| Age | Commit message (Collapse) | Author |
|---|
|
lockdep warns about following message at boot time on one of my test
machine. Then, schedule_on_each_cpu() sholdn't be called when the task
have mmap_sem.
Actually, lru_add_drain_all() exist to prevent the unevictalble pages
stay on reclaimable lru list. but currenct unevictable code can rescue
unevictable pages although it stay on reclaimable list.
So removing is better.
In addition, this patch add lru_add_drain_all() to sys_mlock() and
sys_mlockall(). it isn't must. but it reduce the failure of moving to
unevictable list. its failure can rescue in vmscan later. but reducing
is better.
Note, if above rescuing happend, the Mlocked and the Unevictable field
mismatching happend in /proc/meminfo. but it doesn't cause any real
trouble.
=======================================================
[ INFO: possible circular locking dependency detected ]
2.6.28-rc2-mm1 #2
-------------------------------------------------------
lvm/1103 is trying to acquire lock:
(&cpu_hotplug.lock){--..}, at: [<c0130789>] get_online_cpus+0x29/0x50
but task is already holding lock:
(&mm->mmap_sem){----}, at: [<c01878ae>] sys_mlockall+0x4e/0xb0
which lock already depends on the new lock.
the existing dependency chain (in reverse order) is:
-> #3 (&mm->mmap_sem){----}:
[<c0153da2>] check_noncircular+0x82/0x110
[<c0185e6a>] might_fault+0x4a/0xa0
[<c0156161>] validate_chain+0xb11/0x1070
[<c0185e6a>] might_fault+0x4a/0xa0
[<c0156923>] __lock_acquire+0x263/0xa10
[<c015714c>] lock_acquire+0x7c/0xb0 (*) grab mmap_sem
[<c0185e6a>] might_fault+0x4a/0xa0
[<c0185e9b>] might_fault+0x7b/0xa0
[<c0185e6a>] might_fault+0x4a/0xa0
[<c0294dd0>] copy_to_user+0x30/0x60
[<c01ae3ec>] filldir+0x7c/0xd0
[<c01e3a6a>] sysfs_readdir+0x11a/0x1f0 (*) grab sysfs_mutex
[<c01ae370>] filldir+0x0/0xd0
[<c01ae370>] filldir+0x0/0xd0
[<c01ae4c6>] vfs_readdir+0x86/0xa0 (*) grab i_mutex
[<c01ae75b>] sys_getdents+0x6b/0xc0
[<c010355a>] syscall_call+0x7/0xb
[<ffffffff>] 0xffffffff
-> #2 (sysfs_mutex){--..}:
[<c0153da2>] check_noncircular+0x82/0x110
[<c01e3d2c>] sysfs_addrm_start+0x2c/0xc0
[<c0156161>] validate_chain+0xb11/0x1070
[<c01e3d2c>] sysfs_addrm_start+0x2c/0xc0
[<c0156923>] __lock_acquire+0x263/0xa10
[<c015714c>] lock_acquire+0x7c/0xb0 (*) grab sysfs_mutex
[<c01e3d2c>] sysfs_addrm_start+0x2c/0xc0
[<c04f8b55>] mutex_lock_nested+0xa5/0x2f0
[<c01e3d2c>] sysfs_addrm_start+0x2c/0xc0
[<c01e3d2c>] sysfs_addrm_start+0x2c/0xc0
[<c01e3d2c>] sysfs_addrm_start+0x2c/0xc0
[<c01e422f>] create_dir+0x3f/0x90
[<c01e42a9>] sysfs_create_dir+0x29/0x50
[<c04faaf5>] _spin_unlock+0x25/0x40
[<c028f21d>] kobject_add_internal+0xcd/0x1a0
[<c028f37a>] kobject_set_name_vargs+0x3a/0x50
[<c028f41d>] kobject_init_and_add+0x2d/0x40
[<c019d4d2>] sysfs_slab_add+0xd2/0x180
[<c019d580>] sysfs_add_func+0x0/0x70
[<c019d5dc>] sysfs_add_func+0x5c/0x70 (*) grab slub_lock
[<c01400f2>] run_workqueue+0x172/0x200
[<c014008f>] run_workqueue+0x10f/0x200
[<c0140bd0>] worker_thread+0x0/0xf0
[<c0140c6c>] worker_thread+0x9c/0xf0
[<c0143c80>] autoremove_wake_function+0x0/0x50
[<c0140bd0>] worker_thread+0x0/0xf0
[<c0143972>] kthread+0x42/0x70
[<c0143930>] kthread+0x0/0x70
[<c01042db>] kernel_thread_helper+0x7/0x1c
[<ffffffff>] 0xffffffff
-> #1 (slub_lock){----}:
[<c0153d2d>] check_noncircular+0xd/0x110
[<c04f650f>] slab_cpuup_callback+0x11f/0x1d0
[<c0156161>] validate_chain+0xb11/0x1070
[<c04f650f>] slab_cpuup_callback+0x11f/0x1d0
[<c015433d>] mark_lock+0x35d/0xd00
[<c0156923>] __lock_acquire+0x263/0xa10
[<c015714c>] lock_acquire+0x7c/0xb0
[<c04f650f>] slab_cpuup_callback+0x11f/0x1d0
[<c04f93a3>] down_read+0x43/0x80
[<c04f650f>] slab_cpuup_callback+0x11f/0x1d0 (*) grab slub_lock
[<c04f650f>] slab_cpuup_callback+0x11f/0x1d0
[<c04fd9ac>] notifier_call_chain+0x3c/0x70
[<c04f5454>] _cpu_up+0x84/0x110
[<c04f552b>] cpu_up+0x4b/0x70 (*) grab cpu_hotplug.lock
[<c06d1530>] kernel_init+0x0/0x170
[<c06d15e5>] kernel_init+0xb5/0x170
[<c06d1530>] kernel_init+0x0/0x170
[<c01042db>] kernel_thread_helper+0x7/0x1c
[<ffffffff>] 0xffffffff
-> #0 (&cpu_hotplug.lock){--..}:
[<c0155bff>] validate_chain+0x5af/0x1070
[<c040f7e0>] dev_status+0x0/0x50
[<c0156923>] __lock_acquire+0x263/0xa10
[<c015714c>] lock_acquire+0x7c/0xb0
[<c0130789>] get_online_cpus+0x29/0x50
[<c04f8b55>] mutex_lock_nested+0xa5/0x2f0
[<c0130789>] get_online_cpus+0x29/0x50
[<c0130789>] get_online_cpus+0x29/0x50
[<c017bc30>] lru_add_drain_per_cpu+0x0/0x10
[<c0130789>] get_online_cpus+0x29/0x50 (*) grab cpu_hotplug.lock
[<c0140cf2>] schedule_on_each_cpu+0x32/0xe0
[<c0187095>] __mlock_vma_pages_range+0x85/0x2c0
[<c0156945>] __lock_acquire+0x285/0xa10
[<c0188f09>] vma_merge+0xa9/0x1d0
[<c0187450>] mlock_fixup+0x180/0x200
[<c0187548>] do_mlockall+0x78/0x90 (*) grab mmap_sem
[<c01878e1>] sys_mlockall+0x81/0xb0
[<c010355a>] syscall_call+0x7/0xb
[<ffffffff>] 0xffffffff
other info that might help us debug this:
1 lock held by lvm/1103:
#0: (&mm->mmap_sem){----}, at: [<c01878ae>] sys_mlockall+0x4e/0xb0
stack backtrace:
Pid: 1103, comm: lvm Not tainted 2.6.28-rc2-mm1 #2
Call Trace:
[<c01555fc>] print_circular_bug_tail+0x7c/0xd0
[<c0155bff>] validate_chain+0x5af/0x1070
[<c040f7e0>] dev_status+0x0/0x50
[<c0156923>] __lock_acquire+0x263/0xa10
[<c015714c>] lock_acquire+0x7c/0xb0
[<c0130789>] get_online_cpus+0x29/0x50
[<c04f8b55>] mutex_lock_nested+0xa5/0x2f0
[<c0130789>] get_online_cpus+0x29/0x50
[<c0130789>] get_online_cpus+0x29/0x50
[<c017bc30>] lru_add_drain_per_cpu+0x0/0x10
[<c0130789>] get_online_cpus+0x29/0x50
[<c0140cf2>] schedule_on_each_cpu+0x32/0xe0
[<c0187095>] __mlock_vma_pages_range+0x85/0x2c0
[<c0156945>] __lock_acquire+0x285/0xa10
[<c0188f09>] vma_merge+0xa9/0x1d0
[<c0187450>] mlock_fixup+0x180/0x200
[<c0187548>] do_mlockall+0x78/0x90
[<c01878e1>] sys_mlockall+0x81/0xb0
[<c010355a>] syscall_call+0x7/0xb
Signed-off-by: KOSAKI Motohiro <kosaki.motohiro@jp.fujitsu.com>
Tested-by: Kamalesh Babulal <kamalesh@linux.vnet.ibm.com>
Cc: Lee Schermerhorn <Lee.Schermerhorn@hp.com>
Cc: Christoph Lameter <cl@linux-foundation.org>
Cc: Heiko Carstens <heiko.carstens@de.ibm.com>
Cc: Nick Piggin <nickpiggin@yahoo.com.au>
Cc: Hugh Dickins <hugh@veritas.com>
Cc: Rik van Riel <riel@redhat.com>
Cc: Peter Zijlstra <peterz@infradead.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
|
|
__register_kprobe() can be preempted after checking probing address but
before module_text_address() or try_module_get(), and in this interval
the module can be unloaded. In that case, try_module_get(probed_mod)
will access to invalid address, or kprobe will probe invalid address.
This patch uses preempt_disable() to protect it and uses
__module_text_address() and __kernel_text_address().
Signed-off-by: Lai Jiangshan <laijs@cn.fujitsu.com>
Signed-off-by: Masami Hiramatsu <mhiramat@redhat.com>
Cc: Ananth N Mavinakayanahalli <ananth@in.ibm.com>
Cc: Hiroshi Shimamoto <h-shimamoto@ct.jp.nec.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
|
|
With this change, control file 'freezer.state' doesn't exist in root
cgroup, making root cgroup unfreezable.
I think it's reasonable to disallow freeze tasks in the root cgroup. And
then we can avoid fork overhead when freezer subsystem is compiled but not
used.
Also make writing invalid value to freezer.state returns EINVAL rather
than EIO. This is more consistent with other cgroup subsystem.
Signed-off-by: Li Zefan <lizf@cn.fujitsu.com>
Acked-by: Paul Menage <menage@google.com>
Cc: Cedric Le Goater <clg@fr.ibm.com>
Cc: Paul Menage <menage@google.com>
Cc: Matt Helsley <matthltc@us.ibm.com>
Cc: "Serge E. Hallyn" <serue@us.ibm.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
|
|
In theory the task can be moved to another cgroup and the freezer will be
freed right after task_lock is dropped, so the lock results in zero
protection.
But in the case of freezer_fork() no lock is needed, since the task is not
in tasklist yet so it won't be moved to another cgroup, so task->cgroups
won't be changed or invalidated.
Signed-off-by: Li Zefan <lizf@cn.fujitsu.com>
Cc: Matt Helsley <matthltc@us.ibm.com>
Cc: Cedric Le Goater <clg@fr.ibm.com>
Cc: "Serge E. Hallyn" <serue@us.ibm.com>
Cc: Paul Menage <menage@google.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
|
|
This driver supports the Xilinx XPS GPIO IP core which has the typical
GPIO features.
Signed-off-by: Kiran Sutariya <kirans@xilinx.com>
Signed-off-by: John Linn <john.linn@xilinx.com>
Cc: David Brownell <david-b@pacbell.net>
Cc: Paul Mackerras <paulus@samba.org>
Cc: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Cc: Kumar Gala <galak@gate.crashing.org>
Cc: "Grant Likely" <grant.likely@secretlab.ca>
Cc: <avorontsov@ru.mvista.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
|
|
If all allowable memory is unreclaimable, it is possible to loop forever
in the page allocator for ~__GFP_NORETRY allocations.
During this time, it is also possible for a task's cpuset to expand its
set of allowable nodes so that it now includes free memory. The cached
copy of this set, current->mems_allowed, is stale, however, since there
has not been a subsequent call to cpuset_update_task_memory_state().
The cached copy of the set of allowable nodes is now updated in the page
allocator's slow path so the additional memory is available to
get_page_from_freelist().
[akpm@linux-foundation.org: add comment]
Signed-off-by: David Rientjes <rientjes@google.com>
Cc: Paul Menage <menage@google.com>
Cc: Christoph Lameter <cl@linux-foundation.org>
Cc: Mel Gorman <mel@csn.ul.ie>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
|
|
It turns out that edac_mc_del_mc will kobject_put the last kref on the
mci object.
If the timing is just right, that means that the mci object is freed
before before i5000_remove_one has a chance to free the resources
associated with it, causing a null pointer exceptions when unloading the
driver. Insert a kobject_{get,put} pair so that this doesn't happen.
Signed-off-by: Darrick J. Wong <djwong@us.ibm.com>
Cc: Doug Thompson <norsk5@yahoo.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
|
|
It turns out that if one registers a struct platform_device, the
platform device code expects that platform_device.device->driver points
to a struct driver inside a struct platform_driver.
This is not the case with the ipmi-si, ipmi-msghandler and ibmaem
drivers, which causes the suspend/resume hook functions to jump off into
nowhere, causing a crash. Make this assumption hold true for these
three drivers.
Signed-off-by: Darrick J. Wong <djwong@us.ibm.com>
Acked-by: Corey Minyard <cminyard@mvista.com>
Cc: Jean Delvare <khali@linux-fr.org>
Cc: Kay Sievers <kay.sievers@vrfy.org>
Cc: Greg KH <greg@kroah.com>
Cc: <stable@kernel.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
|
|
Changed because old the definition of unsigned long cannot be negative.
Signed-off-by: Nicolas Ferre <nicolas.ferre@atmel.com>
Reported-by: Roel Kluin <roel.kluin@gmail.com>
Cc: Haavard Skinnemoen <hskinnemoen@atmel.com>
Cc: Andrew Victor <linux@maxim.org.za>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
|
|
This patch adds accelerometer and temperature sensor support for Macbook 4.
Signed-off-by: Henrik Rydberg <rydberg@euromail.se>
Cc: Nicolas Boichat <nicolas@boichat.ch
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
|
|
Oops. Part of the hugetlb private reservation code was not fully
converted to use hstates.
When a huge page must be unmapped from VMAs due to a failed COW,
HPAGE_SIZE is used in the call to unmap_hugepage_range() regardless of
the page size being used. This works if the VMA is using the default
huge page size. Otherwise we might unmap too much, too little, or
trigger a BUG_ON. Rare but serious -- fix it.
Signed-off-by: Adam Litke <agl@us.ibm.com>
Cc: Jon Tollefson <kniht@linux.vnet.ibm.com>
Cc: Mel Gorman <mel@csn.ul.ie>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
|
|
* git://git.kernel.org/pub/scm/linux/kernel/git/davem/net-2.6:
bnx2: fix poll_controller to pass proper structures and check all rx queues
niu: Fix readq implementation when architecture does not provide one.
hostap: pad the skb->cb usage in lieu of a proper fix
rtl8187 : support for Sitecom WL-168 0001 v4
mac80211: fix notify_mac function
rtl8187: Add Abocom USB ID
net: put_cmsg_compat + SO_TIMESTAMP[NS]: use same name for value as caller
tcp_htcp: last_cong bug fix
[netdrvr] smc911x: fix for driver resume (and compilation warning)
RDMA/cxgb3: deadlock in iw_cxgb3 can cause hang when configuring interface.
cxgb3 - Limit multiqueue setting to msi-x
cxgb3 - eeprom read fixes
myri10ge: fix stop/go ordering even more
|
|
Fix bnx2 so that netpoll works properly. Specifically:
1) Fix parameters to bnx2_interrupt to be a struct bnx2_napi rather than a
struct net_device
2) Fix poll_controller method to check every queue in the rx case so frames
aren't missed
Signed-off-by: Neil Horman <nhorman@tuxdriver.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/linville/wireless-2.6
|
|
This fixes a TX hang reported by Jesper Dangaard Brouer.
When an architecutre cannot provide a fully functional
64-bit atomic readq/writeq, the driver must implement
it's own. This is because only the driver can say whether
doing something like using two 32-bit reads to implement
the full 64-bit read will actually work properly.
In particular one of the issues is whether the top 32-bits
or the bottom 32-bits of the 64-bit register should be read
first. There could be side effects, and in fact that is
exactly the problem here.
The TX_CS register has counters in the upper 32-bits and
state bits in the lower 32-bits. A read clears the state
bits.
We would read the counter half before the state bit half.
That first read would clear the state bits, and then the
driver thinks that no interrupts are pending because the
interrupt indication state bits are seen clear every time.
Fix this by reading the bottom half before the upper half.
Tested-by: Jesper Dangaard Brouer <jdb@comx.dk>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Like mac80211 did, this driver makes 'clever' use of skb->cb to pass
information along with an skb as it is requeued from the virtual device
to the physical wireless device. Unfortunately, that trick no longer
works...
Unlike mac80211, code complexity and driver apathy makes this hack
the best option we have in the short run. Hopefully someone will
eventually be motivated to code a proper fix before all the effected
hardware dies.
(Above text by me. Johannes officially disavows all knowledge of this
hack. -- JWL)
Signed-off-by: Johannes Berg <johannes@sipsolutions.net>
Cc: stable@kernel.org
Signed-off-by: John W. Linville <linville@tuxdriver.com>
|
|
the Sitecom 0001 v4 with product id 0x0df6:0028, uses Realtek's
RTL8187B and work fine with new 2.6.27 driver.
Signed-off-by: John W. Linville <linville@tuxdriver.com>
|
|
The ieee80211_notify_mac() function uses ieee80211_sta_req_auth() which
in turn calls ieee80211_set_disassoc() which calls a few functions that
need to be able to sleep, so ieee80211_notify_mac() cannot use RCU
locking for the interface list and must use rtnl locking instead.
Signed-off-by: Johannes Berg <johannes@sipsolutions.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
|
|
Signed-off-by: Ivan Kuten <ivan.kuten@promwad.com>
Signed-off-by: Larry Finger <Larry.Finger@lwfinger.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/tip/linux-2.6-tip
* 'timers-fixes-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/linux-2.6-tip:
hrtimer: clean up unused callback modes
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/djbw/async_tx
* 'fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/djbw/async_tx:
dmaengine: struct device - replace bus_id with dev_name(), dev_set_name()
iop-adma: use iop_paranoia() for debug BUG_ONs
iop-adma: add a dummy read to flush next descriptor update
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/roland/infiniband
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/roland/infiniband:
IPoIB: Fix crash in path_rec_completion()
IPoIB: Fix hang in ipoib_flush_paths()
IPoIB: Don't enable NAPI when it's already enabled
RDMA/cxgb3: Fix deadlock in iw_cxgb3 (hang when configuring interface)
IB/ehca: Remove reference to special QP in case of port activation failure
IB/mlx4: Set umem field to NULL in mlx4_ib_alloc_fast_reg_mr()
mlx4_core: Fix unused variable warning
RDMA/nes: Mitigate compatibility issue regarding PCIe write credits
RDMA/nes: Fix CQ allocation scheme for multicast receive queue apps
RDMA/nes: Correct handling of PBL resources
RDMA/nes: Reindent mis-indented spinlocks
RDMA/cxgb3: Fix too-big reserved field zeroing in iwch_post_zb_read()
IB/ipath: Fix RDMA write with immediate copy of last packet
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/tiwai/sound-2.6
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tiwai/sound-2.6:
ALSA: hda - Fix IDT/STAC multiple HP detection
ALSA: hda - Fix input pin initialization for STAC/IDT codecs
ALSA: hda - Add missing analog-mux mixer creation for STAC9200
|
|
Don't do misalignment handling for userspace misalignment faults: just
generate an appropriate SIGBUS instead.
Signed-off-by: David Howells <dhowells@redhat.com>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
|
|
Don't handle the misaligned loading and storing of the SP register as in C code
that's most certainly a compiler bug.
Signed-off-by: David Howells <dhowells@redhat.com>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
|
|
Support misalignment handling for instructions that have kernel SP-based
address operands, including fixing those that include IMM8 or IMM16
displacements.
Signed-off-by: David Howells <dhowells@redhat.com>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
|
|
Fix misalignment handling for an address calculated from the sum of two
registers.
Signed-off-by: David Howells <dhowells@redhat.com>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
|
|
Correctly handle misalignment in MOV instructions with postinc-with-immediate
addressing mode operands. In these, the immediate value is the increment to
be applied the address register, not the displacement to the address.
Signed-off-by: David Howells <dhowells@redhat.com>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
|
|
Perform misalignment fixups of the MOV_Lcc instructions (move postinc memory
to register and conditionally loop).
Signed-off-by: David Howells <dhowells@redhat.com>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
|
|
Allow misalignment fixup in interrupt handling in the MN10300 arch.
Signed-off-by: David Howells <dhowells@redhat.com>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
|
|
Fix misalignment handling of operands with register postincrement addressing.
The flag to indicate that postincrement is required should not be interpreted
as an specification of a value to be added to the address.
Also add BUGs to catch unimplemented parameter markings in the opcodes table.
Signed-off-by: David Howells <dhowells@redhat.com>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
|
|
Extract the displacement from an MN10300 instruction correctly in the
misalignment fixup handler.
The code should extract the displacement in LSB order, not MSB order.
Signed-off-by: David Howells <dhowells@redhat.com>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
|
|
Add further misalignment fixup support to the MN10300 arch, notably for ABS32
and SP+disp addressing.
Signed-off-by: David Howells <dhowells@redhat.com>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
|
|
Add configurable built-in testing for the MN10300 misalignment handler.
Signed-off-by: David Howells <dhowells@redhat.com>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
|
|
Clean up the MN10300 misalignment handler a little by:
(1) Use ilog2() rather than doing implementing log2() locally.
(2) Make format_tbl[] const and static.
(3) Making the debugging prints more consistent.
Signed-off-by: David Howells <dhowells@redhat.com>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/avi/kvm
* 'kvm-updates/2.6.28' of git://git.kernel.org/pub/scm/linux/kernel/git/avi/kvm:
KVM: Fix pit memory leak if unable to allocate irq source id
KVM: ia64: fix vmm_spin_{un}lock for !CONFIG_SMP
KVM: VMX: Set IGMT bit in EPT entry
KVM: Require the PCI subsystem
x86: KVM guest: fix section mismatch warning in kvmclock.c
KVM: ia64: Use guest signal mask when blocking
KVM: MMU: increase per-vcpu rmap cache alloc size
|
|
The STACK_GROWSUP case of stack expansion was missing a test for 'prev',
which got removed by commit cb8f488c33539f096580e202f5438a809195008f
("mmap.c: deinline a few functions") by mistake.
I found my original email in "sent" folder. The patch in that mail
does NOT remove !prev. That change had beed added by someone else.
Ok, I think we are not much interested in who did it, let's
fix it for good.
[ "It looks like this was caused by me fixing rejects. That was the
fancy include-lots-of-context-so-it-wont-apply patch." - akpm ]
Reported-and-bisected-by: Helge Deller <deller@gmx.de>
Signed-off-by: Denys Vlasenko <vda.linux@googlemail.com>
Cc: Andrew Morton <akpm@linux-foundation.org>
Cc: Jiri Kosina <jkosina@suse.cz>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/lenb/linux-acpi-2.6
* 'release' of git://git.kernel.org/pub/scm/linux/kernel/git/lenb/linux-acpi-2.6: (47 commits)
ACPI: pci_link: remove acpi_irq_balance_set() interface
fujitsu-laptop: Add DMI callback for Lifebook S6420
ACPI: EC: Don't do transaction from GPE handler in poll mode.
ACPI: EC: lower interrupt storm treshold
ACPICA: Use spinlock for acpi_{en|dis}able_gpe
ACPI: EC: restart failed command
ACPI: EC: wait for last write gpe
ACPI: EC: make kernel messages more useful when GPE storm is detected
ACPI: EC: revert msleep patch
thinkpad_acpi: fingers off backlight if video.ko is serving this functionality
sony-laptop: fingers off backlight if video.ko is serving this functionality
msi-laptop: fingers off backlight if video.ko is serving this functionality
fujitsu-laptop: fingers off backlight if video.ko is serving this functionality
eeepc-laptop: fingers off backlight if video.ko is serving this functionality
compal: fingers off backlight if video.ko is serving this functionality
asus-acpi: fingers off backlight if video.ko is serving this functionality
Acer-WMI: fingers off backlight if video.ko is serving this functionality
ACPI video: if no ACPI backlight support, use vendor drivers
ACPI: video: Ignore devices that aren't present in hardware
Delete an unwanted return statement at evgpe.c
...
|
|
|
|
Fix a crash in path_rec_completion() during an SM up/down loop. If
more than one path record request is issued, the first completion
releases path->done, allowing ipoib_flush_paths() to free the path,
and thus corrupting it for the second completion.
Commit ee1e2c82 ("IPoIB: Refresh paths instead of flushing them on SM
change events") added the field path->valid and changed the test "if
(!path)" to "if (!path || !path->valid)". This change made it
possible for a path with an outstanding query to pass the test and
issue another query on the same path. Having two queries on the same
path leads to a crash.
This fixes <https://bugs.openfabrics.org/show_bug.cgi?id=1325>.
Signed-off-by: Yossi Etigin <yosefe@voltaire.com>
Signed-off-by: Roland Dreier <rolandd@cisco.com>
|
|
ipoib_flush_paths() can hang during an SM up/down loop: if
path_rec_start() fails (for instance, because there is no sm_ah), the
path is still added to the path list by neigh_add_path(). Then,
ipoib_flush_paths() will wait for path->done, but it will never
complete because the request was not issued at all. Fix this by
completing path->done if issuing the query fails.
This fixes <https://bugs.openfabrics.org/show_bug.cgi?id=1329>.
Signed-off-by: Yossi Etigin <yosefe@voltaire.com>
Signed-off-by: Roland Dreier <rolandd@cisco.com>
|
|
If a P_Key is not present when an interface is created, ipoib_open()
will return after doing napi_enable(). ipoib_open() will be called
again from ipoib_pkey_poll() when the P_Key appears, after NAPI has
already been enabled, and try to enable it again. This triggers a
BUG_ON() in napi_enable().
Fix this by moving the call to napi_enable() to after the test for
P_Key presence.
Signed-off-by: Yossi Etigin <yosefe@voltaire.com>
Signed-off-by: Roland Dreier <rolandd@cisco.com>
|
|
When the iw_cxgb3 module's cxgb3_client "add" func gets called by the
cxgb3 module, the iwarp driver ends up calling the ethtool ops
get_drvinfo function in cxgb3 to get the fw version and other info.
Currently the iwarp driver grabs the rtnl lock around this down call
to serialize. As of 2.6.27 or so, things changed such that the rtnl
lock is held around the call to the netdev driver open function. Also
the cxgb3_client "add" function doesn't get called if the device is
down.
So, if you load cxgb3, then load iw_cxgb3, then ifconfig up the
device, the iw_cxgb3 add func gets called with the rtnl_lock held. If
you load cxgb3, ifconfig up the device, then load iw_cxgb3, the add
func gets called without the rtnl_lock held. The former causes the
deadlock, the latter does not.
In addition, there are iw_cxgb3 sysfs handlers that also can call down
into cxgb3 to gather the fw and hw versions. These can be called
concurrently on different processors and at any time. Thus we need to
push this serialization down in the cxgb3 driver get_drvinfo func.
The fix is to remove rtnl lock usage, and use a per-device lock in cxgb3.
Signed-off-by: Steve Wise <swise@opengridcomputing.com>
Acked-by: Divy Le Ray <divy@chelsio.com>
Signed-off-by: Roland Dreier <rolandd@cisco.com>
|
|
In __sock_recv_timestamp() the additional SCM_TIMESTAMP[NS] is used. This
has the same value as SO_TIMESTAMP[NS], so this is a purely cosmetic change.
Signed-off-by: Patrick Ohly <patrick.ohly@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
This patch fixes a minor bug in tcp_htcp.c which has been
highlighted by Lachlan Andrew and Lawrence Stewart. Currently, the
time since the last congestion event, which is stored in variable
last_cong, is reset whenever there is a state change into
TCP_CA_Open. This includes transitions of the type
TCP_CA_Open->TCP_CA_Disorder->TCP_CA_Open which are not associated
with backoff of cwnd. The patch changes last_cong to be updated
only on transitions into TCP_CA_Open that occur after experiencing
the congestion-related states TCP_CA_Loss, TCP_CA_Recovery,
TCP_CA_CWR.
Signed-off-by: Doug Leith <doug.leith@nuim.ie>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
|
|
Due to the recent change for multiple HP as line-out switch, only
one of the multiple headphons (usually a wrong one) is toggled
and the other pins are still disabled. This causes the silent output
problem on some Dell laptops.
Also, the hp_switch check is screwed up when a line-in or a mic-in
jack exists. This is added as an additional output, but hp_switch
check doesn't take it into account.
This patch fixes these issues: simplify hp_switch check by using
the NID instead of bool, and clean up / fix the toggle of HP pins
in unsol event handler code.
Reference: Novell bnc#443267
https://bugzilla.novell.com/show_bug.cgi?id=443267
Signed-off-by: Takashi Iwai <tiwai@suse.de>
|
|
Impact: cleanup
git grep HRTIMER_CB_IRQSAFE revealed half the callback modes are actually
unused.
Signed-off-by: Peter Zijlstra <a.p.zijlstra@chello.nl>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
|
|
|
|
|
