanmin" <yanmin_zhang@linux.intel.com>
Signed-off-by: Peter Zijlstra <a.p.zijlstra@chello.nl>
CC: Mike Galbraith <efault@gmx.de>
LKML-Reference: <1255083400.8802.15.camel@laptop>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
|
|
In 'cdd6c482c9ff9c55475ee7392ec8f672eddb7be6', we renamed
Performance Counters -> Performance Events.
The name showed up in /proc/interrupts also needs a change. I use
PMI (Performance monitoring interrupt) here, since it is the
official name used in Intel's documents.
Signed-off-by: Li Hong <lihong.hi@gmail.com>
Cc: Andrew Morton <akpm@linux-foundation.org>
Cc: Peter Zijlstra <a.p.zijlstra@chello.nl>
Cc: Paul Mackerras <paulus@samba.org>
LKML-Reference: <20091014105039.GA22670@uhli>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
|
|
Fix this build error:
next-20091013 randconfig build on s390x build breaks with
drivers/s390/built-in.o:(.data+0x3354): undefined reference to `sclp_vt220_pm_event_fn'
Reported-by: Kamalesh Babulal <kamalesh@linux.vnet.ibm.com>
Signed-off-by: Michael Holzheu <michael.holzheu@linux.vnet.ibm.com>
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
|
|
Use cio_is_console() in io_subchannel_probe to indicate that the
special handling is console specific. As long as there is no other
subchannel for which this might be true, it is misleading to speak
of "early devices". Should more of these devices be introduced,
a cleanup of all console special handling is in order anyway.
Signed-off-by: Peter Oberparleiter <peter.oberparleiter@de.ibm.com>
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
|
|
8d65af78 "sysctl: remove "struct file *" argument of ->proc_handler"
removed the struct file argument from all proc_handlers but didn't
change the call home proc handler (or call home was merged later).
So fix this now.
Cc: Alexey Dobriyan <adobriyan@gmail.com>
Cc: Hans-Joachim Picht <hans@de.ibm.com>
Signed-off-by: Heiko Carstens <heiko.carstens@de.ibm.com>
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
|
|
If the rdc_buffer is above 2G we need indirect addresssing so we have
to use an idaw to give the rdc_buffer to the ccw.
If the rdc_buffer is under 2G nothing changes.
Signed-off-by: Stefan Haberland <stefan.haberland@de.ibm.com>
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
|
|
This patch makes the hwcap bit for the high gprs feature to be visible
in /proc/cpuinfo.
Signed-off-by: Andreas Krebbel <Andreas.Krebbel@de.ibm.com>
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
|
|
Replace spin_lock with spin_lock_irqsave in dasd_eckd_restore_device.
Signed-off-by: Stefan Haberland <stefan.haberland@de.ibm.com>
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
|
|
When setting a channel attached tape online under Linux 2.6.31, the
"vol_id" process from udev hangs in sync_page():
2 sync_page+144 [0x1dfaac]
3 __wait_on_bit_lock+194 [0x58c23e]
4 __lock_page+116 [0x1df9dc]
5 truncate_inode_pages_range+728 [0x1ed7cc]
6 __blkdev_put+244 [0x25f738]
7 __fput+300 [0x229c4c]
8 filp_close+122 [0x225a3a]
The reason for that is an error in the request queue handling. It can
happen that we fetch a request, but do not process it further because
the number of queued requests exceeds TAPEBLOCK_MIN_REQUEUE.
To fix this, we should call blk_peek_request() instead of
blk_fetch_request() in the while condition and fetch the request in
the loop body afterwards.
This bug was introduced with the patch "block: implement and enforce
request peek/start/fetch" (9934c8c04561413609d2bc38c6b9f268cba774a4)
Signed-off-by: Michael Holzheu <holzheu@linux.vnet.ibm.com>
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
|
|
Hypfs never worked on systems that only provide D204 subcode 6.
In these cases we nevertheless used subcode 7. With this fix, we
use subcode 6, if it is available and the system does not provide
subcode 7.
Signed-off-by: Michael Holzheu <holzheu@linux.vnet.ibm.com>
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
|
|
Fix a build error due to a typo (missing comma) in:
ARM: 5754/1: ep93xx: update i2c support
Signed-off-by: H Hartley Sweeten <hsweeten@visionengravers.com>
Acked-by: Ryan Mallon <ryan@bluewatersys.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
|
|
Defines ELF_CORE_COPY_TASK_REGS so that CPU register information
of every thread is included in coredump. Without this, only the faulting
thread is coredumped.
Cc: Roger Quadros <ext-roger.quadros@nokia.com>
Cc: linux-arm-kernel@lists.infradead.org
Signed-off-by: Mika Westerberg <mika.westerberg@iki.fi>
Signed-off-by: Artem Bityutskiy <Artem.Bityutskiy@nokia.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
|
|
The 32-bit wide variant of "mov pc, reg" in Thumb-2 is unpredictable
causing improper handling of the undefined instructions not caught by
the kernel. This patch adds a movw_pc macro for such situations
(currently only used in call_fpe).
Signed-off-by: Catalin Marinas <catalin.marinas@arm.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
|
|
After sucessfully registering the misc device the driver iounmaps the
hardware registers and kfree's the device data structure. Ouch !
This was introduced with commit e42311d75 (riowatchdog: Convert to
pure OF driver) and went unnoticed for more than a year :)
Return success instead of dropping into the error cleanup code path.
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
