summaryrefslogtreecommitdiffstats
AgeCommit message (Collapse)Author
2005-04-24[PATCH] __get_unaligned() turned into macroAl Viro
Turns __get_unaligned() and __put_unaligned into macros. That is definitely safe; leaving them as inlines breaks on e.g. alpha [try to build ncpfs there and you'll get unresolved symbols since we end up getting __get_unaligned() not inlined]. Signed-off-by: Al Viro <viro@parcelfarce.linux.theplanet.co.uk> Signed-off-by: Linus Torvalds <torvalds@osdl.org>
2005-04-24[PATCH] broken dependency for I2C_MPCAl Viro
All boards dealt with by I2C_MPC are 32bit. Moreover, driver simply won't build on ppc64 - it uses ppc32-only types all over the place. Dependency fixed - it's PPC32, not PPC. Signed-off-by: Al Viro <viro@parcelfarce.linux.theplanet.co.uk> Signed-off-by: Linus Torvalds <torvalds@osdl.org>
2005-04-24[PATCH] missing dependency on sparc64Al Viro
CONFIG_HW_CONSOLE selects vt.c; without the stuff pulled by CONFIG_VT it will not build. Normally we get both in drivers/char/Kconfig and there HW_CONSOLE depends on VT. sparc64 does not pull drivers/char/Kconfig and has that sutff in arch/sparc64/Kconfig instead. However, it forgets to add the same dependency. As the result, turning VT off [which is possible] will end up with broken build. For no good reason... Signed-off-by: Al Viro <viro@parcelfarce.linux.theplanet.co.uk> Signed-off-by: Linus Torvalds <torvalds@osdl.org>
2005-04-24[PATCH] msnd_pinnacle GFP fixAl Viro
Dumb typo - __get_free_page() takes gfp mask (in this case - GFP_KERNEL), not the page size... Signed-off-by: Al Viro <viro@parcelfarce.linux.theplanet.co.uk> Signed-off-by: Linus Torvalds <torvalds@osdl.org>
2005-04-24[PATCH] mempolicy.c GFP fixAl Viro
zonelist_policy() forgot to mask non-zone bits from gfp when comparing zone number with policy_zone. ACKed-by: Andi Kleen <ak@suse.de> Signed-off-by: Al Viro <viro@parcelfarce.linux.theplanet.co.uk> Signed-off-by: Linus Torvalds <torvalds@osdl.org>
2005-04-24[PATCH] SCSI GFP fixesAl Viro
Somebody forgot that | has higher priority than ?:. As the result, allocation is done with bogus flags - instead of GFP_ATOMIC + possibly GFP_DMA we always get GFP_DMA and no GFP_ATOMIC. Signed-off-by: Al Viro <viro@parcelfarce.linux.theplanet.co.uk> Signed-off-by: Linus Torvalds <torvalds@osdl.org>
2005-04-22[IA64] Fix build errors for !HOTPLUG case.Ashok Raj
Signed-off-by: Ashok Raj <ashok.raj@intel.com> Signed-off-by: Tony Luck <tony.luck@intel.com>
2005-04-22[IA64] cpu hotplug: return offlined cpus to SALAshok Raj
This patch is required to support cpu removal for IPF systems. Existing code just fakes the real offline by keeping it run the idle thread, and polling for the bit to re-appear in the cpu_state to get out of the idle loop. For the cpu-offline to work correctly, we need to pass control of this CPU back to SAL so it can continue in the boot-rendez mode. This gives the SAL control to not pick this cpu as the monarch processor for global MCA events, and addition does not wait for this cpu to checkin with SAL for global MCA events as well. The handoff is implemented as documented in SAL specification section 3.2.5.1 "OS_BOOT_RENDEZ to SAL return State" Signed-off-by: Ashok Raj <ashok.raj@intel.com> Signed-off-by: Tony Luck <tony.luck@intel.com>
2005-04-22[IA64] ia32_signal.c: erroneous use of memset/memcpyArun Sharma
Found by Alexander Nyberg, improved by Bjorn Helgaas. - Fix the incorrect argument to sizeof() - looks like memcpy() code pass was dervived from code that used copy_from_user(). But in this case we are doing to kernel space to kernel space copy, so memcpy is the right routine, but it doesn't return an error code. Signed-off-by: Arun Sharma <arun.sharma@intel.com> Signed-off-by: Tony Luck <tony.luck@intel.com>
2005-04-22[PATCH] x86_64: fix new out of line put_user()Alexander Nyberg
The labels after the last put_user patch were misplaced so exceptions on the real mov instructions would not be handled. Noted by Brian Gerst <bgerst@didntduck.org>
2005-04-22Merge rsync://rsync.kernel.org/pub/scm/linux/kernel/git/davem/sparc-2.6.gitLinus Torvalds
2005-04-21[SPARC64]: In sunsab driver, make sure to set the uart timeout.David S. Miller
This breaks serial consoles badly. Thanks to Eric Brower for tracking down the problem. Signed-off-by: David S. Miller <davem@davemloft.net>
2005-04-21[SPARC64]: In sunsu driver, make sure to fully init chip for kbd/msDavid S. Miller
We were forgetting to call sunsu_change_speed(). The reason that replugging in the mouse cable "fixes things" is that causes a BREAK interrupt which in turn caused a call to sunsu_change_speed() which would get the chip setup properly. Signed-off-by: David S. Miller <davem@davemloft.net>
2005-04-21[SPARC]: Provide generic ioctls in Sparc RTC driver.David S. Miller
Provide support for drivers/char/rtc.c ioctls in the Mostek rtc driver as well as the Sparc specific RTCGET and RTCSET. This allows userspace to be much less messy. Currently util-linux and other spots jump through hoops trying various ioctl variants until it hits the right one whatever driver actually being used supports. Eventually all of this should move over to the genrtc.c driver, but not today... While we are here, fix up the register types for sparse. Thanks to Frans Pop for helping point out this issue. Signed-off-by: David S. Miller <davem@davemloft.net>
2005-04-21[SPARC64]: Provide a pgprot_noncached() implementation.David S. Miller
Signed-off-by: David S. Miller <davem@davemloft.net>
2005-04-21[XFRM]: Fix existence lookup in xfrm_state_findPatrick McHardy
Use 'daddr' instead of &tmpl->id.daddr, since the latter might be zero. Also, only perform the lookup when tmpl->id.spi is non-zero. Signed-off-by: Patrick McHardy <kaber@trash.net> Signed-off-by: David S. Miller <davem@davemloft.net>
2005-04-21[TG3]: Add msi testMichael Chan
Add MSI test for chips that support MSI. If MSI test fails, it will switch back to INTx mode and will print a message asking the user to report the failure. Signed-off-by: Michael Chan <mchan@broadcom.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2005-04-21[TG3]: Add msi supportMichael Chan
Add MSI support for 5751 C0 and 5752. Signed-off-by: Michael Chan <mchan@broadcom.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2005-04-21[TG3]: Fix bug in tg3_set_eeprom()Michael Chan
Fix a bug in tg3_set_eeprom() when the length is less than 4 and the offset is not 4-byte aligned. Signed-off-by: Michael Chan <mchan@broadcom.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2005-04-21[TG3]: Add nvram lock-out support for 5752 TPMMichael Chan
Add support for the NVRAM lock-out feature for TPM in 5752. If lock-out is enabled, certain NVRAM registers cannot be written to. Signed-off-by: Michael Chan <mchan@broadcom.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2005-04-21[TG3]: Add nvram detection for 5752Michael Chan
Signed-off-by: Michael Chan <mchan@broadcom.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2005-04-21[TG3]: Add GPIO3 for 5752Michael Chan
Add bit definitions for the new GPIO3 in 5752. GPIO3 must be driven as output when it is unused. Signed-off-by: Michael Chan <mchan@broadcom.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2005-04-21[TG3]: Workaround 5752 A0 chip IDMichael Chan
The 5752 A0 chip ID is wrong in hardware. The simplest way to workaround it is to change it to the correct value in tp->pci_chip_rev_id. This way, it is easier to check for the ASIC_REV_5752 in the rest of the driver. Signed-off-by: Michael Chan <mchan@broadcom.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2005-04-21[TG3]: Fix tg3_set_power_state()Michael Chan
Fix tg3_set_power_state to drive GPIOs properly based on the TG3_FLAG_EEPROM_WRITE_PROTECT flag. Some delays are also added after D0 and D3 power state changes. Signed-off-by: Michael Chan <mchan@broadcom.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2005-04-21[TG3]: Setup proper GPIO settingsMichael Chan
Setup proper GPIO settings in tp->grc_local_ctrl before calling tg3_set_power() state in tg3_get_invariants() and after chip reset. Signed-off-by: Michael Chan <mchan@broadcom.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2005-04-21[TG3]: Split tg3_phy_probe into 2 functionsMichael Chan
Split the 1st half of tg3_phy_probe() into tg3_get_eeprom_hw_cfg() so that the TG3_FLAG_EEPROM_WRITE_PROT can be determined before calling tg3_set_power_state() in tg3_get_invariants(). This will allow tg3_set_power_state() to drive the GPIOs correctly based on the config. information in eeprom. On the 5752, there are no pull-up resistors on the GPIO pins and it is necessary to drive the unused GPIOs as output. Signed-off-by: Michael Chan <mchan@broadcom.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2005-04-21[TG3]: Minor 5752 fixesMichael Chan
Some minor 5752 fixes mostly for correctness and add 5752 PHY ID. Signed-off-by: Michael Chan <mchan@broadcom.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2005-04-21[TG3]: add support for bcm5752 rev a1John W. Linville
Replace existing ASIC_REV_5752 definition with ASIC_REV_5752_A0, and add definition for ASIC_REV_5752_A1. Then, add ASIC_REV_5752_A1 to check for setting TG3_FLG2_5750_PLUS in tg3_get_invariants. Signed-off-by: John W. Linville <linville@tuxdriver.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2005-04-21[TG3]: check TG3_FLG2_5750_PLUS flag to set TG3_FLG2_5705_PLUS flagJohn W. Linville
Use check of TG3_FLG2_5750_PLUS in tg3_get_invariants to set TG3_FLG2_5705_PLUS flag. Signed-off-by: John W. Linville <linville@tuxdriver.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2005-04-21[TG3]: use TG3_FLG2_57{05,50}_PLUS flags in tg3_get_invariantsJohn W. Linville
Rewrite checks in tg3_get_invariants to use TG3_FLG2_5705_PLUS and TG3_FLG2_5750_PLUS flags. Signed-off-by: John W. Linville <linville@tuxdriver.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2005-04-21[TG3]: more use of TG3_FLG2_5705_PLUS flagJohn W. Linville
Rewrite of a couple of troublesome multi-way if statements to use TG3_FLG2_5705_PLUS flag. Signed-off-by: John W. Linville <linville@tuxdriver.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2005-04-21[TG3]: use new TG3_FLG2_5750_PLUS flagJohn W. Linville
Replace a number of two-way if statements checking for 5750, and/or 5752 to reference the newly-defined TG3_FLG2_5750_PLUS flag instead. Signed-off-by: John W. Linville <linville@tuxdriver.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2005-04-21[TG3]: define TG3_FLG2_5750_PLUS flagJohn W. Linville
Define TG3_FLG2_5750_PLUS flag and set it in tg3_get_invariants for ASIC_REV_5750 or ASIC_REV_5752. Signed-off-by: John W. Linville <linville@tuxdriver.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2005-04-21[TG3]: use TG3_FLG2_5705_PLUS instead of multi-way if'sJohn W. Linville
Replace a number of three-way if statements checking for 5705, 5750, and 5752 to reference the equivalent TG3_FLG2_5705_PLUS flag instead. Signed-off-by: John W. Linville <linville@tuxdriver.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2005-04-21[TG3]: add bcm5752 entry to pci_ids.hJohn W. Linville
Add proper entry for bcm5752 PCI ID to pci_ids.h, and use it in tg3. I did this separately in case patches like this (i.e. new PCI IDs) need to come from more "official" sources. Signed-off-by: John W. Linville <linville@tuxdriver.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2005-04-21[TG3]: add bcm5752 to tg3_pci_tblJohn W. Linville
Add hard-coded definition of bcm5752 PCI ID to tg3_pci_tbl. Next patch will change entry to use pci_ids.h-based definition. Signed-off-by: John W. Linville <linville@tuxdriver.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2005-04-21[TG3]: add basic bcm5752 supportJohn W. Linville
Add ASIC_REV_5752 definition. Track-down all references to ASIC_REV_5750 and mirror them with references to the newly defined ASIC_REV_5752. Signed-off-by: John W. Linville <linville@tuxdriver.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2005-04-21[ATM]: net/atm/resources.c: remove __free_atm_devAdrian Bunk
Signed-off-by: Adrian Bunk <bunk@stusta.de> Signed-off-by: Chas Williams <chas@cmf.nrl.navy.mil> Signed-off-by: David S. Miller <davem@davemloft.net>
2005-04-21[AX25]: make ax25_queue_xmit a net_device parameterArnaldo Carvalho de Melo
I.e. not using skb->dev as a way to pass the parameter used to fill... skb->dev :-) Also to get the _type_trans open coded sequence grouped, next changesets will introduce ax25_type_trans. Signed-off-by: Ralf Baechle <ralf@linux-mips.org> Signed-off-by: Arnaldo Carvalho de Melo <acme@ghostprotocols.net> Signed-off-by: David S. Miller <davem@davemloft.net>
2005-04-21[ATM]: sk_atm() conversion missed subtle change of vccChas Williams
Signed-off-by: Chas Williams <chas@cmf.nrl.navy.mil> Signed-off-by: David S. Miller <davem@davemloft.net>
2005-04-21[NET]: Add missing newline for skb_*_panicPatrick McHardy
While we're at it, lets also replace KERN_INFO by KERN_EMERG to make sure the user gets to see it. Signed-off-by: Patrick McHardy <kaber@trash.net> Signed-off-by: David S. Miller <davem@davemloft.net>
2005-04-21[PATCH] fix subarch breakage in amd dual core updatesJames Bottomley
The patch to arch/i386/kernel/cpu/amd.c relies on the variable cpu_core_id which is defined in i386/kernel/smpboot.c. This means it is only present if CONFIG_X86_SMP is defined, not CONFIG_SMP (alternative SMP harnesses won't have it, which is why it breaks voyager). Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com> Signed-off-by: Linus Torvalds <torvalds@osdl.org>
2005-04-21[PATCH] Fix tgafb.c compile failureAdrian Bunk
The untested patch below should fix this compile error. Signed-off-by: Adrian Bunk <bunk@stusta.de> Signed-off-by: Linus Torvalds <torvalds@osdl.org>
2005-04-21[PATCH] Fix non-legacy ISO receive regressionJody McIntyre
Fix non-legacy multichannel ISO receive, broken by Parag Wardukar's allocation fix. Multichannel ISO receive still sucks; it should be possible to use both legacy and non-legacy modes at the same time, but with this patch, things are no worse than they were in 2.6.11 and allocation is still done at the correct time. Signed-off-by: Jody McIntyre <scjody@steamballoon.com> Signed-off-by: Linus Torvalds <torvalds@osdl.org>
2005-04-21[PATCH] ohci1394: tlabels misprinted in DBGMSGJody McIntyre
- Print the correct value in the DBGMSG in dma_rcv_tasklet(). See OHCI 1.1 section 8.7, page 103 ff. - Print tlabels as %d everywhere. Signed-off-by: Stefan Richter <stefanr@s5r6.in-berlin.de> Signed-off-by: Jody McIntyre <scjody@steamballoon.com> Signed-off-by: Linus Torvalds <torvalds@osdl.org>
2005-04-21Merge rsync://rsync.kernel.org/pub/scm/linux/kernel/git/aegl/linux-2.6.gitLinus Torvalds
2005-04-21[PATCH] alpha: key management syscallsRichard Henderson
Allocate syscall numbers for add_key, request_key, keyctl.
2005-04-21[IA64] fix fls()David Mosberger-Tang
The ia64-version of fls() never worked as intended (the bitnumbering was off by 1 and fls(0) was undefined). This patch fixes the problem by using a popcnt-based fls(), which on McKinley-derived cores is slightly faster than both ia64_fls() and generic_fls(). The resulting code, however, is bigger (7-8 bundles instead of about 3 bundles). Also switch ia64_popcnt() to __builtin_popcountl() for GCC v3.4 or newer since the compiler can predicate that and schedule it better. Thanks to Simon Derr and Matt Mackall for tracking down this bug. Signed-off-by: David Mosberger-Tang <davidm@hpl.hp.com> Signed-off-by: Tony Luck <tony.luck@intel.com>
2005-04-21[PATCH] fix for ISDN ippp filteringKarsten Keil
We do not longer use DLT_LINUX_SLL for activ/pass filters but DLT_PPP_WITHDIRECTION witch need 1 as outbound flag. Signed-off-by: Karsten Keil <kkeil@suse.de> Signed-off-by: Linus Torvalds <torvalds@osdl.org>
2005-04-21[PATCH] x86_64: Bug in new out of line put_user()Alexander Nyberg
The new out of line put_user() assembly on x86_64 changes %rcx without telling GCC about it causing things like: http://bugme.osdl.org/show_bug.cgi?id=4515 See to it that %rcx is not changed (made it consistent with get_user()). Signed-off-by: Alexander Nyberg <alexn@telia.com> Signed-off-by: ak@suse.de Signed-off-by: Linus Torvalds <torvalds@osdl.org>