summaryrefslogtreecommitdiffstats
AgeCommit message (Collapse)Author
2005-11-07[MTD] core: Clean up trailing white spacesThomas Gleixner
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
2005-11-07[MTD] chips cfi_cmdset_0002: Prevent timeout raceKonstantin Baidarov
We've noticed that sometimes "MTD do_write_buffer(): software timeout" message was printed out when writing to a Fujitsu NOR flash. It turned out that this was because of a race in the timeout handling do_write_buffer(). A small timeout of (HZ / 1000) + 1 is used there, and sometimes if the timer interrupt handling takes more than one or even two jiffies (which is 1-2 ms with HZ == 1000) and that interrupt happens just after chip_ready() call, the driver bails out from a ready polling loop despite the chip has actually become ready while all those interrupts were handled. To deal with this issue, extra check for chip ready is neccessary on timeout expiration (and the checks should better be reordered). As do_write_oneword() uses the same approach, it needs to also be changed. Signed-off-by: Konstantin Baidarov <kbaidarov@ru.mvista.com> Signed-off-by: Sergei Shtylyov <sshtylyov@ru.mvista.com> Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
2005-11-07[MTD] maps: Add support for the "TQM834x" BoardsMarian Balakowicz
The following patch adds support for the TQ Systems TQM834x Boards. Verified on TQM8349L. This is a resubmit after integrating the suggested changes. Signed-off-by: Marian Balakowicz <m8@semihalf.com> Signed-off-by: Wolfgang Denk <wd@denx.de> Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
2005-11-07[MTD] maps ixp2000: fix compile warnings in ixp2000 map driverLennert Buytenhek
Fix two compile warnings that occur because of treating two 'unsigned long's as 'void *'s. Signed-off-by: Lennert Buytenhek <buytenh@wantstofly.org> Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
2005-11-07[MTD] NAND Kconfig: Simplify dependenciesThomas Gleixner
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
2005-11-07[MTD] maps/plat-ram: Avoid gcc 4.0 warningThomas Gleixner
The assignement of a "const char *" to a "char *" variable is emitting a warning with gcc 4.0. We cannot change mtd->name to "const char *" as we have dynamic assignements of the name. So casting is the correct solution here Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
2005-11-07[MTD] NAND: nand_write_ecc memory and OOB corruptionTodd Poynor
Nathan Roberts noticed the nand_write_ecc index into oobbuf goes out of bounds when crossing an erase block boundary, causing incorrect OOB data to be written and corrupting memory. Reset the index to zero after re-preparing oobbuf for a new erase block. Signed-off-by: Todd Poynor <tpoynor@mvista.com> Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
2005-11-07[MTD] NAND nand_base: Fix shift for bad block check (16bit devices only)Vitaly Wool
In case of an odd offset, the result was shifted by 1 instead of 8 Signed-off-by: Vitaly Wool <vwool@ru.mvista.com> Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
2005-11-07[MTD] OneNAND/Kconfig: Fix dependenciesThomas Gleixner
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
2005-11-07Revert "[PATCH] OneNAND: Add simulator"Thomas Gleixner
This reverts 405c829f98d216925de00af2ee52f969f2c2891c commit.
2005-11-07[MTD] maps/Kconfig: Simplify and update dependenciesSean Young
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
2005-11-07[MTD] maps/ts5500: Fix partition support. Code cleanupSean Young
Signed-off-by: Sean Young <sean@mess.org> Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
2005-11-07[MTD] Tidy up Tims include cleanupThomas Gleixner
While we are at it, reorder the includes and remove the silly /* TASK */ comment Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
2005-11-07[MTD] maps/ixp4xx: kill some warningsDavid Vrabel
- Use map.virt instead of map.map_priv_1 since it has the correct type. - Use readw/writew instead of dereferencing an ioremap'd cookie. - Remove an unused variable. Signed-off-by: David Vrabel <dvrabel@arcom.com> Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
2005-11-06[MTD] NAND sharpsl.c: Add support for akita and borzoi modelsRichard Purdie
The Sharp Zaurus akita and borzoi models are large page flash devices. This patch adds support for them to the sharpsl MTD NAND driver but keeps the oob layout and bad block positions compatible with the Sharp Zaurus 2.4 kernel and ROM bootloader. Signed-off-by: Richard Purdie <rpurdie@rpsys.net> Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
2005-11-06[MTD] chips/cfi_cmdset_0001: fix for P30 cfi parsingNicolas Pitre
Change to the extended cfi table parsing for Intel NOR flash that uses the info in the extended table to 'walk' the table rather than using hard coding for various primary extended query table version numbers. From: Jared Hulbert <jaredeh@gmail.com> Signed-off-by: Nicolas Pitre <nico@cam.org> Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
2005-11-06[JFFS2] Fix broken compile when debug level = 2Artem B. Bityutskiy
Signed-off-by: Artem B. Bityutskiy <dedekind@infradead.org> Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
2005-11-06[MTD] NAND s3c2410.c: Fix timing calculation bugsBen Dooks
Spotted by basprog@mail.ru Signed-off-by: Ben Dooks <ben-linux@fluff.org> Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
2005-11-06[JFFS2] Return 0, not number of bytes written, for success at commit_writeTodd Poynor
Some callers to block-layer commit_write function treat non-zero return as error, notably the loopback mount driver sometimes used in conjunction with JFFS2 on NAND flash for bad block avoidance, etc. Return zero for success as do various other commit_write functions. Signed-off-by: Todd Poynor <tpoynor@mvista.com> Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
2005-11-06[MTD] Don't let gcc inline functions marked __xipramNicolas Pitre
If they get inlined into non __xipram functions we're screwed. Signed-off-by: Nicolas Pitre <nico@cam.org> Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
2005-11-06[MTD] NAND s3c2410.c: Fix missing dev parameter to dev_errBen Dooks
Signed-off-by: Ben Dooks <ben@simtec.co.uk> Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
2005-11-06[MTD] maps/plat-ram.c: Initialize owner in device_driver structBen Dooks
Added .owner initialisation to allow the tracking of the device_driver owners when built as a module Signed-off-by: Ben Dooks <ben-linux@fluff.org> Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
2005-11-06[MTD] maps/bast-flash.c: Initialize owner in device_driver structBen Dooks
Added owner to device driver field for tracking when loaded as a module. Signed-off-by: Ben Dooks <ben@simtec.co.uk> Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
2005-11-06[MTD] NAND: s3c2410.c Initialize owner in device_driver structBen Dooks
Added owner fields to the device_driver for tracking ownership when built as a module Signed-off-by: Ben Dooks <ben@simtec.co.uk> Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
2005-11-06[MTD] mtdpart.c: Allow eraseblock size != power of 2Artem B. Bityutskiy
Don't assume eraseblock size is power of 2. Dataflash can have aligned eraseblock size. From: Peter Menzebach <pm-mtd@mw-itcon.de> Acked-by: Artem B. Bityutskiy <dedekind@infradead.org> Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
2005-11-06[JFFS2] Fix dataflash supportArtem B. Bityutskiy
- assume wbuf may be of size which is not power of 2 - don't make strange assumption about not padding wbuf for DataFlash - use wbuf = DataFlash page and eraseblock >= 8 Dataflash pages From: Peter Menzebach <pm-mtd@mw-itcon.de> Acked-by: Artem B. Bityutskiy <dedekind@infradead.org> Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
2005-11-06[MTD] OneNAND: Enhanced support for DDP (Dual Densitiy Packages)Kyungmin Park
Add density mask for better support of DDP chips. Signed-off-by: Kyungmin Park <kyungmin.park@samsung.com> Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
2005-11-06[MTD] OneNAND: Power Management (PM) supportKyungmin Park
Add suspend/resume Signed-off-by: Kyungmin Park <kyungmin.park@samsung.com> Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
2005-11-06[JFFS2] Use memset(struct) instead of nulling struct members one by oneArtem B. Bityutskiy
Signed-off-by: Artem B. Bityutskiy <dedekind@infradead.org> Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
2005-11-06[JFFS2] Remove stale commentArtem B. Bityutskiy
Signed-off-by: Artem B. Bityutskiy <dedekind@infradead.org> Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
2005-11-06[MTD] OneNAND: Add missing filesKyungmin Park
Simple bad block table source and header files Signed-off-by: Kyungmin Park <kyungmin.park@samsung.com> Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
2005-11-06[MTD] NAND: s3c2410 use dev_err() to report errors instead of printk()Ben Dooks
Signed-off-by: Ben Dooks <ben@simtec.co.uk> Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
2005-11-06[JFFS2] Rename jffs2_summary_node to jffs2_raw_summaryFerenc Havasi
Signed-off-by: Ferenc Havasi <havasi@inf.u-szeged.hu> Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
2005-11-06[MTD] NAND: Alchemy board driver cleanupPete Popov
- cleaned up the partitions and include files - added more flexible CS and address detection and setup Regression tested on db1200 and db1550. Signed-off-by: Pete Popov <ppopov@pacbell.net> Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
2005-11-06[JFFS2] Debug code simplification, update TODOArtem B. Bityutskiy
Simplify the debugging code further. Update the TODO list Signed-off-by: Artem B. Bityutskiy <dedekind@infradead.org> Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
2005-11-06[MTD] maps: Add support for MTX-1 Flash deviceJoern Engel
Add support for "4G Systems MTX-1 Flash device", better known as meshcube. From: Bruno Randolf <bruno.randolf@4g-systems.biz> Signed-off-by: Joern Engel <joern@wohnheim.fh-wedel.de> Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
2005-11-06[JFFS2] Account summary space in reserved_size.Ferenc Havasi
Always keep valid data in reserved_size. It did not cause problems, but the reservation code was unoptimal when centralized summary was active or the size of the erase block was very small. Signed-off-by: Ferenc Havasi <havasi@inf.u-szeged.hu> Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
2005-11-06[MTD] NAND: Add suspend/resume functionalityVitaly Wool
The changes introduced allow to suspend/resume NAND flash. A new state (FL_PM_SUSPENDED) is introduced, as well as routines for mtd->suspend and mtd->resume to put the flash in suspended state from software pov. Signed-off-by: Vitaly Wool <vwool@ru.mvista.com> Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
2005-11-06[MTD] maps: Add mapping driver for PQ2FADS boards.Todd Poynor
From: Vitaly Bordug <vbordug@ru.mvista.com> Signed-off-by: Todd Poynor <tpoynor@mvista.com> Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
2005-11-06[JFFS2] Debug message format clean upArtem B. Bityutskiy
Signed-off-by: Artem B. Bityutskiy <dedekind@infradead.org> Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
2005-11-06[JFFS2] Call summary collector for all mtd devices with writev supportFerenc Havasi
Do the summary collection in the right place. If the device was not writebuffered but had c->mtd->writev function (e.g. blkmtd) the summary collector function was not called. Signed-off-by: Ferenc Havasi <havasi@inf.u-szeged.hu> Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
2005-11-06OneNAND: Remove OMAP platform driverKyungmin Park
Now we can use the generic platform driver Signed-off-by: Kyungmin Park <kyungmin.park@samsung.com> Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
2005-11-06[MTD] OneNAND: Add generic platform driverKyungmin Park
Signed-off-by: Kyungmin Park <kyungmin.park@samsung.com> Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
2005-11-06[MTD] maps/ixp4xx: remove platform specific bitsDavid Vrabel
- Intel chip driver has a reboot notifier so no need to reset the chip here. - Don't play with chip selects (platform code should do this if necessary). Signed-off-by: David Vrabel <dvrabel@arcom.com> Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
2005-11-06[JFFS2] Return real jffs2_sum_init() error codeFerenc Havasi
Signed-off-by: Ferenc Havasi <havasi@inf.u-szeged.hu> Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
2005-11-06[JFFS2] Add erase block summary support (mount time improvement)Ferenc Havasi
The goal of summary is to speed up the mount time. Erase block summary (EBS) stores summary information at the end of every (closed) erase block. It is no longer necessary to scan all nodes separetly (and read all pages of them) just read this "small" summary, where every information is stored which is needed at mount time. This summary information is stored in a JFFS2_FEATURE_RWCOMPAT_DELETE. During the mount process if there is no summary info the orignal scan process will be executed. EBS works with NAND and NOR flashes, too. There is a user space tool called sumtool to generate this summary information for a JFFS2 image. Signed-off-by: Ferenc Havasi <havasi@inf.u-szeged.hu> Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
2005-11-06[MTD] OneNAND: Remove experimental Kconfig dependencyKyungmin Park
Signed-off-by: Kyungmin Park <kyungmin.park@samsung.com> Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
2005-11-06[PATCH] OneNAND: Fix bug in write verifyKyungmin Park
- Remove unused block, page parameters - Add constant instead of runtime value Signed-off-by: Kyungmin Park <kyungmin.park@samsung.com> Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
2005-11-06[PATCH] OneNAND: Add simulatorKyungmin Park
Signed-off-by: Kyungmin Park <kyungmin.park@samsung.com> Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
2005-11-06[PATCH] OneNAND: Update OMAP OneNAND mapping using device driver modelKyungmin Park
- Update OMAP OneNAND mapping file using device driver model - Remove board specific macro and values. Signed-off-by: Kyungmin Park <kyungmin.park@samsung.com> Signed-off-by: Thomas Gleixner <tglx@linutronix.de>