| Age | Commit message (Collapse) | Author |
|---|
|
The "clk_pm_capable", "clk_pm_enable" and "bios_clk_state" fields in
the struct pcie_link_state only take 1-bit value. So those fields
don't need to be defined as unsigned int. This patch makes those
fields 1-bit, and cleans up some related code.
Acked-by: Shaohua Li <shaohua.li@intel.com>
Signed-off-by: Kenji Kaneshige <kaneshige.kenji@jp.fujitsu.com>
Signed-off-by: Jesse Barnes <jbarnes@virtuousgeek.org>
|
|
Clean up latency related data structures for ASPM.
- Introduce struct acpi_latency for exit latency and acceptable
latency management. With this change, struct endpoint_state is no
longer needed.
- We don't need to hold both upstream latency and downstream latency
in the current implementation.
Acked-by: Shaohua Li <shaohua.li@intel.com>
Signed-off-by: Kenji Kaneshige <kaneshige.kenji@jp.fujitsu.com>
Signed-off-by: Jesse Barnes <jbarnes@virtuousgeek.org>
|
|
The "support_state", "enabled_state" and "bios_aspm_state" fields in
the struct pcie_link_state take 2-bit value. So those fields don't
need to be defined as unsigned int. This patch makes those fields
2-bit, and cleans up some related code.
Acked-by: Shaohua Li <shaohua.li@intel.com>
Signed-off-by: Kenji Kaneshige <kaneshige.kenji@jp.fujitsu.com>
Signed-off-by: Jesse Barnes <jbarnes@virtuousgeek.org>
|
|
Fix a typo in struct pcie_link_state.
The "sibiling" field in the struct pcie_link_state should be
"sibling".
Acked-by: Shaohua Li <shaohua.li@intel.com>
Signed-off-by: Kenji Kaneshige <kaneshige.kenji@jp.fujitsu.com>
Signed-off-by: Jesse Barnes <jbarnes@virtuousgeek.org>
|
|
There is no way to interact with a physical PCI slot without
sysfs, so encode the dependency and prevent this build error:
drivers/pci/slot.c: In function 'pci_hp_create_module_link':
drivers/pci/slot.c:327: error: 'module_kset' undeclared
This patch _should_ make pci-sysfs.o depend on CONFIG_SYSFS too,
but we cannot (yet) because the PCI core merrily assumes the
existence of sysfs:
drivers/built-in.o: In function `pci_bus_add_device':
drivers/pci/bus.c:89: undefined reference to `pci_create_sysfs_dev_files'
drivers/built-in.o: In function `pci_stop_dev':
drivers/pci/remove.c:24: undefined reference to `pci_remove_sysfs_dev_files'
So do the minimal bit for now and figure out how to untangle it
later.
Reported-by: Randy Dunlap <randy.dunlap@oracle.com>
Acked-by: Randy Dunlap <randy.dunlap@oracle.com>
Reported-by: Stephen Rothwell <sfr@canb.auug.org.au>
Fix-suggested-by: Matthew Wilcox <matthew@wil.cx>
Signed-off-by: Alex Chiang <achiang@hp.com>
Signed-off-by: Jesse Barnes <jbarnes@virtuousgeek.org>
|
|
We have the 'pos' of the MSI capability at all locations which call
msi_set_enable(), so pass it to msi_set_enable() instead of making it
find the capability every time.
Reviewed-by: Kenji Kaneshige <kaneshige.kenji@jp.fujitsu.com>
Signed-off-by: Matthew Wilcox <willy@linux.intel.com>
Signed-off-by: Jesse Barnes <jbarnes@virtuousgeek.org>
|
|
Other functions use type bool, so use that for pci_enable_wake as well.
Signed-off-by: Frans Pop <elendil@planet.nl>
Signed-off-by: Jesse Barnes <jbarnes@virtuousgeek.org>
|
|
Issue a warning if _CRS returns too many resource descriptors to be
accommodated by the fixed size resource array instances. If there is no
transparent bridge on the root bus "too many" is the
PCI_BUS_NUM_RESOURCES size of the resource array. Otherwise, the last 3
slots of the resource array must be excluded making the maximum
(PCI_BUS_NUM_RESOURCES - 3).
The current code:
- is silent when _CRS returns too many resource descriptors and
- incorrectly allows use of the last 3 slots of the resource array
for a root bus with a transparent bridge
Signed-off-by: Gary Hade <garyhade@us.ibm.com>
Signed-off-by: Jesse Barnes <jbarnes@virtuousgeek.org>
|
|
Remove invalid comment of msi_mask_irq().
Reviewed-by: Matthew Wilcox <willy@linux.intel.com>
Signed-off-by: Kenji Kaneshige <kaneshige.kenji@jp.fujitsu.com>
Signed-off-by: Jesse Barnes <jbarnes@virtuousgeek.org>
|
|
If a PCI device is not power-manageable either by the platform, or
with the help of the native PCI PM interface, pci_target_state() will
return either PCI_D3hot, or PCI_POWER_ERROR for it, depending on
whether or not the device is configured to wake up the system. Alas,
none of these return values is correct, because each of them causes
pci_prepare_to_sleep() to return error code, although it should
complete successfully in such a case.
Fix this problem by making pci_target_state() always return PCI_D0
for devices that cannot be power managed.
Cc: stable@kernel.org
Signed-off-by: Rafael J. Wysocki <rjw@sisk.pl>
Signed-off-by: Jesse Barnes <jbarnes@virtuousgeek.org>
|
|
PCI-to-PCI Bridge 1.2 specifies that the Secondary Bus Reset bit can
force the assertion of RST# on the secondary interface, which can be
used to reset all devices including subordinates under this bus. This
can be used to reset a function if this function is the only device
under this bus.
Reviewed-by: Kenji Kaneshige <kaneshige.kenji@jp.fujitsu.com>
Signed-off-by: Yu Zhao <yu.zhao@intel.com>
Signed-off-by: Jesse Barnes <jbarnes@virtuousgeek.org>
|
|
PCI PM 1.2 specifies that the device will perform an internal reset upon
transitioning from D3hot to D0 when the NO_SOFT_RESET bit is clear. This
method can be used to reset a function if neither PCIe FLR nor PCI AF FLR
are supported.
Reviewed-by: Kenji Kaneshige <kaneshige.kenji@jp.fujitsu.com>
Signed-off-by: Yu Zhao <yu.zhao@intel.com>
Signed-off-by: Jesse Barnes <jbarnes@virtuousgeek.org>
|
|
This patch enhances the FLR functions:
1) remove disable_irq() so the shared IRQ won't be disabled.
2) replace the 1s wait with 100, 200 and 400ms wait intervals
for the Pending Transaction.
3) replace mdelay() with msleep().
4) add might_sleep().
5) lock the device to prevent PM suspend from accessing the CSRs
during the reset.
6) coding style fixes.
Reviewed-by: Kenji Kaneshige <kaneshige.kenji@jp.fujitsu.com>
Signed-off-by: Yu Zhao <yu.zhao@intel.com>
Signed-off-by: Jesse Barnes <jbarnes@virtuousgeek.org>
|
|
Debugging PCIE AER code can be very difficult because it is hard
to trigger various real hardware errors. This patch provide a
software based error injection tool, which can fake various PCIE
errors with a user space helper tool named "aer-inject". Which
can be gotten from:
http://www.kernel.org/pub/linux/kernel/people/yhuang/
The patch fakes AER error by faking some PCIE AER related
registers and an AER interrupt for specified the PCIE device.
Signed-off-by: Huang Ying <ying.huang@intel.com>
Signed-off-by: Jesse Barnes <jbarnes@virtuousgeek.org>
|
|
When a root port receives the same errors more than once before the
kernel process them, the Multiple Error Messages Received flags are set
by hardware. Because the root port could only save one kind of
correctable error source id and another uncorrectable error source id at
the same time, the second message sender id is lost if the 2 messages
are sent from 2 different devices. This patch makes the kernel search
all devices under the root port when multiple messages are received.
Reviewed-by: Andrew Patterson <andrew.patterson@hp.com>
Signed-off-by: Zhang Yanmin <yanmin_zhang@linux.intel.com>
Signed-off-by: Jesse Barnes <jbarnes@virtuousgeek.org>
|
|
When the bus id part of error source id is equal to 0 or nosourceid=1,
make the kernel probe the AER status registers of all devices under the
root port to find the initial error reporter.
Reviewed-by: Andrew Patterson <andrew.patterson@hp.com>
Signed-off-by: Zhang Yanmin <yanmin_zhang@linux.intel.com>
Signed-off-by: Jesse Barnes <jbarnes@virtuousgeek.org>
|
|
Based on PCI Express AER specs, a root port might receive multiple
TLP errors while it could only save a correctable error source id
and an uncorrectable error source id at the same time. In addition,
some root port hardware might be unable to provide a correct source
id, i.e., the source id, or the bus id part of the source id provided
by root port might be equal to 0.
The patchset implements the support in kernel by searching the device
tree under the root port.
Patch 1 changes parameter cb of function pci_walk_bus to return a value.
When cb return non-zero, pci_walk_bus stops more searching on the
device tree.
Reviewed-by: Andrew Patterson <andrew.patterson@hp.com>
Signed-off-by: Zhang Yanmin <yanmin_zhang@linux.intel.com>
Signed-off-by: Jesse Barnes <jbarnes@virtuousgeek.org>
|
|
The "owner" field in struct hotplug_slot_ops is initialized by PCI
hotplug core. So each hotplug controller driver doesn't need to
initialize it.
Signed-off-by: Kenji Kaneshige <kaneshige.kenji@jp.fujitsu.com>
Reviewed-by: Alex Chiang <achiang@hp.com>
Signed-off-by: Jesse Barnes <jbarnes@virtuousgeek.org>
|
|
Create symbolic link to hotplug driver module in the PCI slot
directory (/sys/bus/pci/slots/<SLOT#>). In the past, we need to load
hotplug drivers one by one to identify the hotplug driver that handles
the slot, and it was very inconvenient especially for trouble shooting.
With this change, we can easily identify the hotplug driver.
Signed-off-by: Taku Izumi <izumi.taku@jp.fujitsu.com>
Signed-off-by: Kenji Kaneshige <kaneshige.kenji@jp.fujitsu.com>
Reviewed-by: Alex Chiang <achiang@hp.com>
Signed-off-by: Jesse Barnes <jbarnes@virtuousgeek.org>
|
|
Current has_foo() functions in pci_hotplug_core.c returns 0 if the
"foo" property is true. It would cause misunderstanding. In addition,
the error code of those functions is never checked, so this patch
changes those functions' error code to 'bool' and return true if the
property "foo" is true.
Signed-off-by: Kenji Kaneshige <kaneshige.kenji@jp.fujitsu.com>
Reviewed-by: Alex Chiang <achiang@hp.com>
Signed-off-by: Jesse Barnes <jbarnes@virtuousgeek.org>
|
|
The EMI support in pciehp is obviously broken. It is implemented using
struct hotplug_slot_attribute, but sysfs_ops for pci_slot_ktype is NOT
for struct hotplug_slot_attribute, but for struct pci_slot_attribute.
This bug had been there for a long time, maybe it was introduced when
PCI slot framework was introduced. The reason why this bug didn't
cause any problem is maybe the EMI support is not tested at all
because of lack of test environment.
As described above, the EMI support in pciehp seems not to be tested
at all. So this patch removes EMI support from pciehp, instead of
fixing the bug.
Signed-off-by: Kenji Kaneshige <kaneshige.kenji@jp.fujitsu.com>
Signed-off-by: Jesse Barnes <jbarnes@virtuousgeek.org>
|
|
Describe check_enable_amd_mmconf.
Signed-off-by: Andreas Herrmann <andreas.herrmann3@amd.com>
Signed-off-by: Jesse Barnes <jbarnes@virtuousgeek.org>
|
|
This patch adds a minimal HOWTO for PCIE AER software error injection
in Documentation/PCI/pcieaer-howto.txt.
Signed-off-by: Huang Ying <ying.huang@intel.com>
Signed-off-by: Jesse Barnes <jbarnes@virtuousgeek.org>
|
|
This is used by PCIE AER error injection to fake an PCI AER interrupt.
Signed-off-by: Huang Ying <ying.huang@intel.com>
Signed-off-by: Jesse Barnes <jbarnes@virtuousgeek.org>
|
|
pci_bus_set_ops changes pci_ops associated with a pci_bus. This can be
used by debug tools such as PCIE AER error injection to fake some PCI
configuration registers.
Acked-by: Kenji Kaneshige <kaneshige.kenji@jp.fujitsu.com>
Signed-off-by: Huang Ying <ying.huang@intel.com>
Signed-off-by: Jesse Barnes <jbarnes@virtuousgeek.org>
|
|
Use pci_is_root_bus() in pci_common_swizzle() for checking if the pci
bus is root, for code consistency.
Reviewed-by: Alex Chiang <achiang@hp.com>
Reviewed-by: Grant Grundler <grundler@parisc-linux.org>
Signed-off-by: Kenji Kaneshige <kaneshige.kenji@jp.fujitsu.com>
Signed-off-by: Jesse Barnes <jbarnes@virtuousgeek.org>
|
|
Use pci_is_root_bus() in pci_get_interrupt_pin() for checking if the
pci bus is root, for code consistency.
Reviewed-by: Alex Chiang <achiang@hp.com>
Reviewed-by: Grant Grundler <grundler@parisc-linux.org>
Signed-off-by: Kenji Kaneshige <kaneshige.kenji@jp.fujitsu.com>
Signed-off-by: Jesse Barnes <jbarnes@virtuousgeek.org>
|
|
Use pci_is_root_bus() in pci_read_bridge_bases() to check if the pci
bus is root, for code consistency.
Reviewed-by: Alex Chiang <achiang@hp.com>
Reviewed-by: Grant Grundler <grundler@parisc-linux.org>
Signed-off-by: Kenji Kaneshige <kaneshige.kenji@jp.fujitsu.com>
Signed-off-by: Jesse Barnes <jbarnes@virtuousgeek.org>
|
|
Use pci_is_root_bus() in pci_find_upstream_pcie_bridge() to check if
the pci bus is root, for code consistency.
Reviewed-by: Alex Chiang <achiang@hp.com>
Reviewed-by: Grant Grundler <grundler@parisc-linux.org>
Signed-off-by: Kenji Kaneshige <kaneshige.kenji@jp.fujitsu.com>
Signed-off-by: Jesse Barnes <jbarnes@virtuousgeek.org>
|
|
Use pci_is_root_bus() in acpi_find_root_bridge_handle() to check if
the pci bus is root, for code consistency.
Reviewed-by: Alex Chiang <achiang@hp.com>
Reviewed-by: Grant Grundler <grundler@parisc-linux.org>
Signed-off-by: Kenji Kaneshige <kaneshige.kenji@jp.fujitsu.com>
Signed-off-by: Jesse Barnes <jbarnes@virtuousgeek.org>
|
|
Use pci_is_root_bus() in acpi_pci_get_bridge_handle() to check if the
pci bus is root, for code consistency.
Reviewed-by: Grant Grundler <grundler@parisc-linux.org>
Reviewed-by: Alex Chiang <achiang@hp.com>
Signed-off-by: Kenji Kaneshige <kaneshige.kenji@jp.fujitsu.com>
Signed-off-by: Jesse Barnes <jbarnes@virtuousgeek.org>
|
|
I found no references to SMBus in ACPI DSDT disassembly on my laptop
so this should be safe.
Signed-off-by: Michal Miroslaw <mirq-linux@rere.qmqm.pl>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Jesse Barnes <jbarnes@virtuousgeek.org>
|
|
Some BIOSes hide 'overflow' device (dev #6) for i82875P/PE chipsets.
The same happens for i82865P/PE. Add a quirk to enable this device.
This allows i82875 EDAC driver to bind to chipset's dev #6 and not
dev #0 as the latter is used by AGP driver.
On my laptop (i82865P based) ACPI code is disabling this device
again in \_SB.PCI0._CRS method (called at least at PNP init time).
This can be easily worked around by patching DSDT.
[akpm@linux-foundation.org: coding-style fixes]
Signed-off-by: Michal Miroslaw <mirq-linux@rere.qmqm.pl>
Acked-by: Doug Thompson <norsk5@yahoo.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Jesse Barnes <jbarnes@virtuousgeek.org>
|
|
Addition of one unknown subsystem identifier to the quirks handler for
chipset i82855GM_HB on notebook Asus A6L. This exposes the otherwise
hidden SMBus controller within the south bridge ICH4-M.
Signed-off-by: Mats Erik Andersson <mats.andersson@gisladisker.se>
Signed-off-by: Jesse Barnes <jbarnes@virtuousgeek.org>
|
|
Adds support for PCI Express transaction layer end-to-end CRC checking
(ECRC). This patch will enable/disable ECRC checking by setting/clearing
the ECRC Check Enable and/or ECRC Generation Enable bits for devices that
support ECRC.
The ECRC setting is controlled by the "pci=ecrc=<policy>" command-line
option. If this option is not set or is set to 'bios", the enable and
generation bits are left in whatever state that firmware/BIOS set them to.
The "off" setting turns them off, and the "on" option turns them on (if the
device supports it).
Turning ECRC on or off can be a data integrity versus performance
tradeoff. In theory, turning it on will catch more data errors, turning
it off means possibly better performance since CRC does not need to be
calculated by the PCIe hardware and packet sizes are reduced.
Signed-off-by: Andrew Patterson <andrew.patterson@hp.com>
Signed-off-by: Jesse Barnes <jbarnes@virtuousgeek.org>
|
|
According to the PCI PM specification (PCI Bus Power Management
Interface Specification, Rev. 1.2, Section 5.4.1) we are supposed to
reinitialize devices that have PCI_PM_CTRL_NO_SOFT_RESET clear during
all transitions from PCI_D3hot to PCI_D0, but we only do it if the
device's current_state field is equal to PCI_UNKNOWN.
This may lead to problems if a device with PCI_PM_CTRL_NO_SOFT_RESET
unset is put into PCI_D3hot at run time by its driver and
pci_set_power_state() is used to put it back into PCI_D0, because in
that case the device will remain uninitialized after
pci_set_power_state() has returned. Prevent that from happening by
modifying pci_raw_set_power_state() to reinitialize devices with
PCI_PM_CTRL_NO_SOFT_RESET unset during all transitions from D3 to D0.
Cc: stable@kernel.org
Signed-off-by: Rafael J. Wysocki <rjw@sisk.pl>
Signed-off-by: Jesse Barnes <jbarnes@virtuousgeek.org>
|
|
PCIe root complex integrated endpoint does not implement ARI, so this
kind of endpoint uses 3-bit function number. The function dependency
link of the integrated endpoint should be calculated using the device
number plus the value from function dependency link register.
Normal endpoint always implements ARI and the function dependency link
register contains 8-bit function number (i.e. `devfn' from software's
perspective).
Signed-off-by: Yu Zhao <yu.zhao@intel.com>
Signed-off-by: Jesse Barnes <jbarnes@virtuousgeek.org>
|
|
We always call pci_stop_bus_device before calling pci_destroy_dev.
Since pci_stop_bus_device calls pci_stop_dev, there is no need
for pci_destroy_dev to repeat the call.
Signed-off-by: Alex Chiang <achiang@hp.com>
Signed-off-by: Jesse Barnes <jbarnes@virtuousgeek.org>
|
|
pci_enable_msix currently returns -EINVAL if you ask
for more vectors than supported by the device, which would
typically cause fallback to regular interrupts.
It's better to return the table size, making the driver retry
MSI-X with less vectors.
Reviewed-by: Matthew Wilcox <willy@linux.intel.com>
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: Jesse Barnes <jbarnes@virtuousgeek.org>
|
|
VIA has a strange chipset, it has root port under a bridge. Disable ASPM
for such strange chipset.
Cc: stable@kernel.org
Tested-by: Wolfgang Denk <wd@denx.de>
Signed-off-by: Shaohua Li <shaohua.li@intel.com>
Signed-off-by: Jesse Barnes <jbarnes@virtuousgeek.org>
|
|
At this point, it seems to solve more problems than it causes, so let's try using it by default. It's an easy revert if it ends up causing trouble.
Reviewed-by: Yinghai Lu <yhlu.kernel@gmail.com>
Acked-by: Bjorn Helgaas <bjorn.helgaas@hp.com>
Signed-off-by: Jesse Barnes <jbarnes@virtuousgeek.org>
|
|
The last in-tree caller of pci_find_slot has been converted, so
let's get rid of this deprecated interface.
Signed-off-by: Alex Chiang <achiang@hp.com>
Signed-off-by: Jesse Barnes <jbarnes@virtuousgeek.org>
|
|
Convert uses of pci_find_slot to modern API.
In the conversion sites, we end up calling pci_dev_put() right away.
This may seem like it misses the entire point of doing something like
pci_get_bus_and_slot(), since we drop the reference so soon, but it turns
out we don't actually do much with the returned pci_dev.
I plan on untangling cpqphp further, but clearly cpqphp never worried too
much about a properly refcounted pci_dev anyway. For now, this conversion
seems reasonable, as it gets rid of the last in-tree caller of pci_find_slot.
Signed-off-by: Alex Chiang <achiang@hp.com>
Signed-off-by: Jesse Barnes <jbarnes@virtuousgeek.org>
|
|
Eliminate this warning:
warning: return discards qualifiers from pointer target type
Signed-off-by: Alex Chiang <achiang@hp.com>
Signed-off-by: Jesse Barnes <jbarnes@virtuousgeek.org>
|
|
I have no clue what the original intent here was, but the code as
written is useless.
The old dbg() statement above the old callsite might lead one to think
that at one point, there was supposed to be some recursion, but any
sense of sanity here has been lost to the ravages of time.
Signed-off-by: Alex Chiang <achiang@hp.com>
Signed-off-by: Jesse Barnes <jbarnes@virtuousgeek.org>
|
|
Instead of making multiple calls to pcibios_get_irq_routing_table, let's
just do it once and save the answer.
The reason we were making multiple calls is because we liked to calculate
its length and perform some loop over it. Instead of open-coding the length
calculation every time, provide it in an inline helper function.
Finally, since pci_print_IRQ_route() is used only for debug, let's only
do it when cpqhp_debug is set.
Signed-off-by: Alex Chiang <achiang@hp.com>
Signed-off-by: Jesse Barnes <jbarnes@virtuousgeek.org>
|
|
Handle an empty slot at the top of the loop, and continue early.
This allows us to un-indent the rest of the function by one level.
Signed-off-by: Alex Chiang <achiang@hp.com>
Signed-off-by: Jesse Barnes <jbarnes@virtuousgeek.org>
|
|
Clean up style, whitespace in cpqphp_pci.c
Signed-off-by: Alex Chiang <achiang@hp.com>
Signed-off-by: Jesse Barnes <jbarnes@virtuousgeek.org>
|
|
Check for an empty slot, and return early if so.
This allows us to un-indent the rest of the function by one level.
Signed-off-by: Alex Chiang <achiang@hp.com>
Signed-off-by: Jesse Barnes <jbarnes@virtuousgeek.org>
|
|
Style and whitespace cleanups, no functional change.
Signed-off-by: Alex Chiang <achiang@hp.com>
Signed-off-by: Jesse Barnes <jbarnes@virtuousgeek.org>
|
