summaryrefslogtreecommitdiffstats
AgeCommit message (Collapse)Author
2012-01-04mac80211: remove dead codeMohammed Shafi Shajakhan
ieee80211_offchannel_enable_all_ps function is no longer used and looks like its logic is extensively handled in ieee80211_offchannel_stop_vifs Signed-off-by: Mohammed Shafi Shajakhan <mohammed@qca.qualcomm.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
2012-01-04mwl8k: Recover from firmware crashYogesh Ashok Powar
In case of firmware crash, reload the firmware and reconfigure it by triggering ieee80211_hw_restart; mac80211 utility function. V2 Addressed following comments from Lennert: - Stop the queues during reload - Removed atomic_t declaration for hw_restart - Extend the firmware reload support for sta firmware as well - Other misc changes Signed-off-by: Nishant Sarmukadam <nishants@marvell.com> Signed-off-by: Yogesh Ashok Powar <yogeshp@marvell.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
2012-01-04mac80211: Call driver commands after drv_start in mac80211 restart codeYogesh Ashok Powar
Ideally, hardware/firmware initialization is complete after the drv_start routine. In mac80211 restart code (ieee80211_reconfig), defer calling the driver commands i.e. setup fragmentation threshold, rts threshold and coverage class till drv_start routine is called. Signed-off-by: Nishant Sarmukadam <nishants@marvell.com> Signed-off-by: Yogesh Ashok Powar <yogeshp@marvell.com> v2: Removed extra blank line added. Signed-off-by: John W. Linville <linville@tuxdriver.com>
2012-01-04ath9k: tx queue enable is read only for EDMA chipsetsMohammed Shafi Shajakhan
for EDMA chip AR_Q_TXE (tx enable for each queue) is read only Signed-off-by: Mohammed Shafi Shajakhan <mohammed@qca.qualcomm.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
2012-01-04rt2x00: Change RF3853 to RF3053.Gertjan van Wingerde
According to the latest Ralink vendor drivers, this seems to be the real RF chipset type. Signed-off-by: Gertjan van Wingerde <gwingerde@gmail.com> Acked-by: Ivo van Doorn <IvDoorn@gmail.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
2012-01-04rt2x00: RT3593 is also applicable to USB.Gertjan van Wingerde
Signed-off-by: Gertjan van Wingerde <gwingerde@gmail.com> Acked-by: Ivo van Doorn <IvDoorn@gmail.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
2012-01-04rt2x00usb: Zero USB padding before sending URBJakub Kiciński
When USB driver requires padding at the end of frame or URB it will report this need by increasing return value of get_tx_data_len callback. Common USB code uses that return value as desired URB length. Ensure that appropriate part of skb's tailroom exists and is zeroed. Signed-off-by: Jakub Kicinski <kubakici@wp.pl> Acked-by: Ivo van Doorn <IvDoorn@gmail.com> -- drivers/net/wireless/rt2x00/rt2x00usb.c | 16 +++++++++++++--- 1 files changed, 13 insertions(+), 3 deletions(-) Signed-off-by: Gertjan van Wingerde <gwingerde@gmail.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
2012-01-04rt2800usb: Let rt2x00usb handle USB paddingJakub Kiciński
Older USB drivers does not append end padding to skb but instead report it in size of data to be transmitted to HW. rt2800usb should follow that behaviour. Custom write_tx_data callback which was adding pad to skb is not be needed any more. Thanks to this patch frames handed back from rt2800usb to mac80211 will no longer contain end padding. Signed-off-by: Jakub Kicinski <kubakici@wp.pl> Signed-off-by: Gertjan van Wingerde <gwingerde@gmail.com> Acked-by: Ivo van Doorn <IvDoorn@gmail.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
2012-01-04rt2x00: Convert big if-statements to switch-statements.Gertjan van Wingerde
Signed-off-by: Gertjan van Wingerde <gwingerde@gmail.com> Acked-by: Ivo van Doorn <IvDoorn@gmail.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
2012-01-04rt2x00: Whitespace cleanup.Gertjan van Wingerde
Signed-off-by: Gertjan van Wingerde <gwingerde@gmail.com> Acked-by: Ivo van Doorn <IvDoorn@gmail.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
2012-01-04rt2x00: Identify rt2800usb chipsets.Gertjan van Wingerde
According to the latest USB ID database these are all RT2770 / RT2870 / RT307x devices. Signed-off-by: Gertjan van Wingerde <gwingerde@gmail.com> Acked-by: Ivo van Doorn <IvDoorn@gmail.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
2012-01-04carl9170: move checksum and txseq into subfunctionsChristian Lamparter
Signed-off-by: Christian Lamparter <chunkeey@googlemail.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
2012-01-04rt2800usb: Move ID out of unknownLarry Finger
Testing on the openSUSE wireless forum has shown that a Linksys WUSB54GC v3 with USB ID 1737:0077 works with rt2800usb when the ID is written to /sys/.../new_id. This ID can therefore be moved out of UNKNOWN. Signed-off-by: Larry Finger <Larry.Finger@lwfinger.net> Cc: Stable <stable@vger.kernel.org> Acked-by: Gertjan van Wingerde <gwingerde@gmail.com> Acked-by: Ivo van Doorn <IvDoorn@gmail.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
2012-01-04mac80211: use RCU read locks for sta_info_getMohammed Shafi Shajakhan
this is being recently introduced by the commit a85e1d55974646a442d95911e3f7d7a891ea9ac5 Cc: Paul Stewart <pstew@google.com> Signed-off-by: Mohammed Shafi Shajakhan <mohammed@qca.qualcomm.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
2012-01-04ipw2x00: remove reset_port functionalityStanislav Yakovlev
Removes reset_port since it isn't used anywhere as suggested by Johannes Berg. Signed-off-by: Stanislav Yakovlev <stas.yakovlev@gmail.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
2012-01-04mac80211: fix kernel panic in IBSS due to a regressionMohammed Shafi Shajakhan
kernel panic occurs when we create an IBSS mode and leave it for sometime without any joiner and this is introduced by the commit ec2b774e7c91094d8c00de579646f1162b87b01e where we don't put proper braces for 'list_for_each_entry_safe' and we pass an invalid 'sta' pointer to __sta_info_destroy EIP is at __list_add+0xe/0xa0 EAX: f3b63db4 EBX: 00000000 ECX: eab88c1c EDX: 00000000 ESI: 00000000 EDI: 00000246 EBP: f3b63d80 ESP: f3b63d58 DS: 007b ES: 007b FS: 00d8 GS: 00e0 SS: 0068 Process kworker/u:2 (pid: 198, ti=f3b62000 task=f3afbea0 task.ti=f3b62000) Stack: 00000000 00000000 f9ef9821 00000000 00000000 eab88c30 f3b63d80 c017f623 eab88bf0 eab88bf0 f3b63dd0 c066f925 00000000 00000002 00000000 f9ef9821 f3b63da0 c0180a2b eab88c1c eab88c30 00000002 f3afbea0 eab88bf4 f3b63db4 Call Trace: [<f9ef9821>] ? __ieee80211_stop_tx_ba_session+0x31/0x60 [mac80211] [<c017f623>] ? debug_mutex_add_waiter+0x23/0x60 [<c066f925>] __mutex_lock_common+0xd5/0x390 [<f9ef9821>] ? __ieee80211_stop_tx_ba_session+0x31/0x60 [mac80211] [<c0180a2b>] ? trace_hardirqs_off+0xb/0x10 [<c066fd37>] mutex_lock_nested+0x47/0x60 [<f9ef9821>] ? __ieee80211_stop_tx_ba_session+0x31/0x60 [mac80211] [<f9ef9821>] __ieee80211_stop_tx_ba_session+0x31/0x60 [mac80211] [<f9ef8989>] ieee80211_sta_tear_down_BA_sessions+0x39/0x60 [mac80211] [<f9ef1a67>] __sta_info_destroy+0x57/0x780 [mac80211] [<f9ef2223>] ieee80211_sta_expire+0x93/0xb0 [mac80211] [<f9efc8f6>] ieee80211_ibss_work+0x2d6/0x530 [mac80211] Cc: Marek Lindner <lindner_marek@yahoo.de> Signed-off-by: Mohammed Shafi Shajakhan <mohammed@qca.qualcomm.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
2012-01-04mac80211: fix scan state machineMohammed Shafi Shajakhan
when we run high bandwidth UDP traffic and we trigger a scan, the scan state machine seems to be looping in SUSPEND->RESUME->DECISION->SUSPEND and SET_CHANNEL seems to be never called as 'tx_empty' is never true while running UDP traffic. fix this by settting SET_CHANNEL state when we get into RESUME state. Cc: Leela Kella <leela@qca.qualcomm.com> Signed-off-by: Mohammed Shafi Shajakhan <mohammed@qca.qualcomm.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
2012-01-04net/rfkill/rfkill-gpio.c: introduce missing kfreeJulia Lawall
Error handling code following a kmalloc should free the allocated data. The label fail_alloc already does this for rfkill. A simplified version of the semantic match that finds the problem is as follows: (http://coccinelle.lip6.fr) // <smpl> @r exists@ local idexpression x; statement S; identifier f1; position p1,p2; expression *ptr != NULL; @@ x@p1 = \(kmalloc\|kzalloc\|kcalloc\)(...); ... if (x == NULL) S <... when != x when != if (...) { <+...x...+> } x->f1 ...> ( return \(0\|<+...x...+>\|ptr\); | return@p2 ...; ) @script:python@ p1 << r.p1; p2 << r.p2; @@ print "* file: %s kmalloc %s return %s" % (p1[0].file,p1[0].line,p2[0].line) // </smpl> Signed-off-by: Julia Lawall <julia@diku.dk> Signed-off-by: John W. Linville <linville@tuxdriver.com>
2012-01-04ath9k_hw: increase tx status ring buffer sizeRajkumar Manoharan
AR9003 chips read tx status from ring buffer whose max number of status descriptor is mininal compared to max number of tx buffers. On a stress condition, it can be easily overflown which might cause false tx hung detection. Though increasing number of max status descriptors consumes more memory, it helps to avoid false positive chip resets. Cc: Paul Stewart <pstew@google.com> Signed-off-by: Rajkumar Manoharan <rmanohar@qca.qualcomm.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
2012-01-04iwlegacy: 3945: fix hw passive scan on radar channelsStanislaw Gruszka
Patch fix firmware error on "iw dev wlan0 scan passive" for hardware scanning (with disable_hw_scan=0 module parameter). iwl3945 0000:03:00.0: Microcode SW error detected. Restarting 0x82000008. iwl3945 0000:03:00.0: Loaded firmware version: 15.32.2.9 iwl3945 0000:03:00.0: Start IWL Error Log Dump: iwl3945 0000:03:00.0: Status: 0x0002A2E4, count: 1 iwl3945 0000:03:00.0: Desc Time asrtPC blink2 ilink1 nmiPC Line iwl3945 0000:03:00.0: SYSASSERT (0x5) 0041263900 0x13756 0x0031C 0x00000 764 iwl3945 0000:03:00.0: Error Reply type 0x000002FC cmd C_SCAN (0x80) seq 0x443E ser 0x00340000 iwl3945 0000:03:00.0: Command C_SCAN failed: FW Error iwl3945 0000:03:00.0: Can't stop Rx DMA. We have disable ability to change passive scanning to active on particular channel when traffic is detected on that channel. Otherwise firmware will report error, when we try to do passive scan on radar channels. Reported-and-debugged-by: Pedro Francisco <pedrogfrancisco@gmail.com> Signed-off-by: Stanislaw Gruszka <sgruszka@redhat.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
2012-01-04iwlegacy: 3945: simplify calculations of retry limitStanislaw Gruszka
Signed-off-by: Stanislaw Gruszka <sgruszka@redhat.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
2012-01-04iwlegacy: random 3945-rs.c cleanupsStanislaw Gruszka
Signed-off-by: Stanislaw Gruszka <sgruszka@redhat.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
2012-01-04iwlegacy: 4965: remove one il4965_hdl_beaconStanislaw Gruszka
We have two such functions. Signed-off-by: Stanislaw Gruszka <sgruszka@redhat.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
2012-01-04iwlegacy: 3945: get rid of hw_{set,get}_rateStanislaw Gruszka
Remove these helpers, some are not unused at all, one can be unrolled in place of use. Signed-off-by: Stanislaw Gruszka <sgruszka@redhat.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
2012-01-04iwlegacy: 4965: small tx_cmd build cleanupStanislaw Gruszka
Get rid of two inline functions related and simplify a bit rts_retry_limit calculations. Signed-off-by: Stanislaw Gruszka <sgruszka@redhat.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
2012-01-04iwlegacy: 4965: toggle tx antenna inlineStanislaw Gruszka
Make function static and change antenna number inline. Signed-off-by: Stanislaw Gruszka <sgruszka@redhat.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
2012-01-04iwlegacy: move some i/o helpers out of inlineStanislaw Gruszka
This save us about 20k of text size, and should have no impact on performance as hot paths do not use much I/O. Before: text data bss dec hex filename 108512 1784 168 110464 1af80 drivers/net/wireless/iwlegacy/iwl3945.ko 165730 2164 156 168050 29072 drivers/net/wireless/iwlegacy/iwl4965.ko 91942 328 48 92318 1689e drivers/net/wireless/iwlegacy/iwlegacy.ko After: text data bss dec hex filename 95556 1784 168 97508 17ce4 drivers/net/wireless/iwlegacy/iwl3945.ko 154853 2164 156 157173 265f5 drivers/net/wireless/iwlegacy/iwl4965.ko 91634 328 48 92010 1676a drivers/net/wireless/iwlegacy/iwlegacy.ko Signed-off-by: Stanislaw Gruszka <sgruszka@redhat.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
2012-01-04iwlegacy: off by one in iwl3945_hw_build_tx_cmd_rate()Dan Carpenter
We use "rate_index" like this: rate = iwl3945_rates[rate_index].plcp; The iwl3945_rates[] array has IWL_RATE_COUNT_3945 elements so the limit here is off by one. Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com> Signed-off-by: Stanislaw Gruszka <sgruszka@redhat.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
2012-01-04iwlegacy: remove iwl-sta.cStanislaw Gruszka
I forgot to remove this file before. Signed-off-by: Stanislaw Gruszka <sgruszka@redhat.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
2012-01-04mac80211: always clear SDATA_STATE_OFFCHANNEL flagEliad Peller
If the vif is stopped while it is offchannel (e.g. right after p2p negotiation) the SDATA_STATE_OFFCHANNEL flag is never get cleared, resulting in various bad effects (e.g. GO can't start beaconing). Fix it by clearing the SDATA_STATE_OFFCHANNEL flag even if the vif is stopped. Signed-off-by: Eliad Peller <eliad@wizery.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
2012-01-04wireless: Treat IPv6 diffserv the same as IPv4 for 802.11eDave Täht
Wireless will select a different hardware queue based on the top 3 bits of the diffserv field, for ipv4. Extend that queue selection mechanism to ipv6, and make the calls orthogonal. Signed-off-by: Dave Täht <dave.taht@bufferbloat.net> Signed-off-by: John W. Linville <linville@tuxdriver.com>
2012-01-04NFC: Export a new attribute nfcid1 in target infoIlan Elias
The nfcid1 is the NFC-A identifier. It is exported as an attribute of the target info (returned as a response to NFC_CMD_GET_TARGET). Signed-off-by: Ilan Elias <ilane@ti.com> Acked-by: Samuel Ortiz <sameo@linux.intel.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
2012-01-04rt2x00: Mark active channel's survey data as "in use"Helmut Schaa
This is just a cosmetical fix since we only return survey data for the active channel but it allows iw to show that the survey data is for the currently used channel. Signed-off-by: Helmut Schaa <helmut.schaa@googlemail.com> Acked-by: Ivo van Doorn <IvDoorn@gmail.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
2012-01-04b43legacy: Avoid packet losses in the dma worker codeLarry Finger
This patch addresses a bug in the dma worker code that keeps draining packets even when the hardware queues are full. In such cases packets can not be passed down to the device and are erroneusly dropped by the code. It is based on commit bad6919469662b7c92bc6353642aaaa777b36bac, which fixes the same problem in b43. Signed-off-by: Larry Finger <Larry.Finger@lwfinger.net> Signed-off-by: John W. Linville <linville@tuxdriver.com>
2012-01-04b43: N-PHY: fix typo in TX power fixRafał Miłecki
Signed-off-by: Rafał Miłecki <zajec5@gmail.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
2012-01-04b43: N-PHY: fix controling RF overrideRafał Miłecki
Signed-off-by: Rafał Miłecki <zajec5@gmail.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
2012-01-04b43: N-PHY: update gain ctl workaroundsRafał Miłecki
Specs were updated, now we match wl according to MMIO dumps. Signed-off-by: Rafał Miłecki <zajec5@gmail.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
2012-01-04b43: add lacking boardflags definesRafał Miłecki
Signed-off-by: Rafał Miłecki <zajec5@gmail.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
2012-01-04ath9k: make ath_mci_duty_cycle staticLuis R. Rodriguez
This fixes this sparse warning: CHECK drivers/net/wireless/ath/ath9k/mci.c drivers/net/wireless/ath/ath9k/mci.c:23:4: warning: symbol 'ath_mci_duty_cycle' was not declared. Should it be static? Signed-off-by: Luis R. Rodriguez <mcgrof@qca.qualcomm.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
2012-01-04drivers/iwlwifi: use dma_zalloc_coherent() for DMA allocationDjalal Harouni
Replace dma_alloc_coherent()+memset() with the new dma_zalloc_coherent() Signed-off-by: Djalal Harouni <tixxdz@opendz.org> Signed-off-by: John W. Linville <linville@tuxdriver.com>
2012-01-04b43: N-PHY: get idle TSSI valuesRafał Miłecki
Signed-off-by: Rafał Miłecki <zajec5@gmail.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
2012-01-04b43: N-PHY: fix success condition of running samplesRafał Miłecki
Signed-off-by: Rafał Miłecki <zajec5@gmail.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
2012-01-04b43: N-PHY: move common TX/RX functionsRafał Miłecki
Signed-off-by: Rafał Miłecki <zajec5@gmail.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
2012-01-04cfg80211: relicense reg.c reg.h and genregdb.awk to ISCLuis R. Rodriguez
Following the tradition we have had with ath5k, ath9k, CRDA, wireless-regdb I'd like to license this code under the permissive ISC license for the code sharing purposes with other OSes, it'd sure be nice to help the landscape in this area. Although I am %82.89 owner of the regulatory code I have asked every contributor to the regulatory code and have receieved positive Acked-bys from everyone except two deceased entities: o Frans Pop RIP 2010 [0] - Frans Pop <elendil@planet.nl> - Frans Pop <fjp@debian.org> o Nokia RIP February, 11, 2011 [1], [2] - ext-yuri.ershov@nokia.com - kalle.valo@nokia.com Frans Pop's contribution was a simple patch 55f98938, titled, "wireless: remove trailing space in messages" which just add a \n to some printk lines. I'm going to treat these additions as uncopyrightable. As for the contributions made by employees on behalf of Nokia my contact point was Petri Karhula <petri.karhula@nokia.com> but after one month he noted he had not been able to get traction from the legal department on this request, as such it I proceeded by replacing their contributions in previous patches. The end goal is to help a clean rewrite that starts in userspace that is shared under ISC license which currently is taking place with the regulatory simulator [3]. [0] http://lists.debian.org/debian-devel/2011/12/msg00263.html [1] http://press.nokia.com/2011/02/11/nokia-outlines-new-strategy-introduces-new-leadership-operational-structure/ [2] http://NokiaPlanB.com [3] git://github.com/mcgrof/regsim.git Acked-by: Thadeu Lima de Souza Cascardo <cascardo@holoscopio.com> Acked-by: Dan Carpenter <error27@gmail.com> Acked-by: Mihai Moldovan <ionic@ionic.de> Acked-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de> Acked-by: Sven Neumann <s.neumann@raumfeld.com> Acked-by: Johannes Berg <johannes@sipsolutions.net> Acked-by: Tomas Winkler <tomas.winkler@intel.com> Acked-by: Tony Vroon <tony@linx.net> Acked-by: Pavel Roskin <proski@gnu.org> Acked-by: Bob Copeland <me@bobcopeland.com> Acked-by: Lucas De Marchi <lucas.demarchi@profusion.mobi> Acked-by: Pat Erley <pat-lkml@erley.org> Acked-by: Tejun Heo <tj@kernel.org> Acked-by: John W. Linville <linville@tuxdriver.com> Acked-by: Chris Wright <chrisw@sous-sol.org> Acked-by: Joe Perches <joe@perches.com> Acked-by: Paul Gortmaker <paul.gortmaker@windriver.com> Acked-by: John Gordon <john@devicescape.com> Acked-by: Simon Barber <protocolmagic@gmail.com> Acked-by: Rajkumar Manoharan <rmanohar@qca.qualcomm.com> Acked-by: Jiri Benc <jbenc@upir.cz> Acked-by: Bruno Randolf <br1@einfach.org> Acked-by: Scott James Remnant <keybuk@google.com> Acked-by: Roel Kluin <roel.kluin@gmail.com> Signed-off-by: Luis R. Rodriguez <mcgrof@qca.qualcomm.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
2012-01-04cfg80211: replace reg.c Nokia commit 269ac5Luis R. Rodriguez
Nokia hasn't gotten back to me in over 1 month for a relicense change request. There are only a few changes that they contributed, so just reverting their changes but replacing with another set. This change replaces this commit: commit 269ac5fd2d75b118d76a2291e28796527db2f3f8 Author: Kalle Valo <kalle.valo@nokia.com> Date: Tue Dec 1 10:47:15 2009 +0200 cfg80211: indent regulatory messages with spaces The regulatory messages in syslog look weird: kernel: cfg80211: Regulatory domain: US kernel: ^I(start_freq - end_freq @ bandwidth), (max_antenna_gain, max_eirp) kernel: ^I(2402000 KHz - 2472000 KHz @ 40000 KHz), (600 mBi, 2700 mBm) kernel: ^I(5170000 KHz - 5190000 KHz @ 40000 KHz), (600 mBi, 2300 mBm) kernel: ^I(5190000 KHz - 5210000 KHz @ 40000 KHz), (600 mBi, 2300 mBm) kernel: ^I(5210000 KHz - 5230000 KHz @ 40000 KHz), (600 mBi, 2300 mBm) kernel: ^I(5230000 KHz - 5330000 KHz @ 40000 KHz), (600 mBi, 2300 mBm) kernel: ^I(5735000 KHz - 5835000 KHz @ 40000 KHz), (600 mBi, 3000 mBm) Indent them with four spaces instead of the tab character to get prettier output. Signed-off-by: Kalle Valo <kalle.valo@nokia.com> Acked: Luis R. Rodriguez <lrodriguez@atheros.com> Signed-off-by: John W. Linville <linville@tuxdriver.com> Cc: Petri Karhula <petri.karhula@nokia.com> Signed-off-by: Luis R. Rodriguez <mcgrof@qca.qualcomm.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
2012-01-04cfg80211: replace reg.c Nokia commit c4c32294Luis R. Rodriguez
Nokia hasn't gotten back to me in over 1 month for a relicense change request. There are only a few changes that they contributed, so just reverting their changes but replacing with another set. This change replaces this commit: commit c4c322941ce0d7e2b7b8794ad70683123d9cb26a Author: Yuri Ershov <ext-yuri.ershov@nokia.com> Date: Tue Jun 29 15:08:08 2010 +0400 cfg80211: Update of regulatory request initiator handling In some cases there could be possible dereferencing freed pointer. The update is intended to avoid this issue. Signed-off-by: Yuri Ershov <ext-yuri.ershov@nokia.com> Signed-off-by: John W. Linville <linville@tuxdriver.com> Cc: Petri Karhula <petri.karhula@nokia.com> Signed-off-by: Luis R. Rodriguez <mcgrof@qca.qualcomm.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
2012-01-04ath9k_hw: fix sparse complaint on ar9003_switch_com_spdt_get()Luis R. Rodriguez
This fixes this sparse complaint: make C=2 CF="-D__CHECK_ENDIAN__" M=drivers/net/wireless/ath/ CHECK drivers/net/wireless/ath/ath9k/ar9003_eeprom.c drivers/net/wireless/ath/ath9k/ar9003_eeprom.c:3544:21: warning: incorrect type in assignment (different base types) drivers/net/wireless/ath/ath9k/ar9003_eeprom.c:3544:21: expected restricted __le32 [usertype] val drivers/net/wireless/ath/ath9k/ar9003_eeprom.c:3544:21: got restricted __le16 [usertype] switchcomspdt drivers/net/wireless/ath/ath9k/ar9003_eeprom.c:3546:21: warning: incorrect type in assignment (different base types) drivers/net/wireless/ath/ath9k/ar9003_eeprom.c:3546:21: expected restricted __le32 [usertype] val drivers/net/wireless/ath/ath9k/ar9003_eeprom.c:3546:21: got restricted __le16 [usertype] switchcomspdt The eep->modalHeader5G.switchcomspdt is a le16 and we return u16, so just return le16_to_cpu(). Cc: Felix Fietkau <nbd@openwrt.org> Signed-off-by: Luis R. Rodriguez <mcgrof@qca.qualcomm.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
2012-01-04ath5k: avoid sparse warnings on tracingLuis R. Rodriguez
Just skip the sparse checks on tracing. CHECK drivers/net/wireless/ath/ath5k/base.c include/trace/../../drivers/net/wireless/ath/ath5k/trace.h:19:1: error: incompatible types for operation (<) include/trace/../../drivers/net/wireless/ath/ath5k/trace.h:19:1: left side has type struct ath5k_hw *<noident> include/trace/../../drivers/net/wireless/ath/ath5k/trace.h:19:1: right side has type int include/trace/../../drivers/net/wireless/ath/ath5k/trace.h:37:1: error: incompatible types for operation (<) include/trace/../../drivers/net/wireless/ath/ath5k/trace.h:37:1: left side has type struct ath5k_hw *<noident> include/trace/../../drivers/net/wireless/ath/ath5k/trace.h:37:1: right side has type int include/trace/../../drivers/net/wireless/ath/ath5k/trace.h:63:1: error: incompatible types for operation (<) include/trace/../../drivers/net/wireless/ath/ath5k/trace.h:63:1: left side has type struct ath5k_hw *<noident> include/trace/../../drivers/net/wireless/ath/ath5k/trace.h:63:1: right side has type int /home/mcgrof/wireless-testing/arch/x86/include/asm/jump_label.h:16:9: error: bad asm output /home/mcgrof/wireless-testing/arch/x86/include/asm/jump_label.h:16:9: error: bad asm output /home/mcgrof/wireless-testing/arch/x86/include/asm/jump_label.h:16:9: error: bad asm output /home/mcgrof/wireless-testing/arch/x86/include/asm/jump_label.h:16:9: error: bad asm output CC [M] drivers/net/wireless/ath/ath5k/base.o Signed-off-by: Luis R. Rodriguez <mcgrof@qca.qualcomm.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
2012-01-04ath9k: fix tx queue sparse complaintLuis R. Rodriguez
This fixes this rant from sparse: CHECK drivers/net/wireless/ath/ath9k/xmit.c drivers/net/wireless/ath/ath9k/xmit.c:107:13: warning: context imbalance in 'ath_txq_lock' - wrong count at exit drivers/net/wireless/ath/ath9k/xmit.c:112:13: warning: context imbalance in 'ath_txq_unlock' - unexpected unlock drivers/net/wireless/ath/ath9k/xmit.c:123:30: warning: context imbalance in 'ath_txq_unlock_complete' - unexpected unlock CC [M] drivers/net/wireless/ath/ath9k/xmit. Signed-off-by: Luis R. Rodriguez <mcgrof@qca.qualcomm.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
2012-01-04ath9k_hw: fix sparse warnings on ar9003_rtt.cLuis R. Rodriguez
This fixes these sparse warnings: CHECK drivers/net/wireless/ath/ath9k/ar9003_rtt.c drivers/net/wireless/ath/ath9k/ar9003_rtt.c:36:6: warning: symbol 'ar9003_hw_rtt_enable' was not declared. Should it be static? drivers/net/wireless/ath/ath9k/ar9003_rtt.c:41:6: warning: symbol 'ar9003_hw_rtt_disable' was not declared. Should it be static? drivers/net/wireless/ath/ath9k/ar9003_rtt.c:46:6: warning: symbol 'ar9003_hw_rtt_set_mask' was not declared. Should it be static? drivers/net/wireless/ath/ath9k/ar9003_rtt.c:52:6: warning: symbol 'ar9003_hw_rtt_force_restore' was not declared. Should it be static? drivers/net/wireless/ath/ath9k/ar9003_rtt.c:102:6: warning: symbol 'ar9003_hw_rtt_load_hist' was not declared. Should it be static? drivers/net/wireless/ath/ath9k/ar9003_rtt.c:135:6: warning: symbol 'ar9003_hw_rtt_fill_hist' was not declared. Should it be static? drivers/net/wireless/ath/ath9k/ar9003_rtt.c:143:6: warning: symbol 'ar9003_hw_rtt_clear_hist' was not declared. Should it be stati Signed-off-by: Luis R. Rodriguez <mcgrof@qca.qualcomm.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
generated by cgit v1.2.3-70-g09d2 (git 2.46.0) at 2024-12-14 09:00:21 +0000