Age | Commit message (Collapse) | Author |
|
When grabbing composite video with Iomega Buz, the stock driver will
prevent grabbing from the same input twice in a row, forcing the user to
switch inputs before anything useful can be grabbed again. It is caused by
some optimization code in the input selection parts, and triggered by the
saa7111_command() executing cmd 0. The attached patch will remedy this by
disabling cmd 0 altogether; a fix that has no found negative effects on the
rest of the code. In fact, saa7110.c does the exact same thing.
Acked-by: Ronald S. Bultje <rbultje@ronald.bitfreak.net>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
|
|
Cleanups to the zr36057 initialization:
* Drop intermediate local variables.
* Single error path.
Also drop a needless cast on kfree.
Signed-off-by: Jean Delvare <khali@linux-fr.org>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
|
|
Explicitely state the number of registers the SAA7111 has, and use that
defined value where relevant. This should prevent any future array overrun
like the one I just fixed in the saa7110 driver.
This patch also saves 8 bytes of memory as a side effect, as the register
cache was larger than needed.
Signed-off-by: Jean Delvare <khali@linux-fr.org>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
|
|
Fix the i2c block write mode of the saa7114 driver. A previous code change
accidentally commented out a local variable increment, which should have been
kept, causing the register writes over the I2C bus to never be batched,
replacing any attempted block write by slower, individual write transactions.
Also drop the commented out code, as it only adds to confusion.
Signed-off-by: Jean Delvare <khali@linux-fr.org>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
|
|
* git://git.kernel.org/pub/scm/linux/kernel/git/paulus/powerpc: (78 commits)
[PATCH] powerpc: Add FSL SEC node to documentation
[PATCH] macintosh: tidy-up driver_register() return values
[PATCH] powerpc: tidy-up of_register_driver()/driver_register() return values
[PATCH] powerpc: via-pmu warning fix
[PATCH] macintosh: cleanup the use of i2c headers
[PATCH] powerpc: dont allow old RTC to be selected
[PATCH] powerpc: make powerbook_sleep_grackle static
[PATCH] powerpc: Fix warning in add_memory
[PATCH] powerpc: update mailing list addresses
[PATCH] powerpc: Remove calculation of io hole
[PATCH] powerpc: iseries: Add bootargs to /chosen
[PATCH] powerpc: iseries: Add /system-id, /model and /compatible
[PATCH] powerpc: Add strne2a() to convert a string from EBCDIC to ASCII
[PATCH] powerpc: iseries: Make more stuff static in platforms/iseries/mf.c
[PATCH] powerpc: iseries: Remove pointless iSeries_(restart|power_off|halt)
[PATCH] powerpc: iseries: mf related cleanups
[PATCH] powerpc: Replace platform_is_lpar() with a firmware feature
[PATCH] powerpc: trivial: Cleanup whitespace in cputable.h
[PATCH] powerpc: Remove unused iommu_off logic from pSeries_init_early()
[PATCH] powerpc: Unconfuse htab_bolt_mapping() callers
...
|
|
Documentation: Added FSL SOC SEC node definition
Updated the documentation to include the definition of the SEC device
node format for Freescale SOC devices.
Signed-off-by: Kim Phillips <kim.phillips@freescale.com>
Signed-off-by: Paul Mackerras <paulus@samba.org>
|
|
Remove the assumption that driver_register() returns the number of devices
bound to the driver. In fact, it returns zero for success or a negative
error value.
All callers of macio_register_driver() either ignore the return value or
return it as the return value of a module_init() function.
Signed-off-by: Bjorn Helgaas <bjorn.helgaas@hp.com>
Cc: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Paul Mackerras <paulus@samba.org>
|
|
Remove the assumption that driver_register() returns the number of devices
bound to the driver. In fact, it returns zero for success or a negative
error value.
Nobody uses the return value of of_register_driver() anyway.
Signed-off-by: Bjorn Helgaas <bjorn.helgaas@hp.com>
Acked-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Paul Mackerras <paulus@samba.org>
|
|
drivers/macintosh/via-pmu.c:164: warning: `sleep_in_progress' defined but not used
Cc: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Paul Mackerras <paulus@samba.org>
|
|
Cleanup the use of i2c headers in macintosh drivers.
Signed-off-by: Jean Delvare <khali@linux-fr.org>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Paul Mackerras <paulus@samba.org>
|
|
Now powerpc uses the generic RTC stuff we should not enable the old RTC.
Doing so will result in hangs at boot.
Signed-off-by: Anton Blanchard <anton@samba.org>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Paul Mackerras <paulus@samba.org>
|
|
powerbook_sleep_grackle is only called inside via-pmu, from pmu_ioctl()
Signed-off-by: Olaf Hering <olh@suse.de>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Paul Mackerras <paulus@samba.org>
|
|
arch/powerpc/mm/mem.c: In function `add_memory':
arch/powerpc/mm/mem.c:128: warning: assignment makes integer from pointer without a cast
Cc: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Paul Mackerras <paulus@samba.org>
|
|
master.kernel.org:/pub/scm/linux/kernel/git/jgarzik/netdev-2.6
* 'upstream-linus' of master.kernel.org:/pub/scm/linux/kernel/git/jgarzik/netdev-2.6:
[PATCH] Use of uninitialized variable in drivers/net/depca.c
[PATCH] Use after free in net/tulip/de2104x.c
[PATCH] sis900 adm7001 PHY support
[PATCH] sky2: more ethtool stats
[PATCH] s390: qeth :allow setting of attribute "route6" to "no_router".
[PATCH] s390: qeth driver cleanups
[PATCH] s390: qeth driver statistics fixes
[PATCH] AMD Au1xx0: fix Ethernet TX stats
[PATCH] fix spidernet build issue
|
|
If the debug driver is built-in, link it in last, so that any real
drivers will probe first, rather than having the debug driver pick the
first scsi slots..
Signed-off-by: Douglas Gilbert <dougg@torque.net>
Signed-off-by: Randy Dunlap <rdunlap@xenotime.net>
Acked-by: James Bottomley <James.Bottomley@SteelEye.com>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
|
|
* master.kernel.org:/pub/scm/linux/kernel/git/davem/net-2.6:
[TCP]: Do not use inet->id of global tcp_socket when sending RST.
[NETFILTER]: Fix undefined references to get_h225_addr
[NETFILTER]: futher {ip,ip6,arp}_tables unification
[NETFILTER]: Fix xt_policy address matching
[NETFILTER]: nf_conntrack: support for layer 3 protocol load on demand
[NETFILTER]: x_tables: set the protocol family in x_tables targets/matches
[NETFILTER]: conntrack: cleanup the conntrack ID initialization
[NETFILTER]: nfnetlink_queue: fix nfnetlink message size
[NETFILTER]: ctnetlink: Fix expectaction mask dumping
[NETFILTER]: Fix Kconfig typos
[NETFILTER]: Fix ip6tables breakage from {get,set}sockopt compat layer
|
|
* master.kernel.org:/home/rmk/linux-2.6-serial:
[SERIAL] Merge avlab serial board entries in parport_serial
[SERIAL] kernel console should send CRLF not LFCR
|
|
* master.kernel.org:/home/rmk/linux-2.6-arm: (45 commits)
[ARM] 3389/1: typo and grammar fix
[ARM] 3386/1: AT91RM9200 Clock update
[ARM] 3384/1: AT91RM9200: Timer
[ARM] 3382/1: ixp2000: unify defconfigs
[ARM] 3381/1: ixp2000: fix slowport write timing control register fields
[ARM] 3380/1: ixp2000: simplify ixdp2x00_master_npu() check
[ARM] 3379/1: ixp2000: use generic 8250 debug macros
[ARM] 3378/1: ixp2000: fix gpio interrupt handling
[ARM] Quieten spurious IRQ detection
[ARM] Use kcalloc to allocate counter_config array rather than kmalloc
[ARM] Oprofile: dynamically allocate counter_config
[ARM] Oprofile: Convert semaphore to mutex
[ARM] 3376/2: S3C2410 - update defconfig
[ARM] 3375/1: S3C2440 - fix osiris machine build
[ARM] 3374/1: ep93xx: gpio interrupt support
[ARM] 3361/1: S3C24XX - add USB bus clock source
[ARM] 3360/1: S3C2440 - add set rate methods and camera clock
[ARM] 3359/1: S3C24XX - add support for clk_set_rate
[ARM] Convert kmalloc+memset to kzalloc
[ARM] 3373/1: move uengine loader to arch/arm/common
...
|
|
hi,
this fixes coverity bug #888, where the variable
dev is used uninitialized. I assume the programmer
meant to use mdev, which is initialized.
Compile tested only.
Signed-off-by: Eric Sesterhenn <snakebyte@gmx.de>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
|
|
hi,
this fixes coverity bug #912, where skb is freed first,
and dereferenced a few lines later with skb->len.
Signed-off-by: Eric Sesterhenn <snakebyte@gmx.de>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
|
|
this patch is required to get a SIS964 based motherboard ethernet working (FSC D1875)
(picking the #1 transceiver, instead of the last one, in case no known ones were found
might be a better default, and would have worked in this case too)
Signed-off-by: Artur Skawina <art_k@o2.pl>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
|
|
Expose all the available hardware statistics via ethtool.
And cleanup some of the statistics definitions.
Signed-off-by: Stephen Hemminger <shemminger@osdl.org>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
|
|
[patch 4/6] s390: qeth :allow setting of attribute "route6" to "no_router".
From: Ursula Braun <braunu@de.ibm.com>
when setting route6 attribute back to no_router qeth does not
issue an IP ASSIST command to reset router value to no_router.
Once primary_router is set device stays in this mode.
Issue an IP ASSIST command when no_router is set in route6.
Device will be reset and thus will not longer run as a primary
router.
Signed-off-by: Frank Pavlic <fpavlic@de.ibm.com>
diffstat:
qeth_main.c | 5 -----
1 files changed, 5 deletions(-)
Signed-off-by: Jeff Garzik <jeff@garzik.org>
|
|
[patch 3/6] s390: qeth driver cleanups
From: Ursula Braun <braunu@de.ibm.com>
- code analyzing tool BEAM has found some unreachable
and unnecessary statements and also conditions
which are always true.
- removed some useless MII code since OSA card will never
allow to set such values.
Signed-off-by: Frank Pavlic <fpavlic@de.ibm.com>
diffstat:
qeth_main.c | 49 ++++---------------------------------------------
qeth_proc.c | 18 +++++++++---------
qeth_sys.c | 2 +-
3 files changed, 14 insertions(+), 55 deletions(-)
Signed-off-by: Jeff Garzik <jeff@garzik.org>
|
|
[patch 2/6] s390: qeth driver statistics fixes
From: Ursula Braun <braunu@de.ibm.com>
- display "unsigned int" values in /proc/qeth_perf with %u instead of %i
- omit qdio header length when increasing card->stats.tx_bytes
Signed-off-by: Frank Pavlic <fpavlic@de.ibm.com>
diffstat:
qeth_main.c | 3 ++-
qeth_proc.c | 38 +++++++++++++++++++-------------------
2 files changed, 21 insertions(+), 20 deletions(-)
Signed-off-by: Jeff Garzik <jeff@garzik.org>
|
|
With Au1xx0 Ethernet driver, TX bytes/packets always remain zero. The
problem seems to be that when packet has been transmitted, the length word
in DMA buffer is zero.
The patch updates the TX stats when a buffer is fed to DMA. The initial
2.4 patch was posted to linux-mips@linux-mips.org by Thomas Lange 21 Jan
2005.
Signed-off-by: Thomas Lange <thomas@corelatus.se>
Signed-off-by: Sergei Shtylyov <sshtylyov@ru.mvista.com>
Cc: Jordan Crouse <jordan.crouse@amd.com>
Cc: Jeff Garzik <jgarzik@pobox.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
|
|
<unchangelogged>
Signed-off-by: Jens Osterkamp <Jens.Osterkamp@de.ibm.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
|
|
Now that libata is smart enought to handle both soft and hard resets,
add softreset method.
Signed-off-by: Tejun Heo <htejun@gmail.com>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
|
|
As libata now can do PIO, don't ignore PIO-only devices.
Signed-off-by: Tejun Heo <htejun@gmail.com>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
|
|
Signed-off-by: Alan Cox <alan@redhat.com>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
|
|
Not much to say here except that some drives have fixed and bad firmware
Signed-off-by: Alan Cox <alan@redhat.com>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
|
|
The current code follows the spec but uses an overlong delay. This would
be great if the hardware did. Several vendors however forget the D7
pulldown. Fortunately 0xFF isnt a sane reset state so we can use it to
skip detection as is done in drivers/ide. (ie this is a tested solution
over a long time)
Signed-off-by: Alan Cox <alan@redhat.com>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
|
|
Signed-off-by: Alan Cox <alan@redhat.com>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
|
|
|
|
The problem is in ip_push_pending_frames(), which uses:
if (!df) {
__ip_select_ident(iph, &rt->u.dst, 0);
} else {
iph->id = htons(inet->id++);
}
instead of ip_select_ident().
Right now I think the code is a nonsense. Most likely, I copied it from
old ip_build_xmit(), where it was really special, we had to decide
whether to generate unique ID when generating the first (well, the last)
fragment.
In ip_push_pending_frames() it does not make sense, it should use plain
ip_select_ident() instead.
Signed-off-by: Alexey Kuznetsov <kuznet@ms2.inr.ac.ru>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
get_h225_addr is exported, but declared static, which fails when
linking statically.
Signed-off-by: Patrick McHardy <kaber@trash.net>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
This patch moves {ip,ip6,arp}t_entry_{match,target} definitions to
x_tables.h. This move simplifies code and future compatibility fixes.
Signed-off-by: Dmitry Mishin <dim@openvz.org>
Acked-off-by: Kirill Korotaev <dev@openvz.org>
Signed-off-by: Patrick McHardy <kaber@trash.net>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Fix missing inversion in address matching, it was broken during the
conversion to x_tables.
Signed-off-by: Patrick McHardy <kaber@trash.net>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
x_tables matches and targets that require nf_conntrack_ipv[4|6] to work
don't have enough information to load on demand these modules. This
patch introduces the following changes to solve this issue:
o nf_ct_l3proto_try_module_get: try to load the layer 3 connection
tracker module and increases the refcount.
o nf_ct_l3proto_module put: drop the refcount of the module.
Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org>
Signed-off-by: Patrick McHardy <kaber@trash.net>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Set the family field in xt_[matches|targets] registered.
Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org>
Signed-off-by: Patrick McHardy <kaber@trash.net>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Currently the first conntrack ID assigned is 2, use 1 instead.
Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org>
Signed-off-by: Patrick McHardy <kaber@trash.net>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Fix oversized message, use NLMSG_SPACE just one since it reserves space
for the netlink header and NFA_SPACE for every attribute.
Thanks to Harald Welte for the feedback
Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org>
Signed-off-by: Patrick McHardy <kaber@trash.net>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
The expectation mask has some particularities that requires a different
handling. The protocol number fields can be set to non-valid protocols,
ie. l3num is set to 0xFFFF. Since that protocol does not exist, the mask
tuple will not be dumped. Moreover, this results in a kernel panic when
nf_conntrack accesses the array of protocol handlers, that is PF_MAX (0x1F)
long.
This patch introduces the function ctnetlink_exp_dump_mask, that correctly
dumps the expectation mask. Such function uses the l3num value from the
expectation tuple that is a valid layer 3 protocol number. The value of the
l3num mask isn't dumped since it is meaningless from the userspace side.
Thanks to Yasuyuki Kozakai and Patrick McHardy for the feedback.
Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org>
Signed-off-by: Patrick McHardy <kaber@trash.net>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Signed-off-by: Thomas Vögtle <tv@lio96.de>
Signed-off-by: Patrick McHardy <kaber@trash.net>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
do_ipv6_getsockopt returns -EINVAL for unknown options, not
-ENOPROTOOPT as do_ipv6_setsockopt.
Signed-off-by: Patrick McHardy <kaber@trash.net>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Patch from Erik Hovland
I found a typo and what seems to be a run-on sentence in
arch/arm/common/dmabounce.c
This patch corrects both.
Signed-off-by: Erik Hovland <erik@hovland.org>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
|
|
Patch from Andrew Victor
This patch includes a few changes to the clock support on the
AT91RM9200.
1. Added definitions for Ethernet, MMC, TWI, USARTs, and SPI peripheral
clocks.
2. Replaced some hard-coded hex values with the text definitions in
at91rm9200_sys.h.
3. If the USB96M bit is set for PLLB, then the rate of PLLB is not
affected but only the USB Host/Device clocks which are derived from it.
Issue reported by Sergei Sharonov.
Signed-off-by: Andrew Victor <andrew@sanpeople.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
|
|
Patch from Andrew Victor
If the timer interrupt is ever significantly delayed (or after the
system was suspended), the system could spin incrementing the time for
too long.
The fix is to replace the "do {} while" with a "while {}".
Orignal patch by Savin Zlobec and Peter Menzebach.
Signed-off-by: Andrew Victor <andrew@sanpeople.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
|
|
Patch from Lennert Buytenhek
Unify the five existing ixp2000 defconfigs into one defconfig.
Signed-off-by: Lennert Buytenhek <buytenh@wantstofly.org>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
|
|
Patch from Lennert Buytenhek
The original version of the chip docs had the PW and SU fields in
the slowport write timing control register accidentally reversed.
This is mentioned in the errata (documentation change #4) and fixed
in newer docs.
Signed-off-by: Lennert Buytenhek <buytenh@wantstofly.org>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
|