| Age | Commit message (Collapse) | Author |
|---|
|
The following patch implements the dynamic relocation processing for
PPC32 kernel. relocate() accepts the target virtual address and relocates
the kernel image to the same.
Currently the following relocation types are handled :
R_PPC_RELATIVE
R_PPC_ADDR16_LO
R_PPC_ADDR16_HI
R_PPC_ADDR16_HA
The last 3 relocations in the above list depends on value of Symbol indexed
whose index is encoded in the Relocation entry. Hence we need the Symbol
Table for processing such relocations.
Note: The GNU ld for ppc32 produces buggy relocations for relocation types
that depend on symbols. The value of the symbols with STB_LOCAL scope
should be assumed to be zero. - Alan Modra
Signed-off-by: Suzuki K. Poulose <suzuki@in.ibm.com>
Signed-off-by: Josh Poimboeuf <jpoimboe@linux.vnet.ibm.com>
Cc: Paul Mackerras <paulus@samba.org>
Cc: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Cc: Alan Modra <amodra@au1.ibm.com>
Cc: Kumar Gala <galak@kernel.crashing.org>
Cc: linuxppc-dev <linuxppc-dev@lists.ozlabs.org>
Signed-off-by: Josh Boyer <jwboyer@gmail.com>
|
|
DYNAMIC_MEMSTART(old RELOCATABLE) was restricted only to PPC_47x variants
of 44x. This patch enables DYNAMIC_MEMSTART for 440x based chipsets.
Signed-off-by: Suzuki K. Poulose <suzuki@in.ibm.com>
Cc: Josh Boyer <jwboyer@gmail.com>
Cc: Kumar Gala <galak@kernel.crashing.org>
Cc: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Cc: linux ppc dev <linuxppc-dev@lists.ozlabs.org>
Signed-off-by: Josh Boyer <jwboyer@gmail.com>
|
|
The current implementation of CONFIG_RELOCATABLE in BookE is based
on mapping the page aligned kernel load address to KERNELBASE. This
approach however is not enough for platforms, where the TLB page size
is large (e.g, 256M on 44x). So we are renaming the RELOCATABLE used
currently in BookE to DYNAMIC_MEMSTART to reflect the actual method.
The CONFIG_RELOCATABLE for PPC32(BookE) based on processing of the
dynamic relocations will be introduced in the later in the patch series.
This change would allow the use of the old method of RELOCATABLE for
platforms which can afford to enforce the page alignment (platforms with
smaller TLB size).
Changes since v3:
* Introduced a new config, NONSTATIC_KERNEL, to denote a kernel which is
either a RELOCATABLE or DYNAMIC_MEMSTART(Suggested by: Josh Boyer)
Suggested-by: Scott Wood <scottwood@freescale.com>
Tested-by: Scott Wood <scottwood@freescale.com>
Signed-off-by: Suzuki K. Poulose <suzuki@in.ibm.com>
Cc: Scott Wood <scottwood@freescale.com>
Cc: Kumar Gala <galak@kernel.crashing.org>
Cc: Josh Boyer <jwboyer@gmail.com>
Cc: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Cc: linux ppc dev <linuxppc-dev@lists.ozlabs.org>
Signed-off-by: Josh Boyer <jwboyer@gmail.com>
|
|
We have an array of 16 entries and a loop of 32 iterations... oops.
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
|
|
the RMO.
As the kernels and initrd's get bigger boot-loaders and possibly
kexec-tools will need to place the initrd outside the RMO. When this
happens we end up with no lowmem and the boot doesn't get very far.
Only use initrd_end as the limit for alloc_bottom if it's inside the
RMO.
Signed-off-by: Paul Mackerras <paulus@samba.org>
Signed-off-by: Tony Breeds <tony@bakeyournoodle.com>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
|
|
We support 16TB of user address space and half a million contexts
so update the comment to reflect this.
Signed-off-by: Anton Blanchard <anton@samba.org>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
|
|
Commit d57af9b (taskstats: use real microsecond granularity for CPU times)
renamed msecs_to_cputime to usecs_to_cputime, but failed to update all
numbers on the way. This causes nonsensical cpu idle/iowait values to be
displayed in /proc/stat (the only user of usecs_to_cputime so far).
This also renames __cputime_msec_factor to __cputime_usec_factor, adapting
its value and using it directly in cputime_to_usecs instead of doing two
multiplications.
Signed-off-by: Andreas Schwab <schwab@linux-m68k.org>
Acked-by: Anton Blanchard <anton@samba.org>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
|
|
read_n_cells() cannot be marked as .devinit.text since it is referenced
from two functions that are not in that section: of_get_lmb_size() and
hot_add_drconf_scn_to_nid().
Signed-off-by: David Rientjes <rientjes@google.com>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
|
|
mark_reserved_regions_for_nid() is only called from do_init_bootmem(),
which is in .init.text, so it must be in the same section to avoid a
section mismatch warning.
Reported-by: Subrata Modak <subrata@linux.vnet.ibm.com>
Signed-off-by: David Rientjes <rientjes@google.com>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
|
|
PPC64 uses long long for u64 in the kernel, but powerpc's asm/types.h
prevents 64-bit userland from seeing this definition, instead defaulting
to u64 == long in userspace. Some user programs (e.g. kvmtool) may actually
want LL64, so this patch adds a check for __SANE_USERSPACE_TYPES__ so that,
if defined, int-ll64.h is included instead.
Signed-off-by: Matt Evans <matt@ozlabs.org>
Acked-by: Ingo Molnar <mingo@elte.hu>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
|
|
Implement a POWER7 optimised copy_to_user/copy_from_user using VMX.
For large aligned copies this new loop is over 10% faster, and for
large unaligned copies it is over 200% faster.
If we take a fault we fall back to the old version, this keeps
things relatively simple and easy to verify.
On POWER7 unaligned stores rarely slow down - they only flush when
a store crosses a 4KB page boundary. Furthermore this flush is
handled completely in hardware and should be 20-30 cycles.
Unaligned loads on the other hand flush much more often - whenever
crossing a 128 byte cache line, or a 32 byte sector if either sector
is an L1 miss.
Considering this information we really want to get the loads aligned
and not worry about the alignment of the stores. Microbenchmarks
confirm that this approach is much faster than the current unaligned
copy loop that uses shifts and rotates to ensure both loads and
stores are aligned.
We also want to try and do the stores in cacheline aligned, cacheline
sized chunks. If the store queue is unable to merge an entire
cacheline of stores then the L2 cache will have to do a
read/modify/write. Even worse, we will serialise this with the stores
in the next iteration of the copy loop since both iterations hit
the same cacheline.
Based on this, the new loop does the following things:
1 - 127 bytes
Get the source 8 byte aligned and use 8 byte loads and stores. Pretty
boring and similar to how the current loop works.
128 - 4095 bytes
Get the source 8 byte aligned and use 8 byte loads and stores,
1 cacheline at a time. We aren't doing the stores in cacheline
aligned chunks so we will potentially serialise once per cacheline.
Even so it is much better than the loop we have today.
4096 - bytes
If both source and destination have the same alignment get them both
16 byte aligned, then get the destination cacheline aligned. Do
cacheline sized loads and stores using VMX.
If source and destination do not have the same alignment, we get the
destination cacheline aligned, and use permute to do aligned loads.
In both cases the VMX loop should be optimal - we always do aligned
loads and stores and are always doing stores in cacheline aligned,
cacheline sized chunks.
To be able to use VMX we must be careful about interrupts and
sleeping. We don't use the VMX loop when in an interrupt (which should
be rare anyway) and we wrap the VMX loop in disable/enable_pagefault
and fall back to the existing copy_tofrom_user loop if we do need to
sleep.
The VMX breakpoint of 4096 bytes was chosen using this microbenchmark:
http://ozlabs.org/~anton/junkcode/copy_to_user.c
Since we are using VMX and there is a cost to saving and restoring
the user VMX state there are two broad cases we need to benchmark:
- Best case - userspace never uses VMX
- Worst case - userspace always uses VMX
In reality a userspace process will sit somewhere between these two
extremes. Since we need to test both aligned and unaligned copies we
end up with 4 combinations. The point at which the VMX loop begins to
win is:
0% VMX
aligned 2048 bytes
unaligned 2048 bytes
100% VMX
aligned 16384 bytes
unaligned 8192 bytes
Considering this is a microbenchmark, the data is hot in cache and
the VMX loop has better store queue merging properties we set the
breakpoint to 4096 bytes, a little below the unaligned breakpoints.
Some future optimisations we can look at:
- Looking at the perf data, a significant part of the cost when a
task is always using VMX is the extra exception we take to restore
the VMX state. As such we should do something similar to the x86
optimisation that restores FPU state for heavy users. ie:
/*
* If the task has used fpu the last 5 timeslices, just do a full
* restore of the math state immediately to avoid the trap; the
* chances of needing FPU soon are obviously high now
*/
preload_fpu = tsk_used_math(next_p) && next_p->fpu_counter > 5;
and
/*
* fpu_counter contains the number of consecutive context switches
* that the FPU is used. If this is over a threshold, the lazy fpu
* saving becomes unlazy to save the trap. This is an unsigned char
* so that after 256 times the counter wraps and the behavior turns
* lazy again; this to deal with bursty apps that only use FPU for
* a short time
*/
- We could create a paca bit to mirror the VMX enabled MSR bit and check
that first, avoiding multiple calls to calling enable_kernel_altivec.
That should help with iovec based system calls like readv.
- We could have two VMX breakpoints, one for when we know the user VMX
state is loaded into the registers and one when it isn't. This could
be a second bit in the paca so we can calculate the break points quickly.
- One suggestion from Ben was to save and restore the VSX registers
we use inline instead of using enable_kernel_altivec.
[BenH: Fixed a problem with preempt and fixed build without CONFIG_ALTIVEC]
Signed-off-by: Anton Blanchard <anton@samba.org>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
|
|
As of commit dd472da38, rwsem.h was moved into asm-generic.
This patch removes the arch file and points the build at
its new location.
Signed-off-by: Richard Kuo <rkuo@codeaurora.org>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
|
|
Conflicts:
arch/powerpc/platforms/40x/ppc40x_simple.c
|
|
The code for "powersurge" SMP would kick in and cause a crash
at boot due to the lack of a NULL test.
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
|
|
In the old days, we treated all interrupts from the legacy Apple home made
interrupt controllers as level, with a trick reading the "level" register
along with the "event" register to work arounds bugs where it would
occasionally fail to latch some events.
Doing so appeared to work fine for both level and edge interrupts.
Later on, we discovered in Darwin source the magic masks that define which
interrupts are actually level and which are edge, and implemented a
different algorithm, more similar to what Apple does, that treats those
differently.
I recently discovered however that this caused problems (including loss
of interrupts) with an old Wallstreet PowerBook when trying to use the
internal modem (connected to a cascaded controller).
It looks like some interrupts are treated as edge while they are really
level and I'm starting to seriously doubt the correctness of the Darwin
code (which has other obvious bugs when you read it, so ...)
This patch reverts to our original behaviour of treating everything as
a level interrupt. It appears to solve the problems with the modem on
the Wallstreet and everything else seems to be working properly as well.
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
|
|
This patch reworks & simplifies pmac_zilog handling of suspend/resume,
essentially removing all the specific code in there and using the
generic uart helpers.
This required properly registering the tty as a child of the macio (or platform)
device, so I had to delay the registration a bit (we used to register the ports
very very early). We still register the kernel console early though.
I removed a couple of unused or useless flags as well, relying on the
core to not call us when asleep. I also removed the essentially useless
interrupt mutex, simplifying the locking a bit.
I removed some code for handling unexpected interrupt which should never
be hit and could potentially be harmful (causing us to access a register
on a powered off SCC). We diable port interrupts on close always so there
should be no need to drain data on a closed port.
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
|
|
|
|
|
|
|
|
Based on original work by David 'Shaggy' Kleikamp.
Signed-off-by: Tony Breeds <tony@bakeyournoodle.com>
Signed-off-by: Josh Boyer <jwboyer@gmail.com>
|
|
Based on original work by David 'Shaggy' Kleikamp.
Signed-off-by: Tony Breeds <tony@bakeyournoodle.com>
Signed-off-by: Josh Boyer <jwboyer@gmail.com>
|
|
Needed for currituck support.
Signed-off-by: Tony Breeds <tony@bakeyournoodle.com>
Signed-off-by: Josh Boyer <jwboyer@gmail.com>
|
|
The upcomming currituck patches will need to do 64-bit shifts which will
fail with undefined symbol without this patch.
I looked at linking against libgcc but we can't guarantee that libgcc
was compiled with soft-float. Also Using ../lib/div64.S or
../kernel/misc_32.S, this will break the build as the .o's need to be
built with different flags for the bootwrapper vs the kernel. So for
now the easyest option is to just copy code from
arch/powerpc/kernel/misc_32.S I don't think this code changes too often ;P
Signed-off-by: Tony Breeds <tony@bakeyournoodle.com>
Signed-off-by: Josh Boyer <jwboyer@gmail.com>
|
|
CONFIG_PPC47x doesn't exist in Kconfig and no 476 processor calls this
function ppc44x_pin_tlb() as it has it's own ppc47x_pin_tlb().
This code is probably an artifact of the original 476 code that
shouldn't have made it upstream.
Signed-off-by: Christoph Egger <siccegge@cs.fau.de>
Signed-off-by: Tony Breeds <tony@bakeyournoodle.com>
Signed-off-by: Josh Boyer <jwboyer@gmail.com>
|
|
Needed if you want to use swiotlb, harmless otherwise.
Signed-off-by: Tony Breeds <tony@bakeyournoodle.com>
Signed-off-by: Josh Boyer <jwboyer@gmail.com>
|
|
Currituck doesn't need nor use SDR so aborting the pci setup if there is
no sdr-base would be bad.
Add a flag to ppc4xx_pciex_hwops for the backends to state if they need
SDR and then only complain and abort if they do and it's not found in
the device tree.
Signed-off-by: Tony Breeds <tony@bakeyournoodle.com>
Signed-off-by: Josh Boyer <jwboyer@gmail.com>
|
|
Signed-off-by: Tony Breeds <tony@bakeyournoodle.com>
Signed-off-by: Josh Boyer <jwboyer@gmail.com>
|
|
Most distros use it so we may as well enable it and get regular compile
testing.
Signed-off-by: Anton Blanchard <anton@samba.org>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
|
|
code.
When issuing a system reset we almost always oops in the oops_to_nvram
code because multiple CPUs are using the deflate work area. Add a
spinlock to protect it.
To play it safe I'm using trylock to avoid locking up if the NVRAM
code oopses. This means we might miss multiple CPUs oopsing at exactly
the same time but I think it's best to play it safe for now. Once we
are happy with the reliability we can change it to a full spinlock.
Signed-off-by: Anton Blanchard <anton@samba.org>
Acked-by: Jim Keniston <jkenisto@us.ibm.com>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
|
|
On most 68k Macs the SCC IRQ is an autovector interrupt and cannot be
masked. This can be a problem when pmac_zilog starts up.
For example, the serial debugging code in arch/m68k/kernel/head.S may be
used beforehand. It disables the SCC interrupts at the chip but doesn't
ack them. Then when a pmac_zilog port is used, the machine locks up with
"unexpected interrupt".
This can happen in pmz_shutdown() since the irq is freed before the
channel interrupts are disabled.
Fix this by clearing interrupt enable bits before the handler is
uninstalled. Also move the interrupt control bit flipping into a separate
pmz_interrupt_control() routine. Replace all instances of these operations
with calls to this routine. Omit the zssync() calls that seem to serve no
purpose.
Signed-off-by: Finn Thain <fthain@telegraphics.com.au>
Acked-by: Alan Cox <alan@linux.intel.com>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
|
|
This fixes a problem where a CPU thread coming out of nap mode can
think it has valid values in the nonvolatile GPRs (r14 - r31) as saved
away in power7_idle, but in fact the values have been trashed because
the thread was used for KVM in the mean time. The result is that the
thread crashes because code that called power7_idle (e.g.,
pnv_smp_cpu_kill_self()) goes to use values in registers that have
been trashed.
The bit field in SRR1 that tells whether state was lost only reflects
the most recent nap, which may not have been the nap instruction in
power7_idle. So we need an extra PACA field to indicate that state
has been lost even if SRR1 indicates that the most recent nap didn't
lose state. We clear this field when saving the state in power7_idle,
we set it to a non-zero value when we use the thread for KVM, and we
test it in power7_wakeup_noloss.
Signed-off-by: Paul Mackerras <paulus@samba.org>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
|
|
At present, on the powernv platform, if you off-line a CPU that was
online, and then try to on-line it again, the kernel generates a
warning message "OPAL Error -1 starting CPU n". Furthermore, if the
CPU is a secondary thread that was used by KVM while it was off-line,
the CPU fails to come online.
The first problem is fixed by only calling OPAL to start the CPU the
first time it is on-lined, as indicated by the cpu_start field of its
PACA being zero. The second problem is fixed by restoring the
cpu_start field to 1 instead of 0 when using the CPU within KVM.
Signed-off-by: Paul Mackerras <paulus@samba.org>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
|
|
The minimum RMO size field in ibm,client-architecture is currently
ignored, but a future firmware version will rectify that. Since we
always get at least 128MB of RMO right now, asking for 64MB is
likely to result in boot failures.
We should bump it to at least 128MB, but considering all the boot
issues we have on 128MB RMO boxes and all new machines have virtual
RMO, we may as well set our minimum to 256MB.
Signed-off-by: Anton Blanchard <anton@samba.org>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
|
|
With CONFIG_STRICT_DEVMEM=y, user space cannot read any part of /dev/mem.
Since this breaks librtas, punch a hole in /dev/mem to allow access to the
rmo_buffer that librtas needs.
Anton Blanchard reported the problem and helped with the fix.
A quick test for this patch:
# cat /proc/rtas/rmo_buffer
000000000f190000 10000
# python -c "print 0x000000000f190000 / 0x10000"
3865
# dd if=/dev/mem of=/tmp/foo count=1 bs=64k skip=3865
1+0 records in
1+0 records out
65536 bytes (66 kB) copied, 0.000205235 s, 319 MB/s
# dd if=/dev/mem of=/tmp/foo
dd: reading `/dev/mem': Operation not permitted
0+0 records in
0+0 records out
0 bytes (0 B) copied, 0.00022519 s, 0.0 kB/s
Signed-off-by: Sukadev Bhattiprolu <sukadev@linux.vnet.ibm.com>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
|
|
So I've had one of these for a while and it looks like the vendor never
bothered submitting the support upstream.
This adds it using ppc40x_simple and provides a device-tree.
There are some changes to the boot wrapper because the way u-boot works
on this thing, it seems to expect a multipart image with the kernel,
initrd and dtb in it.
The USB support is missing as it needs the yet unmerged driver for
the DWC OTG part and the GPIOs may need further definition in the dts.
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
|
|
Refresh ps3_defconfig to latest kernel sources and
change the options:
CONFIG_PPP=m to CONFIG_PPP=n.
CONFIG_NAMESPACES=y to CONFIG_NAMESPACES=n
CONFIG_NUMA=y to CONFIG_NUMA=n
Signed-off-by: Geoff Levand <geoff@infradead.org>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
|
|
Add an __init annotation to the ps3_smp_probe() routine.
Fixes build warnings like these when
CONFIG_DEBUG_SECTION_MISMATCH=y:
WARNING: Section mismatch in reference from the function .ps3_smp_probe()
Signed-off-by: Geoff Levand <geoff@infradead.org>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
|
|
Fix some PS3 repository.c build warnings when DEBUG is
defined. Also change most pr_debug calls to pr_devel calls.
Fixes warnings like these:
format '%lx' expects type 'long unsigned int', but argument 7 has type 'u64'
Signed-off-by: Geoff Levand <geoff@infradead.org>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
|
|
The lv1 hcall #91 should be named lv1_read_repository_node, and
not lv1_get_repository_node_value. Adjust the lv1 hcall table
and all calls.
Signed-off-by: Geoff Levand <geoff@infradead.org>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
|
|
The lv1_get_version_info hcall takes 2, not 1 output
arguments. Adjust the lv1 hcall table and all calls.
Usage:
int lv1_get_version_info(u64 *version_number, u64 *vendor_id)
Signed-off-by: Geoff Levand <geoff@infradead.org>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
|
|
The lv1_get_virtual_address_space_id_of_ppe hcall takes 0, not 1 input
arguments. Adjust the lv1 hcall table and all calls.
Signed-off-by: Geoff Levand <geoff@infradead.org>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
|
|
The lv1_net_stop_tx_dma and net_stop_rx_dma hcalls take 2, not 3 input
arguments. Adjust the lv1 hcall table and all calls.
Signed-off-by: Geoff Levand <geoff@infradead.org>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
|
|
General code cleanup for PS3 interrupt.c:
o Fill out comments for structure members.
o Move variables ipi_debug_brk_mask and lock from struct ps3_bmp to
struct ps3_private.
o Fix pr_debug build errors when DEBUG is defined.
o Convert bit operation to set_bit().
o Convert DBG macro from pr_debug to pr_devel
o Add new macro FAIL to replace pr_debug calls
Signed-off-by: Geoff Levand <geoff@infradead.org>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
|
|
capture code
We might enter the secondary CPU capture code twice, eg if we have to
unstick some CPUs with a system reset. In this case we don't want to
overwrite the state on CPUs that had made it into the capture code OK,
so use the cpus_state_saved cpumask for that and make it local to
crash_ipi_callback.
For controlling progress now use atomic_t cpus_in_crash to count how
many CPUs have made it into the kdump code, and time_to_dump to tell
everyone it's time to dump.
Signed-off-by: Anton Blanchard <anton@samba.org>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
|
|
If we enter the kdump code via system reset, wait a bit before
sending the IPI to capture all secondary CPUs. Without it we race
with the hypervisor that is issuing the system reset to each CPU.
If the IPI gets there first the system reset oops output then shows
the register state of the IPI handler which is not what we want.
I took the opportunity to add defines for all the various delays
we have. There's no need for cpu_relax when we are doing an mdelay,
so remove them too.
Signed-off-by: Anton Blanchard <anton@samba.org>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
|
|
I have an intermittent kdump fail where the hypervisor fails an H_EOI.
As a result our CPPR is never reset to 0xff and we no longer accept
interrupts.
This patch calls icp_hv_set_cppr to reset the CPPR if H_EOI fails,
fixing the kdump fail.
Signed-off-by: Anton Blanchard <anton@samba.org>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
|
|
We've had a 180 second panic timeout on ppc64 for as long as I
can remember. This patch reduces it to 10 seconds on pseries for a few
reasons:
- Almost all pseries machines have a hypervisor console so panic
output will be available in a scrollback buffer.
- The 180 seconds impacts our availability, users (other than
kernel hackers) just want the box to come back around so it
can continue its work.
- I spend a lot of my life staring at the 180 second panic timeout.
Many pseries machines take minutes to power cycle, so it's quicker
to sit through the 180 seconds than it is to power cycle.
Signed-off-by: Anton Blanchard <anton@samba.org>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
|
|
Our die() code was based off a very old x86 version. Update it to
mirror the current x86 code.
Signed-off-by: Anton Blanchard <anton@samba.org>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
|
|
Remove some unnecessary defines and fix some spelling mistakes.
Signed-off-by: Anton Blanchard <anton@samba.org>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
|
|
We can handle recursion caused by system reset by reusing the crash
shutdown fault handler.
Since we don't have an OS triggerable NMI, if all CPUs don't make it
into kdump then we tell the user to issue a system reset. However if
we have a panic timeout set we cannot wait forever and must continue
the kdump.
Signed-off-by: Anton Blanchard <anton@samba.org>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
|
