| Age | Commit message (Collapse) | Author |
|---|
|
ssh://master.kernel.org/pub/scm/linux/kernel/git/linville/wireless-2.6
|
|
From: Steve Hodgson <shodgson@solarflare.com>
Commit 357d46a17e54c9a87e0e6ef3930ff4ab2d232b81 "sfc: QT202x: Remove
unreliable MMD check at initialisation" broke initialisation of the
SFE4002. efx_mdio_reset_mmd() returns a positive value rather than 0
on success. The above commit causes this value to be propagated up
by qt202x_reset_phy(), which is treated as a failure by its callers.
Change qt202x_reset_phy() to return 0 if successful.
The PCI layer treats >0 as "fail, but please call remove() anyway",
which means that unloading the driver would cause a crash. Add a
WARN_ON() on the failure path of efx_pci_probe() to provide early
warning if there are any other cases where we do this.
Signed-off-by: Ben Hutchings <bhutchings@solarflare.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
For hardware with IEEE80211_HW_HAS_RATE_CONTROL the rate controller is not
initialized. However, calling functions such as ieee80211_beacon_get result
in the rate_control_get_rate function getting called, which is accessing
(in this case uninitialized) rate control structures unconditionally.
Fix by exiting the function before setting the rates for HW with
IEEE80211_HW_HAS_RATE_CONTROL set. The initialization of the ieee80211_tx_info
struct is intentionally still executed.
Signed-off-by: Juuso Oikarinen <juuso.oikarinen@nokia.com>
Reviewed-by: Kalle Valo <kalle.valo@nokia.com>
Cc: stable@kernel.org
Signed-off-by: John W. Linville <linville@tuxdriver.com>
|
|
Currently we treat IGMPv3 reports as if it were an IGMPv2/v1 report.
This is broken as IGMPv3 reports are formatted differently. So we
end up suppressing a bogus multicast group (which should be harmless
as long as the leading reserved field is zero).
In fact, IGMPv3 does not allow membership report suppression so
we should simply ignore IGMPv3 membership reports as a host.
This patch does exactly that. I kept the case statement for it
so people won't accidentally add it back thinking that we overlooked
this case.
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Previous patch "use paged Rx" broke AMSDU Rx functionality. If an AP
sends out A-MSDU packets the station will crash. Fix it by linearizing
skbuff for AMSDU packet before handing it to mac80211 since mac80211
doesn't support paged skbuff.
This fixes http://bugzilla.intellinuxwireless.org/show_bug.cgi?id=2155
Reported-by: Norbert Preining <preining@logic.at>
Signed-off-by: Shanyu Zhao <shanyu.zhao@intel.com>
Acked-by: Zhu Yi <yi.zhu@intel.com>
Signed-off-by: Reinette Chatre <reinette.chatre@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
|
|
Make sure, that TCP has a nonzero RTT estimation after three-way
handshake. Currently, a listening TCP has a value of 0 for srtt,
rttvar and rto right after the three-way handshake is completed
with TCP timestamps disabled.
This will lead to corrupt RTO recalculation and retransmission
flood when RTO is recalculated on backoff reversion as introduced
in "Revert RTO on ICMP destination unreachable"
(f1ecd5d9e7366609d640ff4040304ea197fbc618).
This behaviour can be provoked by connecting to a server which
"responds first" (like SMTP) and rejecting every packet after
the handshake with dest-unreachable, which will lead to softirq
load on the server (up to 30% per socket in some tests).
Thanks to Ilpo Jarvinen for providing debug patches and to
Denys Fedoryshchenko for reporting and testing.
Changes since v3: Removed bad characters in patchfile.
Reported-by: Denys Fedoryshchenko <denys@visp.net.lb>
Signed-off-by: Damian Lukowski <damian@tvk.rwth-aachen.de>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/linville/wireless-2.6
|
|
This patch fixes two potential races in the velocity driver:
* Move the ACK and error handler to the interrupt handler. This fixes a
potential race with shared interrupts when the other device interrupts
before the NAPI poll handler has finished. As the velocity driver hasn't
acked it's own interrupt, it will then steal the interrupt from the
other device.
* Use spin_lock_irqsave in velocity_poll. In the current code, the
interrupt handler will deadlock if e.g., the NAPI poll handler is
executing when an interrupt (for another device) comes in since it
tries to take the already held lock.
Also unlock the spinlock only after enabling the interrupt in
velocity_poll.
The error path is moved to the interrupt handler since this is where the
ISR is checked now.
Signed-off-by: Simon Kagstrom <simon.kagstrom@netinsight.net>
Signed-off-by: Anders Grafstrom <anders.grafstrom@netinsight.net>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
velocity_set_coalesce touches ISR and some other sensitive registers not
covered by the rtnl lock, so take the velocity spinlock.
Signed-off-by: Simon Kagstrom <simon.kagstrom@netinsight.net>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Signed-off-by: Simon Kagstrom <simon.kagstrom@netinsight.net>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Add new RTL8187B device.
Signed-off-by: Larry Finger <Larry.Finger@lwfinger.net>
Cc: Stable <stable@kernel.org>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
|
|
The wrong pointer was tested.
Signed-off-by: Roel Kluin <roel.kluin@gmail.com>
Acked-by: Samuel Ortiz <sameo@linux.intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
|
|
Currently, PAE frames are not assigned proper sequence numbers.
Since sending PAE frames as part of aggregates breaks
crupto with several APs, they are sent as normal MPDUs.
Fix the seqeuence number issue by updating the frame with the
internal sequence number.
Tested-by: Felix Fietkau <nbd@openwrt.org>
Signed-off-by: Sujith <Sujith.Manoharan@atheros.com>
Cc: stable@kernel.org
Signed-off-by: John W. Linville <linville@tuxdriver.com>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/holtmann/bluetooth-2.6
|
|
Test the value that was just allocated rather than the previously tested one.
A simplified version of the semantic match that finds this problem is as
follows: (http://coccinelle.lip6.fr/)
// <smpl>
@r@
expression *x;
expression e;
identifier l;
@@
if (x == NULL || ...) {
... when forall
return ...; }
... when != goto l;
when != x = e
when != &x
*x == NULL
// </smpl>
Signed-off-by: Julia Lawall <julia@diku.dk>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
During the rc period, patches that are not bugfixes
should be done using the net-next tree.
Signed-off-by: Joe Perches <joe@perches.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
The action modules have been prefixed with 'act_', but the Kconfig
description was not changed.
Signed-off-by: Jan Luebbe <jluebbe@debian.org>
Acked-by: Jamal Hadi Salim <hadi@cyberus.ca>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Verify the HW checksum state for frames handed to GRO processing.
Signed-off-by: Divy Le Ray <divy@chelsio.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Kernel bugzilla #15239
On some workloads, it is quite possible to get a huge dst list to
process in dst_gc_task(), and trigger soft lockup detection.
Fix is to call cond_resched(), as we run in process context.
Reported-by: Pawel Staszewski <pstaszewski@itcare.pl>
Tested-by: Pawel Staszewski <pstaszewski@itcare.pl>
Signed-off-by: Eric Dumazet <eric.dumazet@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Reinette found the reason for the warnings that
happened occasionally when a hw-offloaded scan
finished; her description of the problem:
mac80211 will defer the handling of scan requests if it is
busy with management work at the time. The scan requests
are deferred and run after the work has completed. When
this occurs there are currently two problems.
* The scan request for hardware scan is not fully populated
with the band and channels to scan not initialized.
* When the scan is queued the state is not correctly updated
to reflect that a scan is in progress. The problem here is
that when the driver completes the scan and calls
ieee80211_scan_completed() a warning will be triggered
since mac80211 was not aware that a scan was in progress.
The reason is that the queued scan work will start
the hw scan right away when the hw_scan_req struct
has already been allocated. However, in the first
pass it will not have been filled, which happens
at the same time as setting the bits. To fix this,
simply move the allocation after the pending work
test as well, so that the first iteration of the
scan work will call __ieee80211_start_scan() even
in the hardware scan case.
Bug-identified-by: Reinette Chatre <reinette.chatre@intel.com>
Signed-off-by: Johannes Berg <johannes@sipsolutions.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
|
|
iwl_set_rxon_ht() only get called in iwl_post_associate(); which cause
possible incorrect ht configuration. Adding the call in iwl_mac_config() if
IEEE80211_CONF_CHANGE_CHANNEL flag is set to re-configure and send rxon
command.
Fixes
http://bugzilla.intellinuxwireless.org/show_bug.cgi?id=2146
Signed-off-by: Wey-Yi Guy <wey-yi.w.guy@intel.com>
Signed-off-by: Reinette Chatre <reinette.chatre@intel.com>
CC: stable@kernel.org
Signed-off-by: John W. Linville <linville@tuxdriver.com>
|
|
We only reply to probe request if either the requested SSID is the
broadcast SSID or if the requested SSID matches our own SSID. This
latter case was not properly handled since we were replying to different
SSID with the same length as our own SSID.
Signed-off-by: Benoit Papillault <benoit.papillault@free.fr>
Cc: stable@kernel.org
Signed-off-by: John W. Linville <linville@tuxdriver.com>
|
|
As noticed by Jon Masters <jonathan@jonmasters.org>, the conntrack hash
size is global and not per namespace, but modifiable at runtime through
/sys/module/nf_conntrack/hashsize. Changing the hash size will only
resize the hash in the current namespace however, so other namespaces
will use an invalid hash size. This can cause crashes when enlarging
the hashsize, or false negative lookups when shrinking it.
Move the hash size into the per-namespace data and only use the global
hash size to initialize the per-namespace value when instanciating a
new namespace. Additionally restrict hash resizing to init_net for
now as other namespaces are not handled currently.
Cc: stable@kernel.org
Signed-off-by: Patrick McHardy <kaber@trash.net>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
As per C99 6.2.4(2) when temporary table data goes out of scope,
the behaviour is undefined:
if (compat) {
struct foo tmp;
...
private = &tmp;
}
[dereference private]
Signed-off-by: Alexey Dobriyan <adobriyan@gmail.com>
Cc: stable@kernel.org
Signed-off-by: Patrick McHardy <kaber@trash.net>
|
|
Expectation hashtable size was simply glued to a variable with no code
to rehash expectations, so it was a bug to allow writing to it.
Make "expect_hashsize" readonly.
Signed-off-by: Alexey Dobriyan <adobriyan@gmail.com>
Cc: stable@kernel.org
Signed-off-by: Patrick McHardy <kaber@trash.net>
|
|
nf_conntrack_cachep is currently shared by all netns instances, but
because of SLAB_DESTROY_BY_RCU special semantics, this is wrong.
If we use a shared slab cache, one object can instantly flight between
one hash table (netns ONE) to another one (netns TWO), and concurrent
reader (doing a lookup in netns ONE, 'finding' an object of netns TWO)
can be fooled without notice, because no RCU grace period has to be
observed between object freeing and its reuse.
We dont have this problem with UDP/TCP slab caches because TCP/UDP
hashtables are global to the machine (and each object has a pointer to
its netns).
If we use per netns conntrack hash tables, we also *must* use per netns
conntrack slab caches, to guarantee an object can not escape from one
namespace to another one.
Signed-off-by: Eric Dumazet <eric.dumazet@gmail.com>
[Patrick: added unique slab name allocation]
Cc: stable@kernel.org
Signed-off-by: Patrick McHardy <kaber@trash.net>
|
|
As discovered by Jon Masters <jonathan@jonmasters.org>, the "untracked"
conntrack, which is located in the data section, might be accidentally
freed when a new namespace is instantiated while the untracked conntrack
is attached to a skb because the reference count it re-initialized.
The best fix would be to use a seperate untracked conntrack per
namespace since it includes a namespace pointer. Unfortunately this is
not possible without larger changes since the namespace is not easily
available everywhere we need it. For now move the untracked conntrack
initialization to the init_net setup function to make sure the reference
count is not re-initialized and handle cleanup in the init_net cleanup
function to make sure namespaces can exit properly while the untracked
conntrack is in use in other namespaces.
Cc: stable@kernel.org
Signed-off-by: Patrick McHardy <kaber@trash.net>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
The report descriptor is read by user space (via the Service
Discovery Protocol), so it is only available during the ioctl
to connect. However, the HID probe function that needs the
descriptor might not be called until a specific module is
loaded. Keep a copy of the descriptor so it is available for
later use.
Signed-off-by: Michael Poole <mdpoole@troilus.org>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
|
|
Add missing try_to_freeze() to one of the pktgen_thread_worker() code
paths so that it doesn't block suspend/hibernation.
Fixes http://bugzilla.kernel.org/show_bug.cgi?id=15006
Signed-off-by: Rafael J. Wysocki <rjw@sisk.pl>
Reported-and-tested-by: Ciprian Dorin Craciun <ciprian.craciun@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
This change corrects an issue that will cause false hangs when using either
82575 or 82580 in legacy interrupt mode. The issue is caused when there is
a slow traffic flow and an "ethtool -r" is executed while using legacy or
MSI interrupts. MSI-X is not affected by this issue due to the fact that
we were already reconfiguring the vectors after reset.
If possible it would be best to push this for net-2.6 since it is resolving
a bug but if that is not possible then net-next-2.6 will be fine.
Signed-off-by: Alexander Duyck <alexander.h.duyck@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
One ioctl has been forgotten when the BKL was push down into irnet_ppp
ioctl function.
Signed-off-by: Thadeu Lima de Souza Cascardo <cascardo@holoscopio.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Add the missing unlock_kernel in one ioctl operation.
Signed-off-by: Thadeu Lima de Souza Cascardo <cascardo@holoscopio.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
a developer had complained of getting lots of warnings:
"eth16 selects TX queue 98, but real number of TX queues is 64"
http://www.mail-archive.com/e1000-devel@lists.sourceforge.net/msg02200.html
As there was no follow up on that bug, I am submitting this
patch assuming that the other return points will not return
invalid txq's, and also that this fixes the bug (not tested).
Signed-off-by: Krishna Kumar <krkumar2@in.ibm.com>
Signed-off-by: Jesse Brandeburg <jesse.brandeburg@intel.com>
Acked-by: Peter P Waskiewicz Jr <peter.p.waskiewicz.jr@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Commit e5a43549f7a58509a91b299a51337d386697b92c (ixgbe: remove
skb_dma_map/unmap calls from driver) looks to have introduced a bug in
ixgbe_tx_map. If we get an error from a PCI DMA call, we loop backwards
through count until it becomes -1 and return that.
The caller of ixgbe_tx_map expects 0 on error, so return that instead.
Signed-off-by: Anton Blanchard <anton@samba.org>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
o context resources can be in used, while resource cleanup is in progress,
during fw recover.
o Null pointer execption can occur in send_cmd_desc, if fw recovery
module frees tx ring without rtnl lock.
o Same applies to ethtool register dump.
Signed-off-by: Amit Kumar Salecha <amit.salecha@qlogic.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
For NX2031, first try to scrub interrupt before requesting firmware
reset. Return statement was missing after scrubbbing interrupt.
Signed-off-by: Vernon Mauery <vernux@us.ibm.com>
Signed-off-by: Amit Kumar Salecha <amit.salecha@qlogic.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
When in sniff mode with a long interval time (1.28s) it can take 4+ seconds
to establish a SCO link. Fix by requesting active mode before requesting
SCO connection. This improves SCO setup time to ~500ms.
Bluetooth headsets that use a long interval time, and exhibit the long
SCO connection time include Motorola H790, HX1 and H17. They have a
CSR 2.1 chipset.
Verified this behavior and fix with host Bluetooth chipsets: BCM4329 and
TI1271.
2009-10-13 14:17:46.183722 > HCI Event: Mode Change (0x14) plen 6
status 0x00 handle 1 mode 0x02 interval 2048
Mode: Sniff
2009-10-13 14:17:53.436285 < HCI Command: Setup Synchronous Connection (0x01|0x0028) plen 17
handle 1 voice setting 0x0060
2009-10-13 14:17:53.445593 > HCI Event: Command Status (0x0f) plen 4
Setup Synchronous Connection (0x01|0x0028) status 0x00 ncmd 1
2009-10-13 14:17:57.788855 > HCI Event: Synchronous Connect Complete 0x2c) plen 17
status 0x00 handle 257 bdaddr 00:1A:0E:F1:A4:7F type eSCO
Air mode: CVSD
Signed-off-by: Nick Pelly <npelly@google.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
|
|
Signed-off-by: Yoichi Yuasa <yuasa@linux-mips.org>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
|
|
This fixes commit (38ff3e6bb987ec583268da8eb22628293095d43b) ("dccp_probe:
Fix module load dependencies between dccp and dccp_probe", from 15 Jan).
It fixes the construction of the first argument of try_then_request_module(),
where only valid return codes from the first argument should be returned.
What we do now is assign the result of register_jprobe() to ret, without
the side effect of the comparison.
Acked-by: Gerrit Renker <gerrit@erg.abdn.ac.uk>
Signed-off-by: Neil Horman <nhorman@tuxdriver.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
This fixes a bug introduced in commit de4ef86cfce60d2250111f34f8a084e769f23b16
("dccp: fix dccp rmmod when kernel configured to use slub", 17 Jan): the
vsnprintf used sizeof(slab_name_fmt), which became truncated to 4 bytes, since
slab_name_fmt is now a 4-byte pointer and no longer a 32-character array.
This lead to error messages such as
FATAL: Error inserting dccp: No buffer space available
>> kernel: [ 1456.341501] kmem_cache_create: duplicate cache cci
generated due to the truncation after the 3rd character.
Fixed for the moment by introducing a symbolic constant. Tested to fix the bug.
Signed-off-by: Gerrit Renker <gerrit@erg.abdn.ac.uk>
Acked-by: Neil Horman <nhorman@tuxdriver.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
The book keeping structure for transmit always had the flags value
cleared so transmit DMA maps were never released correctly.
Based on patch by Jarek Poplawski, problem observed by Michael Breuer.
Signed-off-by: Stephen Hemminger <shemminger@vyatta.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Netlink code does module autoload if protocol userspace is asking for is
not ready. However, module can dissapear right after it was autoloaded.
Example: modprobe/rmmod stress-testing and xfrm_user.ko providing NETLINK_XFRM.
netlink_create() in such situation _will_ create userspace socket and
_will_not_ pin module. Now if module was removed and we're going to call
->netlink_rcv into nothing:
BUG: unable to handle kernel paging request at ffffffffa02f842a
^^^^^^^^^^^^^^^^
modules are loaded near these addresses here
IP: [<ffffffffa02f842a>] 0xffffffffa02f842a
PGD 161f067 PUD 1623063 PMD baa12067 PTE 0
Oops: 0010 [#1] PREEMPT SMP DEBUG_PAGEALLOC
last sysfs file: /sys/devices/pci0000:00/0000:00:1f.2/host0/target0:0:0/0:0:0:0/block/sda/uevent
CPU 1
Pid: 11515, comm: ip Not tainted 2.6.33-rc5-netns-00594-gaaa5728-dirty #6 P5E/P5E
RIP: 0010:[<ffffffffa02f842a>] [<ffffffffa02f842a>] 0xffffffffa02f842a
RSP: 0018:ffff8800baa3db48 EFLAGS: 00010292
RAX: ffff8800baa3dfd8 RBX: ffff8800be353640 RCX: 0000000000000000
RDX: ffffffff81959380 RSI: ffff8800bab7f130 RDI: 0000000000000001
RBP: ffff8800baa3db58 R08: 0000000000000001 R09: 0000000000000000
R10: 0000000000000001 R11: 0000000000000001 R12: 0000000000000011
R13: ffff8800be353640 R14: ffff8800bcdec240 R15: ffff8800bd488010
FS: 00007f93749656f0(0000) GS:ffff880002300000(0000) knlGS:0000000000000000
CS: 0010 DS: 0000 ES: 0000 CR0: 000000008005003b
CR2: ffffffffa02f842a CR3: 00000000ba82b000 CR4: 00000000000006e0
DR0: 0000000000000000 DR1: 0000000000000000 DR2: 0000000000000000
DR3: 0000000000000000 DR6: 00000000ffff0ff0 DR7: 0000000000000400
Process ip (pid: 11515, threadinfo ffff8800baa3c000, task ffff8800bab7eb30)
Stack:
ffffffff813637c0 ffff8800bd488000 ffff8800baa3dba8 ffffffff8136397d
<0> 0000000000000000 ffffffff81344adc 7fffffffffffffff 0000000000000000
<0> ffff8800baa3ded8 ffff8800be353640 ffff8800bcdec240 0000000000000000
Call Trace:
[<ffffffff813637c0>] ? netlink_unicast+0x100/0x2d0
[<ffffffff8136397d>] netlink_unicast+0x2bd/0x2d0
netlink_unicast_kernel:
nlk->netlink_rcv(skb);
[<ffffffff81344adc>] ? memcpy_fromiovec+0x6c/0x90
[<ffffffff81364263>] netlink_sendmsg+0x1d3/0x2d0
[<ffffffff8133975b>] sock_sendmsg+0xbb/0xf0
[<ffffffff8106cdeb>] ? __lock_acquire+0x27b/0xa60
[<ffffffff810a18c3>] ? might_fault+0x73/0xd0
[<ffffffff810a18c3>] ? might_fault+0x73/0xd0
[<ffffffff8106db22>] ? __lock_release+0x82/0x170
[<ffffffff810a190e>] ? might_fault+0xbe/0xd0
[<ffffffff810a18c3>] ? might_fault+0x73/0xd0
[<ffffffff81344c77>] ? verify_iovec+0x47/0xd0
[<ffffffff8133a509>] sys_sendmsg+0x1a9/0x360
[<ffffffff813c2be5>] ? _raw_spin_unlock_irqrestore+0x65/0x70
[<ffffffff8106aced>] ? trace_hardirqs_on+0xd/0x10
[<ffffffff813c2bc2>] ? _raw_spin_unlock_irqrestore+0x42/0x70
[<ffffffff81197004>] ? __up_read+0x84/0xb0
[<ffffffff8106ac95>] ? trace_hardirqs_on_caller+0x145/0x190
[<ffffffff813c207f>] ? trace_hardirqs_on_thunk+0x3a/0x3f
[<ffffffff8100262b>] system_call_fastpath+0x16/0x1b
Code: Bad RIP value.
RIP [<ffffffffa02f842a>] 0xffffffffa02f842a
RSP <ffff8800baa3db48>
CR2: ffffffffa02f842a
If module was quickly removed after autoloading, return -E.
Return -EPROTONOSUPPORT if module was quickly removed after autoloading.
Signed-off-by: Alexey Dobriyan <adobriyan@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
1. After sock_register() returns, it's possible to create sockets,
even if module still not initialized fully (blame generic module code
for that!)
2. Consequently, pfkey_create() can be called with pfkey_net_id still not
initialized which will BUG_ON in net_generic():
kernel BUG at include/net/netns/generic.h:43!
3. During netns shutdown, netns ops should be unregistered after
key manager unregistered because key manager calls can be triggered
from xfrm_user module:
general protection fault: 0000 [#1] PREEMPT SMP DEBUG_PAGEALLOC
pfkey_broadcast+0x111/0x210 [af_key]
pfkey_send_notify+0x16a/0x300 [af_key]
km_state_notify+0x41/0x70
xfrm_flush_sa+0x75/0x90 [xfrm_user]
4. Unregister netns ops after socket ops just in case and for symmetry.
Reported by Luca Tettamanti.
Signed-off-by: Alexey Dobriyan <adobriyan@gmail.com>
Tested-by: Luca Tettamanti <kronos.it@gmail.com>
Signed-off-by: Eric Dumazet <eric.dumazet@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
When processing a RFCOMM UA frame when the socket is closed and we were
not the RFCOMM initiator would cause rfcomm_session_put() to be called
twice during rfcomm_process_rx(). This would cause a kernel panic in
rfcomm_session_close() then.
This could be easily reproduced during disconnect with devices such as
Motorola H270 that send RFCOMM UA followed quickly by L2CAP disconnect
request. This trace for this looks like:
2009-09-21 17:22:37.788895 < ACL data: handle 1 flags 0x02 dlen 8
L2CAP(d): cid 0x0041 len 4 [psm 3]
RFCOMM(s): DISC: cr 0 dlci 20 pf 1 ilen 0 fcs 0x7d
2009-09-21 17:22:37.906204 > HCI Event: Number of Completed Packets (0x13) plen 5
handle 1 packets 1
2009-09-21 17:22:37.933090 > ACL data: handle 1 flags 0x02 dlen 8
L2CAP(d): cid 0x0040 len 4 [psm 3]
RFCOMM(s): UA: cr 0 dlci 20 pf 1 ilen 0 fcs 0x57
2009-09-21 17:22:38.636764 < ACL data: handle 1 flags 0x02 dlen 8
L2CAP(d): cid 0x0041 len 4 [psm 3]
RFCOMM(s): DISC: cr 0 dlci 0 pf 1 ilen 0 fcs 0x9c
2009-09-21 17:22:38.744125 > HCI Event: Number of Completed Packets (0x13) plen 5
handle 1 packets 1
2009-09-21 17:22:38.763687 > ACL data: handle 1 flags 0x02 dlen 8
L2CAP(d): cid 0x0040 len 4 [psm 3]
RFCOMM(s): UA: cr 0 dlci 0 pf 1 ilen 0 fcs 0xb6
2009-09-21 17:22:38.783554 > ACL data: handle 1 flags 0x02 dlen 12
L2CAP(s): Disconn req: dcid 0x0040 scid 0x0041
Avoid calling rfcomm_session_put() twice by skipping this call
in rfcomm_recv_ua() if the socket is closed.
Signed-off-by: Nick Pelly <npelly@google.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
|
|
With the commit 9e726b17422bade75fba94e625cd35fd1353e682 the
rfcomm_session_put() gets accidentially called from a timeout
callback and results in this:
BUG: sleeping function called from invalid context at net/core/sock.c:1897
in_atomic(): 1, irqs_disabled(): 0, pid: 0, name: swapper
Pid: 0, comm: swapper Tainted: P 2.6.32 #31
Call Trace:
<IRQ> [<ffffffff81036455>] __might_sleep+0xf8/0xfa
[<ffffffff8138ef1d>] lock_sock_nested+0x29/0xc4
[<ffffffffa03921b3>] lock_sock+0xb/0xd [l2cap]
[<ffffffffa03948e6>] l2cap_sock_shutdown+0x1c/0x76 [l2cap]
[<ffffffff8106adea>] ? clockevents_program_event+0x75/0x7e
[<ffffffff8106bea2>] ? tick_dev_program_event+0x37/0xa5
[<ffffffffa0394967>] l2cap_sock_release+0x27/0x67 [l2cap]
[<ffffffff8138c971>] sock_release+0x1a/0x67
[<ffffffffa03d2492>] rfcomm_session_del+0x34/0x53 [rfcomm]
[<ffffffffa03d24c5>] rfcomm_session_put+0x14/0x16 [rfcomm]
[<ffffffffa03d28b4>] rfcomm_session_timeout+0xe/0x1a [rfcomm]
[<ffffffff810554a8>] run_timer_softirq+0x1e2/0x29a
[<ffffffffa03d28a6>] ? rfcomm_session_timeout+0x0/0x1a [rfcomm]
[<ffffffff8104e0f6>] __do_softirq+0xfe/0x1c5
[<ffffffff8100e8ce>] ? timer_interrupt+0x1a/0x21
[<ffffffff8100cc4c>] call_softirq+0x1c/0x28
[<ffffffff8100e05b>] do_softirq+0x33/0x6b
[<ffffffff8104daf6>] irq_exit+0x36/0x85
[<ffffffff8100d7a9>] do_IRQ+0xa6/0xbd
[<ffffffff8100c493>] ret_from_intr+0x0/0xa
<EOI> [<ffffffff812585b3>] ? acpi_idle_enter_bm+0x269/0x294
[<ffffffff812585a9>] ? acpi_idle_enter_bm+0x25f/0x294
[<ffffffff81373ddc>] ? cpuidle_idle_call+0x97/0x107
[<ffffffff8100aca0>] ? cpu_idle+0x53/0xaa
[<ffffffff81429006>] ? rest_init+0x7a/0x7c
[<ffffffff8177bc8c>] ? start_kernel+0x389/0x394
[<ffffffff8177b29c>] ? x86_64_start_reservations+0xac/0xb0
[<ffffffff8177b384>] ? x86_64_start_kernel+0xe4/0xeb
To fix this, the rfcomm_session_put() needs to be moved out of
rfcomm_session_timeout() into rfcomm_process_sessions(). In that
context it is perfectly fine to sleep and disconnect the socket.
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
Tested-by: David John <davidjon@xenontk.org>
|
|
This fixes a CONFIG_SSB_SDIOHOST typo.
Signed-off-by: Michael Buesch <mb@bu3sch.de>
Reported-by: Christoph Egger <siccegge@stud.informatik.uni-erlangen.de>
Tested-By: Albert Herranz <albert_herranz@yahoo.es>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
|
|
Commit c7ab5ef9bcd281135c21b4732c9be779585181be entitled "b43: implement
short slot and basic rate handling" reduced the transmit throughput for
my BCM4311 device from 18 Mb/s to 0.7 Mb/s. The basic rate handling
portion is OK, the problem is in the short slot handling.
Prior to this change, the short slot enable/disable routines were never
called. Experimentation showed that the critical part was changing the
value at offset 0x0010 in the shared memory. This is supposed to contain
the 802.11 Slot Time in usec, but if it is changed from its initial value
of zero, performance is destroyed. On the other hand, changing the value
in the MMIO register corresponding to the Interframe Slot Time increased
performance from 18 to 22 Mb/s. A BCM4306/3 also shows dramatic
improvement of the transmit rate from 5.3 to 19.0 Mb/s.
Other changes in the patch include removal of the magic number for the
MMIO register, and allowing the slot time to be set for any PHY operating
in the 2.4 GHz band. Previously, the routine was executed only for G PHYs.
Signed-off-by: Larry Finger <Larry.Finger@lwfinger.net>
Cc: Stable <stable@kernel.org> [Any stable version back through 2.6.28]
Signed-off-by: John W. Linville <linville@tuxdriver.com>
|
|
General Motors carkits that use LGE BT chipsets return this error code
when an eSCO is attempted, despite advertising eSCO support.
2009-08-13 14:41:39.755518 < HCI Command: Setup Synchronous Connection (0x01|0x0028) plen 17
handle 1 voice setting 0x0060
2009-08-13 14:41:39.757563 > HCI Event: Command Status (0x0f) plen 4
Setup Synchronous Connection (0x01|0x0028) status 0x00 ncmd 1
2009-08-13 14:41:39.789484 > HCI Event: Synchronous Connect Complete (0x2c) plen 17
status 0x1a handle 257 bdaddr 00:1E:B2:23:5E:B3 type eSCO
Error: Unsupported Remote Feature / Unsupported LMP Feature
Signed-off-by: Jaikumar Ganesh <jaikumar@google.com>
Signed-off-by: Nick Pelly <npelly@google.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
|
|
On Tue, Feb 02, 2010 at 02:57:14PM -0800, Greg KH (gregkh@suse.de) wrote:
> > There are at least two ways to fix it: using a big cannon and a small
> > one. The former way is to disable notification registration, since it is
> > not used by anyone at all. Second way is to check whether calling
> > process is root and its destination group is -1 (kind of priveledged
> > one) before command is dispatched to workqueue.
>
> Well if no one is using it, removing it makes the most sense, right?
>
> No objection from me, care to make up a patch either way for this?
Getting it is not used, let's drop support for notifications about
(un)registered events from connector.
Another option was to check credentials on receiving, but we can always
restore it without bugs if needed, but genetlink has a wider code base
and none complained, that userspace can not get notification when some
other clients were (un)registered.
Kudos for Sebastian Krahmer <krahmer@suse.de>, who found a bug in the
code.
Signed-off-by: Evgeniy Polyakov <zbr@ioremap.net>
Acked-by: Greg Kroah-Hartman <gregkh@suse.de>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/kaber/nf-2.6
|
