| Age | Commit message (Collapse) | Author |
|---|
|
Commit 653241 (net: RFC3069, private VLAN proxy arp support) changed
the behavior of arp proxy to send arp replies back out on the interface
the request came in even if the private VLAN feature is disabled.
Previously we checked rt->dst.dev != skb->dev for in scenarios, when
proxy arp is enabled on for the netdevice and also when individual proxy
neighbour entries have been added.
This patch adds the check back for the pneigh_lookup() scenario.
Signed-off-by: Thomas Graf <tgraf@suug.ch>
Acked-by: Jesper Dangaard Brouer <hawk@comx.dk>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
This patch fix a bug which introduced by commit ac8a4810 (ipv4: Save
nexthop address of LSRR/SSRR option to IPCB.).In that patch, we saved
the nexthop of SRR in ip_option->nexthop and update iph->daddr until
we get to ip_forward_options(), but we need to update it before
ip_rt_get_source(), otherwise we may get a wrong src.
Signed-off-by: Li Wei <lw@cn.fujitsu.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
When the netprio_cgroup module is not loaded, net_prio_subsys_id
is -1, and so sock_update_prioidx() accesses cgroup_subsys array
with negative index subsys[-1].
Make the code resembles cls_cgroup code, which is bug free.
Origionally-authored-by: Li Zefan <lizf@cn.fujitsu.com>
Signed-off-by: Li Zefan <lizf@cn.fujitsu.com>
Signed-off-by: Neil Horman <nhorman@tuxdriver.com>
CC: "David S. Miller" <davem@davemloft.net>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
So we delay the allocation till the priority is set through cgroup,
and this makes skb_update_priority() faster when it's not set.
This also eliminates an off-by-one bug similar with the one fixed
in the previous patch.
Origionally-authored-by: Li Zefan <lizf@cn.fujitsu.com>
Signed-off-by: Li Zefan <lizf@cn.fujitsu.com>
Signed-off-by: Neil Horman <nhorman@tuxdriver.com>
CC: "David S. Miller" <davem@davemloft.net>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
# mount -t cgroup xxx /mnt
# mkdir /mnt/tmp
# cat /mnt/tmp/net_prio.ifpriomap
lo 0
eth0 0
virbr0 0
# echo 'lo 999' > /mnt/tmp/net_prio.ifpriomap
# cat /mnt/tmp/net_prio.ifpriomap
lo 999
eth0 0
virbr0 4101267344
We got weired output, because we exceeded the boundary of the array.
We may even crash the kernel..
Origionally-authored-by: Li Zefan <lizf@cn.fujitsu.com>
Signed-off-by: Li Zefan <lizf@cn.fujitsu.com>
Signed-off-by: Neil Horman <nhorman@tuxdriver.com>
CC: "David S. Miller" <davem@davemloft.net>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
The current error handling doesn't work because we flash_part is a u32
so the checks for negative error codes don't work. I considered making
things signed but I don't know the hardware enough to say if that's a
problem. Really, we don't use the error codes so just returning zero
for all problems is fine.
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
We use len to store the return value from eth_header(). eth_header()
can return -ETH_HLEN (-14). We want to pass this back instead of
truncating it to 65522 and returning that.
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Acked-by: Neil Horman <nhorman@tuxdriver.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Just like skb->cb[], so that qdisc_skb_cb can be encapsulated inside
of other data structures.
This is intended to be used by IPoIB so that it can remember
addressing information stored at hard_header_ops->create() time that
it can fetch when the packet gets to the transmit routine.
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
If the number of tx/rx queues changes the ethtool ioctl
ETHTOOL_GSTATS may overrun the userspace buffer. This
occurs because the general practice in user space to
query stats is to issue a ETHTOOL_GSSET cmd to learn the
buffer size needed, allocate the buffer, then call
ETHTOOL_GSTIRNGS and ETHTOOL_GSTATS. If the number of
real_num_queues is changed or flow control attributes
are changed after ETHTOOL_GSSET but before the
ETHTOOL_GSTRINGS/ETHTOOL_GSTATS a user space buffer
overrun occurs.
To fix the overrun always return the max buffer size
needed from get_sset_count() then return all strings
and stats from get_strings()/get_ethtool_stats().
This _will_ change the output from the ioctl() call
which could break applications and script parsing in
theory. I believe these changes should not break existing
tools because the only changes will be more {tx|rx}_queues
and the {tx|rx}_pb_* stats will always be returned.
Existing scripts already need to handle changing number
of queues because this occurs today depending on system
and current features. The {tx|rx}_pb_* stats are at the
end of the output and should be handled by scripts today
regardless.
Finally get_ethtool_stats and get_strings are free-form
outputs tools parsing these outputs should be defensive
anyways. In the end these updates are better then
having a tool segfault because of a buffer overrun.
Signed-off-by: John Fastabend <john.r.fastabend@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
|
|
Users expect the up2tc mapping to be maintained across a DCB
enable/disable/enable transition. And since we maintain all
the other DCB attributes we should do this for up2tc mappings
as well just to be consistent. Also without this we break
user space applications that expect this to occur that
previously worked.
Signed-off-by: John Fastabend <john.r.fastabend@intel.com>
Tested-by: Stephen Ko <stephen.s.ko@intel.com>
Tested-by: Ross Brattain <ross.b.brattain@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
|
|
If the netdev is already in NETREG_UNREGISTERING/_UNREGISTERED state, do not
update the real num tx queues. netdev_queue_update_kobjects() is already
called via remove_queue_kobjects() at NETREG_UNREGISTERING time. So, when
upper layer driver, e.g., FCoE protocol stack is monitoring the netdev
event of NETDEV_UNREGISTER and calls back to LLD ndo_fcoe_disable() to remove
extra queues allocated for FCoE, the associated txq sysfs kobjects are already
removed, and trying to update the real num queues would cause something like
below:
...
PID: 25138 TASK: ffff88021e64c440 CPU: 3 COMMAND: "kworker/3:3"
#0 [ffff88021f007760] machine_kexec at ffffffff810226d9
#1 [ffff88021f0077d0] crash_kexec at ffffffff81089d2d
#2 [ffff88021f0078a0] oops_end at ffffffff813bca78
#3 [ffff88021f0078d0] no_context at ffffffff81029e72
#4 [ffff88021f007920] __bad_area_nosemaphore at ffffffff8102a155
#5 [ffff88021f0079f0] bad_area_nosemaphore at ffffffff8102a23e
#6 [ffff88021f007a00] do_page_fault at ffffffff813bf32e
#7 [ffff88021f007b10] page_fault at ffffffff813bc045
[exception RIP: sysfs_find_dirent+17]
RIP: ffffffff81178611 RSP: ffff88021f007bc0 RFLAGS: 00010246
RAX: ffff88021e64c440 RBX: ffffffff8156cc63 RCX: 0000000000000004
RDX: ffffffff8156cc63 RSI: 0000000000000000 RDI: 0000000000000000
RBP: ffff88021f007be0 R8: 0000000000000004 R9: 0000000000000008
R10: ffffffff816fed00 R11: 0000000000000004 R12: 0000000000000000
R13: ffffffff8156cc63 R14: 0000000000000000 R15: ffff8802222a0000
ORIG_RAX: ffffffffffffffff CS: 0010 SS: 0018
#8 [ffff88021f007be8] sysfs_get_dirent at ffffffff81178c07
#9 [ffff88021f007c18] sysfs_remove_group at ffffffff8117ac27
#10 [ffff88021f007c48] netdev_queue_update_kobjects at ffffffff813178f9
#11 [ffff88021f007c88] netif_set_real_num_tx_queues at ffffffff81303e38
#12 [ffff88021f007cc8] ixgbe_set_num_queues at ffffffffa0249763 [ixgbe]
#13 [ffff88021f007cf8] ixgbe_init_interrupt_scheme at ffffffffa024ea89 [ixgbe]
#14 [ffff88021f007d48] ixgbe_fcoe_disable at ffffffffa0267113 [ixgbe]
#15 [ffff88021f007d68] vlan_dev_fcoe_disable at ffffffffa014fef5 [8021q]
#16 [ffff88021f007d78] fcoe_interface_cleanup at ffffffffa02b7dfd [fcoe]
#17 [ffff88021f007df8] fcoe_destroy_work at ffffffffa02b7f08 [fcoe]
#18 [ffff88021f007e18] process_one_work at ffffffff8105d7ca
#19 [ffff88021f007e68] worker_thread at ffffffff81060513
#20 [ffff88021f007ee8] kthread at ffffffff810648b6
#21 [ffff88021f007f48] kernel_thread_helper at ffffffff813c40f4
Signed-off-by: Yi Zou <yi.zou@intel.com>
Tested-by: Ross Brattain <ross.b.brattain@intel.com>
Tested-by: Stephen Ko <stephen.s.ko@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
|
|
This patch fixes an issue in which RSC will generate corrupted frames when
PAGE_SIZE is larger than 8K. Specifically it looks like that in 2.6.39 a
change was made so that GRO would always have at least 16 frags available
for coalescing, but the ixgbe RSC logic was not updated. As such the RSC
feature would generate a frame larger than 64K and then overflow the value
in the IP length field.
To correct that I am now basing things on the PAGE_SIZE.
Signed-off-by: Alexander Duyck <alexander.h.duyck@intel.com>
Tested-by: Stephen Ko <stephen.s.ko@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
|
|
A check for the number of VFs allocated should have used a greater than
equal operator instead of just greater than. This caused allocation of
exactly 32 VFs to not enable the PF transmit and receive enables.
Signed-off-by: Greg Rose <gregory.v.rose@intel.com>
Tested-by: Robert E Garrett <robertX.e.garrett@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
|
|
Recent addition of code to find already allocated VFs failed to take
account that systems with 2 or more multi-port SR-IOV capable controllers
might have already enabled VFs. Make sure that the VFs the function is
finding are actually subordinate to the particular instance of the adapter
that is looking for them and not subordinate to some device that has
previously enabled SR-IOV.
This bug exists in 3.2 stable as well as 3.3 release candidates.
CC: stable@vger.kernel.org
Reported-by: David Ahern <daahern@cisco.com>
Signed-off-by: Greg Rose <gregory.v.rose@intel.com>
Tested-by: Robert E Garrett <robertX.e.garrett@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
|
|
Recent addition of code to find already allocated VFs failed to take
account that systems with 2 or more multi-port SR-IOV capable controllers
might have already enabled VFs. Make sure that the VFs the function is
finding are actually subordinate to the particular instance of the adapter
that is looking for them and not subordinate to some device that has
previously enabled SR-IOV.
This is applicable to 3.2+ kernels.
CC: stable@vger.kernel.org
Reported-by: David Ahern <daahern@cisco.com>
Signed-off-by: Greg Rose <gregory.v.rose@intel.com>
Tested-by: Robert E Garrett <robertX.e.garrett@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
|
|
Commit d5bc77a223b0e9b9dfb002048d2b34a79e7d0b48 broke Wake-on-LAN by
inadvertently dropping the enabling of DMA receives.
Restore the enabling of DMA receives for WoL.
This is applicable to 3.1+ stable trees.
CC: stable@vger.stable.org
Reported-by: Tobias Klausmann <klausman@schwarzvogel.de>
Signed-off-by: Dean Nelson <dnelson@redhat.com>
Tested-by: Tobias Klausmann <klausman@schwarzvogel.de>
Tested-by: Aaron Brown <aaron.f.brown@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/linville/wireless
|
|
Shlomo Pongratz reported GRO L2 header check was suited for Ethernet
only, and failed on IB/ipoib traffic.
He provided a patch faking a zeroed header to let GRO aggregates frames.
Roland Dreier, Herbert Xu, and others suggested we change GRO L2 header
check to be more generic, ie not assuming L2 header is 14 bytes, but
taking into account hard_header_len.
__napi_gro_receive() has special handling for the common case (Ethernet)
to avoid a memcmp() call and use an inline optimized function instead.
Signed-off-by: Eric Dumazet <eric.dumazet@gmail.com>
Reported-by: Shlomo Pongratz <shlomop@mellanox.com>
Cc: Roland Dreier <roland@kernel.org>
Cc: Or Gerlitz <ogerlitz@mellanox.com>
Cc: Herbert Xu <herbert@gondor.apana.org.au>
Tested-by: Sean Hefty <sean.hefty@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Commit a0417fa3a18a ("net: Make qdisc_skb_cb upper size bound
explicit.") made it possible for a netdev driver to use skb->cb
between its header_ops.create method and its .ndo_start_xmit
method. Use this in ipoib_hard_header() to stash away the LL address
(GID + QPN), instead of the "ipoib_pseudoheader" hack. This allows
IPoIB to stop lying about its hard_header_len, which will let us fix
the L2 check for GRO.
Signed-off-by: Roland Dreier <roland@purestorage.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/linville/wireless into for-davem
|
|
Some devices (iwl5100) cannot connect to zd1211rw based AP. It appears that
zd1211 firmware messes up duration_id field if it is not set to zero by driver.
Sniffing traffic shows that zd1211 is transmitting frames with duration_id bits
14 and 15 set and other bits appearing random. Setting duration_id at driver to
zero results zd1211 outputting sane duration_id. This means that firmware is
setting correct values itself and expects duration_id to be zero in first
place.
Looking at vendor driver shows that only PSPoll frames have duration_id set by
driver, for other frames duration_id left zero.
Original bug-report and attached patch at:
http://sourceforge.net/mailarchive/message.php?msg_id=28759111
Reported-by: Tomas Vanek <Tomas.Vanek@fbl.cz>
[modified original patch from bug-report, added check for pspoll frame]
Signed-off-by: Jussi Kivilinna <jussi.kivilinna@mbnet.fi>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
|
|
8<----------------------------------------------------------------------
From: Ralf Roesch <ralf.roesch@rw-gmbh.de>
Date: Wed, 16 Nov 2011 09:33:50 +0100
Subject: [PATCH] net: enable TC35815 for MIPS again
TX493[8,9] MIPS SoCs support 2 Ethernet channels of type TC35815
which are connected to the internal PCI controller.
And JMR3927 MIPS board has a TC35815 chip on board.
These dependencies were lost on movement to drivers/net/ethernet/toshiba.
Signed-off-by: Ralf Roesch <ralf.roesch@rw-gmbh.de>
Signed-off-by: Atsushi Nemoto <anemo@mba.ocn.ne.jp>
CC: stable@vger.kernel.org [3.2+]
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
When this GETHER controller received a large frame (about 1800 bytes
or more), skb_over_panic() happened. This is because the previous
driver set the RFLR to 0x1000 (4096 bytes) and the skb allocate size
is smaller than 4096 bytes. So, the controller accepted such a frame.
The controller can discard a large frame by the RFLR setting.
So, the patch modifies the value of RFLR to mtu + ETH_HLEN +
VLAN_HLEN + ETH_FCS_LEN.
Signed-off-by: Yoshihiro Shimoda <yoshihiro.shimoda.uh@renesas.com>
Cc: Eric Dumazet <eric.dumazet@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Tested-by: Anisse Astier <anisse@astier.eu>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
We allocate memory for 'new_data' with kmalloc(). If we get the memory
we then try to build_skb() and if that should fail (which it can) we
do not enter 'if (likely(skb)) {' and actually use 'new_data' but
instead fall through to the 'drop:' label and end up returning from
the function without ever assigning 'new'data' to anything or freeing
it. That leaks the memory allocated to 'new_data'.
This patch fixes the memory leak by doing a kfree(new_data) in the
case where build_skb() fails (or where allocation of 'new_data' itself
fails, but in taht case it's just a harmless kfree(NULL)).
Signed-off-by: Jesper Juhl <jj@chaosbits.net>
Acked-by: Eric Dumazet <eric.dumazet@gmail.com>
Acked-by: Eilon Greenstein <eilong@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
As it is, with PCI/ISA/MCA/CCW all set to n and PCMCIA set to m
setting TR to y will set LLC to m, with very unpleasant results -
net/802/psnap gets picked into obj-y, resulting in the kernel
that won't link - psnap calls functions from llc. The cause,
AFAICS, is that kconfig gets rev_dep for LLC containing
|| TR && (deps for TR)
and even though TR is boolean, both LLC and PCMCIA are tristate
and that thing becomes || y && (n || m), i.e. || m. The reason
for dependency on PCMCIA is that when none of PCI, ISA, MCA, CCW
or PCMCIA is set there'll be no tokenring drivers, so there's no
point building tokenring core. Proper fix probably belongs in
kconfig (we need strict and, such that y <strict_and> m would be
y, so that rev_deps added for tristate selected by bool would
use that instead of &&; we'd have || TR <strict_and> (deps for TR)
in this case), but it's a rather intrusive change. There's an
easy workaround in case of TR -> LLC select, namely to have a def_bool y
symbol sitting under if TR and have that symbol selecting LLC.
Kudos to johill for suggesting that one...
Signed-off-by: Al Viro <viro@zeniv.linux.org.uk>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
As reported by several people...
The code in rx_clean was panic'ing so revert
commit d0249e44432aa0ffcf710b64449b8eaa3722547e.
Will redo DMA mapping checks as new patches for a later release.
Signed-off-by: Stephen Hemminger <shemminger@vyatta.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
mlx4_en_prepare_rx_desc does not correctly clean up after it finds an
allocation failure. It should unmap a page before calling put_page, but
it only calls the later.
This bug would prevent a device removal using hotplug after setting the
device MTU to 9000 and opening the network interface. After the fix, we
still see the allocation failure with MTU 9000, but we are able to
remove the device.
Signed-off-by: Thadeu Lima de Souza Cascardo <cascardo@linux.vnet.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
After opening the network interface, Mellanox ConnectX device cannot be
removed by hotplug because it has not properly unmapped all DMA memory.
It happens that mlx4_en_activate_rx_rings overrides the variable that
keeps the size of the memory mapped.
This is fixed by passing to mlx4_en_destroy_rx_ring the same size that is
given to mlx4_en_create_rx_ring.
After applying this patch, hot unplugging the device works after opening
the interface.
Signed-off-by: Thadeu Lima de Souza Cascardo <cascardo@linux.vnet.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
The brcmsmac driver is now using the bcma SPROM CRC check, which does
not recognize all chipsets that were functional prior to the switch. In
particular, the current code bails out on odd CRC errors in recent
Macbooks. This patch ignores those errors, with the argument that an
unrecognized SPROM should be treated similarly to a non-existing one.
Signed-off-by: Henrik Rydberg <rydberg@euromail.se>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
|
|
Use port number for correct steering (list per port).
Before the fix all steering entries (for both physical ports)
were managed in first port structures, so we had leakage of resources
for port 2.
Signed-off-by: Eugenia Emantayev <eugenia@mellanox.co.il>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Use MLX4_DEV_CAP_FLAG_VEP_UC_STEER for unicast_promisc_add/remove
Unicast entries were managed in wrong data structures.
Signed-off-by: Eugenia Emantayev <eugenia@mellanox.co.il>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Perform cleanup also in non-master flow.
The VFs use communication channel as well.
Signed-off-by: Eugenia Emantayev <eugenia@mellanox.co.il>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
commit adb5066 "ath9k_hw: do not apply the 2.4 ghz ack timeout
workaround to cts" reduced the hardware CTS timeout to the normal
values specified by the standard, but it turns out while it doesn't
need the same extra time that it needs for the ACK timeout, it
does need more than the value specified in the standard, but only
for 2.4 GHz.
This patch brings the CTS timeout value in sync with the initialization
values, while still allowing adjustment for bigger distances.
Signed-off-by: Felix Fietkau <nbd@openwrt.org>
Cc: stable@vger.kernel.org
Reported-by: Seth Forshee <seth.forshee@canonical.com>
Reported-by: Marek Lindner <lindner_marek@yahoo.de>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
|
|
commit b4a82a0 "ath9k_hw: fix interpretation of the rx KeyMiss flag"
fixed the interpretation of the KeyMiss flag for keycache based lookups,
however WEP encryption uses a static index, so KeyMiss is always asserted
for it, even though frames are decrypted properly.
Fix this by clearing the ATH9K_RXERR_KEYMISS flag if no keycache based
lookup was performed.
Signed-off-by: Felix Fietkau <nbd@openwrt.org>
Cc: stable@vger.kernel.org
Reported-by: Laurent Bonnans <bonnans.l@gmail.com>
Reported-by: Jurica Vukadin <u.ra604@googlemail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
|
|
If driver load is failed, sometimes few pointers may remain
uninitialized ex. priv->wdev, priv->netdev, adapter->sleep_cfm
This will cause NULL pointer dereferance while unloading the
driver.
Signed-off-by: Amitkumar Karwar <akarwar@marvell.com>
Signed-off-by: Kiran Divekar <dkiran@marvell.com>
Signed-off-by: Bing Zhao <bzhao@marvell.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
|
|
Initially diagnosed on Ubuntu 11.04 with kernel 2.6.38.
velocity_close is not called during a suspend / resume cycle in this
driver and it has no business playing directly with power states.
Signed-off-by: David Lv <DavidLv@viatech.com.cn>
Acked-by: Francois Romieu <romieu@fr.zoreil.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Eric Dumazet found that commit 813b3b5db83
(ipv4: Use caller's on-stack flowi as-is in output
route lookups.) that comes in 3.0 added a regression.
The problem appears to be that resulting flowi4_oif is
used incorrectly as input parameter to some routing lookups.
The result is that when connecting to local port without
listener if the IP address that is used is not on a loopback
interface we incorrectly assign RTN_UNICAST to the output
route because no route is matched by oif=lo. The RST packet
can not be sent immediately by tcp_v4_send_reset because
it expects RTN_LOCAL.
So, change ip_route_connect and ip_route_newports to
update the flowi4 fields that are input parameters because
we do not want unnecessary binding to oif.
To make it clear what are the input parameters that
can be modified during lookup and to show which fields of
floiw4 are reused add a new function to update the flowi4
structure: flowi4_update_output.
Thanks to Yurij M. Plotnikov for providing a bug report including a
program to reproduce the problem.
Thanks to Eric Dumazet for tracking the problem down to
tcp_v4_send_reset and providing initial fix.
Reported-by: Yurij M. Plotnikov <Yurij.Plotnikov@oktetlabs.ru>
Signed-off-by: Julian Anastasov <ja@ssi.bg>
Acked-by: Eric Dumazet <eric.dumazet@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Binding RST packet outgoing interface to incoming interface
for tcp v4 when there is no socket associate with it.
when sk is not NULL, using sk->sk_bound_dev_if instead.
(suggested by Eric Dumazet).
This has few benefits:
1. tcp_v6_send_reset already did that.
2. This helps tcp connect with SO_BINDTODEVICE set. When
connection is lost, we still able to sending out RST using
same interface.
3. we are sending reply, it is most likely to be succeed
if iif is used
Signed-off-by: Shawn Lu <shawn.lu@ericsson.com>
Acked-by: Eric Dumazet <eric.dumazet@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
It was recently pointed out to me that the get_prioidx function sets a bit in
the prioidx map prior to checking to see if the index being set is out of
bounds. This patch corrects that, avoiding the possiblity of us writing beyond
the end of the array
Signed-off-by: Neil Horman <nhorman@tuxdriver.com>
Reported-by: Stanislaw Gruszka <sgruszka@redhat.com>
CC: Stanislaw Gruszka <sgruszka@redhat.com>
CC: "David S. Miller" <davem@davemloft.net>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/linville/wireless
|
|
all works need to be initialized before ieee80211_register_hw
to prevent mac80211 call backs such as drv_start, drv_config
getting started. otherwise we would queue/cancel works before
initializing them and it leads to kernel panic.
this issue can be recreated with the following script
in Chrome laptops with AR928X cards, with background scan
running (or) Network manager is running
while true
do
sudo modprobe -v ath9k
sleep 3
sudo modprobe -r ath9k
sleep 3
done
EIP: [<81040a47>] __cancel_work_timer+0xb8/0xe1 SS:ESP 0068:f6be9d70
---[ end trace 4f86d6139a9900ef ]---
Registered led device: ath9k-phy0
ieee80211 phy0: Atheros AR9280 Rev:2 mem=0xf88a0000,
irq=16
Kernel panic - not syncing: Fatal exception
Pid: 456, comm: wpa_supplicant Tainted: G D
3.0.13 #1
Call Trace:
[<81379e21>] panic+0x53/0x14a
[<81004a30>] oops_end+0x73/0x81
[<81004b53>] die+0x4c/0x55
[<81002710>] do_trap+0x7c/0x83
[<81002855>] ? do_bounds+0x58/0x58
[<810028cc>] do_invalid_op+0x77/0x81
[<81040a47>] ? __cancel_work_timer+0xb8/0xe1
[<810489ec>] ? sched_clock_cpu+0x81/0x11f
[<8103f809>] ? wait_on_work+0xe2/0xf7
[<8137f807>] error_code+0x67/0x6c
[<810300d8>] ? wait_consider_task+0x4ba/0x84c
[<81040a47>] ? __cancel_work_timer+0xb8/0xe1
[<810380c9>] ? try_to_del_timer_sync+0x5f/0x67
[<81040a91>] cancel_work_sync+0xf/0x11
[<f88d7b7c>] ath_set_channel+0x62/0x25c [ath9k]
[<f88d67d1>] ? ath9k_tx_last_beacon+0x26a/0x85c [ath9k]
[<f88d8899>] ath_radio_disable+0x3f1/0x68e [ath9k]
[<f90d0edb>] ieee80211_hw_config+0x111/0x116 [mac80211]
[<f90dd95c>] __ieee80211_recalc_idle+0x919/0xa37 [mac80211]
[<f90dda76>] __ieee80211_recalc_idle+0xa33/0xa37 [mac80211]
[<812dbed8>] __dev_open+0x82/0xab
Cc: <stable@vger.kernel.org>
Cc: Gary Morain <gmorain@google.com>
Cc: Paul Stewart <pstew@google.com>
Cc: Vasanthakumar Thiagarajan <vthiagar@qca.qualcomm.com>
Tested-by: Mohammed Shafi Shajakhan <mohammed@qca.qualcomm.com>
Signed-off-by: Rajkumar Manoharan <rmanohar@qca.qualcomm.com>
Signed-off-by: Mohammed Shafi Shajakhan <mohammed@qca.qualcomm.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
|
|
Currently even if association is failed "iw link" shows some
information about connected BSS and "Tx timeout" error is seen in
dmesg log.
This patch fixes below issues in the code to handle assoc failure
case correctly.
1) "status" variable in mwifiex_wait_queue_complete() is not
correctly updated. Hence driver doesn't inform cfg80211 stack
about association failure.
2) During association network queues are stopped but carrier is
not cleared, which gives Tx timeout error in failure case
Signed-off-by: Amitkumar Karwar <akarwar@marvell.com>
Signed-off-by: Bing Zhao <bzhao@marvell.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
|
|
The device seems to survive the issue, so no need to flood the logs
about it...
Signed-off-by: John W. Linville <linville@tuxdriver.com>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/linville/wireless into for-davem
|
|
Correct spelling "packtetbuf_num" to "packetbuf_num" in
drivers/net/ethernet/intel/ixgbe/ixgbe_common.h
Signed-off-by: Masanari Iida <standby24x7@gmail.com>
Tested-by: Phil Schmitt <phillip.j.schmitt@intel.com>
|
|
Change copyright date to 2012 in the source files.
Signed-off-by: Mitch Williams <mitch.a.williams@intel.com>
Tested-by: Robert E Garrett <robertX.e.garrett@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
|
|
Signed-off-by: Greg Rose <gregory.v.rose@intel.com>
Tested-by: Robert E Garrett <robertX.e.garrett@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
|
|
Remove jump to out label that was skipping over code to replace the
ack bit in the mailbox cache variable. This was causing driver mailbox
routines that poll for the PF to ack a message to time out which would
in turn cause all other mailbox messages to fail. Also replace the
mailbox cache variable message indication bit when a message is found
so that other functions that choose to poll for a mailbox message from
the PF won't miss it.
Signed-off-by: Greg Rose <gregory.v.rose@intel.com>
Tested-by: Robert E Garrett <robertX.e.garrett@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
|
|
Signed-off-by: Stephen Hemminger <shemminger@vyatta.com>
Tested-by: Phil Schmitt <phillip.j.schmitt@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
|
