| Age | Commit message (Collapse) | Author |
|---|
|
Hello,
I am not 100% sure this is the right thing to do, but it makes the
atmel-ssc driver happy on my at91rm9200 board.
This unifies the con_id across all at91 machines.
The atmel-ssc driver expects the con_id to be "pclk" or it will fail probing.
Signed-off-by: Joachim Eastwood <joachim.eastwood@jotron.com>
Signed-off-by: Jean-Christophe PLAGNIOL-VILLARD <plagnioj@jcrosoft.com>
|
|
Signed-off-by: Jean-Christophe PLAGNIOL-VILLARD <plagnioj@jcrosoft.com>
Acked-by: Nicolas Ferre <nicolas.ferre@atmel.com>
|
|
the atmel_ports is link to the console number and not the device id
this was not detected on at91 as we always register the dbgu on the console
as ttyS0
tested on at91sam9263 by setting the dbgu as ttyS1 and use as console
diff --git a/arch/arm/mach-at91/board-sam9263ek.c b/arch/arm/mach-at91/board-sam9263ek.c
index 70e5646..9b8a14f 100644
- a/arch/arm/mach-at91/board-sam9263ek.c
+ b/arch/arm/mach-at91/board-sam9263ek.c
@@ -58,14 +58,14 @@ static void __init ek_init_early(void)
/* Initialize processor: 16.367 MHz crystal */
at91_initialize(16367660);
- /* DBGU on ttyS0. (Rx & Tx only) */
- at91_register_uart(0, 0, 0);
+ /* DBGU on ttyS1. (Rx & Tx only) */
+ at91_register_uart(0, 1, 0);
- /* USART0 on ttyS1. (Rx, Tx, RTS, CTS) */
- at91_register_uart(AT91SAM9263_ID_US0, 1, ATMEL_UART_CTS | ATMEL_UART_RTS);
+ /* USART0 on ttyS0. (Rx, Tx, RTS, CTS) */
+ at91_register_uart(AT91SAM9263_ID_US0, 0, ATMEL_UART_CTS | ATMEL_UART_RTS);
- /* set serial console to ttyS0 (ie, DBGU) */
- at91_set_serial_console(0);
+ /* set serial console to ttyS1 (ie, DBGU) */
+ at91_set_serial_console(1);
}
/*
Signed-off-by: Jean-Christophe PLAGNIOL-VILLARD <plagnioj@jcrosoft.com>
Cc: Nicolas Ferre <nicolas.ferre@atmel.com>
Cc: Alan Cox <alan@linux.intel.com>
Cc: Hans-Christian Egtvedt <hans-christian.egtvedt@atmel.com>
|
|
Signed-off-by: Jean-Christophe PLAGNIOL-VILLARD <plagnioj@jcrosoft.com>
|
|
* 'for-linus' of git://git.kernel.dk/linux-block:
block: add REQ_SECURE to REQ_COMMON_MASK
block: use the passed in @bdev when claiming if partno is zero
block: Add __attribute__((format(printf...) and fix fallout
block: make disk_block_events() properly wait for work cancellation
block: remove non-syncing __disk_block_events() and fold it into disk_block_events()
block: don't use non-syncing event blocking in disk_check_events()
cfq-iosched: fix locking around ioc->ioc_data assignment
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/jgarzik/libata-dev
* 'upstream-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/jgarzik/libata-dev:
pata_marvell: Add support for 88SE91A0, 88SE91A4
libata/sas: only set FROZEN flag if new EH is supported
libata: apply NOSETXFER horkage to the affected Pioneer drives regardless of firmware revision
drivers/ata/sata_dwc_460ex: Fix typo 'corrresponding'
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/airlied/drm-2.6
* 'drm-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/airlied/drm-2.6:
drm/radeon/kms: handle special cases for vddc
drm/radeon/kms: fix num_banks tiling config for fusion
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/nab/scsi-post-merge-2.6
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/nab/scsi-post-merge-2.6:
tcm_fc: Fix conversion spec warning
tcm_fc: Fix possible lock to unlock type deadlock
tcm_fc: Fix ft_send_tm LUN lookup OOPs
target: Fix incorrect strlen() NULL terminator checks
target: Drop bogus ERR_PTR usage in target_fabric_configfs_init
target: Fix ERR_PTR dereferencing bugs
target: Convert transport_deregister_session_configfs nacl_sess_lock to save irq state
target: Fix transport_get_lun_for_tmr failure cases
[SCSI] target: Convert TASK_ATTR to scsi_tcq.h definitions
[SCSI] target: Convert REPORT_LUNs to use int_to_scsilun
[SCSI] target: Fix task->task_execute_queue=1 clear bug + LUN_RESET OOPs
[SCSI] target: Fix bug with task_sg chained transport_free_dev_tasks release
[SCSI] target: Fix interrupt context bug with stats_lock and core_tmr_alloc_req
[SCSI] target: Fix multi task->task_sg[] chaining logic bug
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/jbarnes/pci-2.6
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/jbarnes/pci-2.6:
x86/PCI/ACPI: fix type mismatch
PCI: fix new kernel-doc warning
PCI: Fix warning in drivers/pci/probe.c on sparc64
|
|
* git://git.kernel.org/pub/scm/linux/kernel/git/sfrench/cifs-2.6:
cifs: fix wsize negotiation to respect max buffer size and active signing (try #4)
CIFS: Fix problem with 3.0-rc1 null user mount failure
|
|
It was pointed out by 'make versioncheck' that some includes of
linux/version.h were not needed in fs/ (fs/btrfs/ctree.h and
fs/omfs/file.c).
This patch removes them.
Signed-off-by: Jesper Juhl <jj@chaosbits.net>
Acked-by: Bob Copeland <me@bobcopeland.com>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
|
|
This patch enables support for Marvell IDE PATA controllers found on
Asus P8P67LE motherboard.
The formatting has been corrected and I also received a report from two
users of this motherboard that the patch works.
Signed-off-by: Paweł Drewniak <czajernia@gmail.com>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
|
|
A voltage value of 0xff01 requires that the driver
look up the max voltage for the board based using the
atom SetVoltage command table.
Setting the proper voltage should fix stability on
some newer asics.
Signed-off-by: Alex Deucher <alexdeucher@gmail.com>
Signed-off-by: Dave Airlie <airlied@redhat.com>
|
|
The field is encoded:
0 = 4 banks
1 = 8 banks
2 = 16 banks
Signed-off-by: Alex Deucher <alexdeucher@gmail.com>
Signed-off-by: Dave Airlie <airlied@redhat.com>
|
|
This patch fixes the following conversion specification warning for size_t
drivers/target/tcm_fc/tfc_io.c: In function ‘ft_queue_data_in’:
drivers/target/tcm_fc/tfc_io.c:209: warning: format ‘%x’ expects type ‘unsigned int’, but argument 5 has type ‘size_t’
Reported-by: Randy Dunlap <randy.dunlap@oracle.com>
Reported-by: Stephen Rothwell <sfr@canb.auug.org.au>
Signed-off-by: Nicholas Bellinger <nab@linux-iscsi.org>
|
|
There is a typo here, it should be an unlock instead of a lock. The
original code will deadlock.
Signed-off-by: Dan Carpenter <error27@gmail.com>
Signed-off-by: Nicholas Bellinger <nab@linux-iscsi.org>
|
|
This patch fixes a bug in ft_send_tm() that was incorrectly calling
ft_get_lun_for_cmd() -> transport_get_lun_for_cmd(), instead of using
transport_get_lun_for_tmr() for the proper struct se_lun lookup
that was triggering an OOPs in the se_cmd->tmr_req failure path.
This patch fixes the issue by re-arranging the codepath where
transport_get_lun_for_tmr() is called after tmr request is allocated and
made it available as part of se_cmd.
It also drops the now unnecessary ft_get_lun_for_cmd() unpacking code, and
uses scsilun_to_int() directly ahead of transport_get_lun_for_cmd() and
transport_get_lun_for_tmr() usage.
Signed-off-by: Patil, Kiran <kiran.patil@intel.com>
Signed-off-by: Robert Love <robert.w.love@intel.com>
Signed-off-by: Nicholas A. Bellinger <nab@linux-iscsi.org>
|
|
This patch fixes a number of cases in target core using an incorrectly
if (strlen(foo) > SOME_MAX_SIZE)
As strlen() returns the number of characters in the string not counting
the NULL character at the end. So if you do something like:
char buf[10];
if (strlen("0123456789") > 10)
return -ETOOLONG;
snprintf(buf, 10, "0123456789");
printf("%s\n", buf);
then the last "9" gets chopped off and only "012345678" is printed.
Plus I threw in one small related cleanup.
Signed-off-by: Dan Carpenter <error27@gmail.com>
Signed-off-by: Nicholas Bellinger <nab@linux-iscsi.org>
|
|
In the original code, there were several places inside the
target_fabric_configfs_init() function that returned NULL on error
and one place the returned an ERR_PTR. There are two places that
call this function and they only check for NULL returns; they don't
check for ERR_PTRs. So I've changed the ERR_PTR so now the function
only returns NULL on error.
Signed-off-by: Dan Carpenter <error27@gmail.com>
Signed-off-by: Nicholas Bellinger <nab@linux-iscsi.org>
|
|
transport_init_session() and core_tmr_alloc_req() never return NULL,
they only return ERR_PTRs on error.
v2: Fix patch to return PTR_ERR(tl_nexus->se_sess) from Ankit Jain's
feedback.
Signed-off-by: Dan Carpenter <error27@gmail.com>
Signed-off-by: Ankit Jain <jankit@suse.de>
Signed-off-by: Nicholas Bellinger <nab@linux-iscsi.org>
|
|
irq state
This patch converts transport_deregister_session_configfs() to save/restore
spinlock IRQ state for struct se_node_acl->nacl_sess_lock access as tcm_qla2xxx
logic expects to call transport_deregister_session_configfs() code with
irq save already held for struct qla_hw_data.
Reported-by: Roland Dreier <roland@purestorage.com>
Signed-off-by: Nicholas Bellinger <nab@linux-iscsi.org>
|
|
This patch fixes two possible NULL pointer dereferences in target v4.0
code where se_tmr release path in core_tmr_release_req() can OOPs upon
transport_get_lun_for_tmr() failure by attempting to access se_device or
se_tmr->tmr_list without a valid member of se_device->tmr_list during
transport_free_se_cmd() release. This patch moves the se_tmr->tmr_dev
pointer assignment in transport_get_lun_for_tmr() until after possible
-ENODEV failures during unpacked_lun lookup.
This addresses an OOPs originally reported with LIO v4.1 upstream on
.39 code here:
TARGET_CORE[qla2xxx]: Detected NON_EXISTENT_LUN Access for 0x00000000
BUG: unable to handle kernel NULL pointer dereference at 0000000000000550
IP: [<ffffffff81035ec4>] __ticket_spin_trylock+0x4/0x20
PGD 0
Oops: 0000 [#1] SMP
last sysfs file: /sys/devices/system/cpu/cpu23/cache/index2/shared_cpu_map
CPU 1
Modules linked in: netconsole target_core_pscsi target_core_file
tcm_qla2xxx target_core_iblock tcm_loop target_core_mod configfs
ipmi_devintf ipmi_si ipmi_msghandler serio_raw i7core_edac ioatdma dca
edac_core ps_bdrv ses enclosure usbhid usb_storage ahci qla2xxx hid
uas e1000e mpt2sas libahci mlx4_core scsi_transport_fc
scsi_transport_sas raid_class scsi_tgt [last unloaded: netconsole]
Pid: 0, comm: kworker/0:0 Tainted: G W 2.6.39+ #1 Xyratex Storage Server
RIP: 0010:[<ffffffff81035ec4>] [<ffffffff81035ec4>]__ticket_spin_trylock+0x4/0x20
RSP: 0018:ffff88063e803c08 EFLAGS: 00010286
RAX: ffff880619ab45e0 RBX: 0000000000000550 RCX: 0000000000000000
RDX: 0000000000000000 RSI: 0000000000000000 RDI: 0000000000000550
RBP: ffff88063e803c08 R08: 0000000000000002 R09: 0000000000000000
R10: 0000000000000000 R11: 0000000000000001 R12: 0000000000000568
R13: 0000000000000001 R14: 0000000000000000 R15: ffff88060cd96a20
FS: 0000000000000000(0000) GS:ffff88063e800000(0000) knlGS:0000000000000000
CS: 0010 DS: 0000 ES: 0000 CR0: 000000008005003b
CR2: 0000000000000550 CR3: 0000000001a03000 CR4: 00000000000006e0
DR0: 0000000000000000 DR1: 0000000000000000 DR2: 0000000000000000
DR3: 0000000000000000 DR6: 00000000ffff0ff0 DR7: 0000000000000400
Process kworker/0:0 (pid: 0, threadinfo ffff880619ab8000, task ffff880619ab45e0)
Stack:
ffff88063e803c28 ffffffff812cf039 0000000000000550 0000000000000568
ffff88063e803c58 ffffffff8157071e ffffffffa028a1dc ffff88060f7e4600
0000000000000550 ffff880616961480 ffff88063e803c78 ffffffffa028a1dc
Call Trace:
<IRQ>
[<ffffffff812cf039>] do_raw_spin_trylock+0x19/0x50
[<ffffffff8157071e>] _raw_spin_lock+0x3e/0x70
[<ffffffffa028a1dc>] ? core_tmr_release_req+0x2c/0x60 [target_core_mod]
[<ffffffffa028a1dc>] core_tmr_release_req+0x2c/0x60 [target_core_mod]
[<ffffffffa028d0d2>] transport_free_se_cmd+0x22/0x50 [target_core_mod]
[<ffffffffa028d120>] transport_release_cmd_to_pool+0x20/0x40 [target_core_mod]
[<ffffffffa028e525>] transport_generic_free_cmd+0xa5/0xb0 [target_core_mod]
[<ffffffffa0147cc4>] tcm_qla2xxx_handle_tmr+0xc4/0xd0 [tcm_qla2xxx]
[<ffffffffa0191ba3>] __qla24xx_handle_abts+0xd3/0x150 [qla2xxx]
[<ffffffffa0197651>] qla_tgt_response_pkt+0x171/0x520 [qla2xxx]
[<ffffffffa0197a2d>] qla_tgt_response_pkt_all_vps+0x2d/0x220 [qla2xxx]
[<ffffffffa0171dd3>] qla24xx_process_response_queue+0x1a3/0x670 [qla2xxx]
[<ffffffffa0196281>] ? qla24xx_atio_pkt+0x81/0x120 [qla2xxx]
[<ffffffffa0174025>] ? qla24xx_msix_default+0x45/0x2a0 [qla2xxx]
[<ffffffffa0174198>] qla24xx_msix_default+0x1b8/0x2a0 [qla2xxx]
[<ffffffff810dadb4>] handle_irq_event_percpu+0x54/0x210
[<ffffffff810dafb8>] handle_irq_event+0x48/0x70
[<ffffffff810dd5ee>] ? handle_edge_irq+0x1e/0x110
[<ffffffff810dd647>] handle_edge_irq+0x77/0x110
[<ffffffff8100d362>] handle_irq+0x22/0x40
[<ffffffff8157b28d>] do_IRQ+0x5d/0xe0
[<ffffffff81571413>] common_interrupt+0x13/0x13
<EOI>
[<ffffffff813003f7>] ? intel_idle+0xd7/0x130
[<ffffffff813003f0>] ? intel_idle+0xd0/0x130
[<ffffffff8144832b>] cpuidle_idle_call+0xab/0x1c0
[<ffffffff8100a26b>] cpu_idle+0xab/0xf0
[<ffffffff81566c59>] start_secondary+0x1cb/0x1d2
Reported-by: Roland Dreier <roland@purestorage.com>
Signed-off-by: Nicholas Bellinger <nab@linux-iscsi.org>
|
|
On 16.06.2011 [08:28:39 -0500], Brian King wrote:
> On 06/16/2011 02:51 AM, Tejun Heo wrote:
> > On Wed, Jun 15, 2011 at 04:34:17PM -0700, Nishanth Aravamudan wrote:
> >>> That looks like the right thing to do. For ipr's usage of
> >>> libata, we don't have the concept of a port frozen state, so this flag
> >>> should really never get set. The alternate way to fix this would be to
> >>> only set ATA_PFLAG_FROZEN in ata_port_alloc if ap->ops->error_handler
> >>> is not NULL.
> >>
> >> It seemed like ipr is as you say, but I wasn't sure if it was
> >> appropriate to make the change above in the common libata-scis code or
> >> not. I don't want to break some other device on accident.
> >>
> >> Also, I tried your suggestion, but I don't think that can happen in
> >> ata_port_alloc? ata_port_alloc is allocated ap itself, and it seems like
> >> ap->ops typically gets set only after ata_port_alloc returns?
> >
> > Maybe we can test error_handler in ata_sas_port_start()?
>
> Good point. Since libsas is converted to the new eh now, we would need to have
> this test.
Commit 7b3a24c57d2eeda8dba9c205342b12689c4679f9 ("ahci: don't enable
port irq before handler is registered") caused a regression for CD-ROMs
attached to the IPR SATA bus on Power machines:
ata_port_alloc: ENTER
ata_port_probe: ata1: bus probe begin
ata1.00: ata_dev_read_id: ENTER
ata1.00: failed to IDENTIFY (I/O error, err_mask=0x40)
ata1.00: ata_dev_read_id: ENTER
ata1.00: failed to IDENTIFY (I/O error, err_mask=0x40)
ata1.00: limiting speed to UDMA7:PIO5
ata1.00: ata_dev_read_id: ENTER
ata1.00: failed to IDENTIFY (I/O error, err_mask=0x40)
ata1.00: disabled
ata_port_probe: ata1: bus probe end
scsi_alloc_sdev: Allocation failure during SCSI scanning, some SCSI devices might not be configured
The FROZEN flag added in that commit is only cleared by the new EH code,
which is not used by ipr. Clear this flag in the SAS code if we don't
support new EH.
Reported-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Signed-off-by: Nishanth Aravamudan <nacc@us.ibm.com>
Signed-off-by: Jeff Garzik <jgarzik@pobox.com>
|
|
regardless of firmware revision
It's unlikely NOSETXFER works for a revision of drive but doesn't for
another and pioneer doesn't seem to be fixing firmwares for the
affected drives. Apply NOSETXFER to the affected pioneer drives
regardless of firmware revision.
http://article.gmane.org/gmane.linux.ide/49734
Signed-off-by: Tejun Heo <tj@kernel.org>
Reported-by: fl-00@gmx.de
Signed-off-by: Jeff Garzik <jgarzik@pobox.com>
|
|
The patch below fixes a typo.
Signed-off-by: Justin P. Mattock <justinmattock@gmail.com>
Signed-off-by: Jeff Garzik <jgarzik@pobox.com>
|
|
for-linus
|
|
(try #4)
Hopefully last version. Base signing check on CAP_UNIX instead of
tcon->unix_ext, also clean up the comments a bit more.
According to Hongwei Sun's blog posting here:
http://blogs.msdn.com/b/openspecification/archive/2009/04/10/smb-maximum-transmit-buffer-size-and-performance-tuning.aspx
CAP_LARGE_WRITEX is ignored when signing is active. Also, the maximum
size for a write without CAP_LARGE_WRITEX should be the maxBuf that
the server sent in the NEGOTIATE request.
Fix the wsize negotiation to take this into account. While we're at it,
alter the other wsize definitions to use sizeof(WRITE_REQ) to allow for
slightly larger amounts of data to potentially be written per request.
Signed-off-by: Jeff Layton <jlayton@redhat.com>
Signed-off-by: Steve French <sfrench@us.ibm.com>
|
|
Secondary CPU bringup typically calls calibrate_delay() during its
initialization. However, calibrate_delay() modifies a global variable
(loops_per_jiffy) used for udelay() and __delay().
A side effect of 71c696b1 ("calibrate: extract fall-back calculation
into own helper") introduced in the 2.6.39 merge window means that we
end up with a substantial period where loops_per_jiffy is zero. This
causes the spinlock debugging code to malfunction:
u64 loops = loops_per_jiffy * HZ;
for (;;) {
for (i = 0; i < loops; i++) {
if (arch_spin_trylock(&lock->raw_lock))
return;
__delay(1);
}
...
}
by never calling arch_spin_trylock() - resulting in the CPU locking
up in an infinite loop inside __spin_lock_debug().
Work around this by only writing to loops_per_jiffy only once we have
completed all the calibration decisions.
Tested-by: Santosh Shilimkar <santosh.shilimkar@ti.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Cc: <stable@kernel.org> (2.6.39-stable)
--
Better solutions (such as omitting the calibration for secondary CPUs,
or arranging for calibrate_delay() to return the LPJ value and leave
it to the caller to decide where to store it) are a possibility, but
would be much more invasive into each architecture.
I think this is the best solution for -rc and stable, but it should be
revisited for the next merge window.
init/calibrate.c | 14 ++++++++------
1 files changed, 8 insertions(+), 6 deletions(-)
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
|
|
The driver went to initialize its waitqueue at the start of the main
processing thread. However, it is possible that this thread is not
scheduled on a CPU before the write function is called which leads to a
following error:
BUG: spinlock bad magic on CPU#1, swapper/1
lock: f5f3ebdc, .magic: 00000000, .owner: <none>/-1, .owner_cpu: 0
Pid: 1, comm: swapper Not tainted 3.0.0-rc2+ #67
Call Trace:
[<c1289663>] spin_bug+0xa3/0xf0
[<c12897ad>] do_raw_spin_lock+0x7d/0x150
[<c14963de>] _raw_spin_lock_irqsave+0x4e/0x60
[<c102f2bb>] __wake_up+0x1b/0x50
[<c12d3715>] serial_m3110_con_write+0x55/0x60
[<c1041575>] __call_console_drivers+0x75/0x90
[<c10415d9>] _call_console_drivers+0x49/0x80
[<c1041baa>] console_unlock+0xca/0x1f0
[<c10420ef>] vprintk+0x18f/0x4f0
[<c14928a3>] printk+0x18/0x1a
[<c1042730>] register_console+0x2e0/0x350
[<c12d098e>] uart_add_one_port+0x33e/0x3d0
[<c1485ba6>] serial_m3110_probe+0x1c2/0x1df
[<c1303db7>] spi_drv_probe+0x17/0x20
...
Fix this by initializing the waitqueue before the main thread is
created.
Signed-off-by: Mika Westerberg <mika.westerberg@linux.intel.com>
Signed-off-by: Alan Cox <alan@linux.intel.com>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
|
|
Change print message to notice instead of error to clean up non critical
messages showing on startup. The MAX3111 not being present is a normal
path for end user systems.
Signed-off-by: William Douglas <william.douglas@intel.com>
[rebased on 3.0, switched to dev_dbg()]
Signed-off-by: Alan Cox <alan@linux.intel.com>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/shaggy/jfs-2.6
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/shaggy/jfs-2.6:
jfs: agstart field must be 64 bits
JFS: Don't save agno in the inode
jfs: Update agstart when resizing volume
jfs: old_agsize should be 64 bits in jfs_extendfs
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/rafael/suspend-2.6
* 'pm-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/rafael/suspend-2.6:
PCI / PM: Block races between runtime PM and system sleep
PM / Domains: Update documentation
PM / Runtime: Handle clocks correctly if CONFIG_PM_RUNTIME is unset
PM: Fix async resume following suspend failure
PM: Free memory bitmaps if opening /dev/snapshot fails
PM: Rename dev_pm_info.in_suspend to is_prepared
PM: Update documentation regarding sysdevs
PM / Runtime: Update doc: usage count no longer incremented across system PM
|
|
Commit 959ecc48fc75 ("mm/memory_hotplug.c: fix building of node hotplug
zonelist") does not protect the build_all_zonelists() call with
zonelists_mutex as needed. This can lead to races in constructing
zonelist ordering if a concurrent build is underway. Protecting this
with lock_memory_hotplug() is insufficient since zonelists can be
rebuild though sysfs as well.
Signed-off-by: David Rientjes <rientjes@google.com>
Reviewed-by: KOSAKI Motohiro <kosaki.motohiro@jp.fujitsu.com>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
|
|
The error handling in mem_online_node() is incorrect: hotadd_new_pgdat()
returns NULL if the new pgdat could not have been allocated and a pointer
to it otherwise.
mem_online_node() should fail if hotadd_new_pgdat() fails, not the
inverse. This fixes an issue when memoryless nodes are not onlined and
their sysfs interface is not registered when their first cpu is brought
up.
The bug was introduced by commit cf23422b9d76 ("cpu/mem hotplug: enable
CPUs online before local memory online") iow v2.6.35.
Signed-off-by: David Rientjes <rientjes@google.com>
Reviewed-by: KOSAKI Motohiro <kosaki.motohiro@jp.fujitsu.com>
Cc: stable@kernel.org
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
|
|
Figured it out: it was broken by b946845a9dc523c759cae2b6a0f6827486c3221a commit - "cifs: cifs_parse_mount_options: do not tokenize mount options in-place". So, as a quick fix I suggest to apply this patch.
[PATCH] CIFS: Fix kfree() with constant string in a null user case
Signed-off-by: Pavel Shilovsky <piastryyy@gmail.com>
Reviewed-by: Jeff Layton <jlayton@redhat.com>
Signed-off-by: Steve French <sfrench@us.ibm.com>
|
|
Fix error handling in construct_key_and_link().
If construct_alloc_key() returns an error, it shouldn't pass out through
the normal path as the key_serial() called by the kleave() statement
will oops when it gets an error code in the pointer:
BUG: unable to handle kernel paging request at ffffffffffffff84
IP: [<ffffffff8120b401>] request_key_and_link+0x4d7/0x52f
..
Call Trace:
[<ffffffff8120b52c>] request_key+0x41/0x75
[<ffffffffa00ed6e8>] cifs_get_spnego_key+0x206/0x226 [cifs]
[<ffffffffa00eb0c9>] CIFS_SessSetup+0x511/0x1234 [cifs]
[<ffffffffa00d9799>] cifs_setup_session+0x90/0x1ae [cifs]
[<ffffffffa00d9c02>] cifs_get_smb_ses+0x34b/0x40f [cifs]
[<ffffffffa00d9e05>] cifs_mount+0x13f/0x504 [cifs]
[<ffffffffa00caabb>] cifs_do_mount+0xc4/0x672 [cifs]
[<ffffffff8113ae8c>] mount_fs+0x69/0x155
[<ffffffff8114ff0e>] vfs_kern_mount+0x63/0xa0
[<ffffffff81150be2>] do_kern_mount+0x4d/0xdf
[<ffffffff81152278>] do_mount+0x63c/0x69f
[<ffffffff8115255c>] sys_mount+0x88/0xc2
[<ffffffff814fbdc2>] system_call_fastpath+0x16/0x1b
Signed-off-by: David Howells <dhowells@redhat.com>
Acked-by: Jeff Layton <jlayton@redhat.com>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
|
|
MN10300's asm/uaccess.h needs to #include linux/kernel.h to get might_sleep()
otherwise it fails to build on MN10300 allyesconfig. This fails in a few
places with messages like the following:
In file included from security/keys/trusted.c:14:
include/linux/uaccess.h: In function '__copy_from_user_nocache':
include/linux/uaccess.h:52: error: implicit declaration of function 'might_sleep'
Signed-off-by: David Howells <dhowells@redhat.com>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
|
|
* 'bugfixes' of git://git.linux-nfs.org/projects/trondmy/nfs-2.6:
NFS: Fix decode_secinfo_maxsz
NFSv4.1: Fix an off-by-one error in pnfs_generic_pg_test
NFSv4.1: Fix some issues with pnfs_generic_pg_test
NFSv4.1: file layout must consider pg_bsize for coalescing
pnfs-obj: No longer needed to take an extra ref at add_device
SUNRPC: Ensure the RPC client only quits on fatal signals
NFSv4: Fix a readdir regression
nfs4.1: mark layout as bad on error path in _pnfs_return_layout
nfs4.1: prevent race that allowed use of freed layout in _pnfs_return_layout
NFSv4.1: need to put_layout_hdr on _pnfs_return_layout error path
NFS: (d)printks should use %zd for ssize_t arguments
NFSv4.1: fix break condition in pnfs_find_lseg
nfs4.1: fix several problems with _pnfs_return_layout
NFSv4.1: allow zero fh array in filelayout decode layout
NFSv4.1: allow nfs_fhget to succeed with mounted on fileid
NFSv4.1: Fix a refcounting issue in the pNFS device id cache
NFSv4.1: deprecate headerpadsz in CREATE_SESSION
NFS41: do not update isize if inode needs layoutcommit
NLM: Don't hang forever on NLM unlock requests
NFS: fix umount of pnfs filesystems
|
|
After commit e8665002477f0278f84f898145b1f141ba26ee26
(PM: Allow pm_runtime_suspend() to succeed during system suspend) it
is possible that a device resumed by the pm_runtime_resume(dev) in
pci_pm_prepare() will be suspended immediately from a work item,
timer function or otherwise, defeating the very purpose of calling
pm_runtime_resume(dev) from there. To prevent that from happening
it is necessary to increment the runtime PM usage counter of the
device by replacing pm_runtime_resume() with pm_runtime_get_sync().
Moreover, the incremented runtime PM usage counter has to be
decremented by the corresponding pci_pm_complete(), via
pm_runtime_put_sync().
Signed-off-by: Rafael J. Wysocki <rjw@sisk.pl>
Cc: stable@kernel.org
Acked-by: Jesse Barnes <jbarnes@virtuousgeek.org>
|
|
Commit 4d27e9dcff00a6425d779b065ec8892e4f391661 (PM: Make power
domain callbacks take precedence over subsystem ones) forgot to
update the device power management documentation to take changes
made by it into account. Correct that mistake.
Signed-off-by: Rafael J. Wysocki <rjw@sisk.pl>
|
|
Commit 85eb8c8d0b0900c073b0e6f89979ac9c439ade1a (PM / Runtime:
Generic clock manipulation rountines for runtime PM (v6)) converted
the shmobile platform to using generic code for runtime PM clock
management, but it changed the behavior for CONFIG_PM_RUNTIME unset
incorrectly.
Specifically, for CONFIG_PM_RUNTIME unset pm_runtime_clk_notify()
should enable clocks for action equal to BUS_NOTIFY_BIND_DRIVER and
it should disable them for action equal to BUS_NOTIFY_UNBOUND_DRIVER
(instead of BUS_NOTIFY_ADD_DEVICE and BUS_NOTIFY_DEL_DEVICE,
respectively). Make this function behave as appropriate.
Signed-off-by: Rafael J. Wysocki <rjw@sisk.pl>
Acked-by: Magnus Damm <damm@opensource.se>
|
|
The PM core doesn't handle suspend failures correctly when it comes to
asynchronously suspended devices. These devices are moved onto the
dpm_suspended_list as soon as the corresponding async thread is
started up, and they remain on the list even if they fail to suspend
or the sleep transition is cancelled before they get suspended. As a
result, when the PM core unwinds the transition, it tries to resume
the devices even though they were never suspended.
This patch (as1474) fixes the problem by adding a new "is_suspended"
flag to dev_pm_info. Devices are resumed only if the flag is set.
[rjw:
* Moved the dev->power.is_suspended check into device_resume(),
because we need to complete dev->power.completion and clear
dev->power.is_prepared too for devices whose
dev->power.is_suspended flags are unset.
* Fixed __device_suspend() to avoid setting dev->power.is_suspended
if async_error is different from zero.]
Signed-off-by: Alan Stern <stern@rowland.harvard.edu>
Signed-off-by: Rafael J. Wysocki <rjw@sisk.pl>
Cc: stable@kernel.org
|
|
When opening /dev/snapshot device, snapshot_open() creates memory
bitmaps which are freed in snapshot_release(). But if any of the
callbacks called by pm_notifier_call_chain() returns NOTIFY_BAD, open()
fails, snapshot_release() is never called and bitmaps are not freed.
Next attempt to open /dev/snapshot then triggers BUG_ON() check in
create_basic_memory_bitmaps(). This happens e.g. when vmwatchdog module
is active on s390x.
Signed-off-by: Michal Kubecek <mkubecek@suse.cz>
Signed-off-by: Rafael J. Wysocki <rjw@sisk.pl>
Cc: stable@kernel.org
|
|
This patch (as1473) renames the "in_suspend" field in struct
dev_pm_info to "is_prepared", in preparation for an upcoming change.
The new name is more descriptive of what the field really means.
Signed-off-by: Alan Stern <stern@rowland.harvard.edu>
Signed-off-by: Rafael J. Wysocki <rjw@sisk.pl>
Cc: stable@kernel.org
|
|
The part of Documentation/power/devices.txt regarding sysdevs is not
valid any more after commit 2e711c04dbbf7a7732a3f7073b1fc285d12b369d
(PM: Remove sysdev suspend, resume and shutdown operations), so
remove it.
Signed-off-by: Rafael J. Wysocki <rjw@sisk.pl>
|
|
Commit e8665002477f0278f84f898145b1f141ba26ee26 (PM: Allow
pm_runtime_suspend() to succeed during system suspend) removed usage
count increment across system PM.
Update doc to reflect this.
Signed-off-by: Kevin Hilman <khilman@ti.com>
Signed-off-by: Rafael J. Wysocki <rjw@sisk.pl>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/roland/infiniband
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/roland/infiniband:
IB/qib: Ensure that LOS and DFE are being turned off
RDMA/cxgb4: Couple of abort fixes
RDMA/cxgb4: Don't truncate MR lengths
RDMA/cxgb4: Don't exceed hw IQ depth limit for user CQs
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/tytso/ext4
* 'for_linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tytso/ext4:
jbd2: Fix oops in jbd2_journal_remove_journal_head()
jbd2: Remove obsolete parameters in the comments for some jbd2 functions
ext4: fixed tracepoints cleanup
ext4: use FIEMAP_EXTENT_LAST flag for last extent in fiemap
ext4: Fix max file size and logical block counting of extent format file
ext4: correct comments for ext4_free_blocks()
|
|
I initially did the calculation in bytes, and not words
Signed-off-by: Bryan Schumaker <bjschuma@netapp.com>
Signed-off-by: Trond Myklebust <Trond.Myklebust@netapp.com>
|
|
And document what is going on there...
Signed-off-by: Trond Myklebust <Trond.Myklebust@netapp.com>
|
