| Age | Commit message (Collapse) | Author |
|---|
|
Card detect for sdhci on Cubox is connected to the wrong pin
(sdio1_cd instead of sdio0_cd). With support for cd-gpios and
pinctrl add the corresponding properties to DT for Cubox.
Signed-off-by: Sebastian Hesselbarth <sebastian.hesselbarth@gmail.com>
Signed-off-by: Jason Cooper <jason@lakedaemon.net>
|
|
Note that the pinctrl conversion also fixes GPIO support for ns2 boards.
Since commit f9e75922: "ARM: Kirkwood: Make use of mvebu pincltl and
gpio", the mvbu_gpio driver is used for DT boards. As mvbu_gpio relies
on the pinctrl driver, then a pinctrl definition must be given to allow
the GPIO configuration.
Signed-off-by: Simon Guinot <simon.guinot@sequanux.org>
Acked-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: Jason Cooper <jason@lakedaemon.net>
|
|
The Armada XP GPIO controller has two ways of notifying interrupts:
using global interrupts or using per-CPU interrupts. In an attempt to
use the best available features, the 'marvell,armadaxp-gpio'
compatible string selects a variant of the gpio-mvebu driver that
makes use of the per-CPU interrupts.
Unfortunately, this doesn't work properly in a SMP context, because we
fall into cases where the GPIO interrupt is enabled on CPU X at the
GPIO controller level, but on CPU Y at the interrupt controller
level. It is not yet clear how to fix that easily.
So for 3.8, our approach is to switch to global interrupts for GPIOs,
so that we do not fall into this per-CPU interrupts problem.
This patch therefore fixes GPIO interrupts on Armada XP
platforms. Without this patch, GPIO interrupts simply do not work
reliably, because their proper operation depends on which CPU the code
requesting the interrupt is running.
Signed-off-by: Thomas Petazzoni <thomas.petazzoni@free-electrons.com>
Signed-off-by: Jason Cooper <jason@lakedaemon.net>
|
|
With the ability to pass clocks through DT, now make the pdma
clock of dove pinctrl mandatory. Otherwise, pinctrl will hang
the system when accessing some registers.
Signed-off-by: Sebastian Hesselbarth <sebastian.hesselbarth@gmail.com>
Signed-off-by: Jason Cooper <jason@lakedaemon.net>
|
|
During merge of the mvebu patches a clock gate for pinctrl was
lost. This patch just readds the clock gate.
Signed-off-by: Sebastian Hesselbarth <sebastian.hesselbarth@gmail.com>
Signed-off-by: Jason Cooper <jason@lakedaemon.net>
|
|
When a channel fails to initialize, we release all ressources,
including clocks. However, a XOR unit is not necessarily associated to
a clock (some variants of Marvell SoCs have a clock for XOR units,
some don't), so we shouldn't unconditionally be releasing the clock.
Instead, just like we do in the mv_xor_remove() function, we should
check if one clock was found before releasing it.
Signed-off-by: Thomas Petazzoni <thomas.petazzoni@free-electrons.com>
Signed-off-by: Jason Cooper <jason@lakedaemon.net>
|
|
When mv_xor_channel_add() fails for one XOR channel, we jump to the
err_channel_add label to clean up all previous channels that had been
initialized correctly. Unfortunately, while handling this error
condition, we were disposing the IRQ mapping before calling
mv_xor_channel_remove() (which does the free_irq()), which is
incorrect.
Instead, do things properly in the reverse order of the
initialization: first remove the XOR channel (so that free_irq() is
done), and then dispose the IRQ mapping.
This avoids ugly warnings when for some reason one of the XOR channel
fails to initialize.
Signed-off-by: Thomas Petazzoni <thomas.petazzoni@free-electrons.com>
Signed-off-by: Jason Cooper <jason@lakedaemon.net>
|
|
The Armada XP MV78230 DT include file is missing a ; at the
end of the cpu node.
Reported-by: Thomas Petazzoni <thomas.petazzoni@free-electrons.com>
Signed-off-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: Jason Cooper <jason@lakedaemon.net>
|
|
We originally thought that the MV78230 variant of the Armada XP had
four Ethernet interfaces, like the other variants MV78260 and
MV78460. In fact, this is not true, and the MV78230 has only three
Ethernet interfaces.
So, the definitions of the Ethernet interfaces is now done as follows:
* armada-370-xp.dtsi: definitions of the first two interfaces, that
are common to Armada 370 and Armada XP
* armada-xp.dtsi: definition of the third interface, common to all
Armada XP variants.
* armada-xp-mv78260.dtsi and armada-xp-mv78460.dtsi: definition of
the fourth interface.
Signed-off-by: Thomas Petazzoni <thomas.petazzoni@free-electrons.com>
Signed-off-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: Jason Cooper <jason@lakedaemon.net>
|
|
Contrary to our understanding at the time armada-xp-mv78230.dtsi was
written, the MV78230 variant of the Armada XP SoC has two cores and
not one. This patch updates the .dtsi file to take into account this
reality.
Signed-off-by: Thomas Petazzoni <thomas.petazzoni@free-electrons.com>
Signed-off-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: Jason Cooper <jason@lakedaemon.net>
|
|
If the Orion WDT driver is built as a module, an opps occurs during
clk lookup when calling mvebu_clk_gating_get_src(). Remove the
inappropriate __init tag so the function is available for modules
after kernel init.
Signed-off-by: Joshua Coombs <josh.coombs@gmail.com>
Signed-off-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: Jason Cooper <jason@lakedaemon.net>
|
|
With the change to a DT based pinctrl/gpio driver, using gpio API
calls in board-*.c files no longer works, a dereferenced NULL pointer
exception occurs instead. By converting the GPIO code into a
fixed-regulator which gets probed later once pinctrl/gpio is
available, we avoid the exception.
Signed-off-by: Andrew Lunn <andrew@lunn.ch>
Tested-by: Stefan Peter <s.peter@mplch>
Signed-off-by: Jason Cooper <jason@lakedaemon.net>
|
|
We moved to declaring clk gates in DT. However, device which do not
yet have a DT binding need to have a clkdev alias. This was missing
for SDIO.
Signed-off-by: Andrew Lunn <andrew@lunn.ch>
Tested-by: Stefan Peter <s.peter@mplch>
Signed-off-by: Jason Cooper <jason@lakedaemon.net>
|
|
Clock Management of kirkwood has moved to DT clock providers.
However, TWSI1 has not yet been done.
This switches TWSI1 of 88f6282 to DT clock providers.
Signed-off-by: Nobuhiro Iwamatsu <iwamatsu@nigauri.org>
Signed-off-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: Jason Cooper <jason@lakedaemon.net>
|
|
Improve the documentation to clarify level vs edge triggered power off.
Improve the comments for level vs edge triggered power off.
Make use of gpio_is_valid().
Reported-by: Stephen Warren <swarren@wwwdotorg.org>
Signed-off-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: Jason Cooper <jason@lakedaemon.net>
|
|
Without the clock being held by a driver, it gets turned off at a bad
time causing the SoC to lockup. This is often during reboot.
Signed-off-by: Andrew Lunn <andrew@lunn.ch>
Tested-by: Stefan Peter <s.peter@mpl.ch>
Signed-off-by: Jason Cooper <jason@lakedaemon.net>
|
|
The UART controller used in the Armada 370 and Armada XP SoCs is the
Synopsys DesignWare 8250 (aka Synopsys DesignWare ABP UART). The
improper use of the ns16550 can lead to a kernel oops during boot if
a character is sent to the UART before the initialization of the
driver. The DW APB has an extra interrupt that gets raised when
writing to the LCR when busy. This explains why we need to use
dw-apb-uart driver to handle this.
Signed-off-by: Gregory CLEMENT <gregory.clement@free-electrons.com>
Signed-off-by: Jason Cooper <jason@lakedaemon.net>
|
|
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/cooloney/linux-leds
Pull LED fix from Bryan Wu.
* 'fixes-for-3.8' of git://git.kernel.org/pub/scm/linux/kernel/git/cooloney/linux-leds:
leds: leds-gpio: set devm_gpio_request_one() flags param correctly
|
|
commit a99d76f leds: leds-gpio: use gpio_request_one
changed the leds-gpio driver to use gpio_request_one() instead
of gpio_request() + gpio_direction_output()
Unfortunately, it also made a semantic change that breaks the
leds-gpio driver.
The gpio_request_one() flags parameter was set to:
GPIOF_DIR_OUT | (led_dat->active_low ^ state)
Since GPIOF_DIR_OUT is 0, the final flags value will just be the
XOR'ed value of led_dat->active_low and state.
This value were used to distinguish between HIGH/LOW output initial
level and call gpio_direction_output() accordingly.
With this new semantic gpio_request_one() will take the flags value
of 1 as a configuration of input direction (GPIOF_DIR_IN) and will
call gpio_direction_input() instead of gpio_direction_output().
int gpio_request_one(unsigned gpio, unsigned long flags, const char *label)
{
..
if (flags & GPIOF_DIR_IN)
err = gpio_direction_input(gpio);
else
err = gpio_direction_output(gpio,
(flags & GPIOF_INIT_HIGH) ? 1 : 0);
..
}
The right semantic is to evaluate led_dat->active_low ^ state and
set the output initial level explicitly.
Signed-off-by: Javier Martinez Canillas <javier.martinez@collabora.co.uk>
Reported-by: Arnaud Patard <arnaud.patard@rtp-net.org>
Tested-by: Ezequiel Garcia <ezequiel.garcia@free-electrons.com>
Signed-off-by: Bryan Wu <cooloney@gmail.com>
|
|
Pull watchdog fixes from Wim Van Sebroeck:
"This fixes some small errors in the new da9055 driver, eliminates a
compiler warning and adds DT support for the twl4030_wdt driver (so
that we can have multiple watchdogs with DT on the omap platforms)."
* git://www.linux-watchdog.org/linux-watchdog:
watchdog: twl4030_wdt: add DT support
watchdog: omap_wdt: eliminate unused variable and a compiler warning
watchdog: da9055: Don't update wdt_dev->timeout in da9055_wdt_set_timeout error path
watchdog: da9055: Fix invalid free of devm_ allocated data
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/helgaas/pci
Pull PCI updates from Bjorn Helgaas:
"Some fixes for v3.8. They include a fix for the new SR-IOV sysfs
management support, an expanded quirk for Ricoh SD card readers, a
Stratus DMI quirk fix, and a PME polling fix."
* tag '3.8-pci-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/helgaas/pci:
PCI: Reduce Ricoh 0xe822 SD card reader base clock frequency to 50MHz
PCI/PM: Do not suspend port if any subordinate device needs PME polling
PCI: Add PCIe Link Capability link speed and width names
PCI: Work around Stratus ftServer broken PCIe hierarchy (fix DMI check)
PCI: Remove spurious error for sriov_numvfs store and simplify flow
|
|
Commit 56c176c9cac9 ("UAPI: strip the _UAPI prefix from header guards
during header installation") strips the _UAPI prefix from header guards,
but only if there's a single space between the cpp directive and the
label.
Make it more flexible and able to handle tabs and multiple white space
characters.
Signed-off-by: David Howells <dhowell@redhat.com>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
|
|
Empty files can get deleted by the patch program, so remove empty Kbuild
files and their links from the parent Kbuilds.
Signed-off-by: David Howells <dhowells@redhat.com>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/tyhicks/ecryptfs
Pull ecryptfs fixes from Tyler Hicks:
"Two self-explanatory fixes and a third patch which improves
performance: when overwriting a full page in the eCryptfs page cache,
skip reading in and decrypting the corresponding lower page."
* tag 'ecryptfs-3.8-rc2-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/tyhicks/ecryptfs:
fs/ecryptfs/crypto.c: make ecryptfs_encode_for_filename() static
eCryptfs: fix to use list_for_each_entry_safe() when delete items
eCryptfs: Avoid unnecessary disk read and data decryption during writing
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/sage/ceph-client
Pull Ceph fixes from Sage Weil:
"Two of Alex's patches deal with a race when reseting server
connections for open RBD images, one demotes some non-fatal BUGs to
WARNs, and my patch fixes a protocol feature bit failure path."
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/sage/ceph-client:
libceph: fix protocol feature mismatch failure path
libceph: WARN, don't BUG on unexpected connection states
libceph: always reset osds when kicking
libceph: move linger requests sooner in kick_requests()
|
|
Sasha was fuzzing with trinity and reported the following problem:
BUG: sleeping function called from invalid context at kernel/mutex.c:269
in_atomic(): 1, irqs_disabled(): 0, pid: 6361, name: trinity-main
2 locks held by trinity-main/6361:
#0: (&mm->mmap_sem){++++++}, at: [<ffffffff810aa314>] __do_page_fault+0x1e4/0x4f0
#1: (&(&mm->page_table_lock)->rlock){+.+...}, at: [<ffffffff8122f017>] handle_pte_fault+0x3f7/0x6a0
Pid: 6361, comm: trinity-main Tainted: G W
3.7.0-rc2-next-20121024-sasha-00001-gd95ef01-dirty #74
Call Trace:
__might_sleep+0x1c3/0x1e0
mutex_lock_nested+0x29/0x50
mpol_shared_policy_lookup+0x2e/0x90
shmem_get_policy+0x2e/0x30
get_vma_policy+0x5a/0xa0
mpol_misplaced+0x41/0x1d0
handle_pte_fault+0x465/0x6a0
This was triggered by a different version of automatic NUMA balancing
but in theory the current version is vunerable to the same problem.
do_numa_page
-> numa_migrate_prep
-> mpol_misplaced
-> get_vma_policy
-> shmem_get_policy
It's very unlikely this will happen as shared pages are not marked
pte_numa -- see the page_mapcount() check in change_pte_range() -- but
it is possible.
To address this, this patch restores sp->lock as originally implemented
by Kosaki Motohiro. In the path where get_vma_policy() is called, it
should not be calling sp_alloc() so it is not necessary to treat the PTL
specially.
Signed-off-by: KOSAKI Motohiro <kosaki.motohiro@jp.fujitsu.com>
Tested-by: KOSAKI Motohiro <kosaki.motohiro@jp.fujitsu.com>
Signed-off-by: Mel Gorman <mgorman@suse.de>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/tytso/ext4
Pull ext4 bug fixes from Ted Ts'o:
"Various bug fixes for ext4. Perhaps the most serious bug fixed is one
which could cause file system corruptions when performing file punch
operations."
* tag 'ext4_for_linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tytso/ext4:
ext4: avoid hang when mounting non-journal filesystems with orphan list
ext4: lock i_mutex when truncating orphan inodes
ext4: do not try to write superblock on ro remount w/o journal
ext4: include journal blocks in df overhead calcs
ext4: remove unaligned AIO warning printk
ext4: fix an incorrect comment about i_mutex
ext4: fix deadlock in journal_unmap_buffer()
ext4: split off ext4_journalled_invalidatepage()
jbd2: fix assertion failure in jbd2_journal_flush()
ext4: check dioread_nolock on remount
ext4: fix extent tree corruption caused by hole punch
|
|
Remove the unused argument (formerly no_context) from mpol_parse_str()
and from mpol_to_str().
Signed-off-by: Hugh Dickins <hughd@google.com>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
|
|
Recently I suggested using "mount -o remount,mpol=local /tmp" in NUMA
mempolicy testing. Very nasty. Reading /proc/mounts, /proc/pid/mounts
or /proc/pid/mountinfo may then corrupt one bit of kernel memory, often
in a page table (causing "Bad swap" or "Bad page map" warning or "Bad
pagetable" oops), sometimes in a vm_area_struct or rbnode or somewhere
worse. "mpol=prefer" and "mpol=prefer:Node" are equally toxic.
Recent NUMA enhancements are not to blame: this dates back to 2.6.35,
when commit e17f74af351c "mempolicy: don't call mpol_set_nodemask() when
no_context" skipped mpol_parse_str()'s call to mpol_set_nodemask(),
which used to initialize v.preferred_node, or set MPOL_F_LOCAL in flags.
With slab poisoning, you can then rely on mpol_to_str() to set the bit
for node 0x6b6b, probably in the next page above the caller's stack.
mpol_parse_str() is only called from shmem_parse_options(): no_context
is always true, so call it unused for now, and remove !no_context code.
Set v.nodes or v.preferred_node or MPOL_F_LOCAL as mpol_to_str() might
expect. Then mpol_to_str() can ignore its no_context argument also,
the mpol being appropriately initialized whether contextualized or not.
Rename its no_context unused too, and let subsequent patch remove them
(that's not needed for stable backporting, which would involve rejects).
I don't understand why MPOL_LOCAL is described as a pseudo-policy:
it's a reasonable policy which suffers from a confusing implementation
in terms of MPOL_PREFERRED with MPOL_F_LOCAL. I believe this would be
much more robust if MPOL_LOCAL were recognized in switch statements
throughout, MPOL_F_LOCAL deleted, and MPOL_PREFERRED use the (possibly
empty) nodes mask like everyone else, instead of its preferred_node
variant (I presume an optimization from the days before MPOL_LOCAL).
But that would take me too long to get right and fully tested.
Signed-off-by: Hugh Dickins <hughd@google.com>
Cc: stable@vger.kernel.org
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
|
|
EPOLL_CTL_MOD sets the interest mask before calling f_op->poll() to
ensure events are not missed. Since the modifications to the interest
mask are not protected by the same lock as ep_poll_callback, we need to
ensure the change is visible to other CPUs calling ep_poll_callback.
We also need to ensure f_op->poll() has an up-to-date view of past
events which occured before we modified the interest mask. So this
barrier also pairs with the barrier in wq_has_sleeper().
This should guarantee either ep_poll_callback or f_op->poll() (or both)
will notice the readiness of a recently-ready/modified item.
This issue was encountered by Andreas Voellmy and Junchang(Jason) Wang in:
http://thread.gmane.org/gmane.linux.kernel/1408782/
Signed-off-by: Eric Wong <normalperson@yhbt.net>
Cc: Hans Verkuil <hans.verkuil@cisco.com>
Cc: Jiri Olsa <jolsa@redhat.com>
Cc: Jonathan Corbet <corbet@lwn.net>
Cc: Al Viro <viro@zeniv.linux.org.uk>
Cc: Davide Libenzi <davidel@xmailserver.org>
Cc: Hans de Goede <hdegoede@redhat.com>
Cc: Mauro Carvalho Chehab <mchehab@infradead.org>
Cc: David Miller <davem@davemloft.net>
Cc: Eric Dumazet <eric.dumazet@gmail.com>
Cc: Andrew Morton <akpm@linux-foundation.org>
Cc: Andreas Voellmy <andreas.voellmy@yale.edu>
Tested-by: "Junchang(Jason) Wang" <junchang.wang@yale.edu>
Cc: netdev@vger.kernel.org
Cc: linux-fsdevel@vger.kernel.org
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
|
|
Add DT support for twl4030_wdt. This is needed to get twl4030_wdt to
probe when booting with DT.
Signed-off-by: Aaro Koskinen <aaro.koskinen@iki.fi>
Signed-off-by: Wim Van Sebroeck <wim@iguana.be>
|
|
We forgot to delete this in the commit 4f4753d9 (watchdog: omap_wdt:
convert to devm_ functions), and as a result the following compilation
warning was introduced:
drivers/watchdog/omap_wdt.c: In function 'omap_wdt_remove':
drivers/watchdog/omap_wdt.c:299:19: warning: unused variable 'res' [-Wunused-variable]
Signed-off-by: Aaro Koskinen <aaro.koskinen@iki.fi>
Reviewed-by: Paul Walmsley <paul@pwsan.com>
Signed-off-by: Wim Van Sebroeck <wim@iguana.be>
|
|
error path
Otherwise, WDIOC_GETTIMEOUT returns wrong value if set_timeout fails.
This patch also removes unnecessary ret variable in da9055_wdt_ping function.
Signed-off-by: Axel Lin <axel.lin@ingics.com>
Signed-off-by: Wim Van Sebroeck <wim@iguana.be>
|
|
It is not required to free devm_ allocated data. Since kref_put
needs a valid release function, da9055_wdt_release_resources()
is not deleted.
Signed-off-by: Axel Lin <axel.lin@ingics.com>
Signed-off-by: Wim Van Sebroeck <wim@iguana.be>
|
|
Pull DRM update from Dave Airlie:
"This is a bit larger due to me not bothering to do anything since
before Xmas, and other people working too hard after I had clearly
given up.
It's got the 3 main x86 driver fixes pulls, and a bunch of tegra
fixes, doesn't fix the Ironlake bug yet, but that does seem to be
getting closer.
- radeon: gpu reset fixes and userspace packet support
- i915: watermark fixes, workarounds, i830/845 fix,
- nouveau: nvd9/kepler microcode fixes, accel is now enabled and
working, gk106 support
- tegra: misc fixes."
* 'drm-next' of git://people.freedesktop.org/~airlied/linux: (34 commits)
Revert "drm: tegra: protect DC register access with mutex"
drm: tegra: program only one window during modeset
drm: tegra: clean out old gem prototypes
drm: tegra: remove redundant tegra2_tmds_config entry
drm: tegra: protect DC register access with mutex
drm: tegra: don't leave clients host1x member uninitialized
drm: tegra: fix front_porch <-> back_porch mixup
drm/nve0/graph: fix fuc, and enable acceleration on all known chipsets
drm/nvc0/graph: fix fuc, and enable acceleration on GF119
drm/nouveau/bios: cache ramcfg strap on later chipsets
drm/nouveau/mxm: silence output if no bios data
drm/nouveau/bios: parse/display extra version component
drm/nouveau/bios: implement opcode 0xa9
drm/nouveau/bios: update gpio parsing apis to match current design
drm/nouveau: initial support for GK106
drm/radeon: add WAIT_UNTIL to evergreen VM safe reg list
drm/i915: disable shrinker lock stealing for create_mmap_offset
drm/i915: optionally disable shrinker lock stealing
drm/i915: fix flags in dma buf exporting
drm/radeon: add support for MEM_WRITE packet
...
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc
Pull late ARM cleanups for omap from Olof Johansson:
"From Tony Lindgren:
Here are few more patches to finish the omap changes for multiplatform
conversion that are not strictly fixes, but were too complex to do
with the dependencies during the merge window. Those are to move of
serial-omap.h to platform_data, and the removal of remaining
cpu_is_omap macro usage outside mach-omap2.
Then there are several trivial fixes for typos and few minimal
omap2plus_defconfig updates."
* tag 'omap-late-cleanups' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc:
arch/arm/mach-omap2/dpll3xxx.c: drop if around WARN_ON
OMAP2: Fix a typo - replace regist with register.
ARM/omap: use module_platform_driver macro
ARM: OMAP2+: PMU: Remove unused header
ARM: OMAP4: remove duplicated include from omap_hwmod_44xx_data.c
ARM: OMAP2+: omap2plus_defconfig: enable twl4030 SoC audio
ARM: OMAP2+: omap2plus_defconfig: Add tps65217 support
ARM: OMAP2+: enable devtmpfs and devtmpfs automount
ARM: OMAP2+: omap_twl: Change TWL4030_MODULE_PM_RECEIVER to TWL_MODULE_PM_RECEIVER
ARM: OMAP2+: Drop plat/cpu.h for omap2plus
ARM: OMAP: Split fb.c to remove last remaining cpu_is_omap usage
MAINTAINERS: Add an entry for omap related .dts files
|
|
Pull ARM SoC fixes from Olof Johansson:
"It's been quiet over the holidays, but we have had a couple of trivial
fixes coming in for the newly introduced sunxi platform; one to add it
to the multiplatform defconfig for build coverage, and one fixup for
device tree strings."
* tag 'fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc:
sunxi: Change the machine compatible string.
ARM: multi_v7_defconfig: Add ARCH_SUNXI
|
|
This reverts commit 83c0bcb694be31dcd6c04bdd935b96a95a0af548.
Lucas pointed out this was a mistake, and I missed the discussion,
so just revert it out to save a rebase.
Signed-off-by: Dave Airlie <airlied@redhat.com>
|
|
The intention is to program exactly WIN_A, not WIN_A and possibly
others.
Signed-off-by: Lucas Stach <dev@lynxeye.de>
Signed-off-by: Dave Airlie <airlied@redhat.com>
|
|
There is no gem.c anymore, those functions are implemented by the
drm_cma_helpers now.
Signed-off-by: Lucas Stach <dev@lynxeye.de>
Signed-off-by: Dave Airlie <airlied@redhat.com>
|
|
The 720p and 1080p entries are completely redundant, as we are matching
the table entries against <=pclk.
Also generalize the comment, as we are using those table entries even
when driving other modes than the standard TV ones.
Signed-off-by: Lucas Stach <dev@lynxeye.de>
Signed-off-by: Dave Airlie <airlied@redhat.com>
|
|
Window properties are programmed through a shared aperture and have to
happen atomically. Also we do the read-update-write dance on some of the
shared regs.
To make sure that different functions don't stumble over each other
protect the register access with a mutex.
Signed-off-by: Lucas Stach <dev@lynxeye.de>
Signed-off-by: Dave Airlie <airlied@redhat.com>
|
|
No real problem for now, as nothing is using this, but leaving it
unitialized is asking for trouble later on.
Signed-off-by: Lucas Stach <dev@lynxeye.de>
Signed-off-by: Dave Airlie <airlied@redhat.com>
|
|
Fixes wrong picture offset observed when using HDMI output with a
Technisat HD TV.
Signed-off-by: Lucas Stach <dev@lynxeye.de>
Acked-by: Mark Zhang <markz@nvidia.com>
Tested-by: Mark Zhang <markz@nvidia.com>
Signed-off-by: Dave Airlie <airlied@redhat.com>
|
|
git://people.freedesktop.org/~danvet/drm-intel into drm-next
Some fixes for 3.8:
- Watermark fixups from Chris Wilson (4 pieces).
- 2 snb workarounds, seem to be recently added to our internal DB.
- workaround for the infamous i830/i845 hang, seems now finally solid!
Based on Chris' fix for SNA, now also for UXA/mesa&old SNA.
- Some more fixlets for shrinker-pulls-the-rug issues (Chris&me).
- Fix dma-buf flags when exporting (you).
- Disable the VGA plane if it's enabled on lid open - similar fix in
spirit to the one I've sent you last weeek, BIOS' really like to mess
with the display when closing the lid (awesome debug work from Krzysztof
Mazur).
* 'drm-intel-fixes' of git://people.freedesktop.org/~danvet/drm-intel:
drm/i915: disable shrinker lock stealing for create_mmap_offset
drm/i915: optionally disable shrinker lock stealing
drm/i915: fix flags in dma buf exporting
i915: ensure that VGA plane is disabled
drm/i915: Preallocate the drm_mm_node prior to manipulating the GTT drm_mm manager
drm: Export routines for inserting preallocated nodes into the mm manager
drm/i915: don't disable disconnected outputs
drm/i915: Implement workaround for broken CS tlb on i830/845
drm/i915: Implement WaSetupGtModeTdRowDispatch
drm/i915: Implement WaDisableHiZPlanesWhenMSAAEnabled
drm/i915: Prefer CRTC 'active' rather than 'enabled' during WM computations
drm/i915: Clear self-refresh watermarks when disabled
drm/i915: Double the cursor self-refresh latency on Valleyview
drm/i915: Fixup cursor latency used for IVB lp3 watermarks
|
|
into drm-next
Misc fixes for reset and new packets for userspace usage.
* 'drm-fixes-3.8' of git://people.freedesktop.org/~agd5f/linux:
drm/radeon: add WAIT_UNTIL to evergreen VM safe reg list
drm/radeon: add support for MEM_WRITE packet
drm/radeon: restore modeset late in GPU reset path
drm/radeon: avoid deadlock in pm path when waiting for fence
drm/radeon: don't leave fence blocked process on failed GPU reset
|
|
git://anongit.freedesktop.org/git/nouveau/linux-2.6 into drm-next
Fixes the accel support for nvd9 + kepler chipsets, also fixes GK106 support.
* 'drm-nouveau-fixes-3.8' of git://anongit.freedesktop.org/git/nouveau/linux-2.6:
drm/nve0/graph: fix fuc, and enable acceleration on all known chipsets
drm/nvc0/graph: fix fuc, and enable acceleration on GF119
drm/nouveau/bios: cache ramcfg strap on later chipsets
drm/nouveau/mxm: silence output if no bios data
drm/nouveau/bios: parse/display extra version component
drm/nouveau/bios: implement opcode 0xa9
drm/nouveau/bios: update gpio parsing apis to match current design
drm/nouveau: initial support for GK106
|
|
An unintended consequence of commit 4ae0a48b5efc ("mm: modify
pgdat_balanced() so that it also handles order-0") is that
wait_iff_congested() can now be called with NULL 'struct zone *'
producing kernel oops like this:
BUG: unable to handle kernel NULL pointer dereference
IP: [<ffffffff811542d9>] wait_iff_congested+0x59/0x140
This trivial patch fixes it.
Reported-by: Zhouping Liu <zliu@redhat.com>
Reported-and-tested-by: Sedat Dilek <sedat.dilek@gmail.com>
Cc: Andrew Morton <akpm@linux-foundation.org>
Cc: Mel Gorman <mgorman@suse.de>
Cc: Hugh Dickins <hughd@google.com>
Signed-off-by: Zlatko Calusic <zlatko.calusic@iskon.hr>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
|
|
From Maxime Ripard:
Fixes for the sunxi core to be merged in 3.8-rc2
* tag 'sunxi-fixes-for-3.8-rc2' of git://github.com/mripard/linux:
sunxi: Change the machine compatible string.
ARM: multi_v7_defconfig: Add ARCH_SUNXI
|
