summaryrefslogtreecommitdiffstats
AgeCommit message (Collapse)Author
2009-12-02netxen : fix debug tools access for NX2031Narender Kumar
Driver maps only some part of the MMIO bar 0 in case of NX2031. This is sufficient for tx and rx by the driver. When debug tools need to access resources in unmapped regions, driver needs to map these on the fly in order to complete read/write request. Signed-off-by: Narender Kumar <narender.kumar@qlogic.com> Signed-off-by: Dhananjay Phadke <dhananjay.phadke@qlogic.com> Signed-off-by: Amit Kumar Salecha <amit.salecha@qlogic.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2009-12-02e1000e: correct ICH/PCH PHY operations function pointersBruce Allan
Some function pointers for a few PHY operations (for 82578 and 82567) and were set incorrectly causing functions to be executed that were accessing incorrect PHY register offsets for that particular device. This patch also moves a few PHY-specific functions from ich8lan.c to the more appropriate phy.c. Signed-off-by: Bruce Allan <bruce.w.allan@intel.com> Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2009-12-02e1000e: refactor PHY ID detection workaroundBruce Allan
The workaround that detects the correct PHY ID when an initial read of the PHY ID registers returns an invalid one should retry up to ten times with a small delay between attempts using a single PHY address and then repeat using the remaining possible PHY addresses. Do this instead of trying each possible PHY address repeating that up to 100 times. Signed-off-by: Bruce Allan <bruce.w.allan@intel.com> Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2009-12-02e1000e: check_polarity function pointers not set for 8257xBruce Allan
The function pointers for 8257x devices are not set. This is not really a problem now because there is nothing in the driver that references the pointers for this particular MAC-family (the appropriate functions are called directly), but the pointers should be set in case they are used in the future. Signed-off-by: Bruce Allan <bruce.w.allan@intel.com> Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2009-12-02skbuff: remove skb_dma_map/unmapAlexander Duyck
The two functions skb_dma_map/unmap are unsafe to use as they cause problems when packets are cloned and sent to multiple devices while a HW IOMMU is enabled. Due to this it is best to remove the code so it is not used by any other network driver maintainters. Signed-off-by: Alexander Duyck <alexander.h.duyck@intel.com> Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2009-12-02tg3: remove use of skb_dma_map/unmapAlexander Duyck
Due to the fact that skb_dma_map/unmap do not work correctly when a HW IOMMU is enabled it has been recommended to go about removing the calls from the network device drivers. Signed-off-by: Alexander Duyck <alexander.h.duyck@intel.com> Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com> CC: Matt Carlson <mcarlson@broadcom.com> CC: Michael Chan <mchan@broadcom.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2009-12-02be2net: remove use of skb_dma_map/unmapAlexander Duyck
Due to the fact that skb_dma_map/unmap do not work correctly when a HW IOMMU is enabled it has been recommended to go about removing the calls from the network device drivers. Signed-off-by: Alexander Duyck <alexander.h.duyck@intel.com> Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com> CC: Eilon Greenstein <eilong@broadcom.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2009-12-02bnx2: remove skb_dma_map/unmap calls from driverAlexander Duyck
Due to the fact that skb_dma_map/unmap do not work correctly when a HW IOMMU is enabled it has been recommended to go about removing the calls from the network device drivers. [ Fix bnx2_free_tx_skbs() ring indexing and use NETDEV_TX_OK return code in bnx2_start_xmit() after cleaning up DMA mapping errors. -Mchan ] Signed-off-by: Alexander Duyck <alexander.h.duyck@intel.com> Signed-off-by: Michael Chan <mchan@broadcom.com> Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2009-12-02igbvf: remove skb_dma_map/unmap call from driversAlexander Duyck
This patch removes the skb_dma_map/unmap calls from the igbvf driver due to the fact that it does not play well with HW IOMMU when combined with transmitting cloned skbs. Signed-off-by: Alexander Duyck <alexander.h.duyck@intel.com> Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2009-12-02igb: remove use of skb_dma_map from driverAlexander Duyck
This change removes skb_dma_map/unmap calls from the igb driver due to the fact that the call is incompatible with iommu enabled kernels. In order to prevent warnings about using the wrong unmap call I have added a mapped_as_page value to the buffer_info structure to track if the mapped region is a page or a buffer. Signed-off-by: Alexander Duyck <alexander.h.duyck@intel.com> Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2009-12-02ixgbe: remove skb_dma_map/unmap calls from driverAlexander Duyck
This patch removes skb_dma_map/unmap calls from the ixgbe driver due to the fact that the calls don't work with HW IOMMU enabled systems. The problem is that multiple mappings will give different results when HW IOMMU is enabled and the skb_dma_map/unmap calls only have one location to store mappings. Signed-off-by: Alexander Duyck <alexander.h.duyck@intel.com> Acked-by: Peter P Waskiewicz Jr <peter.p.waskiewicz.jr@intel.com> Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2009-12-02ixgb: remove use of skb_dma_map from ixgbAlexander Duyck
skb_dma_map is incompatible with HW iommu due to the fact that multiple mappings can result in different results each time. For this reason it is best to just remove use of these function calls. Signed-off-by: Alexander Duyck <alexander.h.duyck@intel.com> Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2009-12-02e1000: remove use of skb_dma_map from e1000 driverAlexander Duyck
Remove the use of skb_dma_map from the e1000 driver in order to avoid issues when HW iommu are in use. Signed-off-by: Alexander Duyck <alexander.h.duyck@intel.com> Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2009-12-02e1000e: remove use of skb_dma_map from e1000e driverAlexander Duyck
In testing we have found that skb_dma_map/unmap is incompatible with HW IOMMU due to the fact that multiple mappings will return different results. In order to correct this we need to remove skb_dma_map/unmap calls from the e1000e driver. Signed-off-by: Alexander Duyck <alexander.h.duyck@intel.com> Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2009-12-02net: Coding style corrections on Sealevel Systems 4021 driver.Rudy Matela
Changed braces position on some statements. Inserted a space between an "if" keyword and a parenthesis. Signed-off-by: Rudy Matela <rudy.matela@gmail.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2009-12-02net: compat_sys_recvmmsg user timespec arg can be NULLJean-Mickael Guerin
We must test if user timespec is non-NULL before copying from userpace, same as sys_recvmmsg(). Commiter note: changed it so that we have just one branch. Signed-off-by: Jean-Mickael Guerin <jean-mickael.guerin@6wind.com> Signed-off-by: Arnaldo Carvalho de Melo <acme@redhat.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2009-12-02net: compat_mmsghdr must be used in sys_recvmmsgJean-Mickael Guerin
Both to traverse the entries and to set the msg_len field. Commiter note: folded two patches and avoided one branch repeating the compat test. Signed-off-by: Jean-Mickael Guerin <jean-mickael.guerin@6wind.com> Signed-off-by: Arnaldo Carvalho de Melo <acme@redhat.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2009-12-02sctp: fix sctp_setsockopt_autoclose compile warningAndrei Pelinescu-Onciul
Fix the following warning, when building on 64 bits: net/sctp/socket.c:2091: warning: large integer implicitly truncated to unsigned type Signed-off-by: Andrei Pelinescu-Onciul <andrei@iptel.org> Acked-by: Vlad Yasevich <vladislav.yasevich@hp.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2009-12-02ieee802154: merge cleanupEric Dumazet
A small cleanup after last net-2.6 merge into net-next-2.6 As we are going to free skb, no need to set skb->skb_iif or skb->dev Signed-off-by: Eric Dumazet <eric.dumazet@gmail.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2009-12-02net/ps3: Add support for gelic link negotiationHideyuki Sasaki
Add ethtool_ops.set_settings support to the PS3 gelic network driver. Allows manual setting of ethernet link speed. Signed-off-by: Hideyuki Sasaki <xhide@rd.scei.sony.co.jp> Signed-off-by: Geoff Levand <geoffrey.levand@am.sony.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2009-12-02net/ps3: Cleanup gelic enumsGeoff Levand
Cleanup of the gelic driver enumerations: o Add some missing commas. o Add an Ether port post fix (PS3 currently only supports PORT_0). o Add a new enum gelic_lv1_phy to use when interacting with the PHY. Signed-off-by: Geoff Levand <geoffrey.levand@am.sony.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2009-12-02be2net: fix unnecessary access to hardware to get link, port infoAjit Khaparde
Every time while doing ethtool->get_settings we are accessing the hardware to get link status and port information. This is not necessary. We now use the cached copy for this info and update it when the link status changes. From: Suresh R <sureshr@serverengines.com> Signed-off-by: Ajit Khaparde <ajitk@serverengines.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2009-12-02be2net: Add be_rx_polls counterAjit Khaparde
Add be_rx_polls to count number of times NAPI called rx poll function. Signed-off-by: Ajit Khaparde <ajitk@serverengines.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2009-12-02be2net: fix to allow port beacon when device is closedAjit Khaparde
port identification/beaconing is failing if device open has not been done. Fixing it. Signed-off-by: Ajit Khaparde <ajitk@serverengines.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2009-12-02be2net: check for valid ether addressAjit Khaparde
Allow only valid ether addresses to be assigned and used for the interface. Signed-off-by: Ajit Khaparde <ajitk@serverengines.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2009-12-02be2net: initialize netdev->perm_addrAjit Khaparde
patch to initialize netdev->perm_addr Signed-off-by: Ajit Khaparde <ajitk@serverengines.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2009-12-02be2net: set netdev->vlan_features appropriatelyAjit Khaparde
patch to initialize netdev->vlan_features appropriately. Signed-off-by: Ajit Khaparde <ajitk@serverengines.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2009-12-02e1000e: Use sizeof struct rather than pointer in e1000_get_eeprom()Roel Kluin
Don't use the sizeof the pointer to clear the result Signed-off-by: Roel Kluin <roel.kluin@gmail.com> Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2009-12-02e1000e: PHY type cleanups in e1000e_check_downshift()Bruce Allan
Remove the case for 82577 because it does not support the ability to check for downshift. Add case for e1000_phy_bm which can do this. Signed-off-by: Bruce Allan <bruce.w.allan@intel.com> Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2009-12-02e1000e: add debug messagesBruce Allan
Add some helpful debug messages. Signed-off-by: Bruce Allan <bruce.w.allan@intel.com> Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2009-12-02e1000e: comment correctionsBruce Allan
Signed-off-by: Bruce Allan <bruce.w.allan@intel.com> Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2009-12-02e1000e: enable new 82567V-3 deviceBruce Allan
This new PCI device ID is for a new combination of MAC and PHY both of which already have supporting code in the driver, just not yet in this combination. During validation of the device, an intermittent issue was discovered with waking it from a suspended state which can be resolved with the pre-existing workaround to disable gigabit speed prior to suspending. Signed-off-by: Bruce Allan <bruce.w.allan@intel.com> Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2009-12-02e1000e: ensure the link state is correct for serdes linksBruce Allan
This patch ensures that the link state (as reported in mac->serdes_has_link) will transition to false when autoneg fails to complete but valid codewords were detected. Signed-off-by: Bruce Allan <bruce.w.allan@intel.com> Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2009-12-02e1000e: provide family-specific PHY power up/down operationsBruce Allan
The different families (80003es2lan, 8257x, ICHx/PCH) supported by the driver each have their own conditions when the PHY can be powered down. This patch rewrites the PHY power up/down code to fit with the family- specific style used in the driver. All pre-existing calls to power up or down the PHY remain untouched. A new call to power down the PHY when removing the driver when the interface is down replaces the current call to reset the PHY in order to reduce power consumption. Signed-off-by: Bruce Allan <bruce.w.allan@intel.com> Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2009-12-02e1000e: guard against buffer overflow in cable length tablesBruce Allan
Signed-off-by: Bruce Allan <bruce.w.allan@intel.com> Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2009-12-02e1000e: provide family-specific functions to manage VLAN filter arraysBruce Allan
The two MAC-families that have VLAN filter table register arrays manage each a bit differently from one another, so provide family-specific functions for managing the register arrays and function pointers to access the appropriate function. Also make sure attempts to access these register arrays are not done on parts not supporting that feature. Signed-off-by: Bruce Allan <bruce.w.allan@intel.com> Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2009-12-01Merge branch 'master' of ↵David S. Miller
master.kernel.org:/pub/scm/linux/kernel/git/davem/net-2.6 Conflicts: net/mac80211/ht.c
2009-12-01net: remove [un]register_pernet_gen_... and update the docs.Eric W. Biederman
No that all of the callers have been updated to set fields in struct pernet_operations, and simplified to let the network namespace core handle the allocation and freeing of the storage for them, remove the surpurpflous methods and update the docs to the new style. Signed-off-by: Eric W. Biederman <ebiederm@xmission.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2009-12-01net: Simplify ipip6 aka sit pernet operations.Eric W. Biederman
Take advantage of the new pernet automatic storage management, and stop using compatibility network namespace functions. Signed-off-by: Eric W. Biederman <ebiederm@xmission.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2009-12-01net: Simplify ip6_tunnel pernet operations.Eric W. Biederman
Take advantage of the new pernet automatic storage management, and stop using compatibility network namespace functions. Signed-off-by: Eric W. Biederman <ebiederm@xmission.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2009-12-01net: Simplify ipip pernet operations.Eric W. Biederman
Take advantage of the new pernet automatic storage management, and stop using compatibility network namespace functions. Signed-off-by: Eric W. Biederman <ebiederm@xmission.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2009-12-01net: Simplify ip_gre pernet operations.Eric W. Biederman
Take advantage of the new pernet automatic storage management, and stop using compatibility network namespace functions. Signed-off-by: Eric W. Biederman <ebiederm@xmission.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2009-12-01net: Simplify phonet pernet operations.Eric W. Biederman
Take advantage of the new pernet automatic storage management, and stop using compatibility network namespace functions. Signed-off-by: Eric W. Biederman <ebiederm@xmission.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2009-12-01net: Simplify pppol2tp pernet operations.Eric W. Biederman
Take advantage of the new pernet automatic storage management, and stop using compatibility network namespace functions. Signed-off-by: Eric W. Biederman <ebiederm@xmission.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2009-12-01net: Simplify pppoe pernet operations.Eric W. Biederman
Take advantage of the new pernet automatic storage management, and stop using compatibility network namespace functions. Signed-off-by: Eric W. Biederman <ebiederm@xmission.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2009-12-01net: Simplify ppp_generic pernet operations.Eric W. Biederman
Take advantage of the new pernet automatic storage management, and stop using compatibility network namespace functions. Signed-off-by: Eric W. Biederman <ebiederm@xmission.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2009-12-01net: Simplify conntrack_proto_gre pernet operations.Eric W. Biederman
Take advantage of the new pernet automatic storage management, and stop using compatibility network namespace functions. Signed-off-by: Eric W. Biederman <ebiederm@xmission.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2009-12-01net: Simplify conntrack_proto_dccp pernet operations.Eric W. Biederman
Take advantage of the new pernet automatic storage management, and stop using compatibility network namespace functions. Signed-off-by: Eric W. Biederman <ebiederm@xmission.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2009-12-01net: Simplify af_key pernet operations.Eric W. Biederman
Take advantage of the new pernet automatic storage management, and stop using compatibility network namespace functions. Signed-off-by: Eric W. Biederman <ebiederm@xmission.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2009-12-01net: Simplify vlan pernet operations.Eric W. Biederman
Take advantage of the new pernet automatic storage management, and stop using compatibility network namespace functions. Signed-off-by: Eric W. Biederman <ebiederm@xmission.com> Signed-off-by: David S. Miller <davem@davemloft.net>