| Age | Commit message (Collapse) | Author |
|---|
|
Since uhci-hcd, ehci-hcd, and xhci-hcd support runtime PM, the .pm
field in their pci_driver structures should be protected by CONFIG_PM
rather than CONFIG_PM_SLEEP. The corresponding change has already
been made for ohci-hcd.
Without this change, controllers won't do runtime suspend if system
suspend or hibernation isn't enabled.
Signed-off-by: Alan Stern <stern@rowland.harvard.edu>
CC: Sarah Sharp <sarah.a.sharp@linux.intel.com>
CC: <stable@vger.kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
Commit 24f531371de1 (USB: EHCI: accept very late isochronous URBs)
changed the isochronous API provided by ehci-hcd. URBs submitted too
late, so that the time slots for all their packets have already
expired, are no longer rejected outright. Instead the submission is
accepted, and the URB completes normally with a -EXDEV error for each
packet. This is what client drivers expect.
This patch implements the same policy in ohci-hcd. The change is more
complicated than it was in ehci-hcd, because ohci-hcd doesn't scan for
isochronous completions in the same way as ehci-hcd does. Rather, it
depends on the hardware adding completed TDs to a "done queue". Some
OHCI controller don't handle this properly when a TD's time slot has
already expired, so we have to avoid adding such TDs to the schedule
in the first place. As a result, if the URB was submitted too late
then none of its TDs will get put on the schedule, so none of them
will end up on the done queue, so the driver will never realize that
the URB should be completed.
To solve this problem, the patch adds one to urb_priv->td_cnt for such
URBs, making it larger than urb_priv->length (td_cnt already gets set
to the number of TD's that had to be skipped because their slots have
expired). Each time an URB is given back, the finish_urb() routine
looks to see if urb_priv->td_cnt for the next URB on the same endpoint
is marked in this way. If so, it gives back the next URB right away.
This should be applied to all kernels containing commit 815fa7b91761
(USB: OHCI: fix logic for scheduling isochronous URBs).
Signed-off-by: Alan Stern <stern@rowland.harvard.edu>
CC: <stable@vger.kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
Commit 24f531371de1 (USB: EHCI: accept very late isochronous URBs)
changed the isochronous API provided by ehci-hcd. URBs submitted too
late, so that the time slots for all their packets have already
expired, are no longer rejected outright. Instead the submission is
accepted, and the URB completes normally with a -EXDEV error for each
packet. This is what client drivers expect.
This patch implements the same policy in uhci-hcd. It should be
applied to all kernels containing commit c44b225077bb (UHCI: implement
new semantics for URB_ISO_ASAP).
Signed-off-by: Alan Stern <stern@rowland.harvard.edu>
CC: <stable@vger.kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
Commit 24f531371de1 (USB: EHCI: accept very late isochronous URBs)
changed the isochronous API provided by ehci-hcd. URBs submitted too
late, so that the time slots for all their packets have already
expired, are no longer rejected outright. Instead the submission is
accepted, and the URB completes normally with a -EXDEV error for each
packet. This is what client drivers expect.
The same policy should be implemented in imx21-hcd, but I don't know
enough about the hardware to do it. As a second-best substitute, this
patch treats very late isochronous submissions as though the
URB_ISO_ASAP flag were set. I don't have any way to test this change,
unfortunately.
Signed-off-by: Alan Stern <stern@rowland.harvard.edu>
CC: Sascha Hauer <kernel@pengutronix.de>
CC: Martin Fuzzey <mfuzzey@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/sarah/xhci into usb-linus
Sarah writes:
xhci: Bug fixes for 3.12.
Hi Greg,
Here's five bug fixes for 3.12.
The first two bugs fix issues with the command cancellation handling,
which can lead to oopses or the xHCI driver attempting to handle
previously-completed transfers. People have been running into oopses
and odd behavior with command cancellation for a couple kernel releases,
so they're marked for stable.
The third patch fixes an issue with USB remote wakeup under xHCI that
can only be reproduced under ChromeOS. As discussed, this fix is not
urgent, and isn't marked for stable.
The fourth patch fixes a race condition between URB cancellation and
userspace clearing an endpoint stall. The fifth patch removes some
annoying dmesg spam when a USB 3.0 device is disconnected, by avoiding
sending a Set SEL request.
Sarah Sharp
|
|
To 2.02
Signed-off-by: Steve French <smfrench@gmail.com>
|
|
These flags were unused by cifs and since the EXT flags have
been moved to common code in uapi/linux/fs.h we won't need
to have a cifs specific copy.
Signed-off-by: Steve French <smfrench@gmail.com>
|
|
Since commit b5dc0d10 (drm/imx: kill firstopen callback) the following probe
failure is seen:
[drm] Supports vblank timestamp caching Rev 1 (10.10.2010).
[drm] No driver support for vblank timestamp query.
[drm] Initialized imx-drm 1.0.0 20120507 on minor 0
imx-ldb ldb.10: adding encoder failed with -16
imx-ldb: probe of ldb.10 failed with error -16
imx-ipuv3 2400000.ipu: IPUv3H probed
imx-ipuv3 2800000.ipu: IPUv3H probed
imx-ipuv3-crtc imx-ipuv3-crtc.0: adding crtc failed with -16.
imx-ipuv3-crtc: probe of imx-ipuv3-crtc.0 failed with error -16
imx-ipuv3-crtc imx-ipuv3-crtc.1: adding crtc failed with -16.
imx-ipuv3-crtc: probe of imx-ipuv3-crtc.1 failed with error -16
imx-ipuv3-crtc imx-ipuv3-crtc.2: adding crtc failed with -16.
imx-ipuv3-crtc: probe of imx-ipuv3-crtc.2 failed with error -16
imx-ipuv3-crtc imx-ipuv3-crtc.3: adding crtc failed with -16.
imx-ipuv3-crtc: probe of imx-ipuv3-crtc.3 failed with error -16
The reason for the probe failure is that now 'imxdrm->references' is incremented
early in imx_drm_driver_load(), so the following checks in imx_drm_add_crtc()
and imx_drm_add_encoder():
if (imxdrm->references) {
ret = -EBUSY;
goto err_busy;
}
,will always fail.
Instead of manually keeping the references in the imx-drm driver, let's use
drm->open_count.
After this patch, lvds panel is functional on a mx6qsabrelite board.
Signed-off-by: Fabio Estevam <fabio.estevam@freescale.com>
Acked-by: Sascha Hauer <s.hauer@pengutronix.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
Don't allow entry to iwctl_siwencodeext if device not open.
This fixes a race condition where wpa supplicant/network manager
enters the function when the device is already closed.
Signed-off-by: Malcolm Priestley <tvboxspy@gmail.com>
Cc: stable@vger.kernel.org # 3.8+
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
The vt6656 is prone to resetting on the usb bus.
It seems there is a race condition and wpa supplicant is
trying to open the device via iw_handlers before its actually
closed at a stage that the buffers are being removed.
The device is longer considered open when the
buffers are being removed. So move ~DEVICE_FLAGS_OPENED
flag to before freeing the device buffers.
Signed-off-by: Malcolm Priestley <tvboxspy@gmail.com>
Cc: stable@vger.kernel.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
There seems to be race condition that the device is ndo_start_xmit
at a point where the device is closing and apTD is NULL resulting
in dead lock.
Add a NULL check to apTD and return NULL to calling functions.
This is more likely on 64 bit systems.
Signed-off-by: Malcolm Priestley <tvboxspy@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
Checking the return of dev_alloc_skb as stated in the following bug: https://bugzilla.kernel.org/show_bug.cgi?id=60411
Signed-off-by: Iker Pedrosa <ikerpedrosam@gmail.com>
Reported-by: RUC_Soft_Sec rucsoftsec@gmail.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
The domain of Matt Mooneey's email doesn't exist anymore.
Setting usbip to Oprhan.
Signed-off-by: Tobias Polzer <tobias.polzer@fau.de>
Signed-off-by: Dominik Paulus <dominik.paulus@fau.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
sizeof when applied to a pointer typed expression gives the size of the
pointer.
Found by coccinelle spatch "misc/noderef.cocci"
Signed-off-by: Thomas Meyer <thomas@m3y3r.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
sizeof when applied to a pointer typed expression gives the size of the
pointer.
Found by coccinelle spatch "misc/noderef.cocci"
Signed-off-by: Thomas Meyer <thomas@m3y3r.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
sizeof when applied to a pointer typed expression gives the size of the
pointer.
Found by coccinelle spatch "misc/noderef.cocci"
Signed-off-by: Thomas Meyer <thomas@m3y3r.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
sizeof when applied to a pointer typed expression gives the size of the
pointer.
Found by coccinelle spatch "misc/noderef.cocci"
Signed-off-by: Thomas Meyer <thomas@m3y3r.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
This patch adds the staging/dgnc [DIGI NEO AND CLASSIC
PCI PRODUCTS] and staging/dgap [DIGI EPCA PCI PRODUCTS]
drivers to the MAINTAINERS file. I am listed as the
maintainer and the driverdev-devel list is the mailing
list for these drivers.
Signed-off-by: Lidza Louina <lidza.louina@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
sizeof when applied to a pointer typed expression gives the size of the
pointer.
Found by coccinelle spatch "misc/noderef.cocci"
Signed-off-by: Thomas Meyer <thomas@m3y3r.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/xen/tip
Pull Xen fixes from Konrad Rzeszutek Wilk:
"Bug-fixes and one update to the kernel-paramters.txt documentation.
- Fix PV spinlocks triggering jump_label code bug
- Remove extraneous code in the tpm front driver
- Fix ballooning out of pages when non-preemptible
- Fix deadlock when using a 32-bit initial domain with large amount
of memory
- Add xen_nopvpsin parameter to the documentation"
* tag 'stable/for-linus-3.12-rc2-tag' of git://git.kernel.org/pub/scm/linux/kernel/git/xen/tip:
xen/spinlock: Document the xen_nopvspin parameter.
xen/p2m: check MFN is in range before using the m2p table
xen/balloon: don't alloc page while non-preemptible
xen: Do not enable spinlocks before jump_label_init() has executed
tpm: xen-tpmfront: Remove the locality sysfs attribute
tpm: xen-tpmfront: Fix default durations
|
|
In
commit 81e49f811404f428a9d9a63295a0c267e802fa12
Author: Glauber Costa <glommer@openvz.org>
Date: Wed Aug 28 10:18:13 2013 +1000
i915: bail out earlier when shrinker cannot acquire mutex
SHRINK_STOP was added to tell the core shrinker code to bail out and
go to the next shrinker since the i915 shrinker couldn't acquire
required locks. But the SHRINK_STOP return code was added to the
->count_objects callback and not the ->scan_objects callback as it
should have been, resulting in tons of dmesg noise like
shrink_slab: i915_gem_inactive_scan+0x0/0x9c negative objects to delete nr=-xxxxxxxxx
Fix discusssed with Dave Chinner.
References: http://www.spinics.net/lists/intel-gfx/msg33597.html
Reported-by: Knut Petersen <Knut_Petersen@t-online.de>
Cc: Knut Petersen <Knut_Petersen@t-online.de>
Cc: Dave Chinner <david@fromorbit.com>
Cc: Glauber Costa <glommer@openvz.org>
Cc: Glauber Costa <glommer@gmail.com>
Cc: Andrew Morton <akpm@linux-foundation.org>
Cc: Rik van Riel <riel@redhat.com>
Cc: Mel Gorman <mgorman@suse.de>
Cc: Johannes Weiner <hannes@cmpxchg.org>
Cc: Michal Hocko <mhocko@suse.cz>
Acked-by: Dave Chinner <dchinner@redhat.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/device-mapper/linux-dm
Pull device-mapper fixes from Mike Snitzer:
"A few fixes for dm-snapshot, a 32 bit fix for dm-stats, a couple error
handling fixes for dm-multipath. A fix for the thin provisioning
target to not expose non-zero discard limits if discards are disabled.
Lastly, add two DM module parameters which allow users to tune the
emergency memory reserves that DM mainatins per device -- this helps
fix a long-standing issue for dm-multipath. The conservative default
reserve for request-based dm-multipath devices (256) has proven
problematic for users with many multipathed SCSI devices but
relatively little memory. To responsibly select a smaller value users
should use the new nr_bios tracepoint info (via commit 75afb352
"block: Add nr_bios to block_rq_remap tracepoint") to determine the
peak number of bios their workloads create"
* tag 'dm-3.12-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/device-mapper/linux-dm:
dm: add reserved_bio_based_ios module parameter
dm: add reserved_rq_based_ios module parameter
dm: lower bio-based mempool reservation
dm thin: do not expose non-zero discard limits if discards disabled
dm mpath: disable WRITE SAME if it fails
dm-snapshot: fix performance degradation due to small hash size
dm snapshot: workaround for a false positive lockdep warning
dm stats: fix possible counter corruption on 32-bit systems
dm mpath: do not fail path on -ENOSPC
|
|
Pull MIPS fixes from Ralf Baechle:
- Fix a comment
- A small cleanup the main purpose of which is to work around an
internal compiler error bug in certain Codesource toolchains.
* git://git.linux-mips.org/pub/scm/ralf/upstream-linus:
MIPS: mm: Move some checks out of 'for' loop in DMA operations
MIPS: cpu-features.h: s/MIPS53/MIPS64/
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/benh/powerpc
Pull powerpc fixes from Ben Herrenschmidt:
"Here are a few things for -rc2, this time it's all written by me so it
can only be perfect .... right ? :)
So we have the fix to call irq_enter/exit on the irq stack we've been
discussing, plus a cleanup on top to remove an unused (and broken)
stack limit tracking feature (well, make it 32-bit only in fact where
it is used and works properly).
Then we have two things that I wrote over the last couple of days and
made the executive decision to include just because I can (and I'm
sure you won't object .... right ?).
They fix a couple of annoying and long standing "issues":
- We had separate zImages for when booting via Open Firmware vs.
booting via a flat device-tree, while it's trivial to make one that
deals with both
- We wasted a ton of cycles spinning secondary CPUs uselessly at boot
instead of starting them when needed on pseries, thus contributing
significantly to global warming"
* 'merge' of git://git.kernel.org/pub/scm/linux/kernel/git/benh/powerpc:
powerpc/pseries: Do not start secondaries in Open Firmware
powerpc/zImage: make the "OF" wrapper support ePAPR boot
powerpc: Remove ksp_limit on ppc64
powerpc/irq: Run softirqs off the top of the irq stack
|
|
In gadget mode, musb->is_active should be set only when connected to the
host. musb_g_reset() already takes care of it.
Signed-off-by: Bin Liu <b-liu@ti.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip
Pull x86 fixes from Ingo Molnar:
"An EFI fix and two reboot-quirk fixes"
* 'x86-urgent-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
x86/reboot: Fix apparent cut-n-paste mistake in Dell reboot workaround
x86/reboot: Add quirk to make Dell C6100 use reboot=pci automatically
x86, efi: Don't map Boot Services on i386
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip
Pull scheduler fixes from Ingo Molnar:
"Three small fixes"
* 'sched-urgent-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
sched/balancing: Fix cfs_rq->task_h_load calculation
sched/balancing: Fix 'local->avg_load > busiest->avg_load' case in fix_small_imbalance()
sched/balancing: Fix 'local->avg_load > sds->avg_load' case in calculate_imbalance()
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip
Pull perf fixes from Ingo Molnar:
"Assorted standalone fixes"
* 'perf-urgent-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
perf/x86/intel: Add model number for Avoton Silvermont
perf: Fix capabilities bitfield compatibility in 'struct perf_event_mmap_page'
perf/x86/intel/uncore: Don't use smp_processor_id() in validate_group()
perf: Update ABI comment
tools lib lk: Uninclude linux/magic.h in debugfs.c
perf tools: Fix old GCC build error in trace-event-parse.c:parse_proc_kallsyms()
perf probe: Fix finder to find lines of given function
perf session: Check for SIGINT in more loops
perf tools: Fix compile with libelf without get_phdrnum
perf tools: Fix buildid cache handling of kallsyms with kcore
perf annotate: Fix objdump line parsing offset validation
perf tools: Fill in new definitions for madvise()/mmap() flags
perf tools: Sharpen the libaudit dependencies test
|
|
My old @it.uu.se email address is going away, so update relevant
files to point to my @gmail.com address instead. In sata_promise.c
just delete the address, people can get it from MAINTAINERS.
Signed-off-by: Mikael Pettersson <mikpe@it.uu.se>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
|
|
Signed-off-by: Lennox Wu <lennox.wu@gmail.com>
|
|
Signed-off-by: Lennox Wu <lennox.wu@gmail.com>
|
|
Signed-off-by: Lennox Wu <lennox.wu@gmail.com>
|
|
The modifications include:
1. Kconfig of Score: we don't support ioremap
2. Missed headfile including
3. There are some errors in other people's commit not checked by us, we fix it now
3.1 arch/score/kernel/entry.S: wrong instructions
3.2 arch/score/kernel/process.c : just some typos
Signed-off-by: Lennox Wu <lennox.wu@gmail.com>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/acme/linux into perf/urgent
Pull perf/urgent fixes from Arnaldo Carvalho de Melo:
* It was possible to use an uninitialized buffer when reading
kernel modules information and checking if the file was a
/proc/sys/kernel/kptr_restrict'ed one, fix for this from
Adrian Hunter.
* The libbfd demangler doesn't handle cloned functions (e.g. symbol.clone.NUM),
feed it unsuffixed symbol names, workaround from Andi Kleen.
* Fix segfault in 'perf trace' when processing perf.data files with PERF_RECORD_MMAP2
records, recently added but not handled in this tool, from David Ahern.
* Fix libdl related build in old systems like Fedora 12, from David Ahern.
* Make 'perf kmem' work again on non NUMA machines, fix from Jiri Olsa.
* Fix probing symbols with optimization suffix in 'perf probe' where some
operations that are entirely user level and involves vmlinux/DWARF were working
but when the symbol name was fed to the kprobes tracer, the in kernel code
would use /proc/kallsyms where the name had the suffix, from Masami Hiramatsu.
Signed-off-by: Arnaldo Carvalho de Melo <acme@redhat.com>
Signed-off-by: Ingo Molnar <mingo@kernel.org>
|
|
"APIC" should be "ACPI" here.
Signed-off-by: Hanjun Guo <hanjun.guo@linaro.org>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
|
|
These asics seem to use a mix of the DCE2.x and
DCE3.2 audio interfaces despite what the register spec
says.
Fixes:
https://bugs.freedesktop.org/show_bug.cgi?id=69729
https://bugs.freedesktop.org/show_bug.cgi?id=69671
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Cc: stable@vger.kernel.org
|
|
The libbfd C++ demangler doesn't seem to deal with cloned functions,
like symbol.clone.NUM.
Just strip the dot part before demangling and add it back later.
Signed-off-by: Andi Kleen <ak@linux.intel.com>
Link: http://lkml.kernel.org/r/1378998998-10802-1-git-send-email-andi@firstfloor.org
Signed-off-by: Arnaldo Carvalho de Melo <acme@redhat.com>
|
|
In machine__create_modules() the 'path' char array was used in a call to
symbol__restricted_filename() without always being populated.
Signed-off-by: Adrian Hunter <adrian.hunter@intel.com>
Cc: David Ahern <dsahern@gmail.com>
Cc: Frederic Weisbecker <fweisbec@gmail.com>
Cc: Jiri Olsa <jolsa@redhat.com>
Cc: Mike Galbraith <efault@gmx.de>
Cc: Namhyung Kim <namhyung@gmail.com>
Cc: Paul Mackerras <paulus@samba.org>
Cc: Peter Zijlstra <a.p.zijlstra@chello.nl>
Cc: Stephane Eranian <eranian@google.com>
Link: http://lkml.kernel.org/r/1379845338-29637-2-git-send-email-adrian.hunter@intel.com
[ Split patch removing unrelated conversion of sprintf to snprintf to perf/core ]
Signed-off-by: Arnaldo Carvalho de Melo <acme@redhat.com>
|
|
The ASID is represented as an unsigned int in mm_context_t and we
currently use the mmid assembler macro to access this element of the
struct. This should be accessed with a register of 32-bit width. If
the incorrect register width is used the ASID will be returned in
bits[32:63] of the register when running under big-endian.
Fix a use of the mmid macro in tlb.S to use a 32-bit access.
Signed-off-by: Will Deacon <will.deacon@arm.com>
Signed-off-by: Matthew Leach <matthew.leach@arm.com>
Signed-off-by: Catalin Marinas <catalin.marinas@arm.com>
|
|
get_user() is defined as a function macro in arm64, and trace_get_user()
calls it as followed:
get_user(ch, ptr++);
Since the second parameter occurs twice in the definition, 'ptr++' is
unexpectedly evaluated twice and trace_get_user() will generate a bogus
string from user-provided one. As a result, some ftrace sysfs operations,
like "echo FUNCNAME > set_ftrace_filter," hit this case and eventually fail.
This patch fixes the issue both in get_user() and put_user().
Signed-off-by: AKASHI Takahiro <takahiro.akashi@linaro.org>
[catalin.marinas@arm.com: added __user type annotation and s/optr/__p/]
Signed-off-by: Catalin Marinas <catalin.marinas@arm.com>
|
|
Fixes compile failure on Fedora 12.
Signed-off-by: David Ahern <dsahern@gmail.com>
Link: http://lkml.kernel.org/r/1379900700-5186-3-git-send-email-dsahern@gmail.com
Signed-off-by: Arnaldo Carvalho de Melo <acme@redhat.com>
|
|
Fix perf probe to probe on some symbols which have some optimzation
suffixes, e.g. ".part", ".isra", and ".constprop".
To fix this issue, instead of using the DIE name, perf probe uses the
symbol name found by dwfl_module_addrsym().
This also involves a perf probe --vars operation update which now shows
the symbol name instead of the DIE name.
Without this patch, putting a probe on an inlined function which was
compiled with a suffixed symbol will fail like this:
$ perf probe -v getname_flags
probe-definition(0): getname_flags
symbol:getname_flags file:(null) line:0 offset:0 return:0 lazy:(null)
0 arguments
Looking at the vmlinux_path (6 entries long)
Using /lib/modules/3.11.0+/build/vmlinux for symbols
found inline addr: 0xffffffff8119bb70
Probe point found: getname_flags+0
found inline addr: 0xffffffff8119bcb6
Probe point found: getname+6
found inline addr: 0xffffffff811a06a6
Probe point found: user_path_at_empty+6
find 3 probe_trace_events.
Opening /sys/kernel/debug//tracing/kprobe_events write=1
Added new events:
Writing event: p:probe/getname_flags getname_flags+0
Failed to write event: No such file or directory
Error: Failed to add events. (-1)
Because the debuginfo knows only the original (non suffix) symbol name,
it uses the original symbol for probe address but the kernel (kallsyms)
knows only suffixed symbol. Then, the kernel rejects that original
symbol.
This patch uses dwfl_module_addrsym() to get the correct (suffixed)
symbol from symtab when a probe point is found.
Reported-by: Arnaldo Carvalho de Melo <acme@ghostprotocols.net>
Signed-off-by: Masami Hiramatsu <masami.hiramatsu.pt@hitachi.com>
Cc: Ingo Molnar <mingo@redhat.com>
Cc: Paul Mackerras <paulus@samba.org>
Cc: Peter Zijlstra <a.p.zijlstra@chello.nl>
Link: http://lkml.kernel.org/r/20130925131616.31632.46658.stgit@udc4-manage.rcp.hitachi.co.jp
Signed-off-by: Arnaldo Carvalho de Melo <acme@redhat.com>
|
|
The check cpu_needs_post_dma_flush() in mips_dma_sync_sg_for_cpu() and
the check !plat_device_is_coherent() in mips_dma_sync_sg_for_device()
can be moved outside the for loop.
As a side effect, this also avoids a GCC bug that caused kernel compile
to fail with the error:
arch/mips/mm/dma-default.c: In function 'mips_dma_sync_sg_for_cpu':
arch/mips/mm/dma-default.c:316:1: internal compiler error: in add_insn_before, at emit-rtl.c:3852
This gcc failure is seen in Code Sourcery toolchains [e.g. gcc version
4.7.2 (Sourcery CodeBench Lite 2012.09-99)] after commit "MIPS: Optimize
current_cpu_type() for better code."
Signed-off-by: Jayachandran C <jchandra@broadcom.com>
Cc: linux-mips@linux-mips.org
Patchwork: https://patchwork.linux-mips.org/patch/5907/
Reviewed-by: Markos Chandras <markos.chandras@imgtec.com>
Tested-by: Markos Chandras <markos.chandras@imgtec.com>
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
|
|
Which disables in the ticketlock slowpath the Xen PV optimization's.
Useful for diagnosing issues and comparing benchmarks in
over-commit CPU scenarios.
Signed-off-by: Konrad Rzeszutek Wilk <konrad.wilk@oracle.com>
|
|
On hosts with more than 168 GB of memory, a 32-bit guest may attempt
to grant map an MFN that is error cannot lookup in its mapping of the
m2p table. There is an m2p lookup as part of m2p_add_override() and
m2p_remove_override(). The lookup falls off the end of the mapped
portion of the m2p and (because the mapping is at the highest virtual
address) wraps around and the lookup causes a fault on what appears to
be a user space address.
do_page_fault() (thinking it's a fault to a userspace address), tries
to lock mm->mmap_sem. If the gntdev device is used for the grant map,
m2p_add_override() is called from from gnttab_mmap() with mm->mmap_sem
already locked. do_page_fault() then deadlocks.
The deadlock would most commonly occur when a 64-bit guest is started
and xenconsoled attempts to grant map its console ring.
Introduce mfn_to_pfn_no_overrides() which checks the MFN is within the
mapped portion of the m2p table before accessing the table and use
this in m2p_add_override(), m2p_remove_override(), and mfn_to_pfn()
(which already had the correct range check).
All faults caused by accessing the non-existant parts of the m2p are
thus within the kernel address space and exception_fixup() is called
without trying to lock mm->mmap_sem.
This means that for MFNs that are outside the mapped range of the m2p
then mfn_to_pfn() will always look in the m2p overrides. This is
correct because it must be a foreign MFN (and the PFN in the m2p in
this case is only relevant for the other domain).
Signed-off-by: David Vrabel <david.vrabel@citrix.com>
Cc: Stefano Stabellini <stefano.stabellini@citrix.com>
Cc: Jan Beulich <JBeulich@suse.com>
--
v3: check for auto_translated_physmap in mfn_to_pfn_no_overrides()
v2: in mfn_to_pfn() look in m2p_overrides if the MFN is out of
range as it's probably foreign.
Signed-off-by: Konrad Rzeszutek Wilk <konrad.wilk@oracle.com>
Acked-by: Stefano Stabellini <stefano.stabellini@eu.citrix.com>
|
|
Bit 12 is undefined in any of the following cases:
- If the "NMI exiting" VM-execution control is 1 and the "virtual NMIs"
VM-execution control is 0.
- If the VM exit sets the valid bit in the IDT-vectoring information field
Signed-off-by: Gleb Natapov <gleb@redhat.com>
[Add parentheses around & within && - Paolo]
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
|
|
This seems to have been copied from the Optiplex 990 entry
above, but somoene forgot to change the ident text.
Signed-off-by: Dave Jones <davej@fedoraproject.org>
Link: http://lkml.kernel.org/r/20130925001344.GA13554@redhat.com
Signed-off-by: Ingo Molnar <mingo@kernel.org>
|
|
Starting secondary CPUs early on from Open Firmware and placing them
in a holding spin loop slows down the boot process significantly under
some hypervisors such as KVM.
This is also unnecessary when RTAS supports querying the CPU state
So let's not do it.
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
|
|
This makes the "OF" zImage wrapper (zImage.pseries, zImage.pmac,
zImage.maple) work if booted via a flat device-tree (ePAPR boot
mode), and thus potentially usable with kexec.
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
|
|
We've been keeping that field in thread_struct for a while, it contains
the "limit" of the current stack pointer and is meant to be used for
detecting stack overflows.
It has a few problems however:
- First, it was never actually *used* on 64-bit. Set and updated but
not actually exploited
- When switching stack to/from irq and softirq stacks, it's update
is racy unless we hard disable interrupts, which is costly. This
is fine on 32-bit as we don't soft-disable there but not on 64-bit.
Thus rather than fixing 2 in order to implement 1 in some hypothetical
future, let's remove the code completely from 64-bit. In order to avoid
a clutter of ifdef's, we remove the updates from C code completely
during interrupt stack switching, and instead maintain it from the
asm helper that is used to do the stack switching in the first place.
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
|
