| Age | Commit message (Collapse) | Author |
|---|
|
Conflicts:
net/ipv6/route.c
This deals with a merge conflict between the net-next addition of the
inetpeer network namespace ops, and Thomas Graf's bug fix in
2a0c451ade8e1783c5d453948289e4a978d417c9 which makes sure we don't
register /proc/net/ipv6_route before it is actually safe to do so.
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/jkirsher/net-next
|
|
/proc/net/ipv6_route reflects the contents of fib_table_hash. The proc
handler is installed in ip6_route_net_init() whereas fib_table_hash is
allocated in fib6_net_init() _after_ the proc handler has been installed.
This opens up a short time frame to access fib_table_hash with its pants
down.
fib6_init() as a whole can't be moved to an earlier position as it also
registers the rtnetlink message handlers which should be registered at
the end. Therefore split it into fib6_init() which is run early and
fib6_init_late() to register the rtnetlink message handlers.
Signed-off-by: Thomas Graf <tgraf@suug.ch>
Reviewed-by: Neil Horman <nhorman@tuxdriver.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
The adapter->npars[] array has QLCNIC_MAX_PCI_FUNC elements. We
allocate it that way a few lines earlier in the function. So this test
is off by one.
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Acked-by: Anirban Chakraborty <anirban.chakraborty@qlogic.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Orphaning skb in dev_hard_start_xmit() makes bonding behavior
unfriendly for applications sending big UDP bursts : Once packets
pass the bonding device and come to real device, they might hit a full
qdisc and be dropped. Without orphaning, the sender is automatically
throttled because sk->sk_wmemalloc reaches sk->sk_sndbuf (assuming
sk_sndbuf is not too big)
We could try to defer the orphaning adding another test in
dev_hard_start_xmit(), but all this seems of little gain,
now that BQL tends to make packets more likely to be parked
in Qdisc queues instead of NIC TX ring, in cases where performance
matters.
Reverts commits :
fc6055a5ba31 net: Introduce skb_orphan_try()
87fd308cfc6b net: skb_tx_hash() fix relative to skb_orphan_try()
and removes SKBTX_DRV_NEEDS_SK_REF flag
Reported-and-bisected-by: Jean-Michel Hautbois <jhautbois@gmail.com>
Signed-off-by: Eric Dumazet <edumazet@google.com>
Tested-by: Oliver Hartkopp <socketcan@hartkopp.net>
Acked-by: Oliver Hartkopp <socketcan@hartkopp.net>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
There is a off by one error in the minimal number of BD in
bnx2x_start_xmit() and bnx2x_tx_int() before stopping/resuming tx queue.
A full size GSO packet, with data included in skb->head really needs
(MAX_SKB_FRAGS + 4) BDs, because of bnx2x_tx_split()
This error triggers if BQL is disabled and heavy TCP transmit traffic
occurs.
bnx2x_tx_split() definitely can be called, remove a wrong comment.
Reported-by: Tomas Hruby <thruby@google.com>
Signed-off-by: Eric Dumazet <edumazet@google.com>
Cc: Eilon Greenstein <eilong@broadcom.com>
Cc: Yaniv Rosner <yanivr@broadcom.com>
Cc: Merav Sicron <meravs@broadcom.com>
Cc: Tom Herbert <therbert@google.com>
Cc: Robert Evans <evansr@google.com>
Cc: Willem de Bruijn <willemb@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
(CAN_CTRLMODE_LISTENONLY & CAN_CTRLMODE_LOOPBACK) is (0x02 & 0x01) which
is zero so the condition is never true. The intent here was to test
that both flags were set.
Cc: <stable@kernel.org> # 2.6.39+
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Acked-by: Oliver Hartkopp <socketcan@hartkopp.net>
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
One tricky issue on the ipv6 side vs. ipv4 is that the ICMP callouts
to handle the error pass the 32-bit info cookie in network byte order
whereas ipv4 passes it around in host byte order.
Like the ipv4 side, we have two helper functions. One for when we
have a socket context and one for when we do not.
ip6ip6 tunnels are not handled here, because they handle PMTU events
by essentially relaying another ICMP packet-too-big message back to
the original sender.
This patch allows us to get rid of rt6_do_pmtu_disc(). It handles all
kinds of situations that simply cannot happen when we do the PMTU
update directly using a fully resolved route.
In fact, the "plen == 128" check in ip6_rt_update_pmtu() can very
likely be removed or changed into a BUG_ON() check. We should never
have a prefixed ipv6 route when we get there.
Another piece of strange history here is that TCP and DCCP, unlike in
ipv4, never invoke the update_pmtu() method from their ICMP error
handlers. This is incredibly astonishing since this is the context
where we have the most accurate context in which to make a PMTU
update, namely we have a fully connected socket and associated cached
socket route.
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
With ip_rt_frag_needed() removed, we have to explicitly update PMTU
information in every ICMP error handler.
Create two helper functions to facilitate this.
1) ipv4_sk_update_pmtu()
This updates the PMTU when we have a socket context to
work with.
2) ipv4_update_pmtu()
Raw version, used when no socket context is available. For this
interface, we essentially just pass in explicit arguments for
the flow identity information we would have extracted from the
socket.
And you'll notice that ipv4_sk_update_pmtu() is simply implemented
in terms of ipv4_update_pmtu()
Note that __ip_route_output_key() is used, rather than something like
ip_route_output_flow() or ip_route_output_key(). This is because we
absolutely do not want to end up with a route that does IPSEC
encapsulation and the like. Instead, we only want the route that
would get us to the node described by the outermost IP header.
Reported-by: Steffen Klassert <steffen.klassert@secunet.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Pull kvm fix from Marcelo Tosatti:
"Fix a spurious warning on CPU offline path"
* git://git.kernel.org/pub/scm/virt/kvm/kvm:
x86: kvmclock: remove check_and_clear_guest_paused warning
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/linusw/linux-pinctrl
Pull pinctrl fixes from Linus Walleij:
- section markup fixes
- clk_prepare() fix to conform to the clk API
- memory leaks
- incorrect debug messages
- bad errorpaths
- typos
* tag 'pinctrl-fixes-for-v3.5' of git://git.kernel.org/pub/scm/linux/kernel/git/linusw/linux-pinctrl:
pinctrl: pinctrl-mxs: set platform driver data to NULL at errpath and at unregister
pinctrl: pinctrl-mxs: Take care of frees if the kzalloc fails
pinctrl: pinctrl-imx: fix incorrect debug message of maps
pinctrl: pinctrl-imx: free if of_get_parent fails to get the parent node
pinctrl: pinctrl-imx: free allocated pinctrl_map structure only once and use kernel facilities for IMX_PMX_DUMP
pinctrl: nomadik: fix up typo
pinctrl: nomadik: add clk_prepare() call
pinctrl: fix a minor harmless typo
pinctrl: sirf: mark of_device_id match table as __devinitconst
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/tiwai/sound
Pull sound fixes from Takashi Iwai:
- Fix a regression of USB-audio PCM assignment since 3.4
- A few VGA-switcheroo-related fixes for proper HDMI audio enablement
- Fixed the missing initializations of HD-audio verbs, which may have
resulted in various breakage
- Some driver-specific ASoC updates
- A few fixes for the dynamic PCM code
- The addition of pinctrl support for the i.MX audmux which didn't make
it into -rc1 due to cross tree dependency issues
- A few minor fixes in compress API codes
* tag 'sound-3.5' of git://git.kernel.org/pub/scm/linux/kernel/git/tiwai/sound:
ALSA: hda - Don't forget to call init verbs added by fixup list
ALSA: HDA: Pin fixup for Zotac Z68 motherboard
ALSA: compress_core: cleanup pointers on stop
ALSA: compress_core: don't wake up on pause
ALSA: hda - Fix detection of Creative SoundCore3D controllers
vga_switcheroo: Enable/disable audio clients at the right time
ALSA: hda - HDMI Audio init all connectors when VGA-switcheroo is off
vga_switcheroo: Fix error without CONFIG_VGA_SWITCHEROO
ALSA: hda - Fix uninitialized HDMI controllers with VGA-switcheroo
vga_switcheroo: Add a helper function to get the client state
ALSA: usb-audio: Fix substream assignments
ASoC: tegra: add MODULE_DEVICE_TABLE to tegra30_ahub
ASoC: wm2000: Always use a 4s timeout for the firmware
ASoC: dapm: Fix input list to use source widgets
ASoC: dpcm: Fix dpcm_get_be() to check that DAI is BE
ASoC: wm8994: Apply volume updates with clocks enabled
ASoC: wm8994: Ensure all AIFnCLK events are run from the _late variants
ASoC: imx-audmux: add pinctrl support
ASoC: dapm: Fix connected widget capture path query.
|
|
Pull networking fixes from David S. Miller:
This has the fix for the wireless issues I ran into the other week as
well as:
1) Fix CAN c_can driver transmit handling resulting in BUG check
triggers, from AnilKumar Ch.
2) Fix packet drop monitor sleeping in atomic context, from Eric
Dumazet.
3) Fix mv643xx_eth driver build regression, from Andrew Lunn.
4) Inetpeer freeing needs an RCU grace period in order to avoid races
during tree invalidation. From Eric Dumazet.
5) Fix endianness bugs in xt_HMARK netfilter module, from Hans
Schillstrom.
6) Add proper module refcounting to l2tp_eth to avoid crash on module
unload, from Eric Dumazet.
7) Fix truncation of neighbour entry dumps due to logic errors in
neigh_dump_info() and friends, from Eric Dumazet.
8) The conversion of fib6_age() to dst_neigh_lookup() accidently
reversed the logic of a flags test, fix from Thomas Graf.
9) Fix checksum configuration in newer sky2 chips, from Stephen
Hemminger.
10) Revert BQL support in NIU driver, doesn't work.
11) l2tp_ip_sendmsg() illegally uses a route without a proper reference.
From Eric Dumazet.
12) be2net driver references an SKB after it's potentially been freed,
also from Eric Dumazet.
13) Fix RCU stalls in dummy net driver init. Also from Eric Dumazet.
14) lpc_eth has several bugs in it's transmit engine leading to packet
leaks and improper queue wakes, from Eric Dumazet.
15) Apply short DMA workaround to more tg3 chips, from Matt Carlson.
16) Add tilegx network driver.
17) Bonding queue mapping for a packet can get corrupted, fix from Eric
Dumazet.
18) Fix bug in netpoll_send_udp() SKB management that can leave garbage
in the payload in certain situations. From Eric Dumazet.
19) bnx2x driver interprets chip RX checksum offload incorrectly in
encapsulation situations. Fix from Eric Dumazet.
* git://git.kernel.org/pub/scm/linux/kernel/git/davem/net: (75 commits)
bnx2x: fix checksum validation
netpoll: fix netpoll_send_udp() bugs
bonding: Fix corrupted queue_mapping
bonding:record primary when modify it via sysfs
tilegx network driver: initial support
tg3: Apply short DMA frag workaround to 5906
net: stmmac: Fix clock en-/disable calls
lpc_eth: fix tx completion
lpc_eth: add missing ndo_change_mtu()
dummy: fix rcu_sched self-detected stalls
net: Reorder initialization in ip_route_output to fix gcc warning
virtio-net: fix a race on 32bit arches
r8169: avoid NAPI scheduling delay.
net: Make linux/tcp.h C++ friendly (trivial)
netdev: fix drivers/net/phy/ kernel-doc warnings
net/core: fix kernel-doc warnings
be2net: fix a race in be_xmit()
l2tp: fix a race in l2tp_ip_sendmsg()
mac80211: add back channel change flag
NFC: Fix possible NULL ptr deref when getting the name of a socket
...
|
|
This patch fixes a potential Rx timestamp deadlock that causes the Rx
timestamping to stall indefinitely. The issue could occur when a PTP packet is
timestamped by hardware but never reaches the Rx queue. In order to prevent a
permanent loss of timestamping, the RXSTMP(L/H) registers have to be read to
unlock them. (This used to only occur when a packet that was timestamped
reached the software.) However the registers can't be read early otherwise
there is no way to correlate them to the packet.
This patch introduces a filter function which can be used to determine if a
packet should have been timestamped. Supplied with the filter setup by the
hwtstamp ioctl, check to make sure the PTP protocol and message type match the
expected values. If so, then read the timestamp registers (to free them.) At
this point check the descriptor bit, if the bit is set then we know this
packet correlates to the timestamp stored in the RXTSTAMP registers.
Otherwise, assume that packet was dropped by the hardware, and ignore this
timestamp value. However, we have at least unlocked the rxtstamp registers for
future timestamping.
Due to the way the driver handles skb data, it cannot be directly accessed. In
order to work around this, a copy of the skb data into a linear buffer is
made. From this buffer it becomes possible to read the data correctly
Signed-off-by: Jacob Keller <jacob.e.keller@intel.com>
Reviewed-by: Richard Cochran <richardcochran@gmail.com>
Tested-by: Phil Schmitt <phillip.j.schmitt@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
|
|
When enabling the hwtstamp mode for Rx timestamping the V2 ptp event type
specific modes (Delay Request and Sync) have been rolled into the V2 all event
packet modes, in order to more accurately represent what hardware is doing.
Hardware always timestamps the Path delay packets when a V2 mode is selected,
regardless of what type was selected (in order to always support Path delay
mode). However this means the user selected modes of timestamping only Sync or
Delay Request is not truly supported. This patch correctly sets the mode for
the hwtstamp config and returns to the user that all V2 event packets will be
timestamped.
Signed-off-by: Jacob Keller <jacob.e.keller@intel.com>
Tested-by: Phil Schmitt <phillip.j.schmitt@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
|
|
This patch fixes two minor nits from Richard Cochran. The first is a case of
ambitious line wrapping that wasn't necessary. The second is to re-order the
flag checks for PPS support. Previously, the hardware test was done first, and
the interrupt flag test was done second. Now, test the interrupt flag and use
the unlikely macro.
Signed-off-by: Jacob Keller <jacob.e.keller@intel.com>
Tested-by: Phil Schmitt <phillip.j.schmitt@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
|
|
ixgbe_sysfs.c is only needed when CONFIG_IXGBE_HWMON is configured in the
kernel.
Signed-off-by: Emil Tantilov <emil.s.tantilov@intel.com>
Acked-by: Don Skidmore <Donald.c.skidmore@intel.com>
Tested-by: Phil Schmitt <phillip.j.schmitt@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
|
|
The flow control DV macros are used to calculate the flow control
high and low thresholds. This patch annotates these macros slightly
better and fixes the issues below.
The macro variables are renamed LINK to _max_frame_link and TC to
_max_frame_tc. This was to avoid confusion and make them more
readable. It was found that people auditing the code read TC to be
'traffic class' in the 802.1Q definition instead of the max frame
size of the tc. Hopefully it is clear now.
This audit also found the following real deviations from the
theoretical values. Fixed in this patch.
* I multiplied the DV calculations by (36/25) which always
evaluates to 1. This does not match the intended theoretical
value of 1.44.
* IXGBE_BT2KB added 1023 to account for rounding however this
really should be 8 * 1023 - 1 to account for division by 8k.
* x2 multiplication of max frame in DV calculations to account
for updated hardware recommendations.
With this patch the DV values are inline with the recommendations
in the 82599 and 82598 data sheets. Its worth noting I did not
see any dropped frames with flow control on in my experiments without
this patch. However aligning with the hardware specs and
recommendations seems like a good idea here to account for worst
case scenarios.
Signed-off-by: John Fastabend <john.r.fastabend@intel.com>
Tested-by: Ross Brattain <ross.b.brattain@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
|
|
Based on a report from Ethan Zhao, before calling register_netdev() the
driver should be using logging macros that do not display the potentially
confusing "(unregistered net_device)" yet still display the useful driver
name and PCI bus/device/function.
Reported-by: Ethan Zhao <ethan.kernel@gmail.com>
Signed-off-by: Bruce Allan <bruce.w.allan@intel.com>
Tested-by: Aaron Brown <aaron.f.brown@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
|
|
Signed-off-by: Thomas Graf <tgraf@suug.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Signed-off-by: Thomas Graf <tgraf@suug.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
When packets are dropped in TX path, its better to use kfree_skb()
instead of dev_kfree_skb() to give proper drop_monitor events.
Also move the kfree_skb() call after read_unlock() in bond_alb_xmit()
and bond_xmit_activebackup()
Signed-off-by: Eric Dumazet <edumazet@google.com>
Cc: Jay Vosburgh <fubar@us.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
bnx2x driver incorrectly sets ip_summed to CHECKSUM_UNNECESSARY on
encapsulated segments. TCP stack happily accepts frames with bad
checksums, if they are inside a GRE or IPIP encapsulation.
Our understanding is that if no IP or L4 csum validation was done by the
hardware, we should leave ip_summed as is (CHECKSUM_NONE), since
hardware doesn't provide CHECKSUM_COMPLETE support in its cqe.
Then, if IP/L4 checksumming was done by the hardware, set
CHECKSUM_UNNECESSARY if no error was flagged.
Patch based on findings and analysis from Robert Evans
Signed-off-by: Eric Dumazet <edumazet@google.com>
Cc: Eilon Greenstein <eilong@broadcom.com>
Cc: Yaniv Rosner <yanivr@broadcom.com>
Cc: Merav Sicron <meravs@broadcom.com>
Cc: Tom Herbert <therbert@google.com>
Cc: Robert Evans <evansr@google.com>
Cc: Willem de Bruijn <willemb@google.com>
Acked-by: Eilon Greenstein <eilong@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Bogdan Hamciuc diagnosed and fixed following bug in netpoll_send_udp() :
"skb->len += len;" instead of "skb_put(skb, len);"
Meaning that _if_ a network driver needs to call skb_realloc_headroom(),
only packet headers would be copied, leaving garbage in the payload.
However the skb_realloc_headroom() must be avoided as much as possible
since it requires memory and netpoll tries hard to work even if memory
is exhausted (using a pool of preallocated skbs)
It appears netpoll_send_udp() reserved 16 bytes for the ethernet header,
which happens to work for typicall drivers but not all.
Right thing is to use LL_RESERVED_SPACE(dev)
(And also add dev->needed_tailroom of tailroom)
This patch combines both fixes.
Many thanks to Bogdan for raising this issue.
Reported-by: Bogdan Hamciuc <bogdan.hamciuc@freescale.com>
Signed-off-by: Eric Dumazet <edumazet@google.com>
Tested-by: Bogdan Hamciuc <bogdan.hamciuc@freescale.com>
Cc: Herbert Xu <herbert@gondor.apana.org.au>
Cc: Neil Horman <nhorman@tuxdriver.com>
Reviewed-by: Neil Horman <nhorman@tuxdriver.com>
Reviewed-by: Cong Wang <xiyou.wangcong@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Signed-off-by: Thomas Graf <tgraf@suug.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Signed-off-by: Thomas Graf <tgraf@suug.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Signed-off-by: Thomas Graf <tgraf@suug.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
EMSGSIZE - ran out of space while constructing message
EOPNOTSUPP - driver/hardware does not support operation
ENODEV - network device not found
EINVAL - invalid message
Signed-off-by: Thomas Graf <tgraf@suug.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Signed-off-by: Thomas Graf <tgraf@suug.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Signed-off-by: Thomas Graf <tgraf@suug.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Allocating and sending the skb in dcb_doit() allows for much
shorter and cleaner command handling functions.
The huge switch statement is replaced with an array based definition
of the handling function and reply message type.
Signed-off-by: Thomas Graf <tgraf@suug.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
There is no need to allocate and send the reply message in each
handling function separately. Instead, the reply skb can be allocated
and sent in dcb_doit() directly.
Signed-off-by: Thomas Graf <tgraf@suug.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Pull SuperH fixes from Paul Mundt.
* tag 'sh-for-linus' of git://github.com/pmundt/linux-sh:
sh: Kill off additional asm-generic wrappers.
sh: Setup CROSS_COMPILE at the top
sh: Fix up link time defsym warnings.
sh: use the new generic strnlen_user() function
sh: switch to generic strncpy_from_user().
sh: Kill off last dead UBC header
serial: sh-sci: Make probe fail for ports that exceed the maximum count
serial: sh-sci: Fix probe error paths
clocksource: sh_tmu: Use clockevents_config_and_register().
clocksource: sh_tmu: Convert timer lock to raw spinlock.
clocksource: sh_mtu2: Convert timer lock to raw spinlock.
clocksource: sh_cmt: Convert timer lock to raw spinlock.
bug.h: need linux/kernel.h for TAINT_WARN.
sh: convert to kbuild asm-generic support.
sh64: Fix up fallout from generic init_task conversion.
sh: arch/sh/kernel/process.c needs asm/fpu.h for unlazy_fpu().
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/cooloney/linux-leds
Pull led fixes from Bryan Wu.
* 'fixes-for-3.5' of git://git.kernel.org/pub/scm/linux/kernel/git/cooloney/linux-leds:
leds: Make LEDS_ASIC3 and LEDS_RENESAS_TPU depend on LEDS_CLASS=y
leds: fixed a coding style issue.
leds: don't disable blinking when writing the same value to delay_on or delay_off
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/geert/linux-m68k
Pull m68k update from Geert Uytterhoeven.
This makes m68k use the generic library functions for the user-space
strn[cpy|len] functions.
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/geert/linux-m68k:
m68k: Use generic strncpy_from_user(), strlen_user(), and strnlen_user()
|
|
Pull omapdss build problem fix from Tomi Valkeinen:
"Small fixes for omapdss driver. Most importantly, fixes a build
problem when debugfs or omapdss debug support is turned off, and fixes
a suspend related crash."
This has apparently been annoying rmk for a while..
* tag 'omapdss-for-3.5-rc2' of git://gitorious.org/linux-omap-dss2/linux:
OMAPDSS: fix registration of DPI and SDI devices
OMAPDSS: DSI: Fix bug when calculating LP command interleaving parameters
OMAPDSS: fix bogus WARN_ON in dss_runtime_put()
OMAPDSS: Taal: fix compilation warning
OMAPDSS: fix build when DEBUG_FS or DSS_DEBUG_SUPPORT disabled
|
|
During the split to the auto-parser helper functions, the actual call
of init verbs was lost.
Bugzilla: https://bugzilla.kernel.org/show_bug.cgi?id=43366
Signed-off-by: Takashi Iwai <tiwai@suse.de>
|
|
Conflicts:
MAINTAINERS
drivers/net/wireless/iwlwifi/pcie/trans.c
The iwlwifi conflict was resolved by keeping the code added
in 'net' that turns off the buggy chip feature.
The MAINTAINERS conflict was merely overlapping changes, one
change updated all the wireless web site URLs and the other
changed some GIT trees to be Johannes's instead of John's.
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
and 'sh/trivial' into sh-fixes-for-linus
|
|
A few wrappers were overlooked in the initial conversion, take care of
them now.
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
|
|
CROSS_COMPILE must be setup before using e.g. cc-option (and a few other
as-*, cc-*, ld-* macros), else they will check against the wrong compiler
when cross-compiling, and may invoke the cross compiler with wrong or
suboptimal compiler options.
Signed-off-by: Geert Uytterhoeven <geert@linux-m68k.org>
Cc: Paul Mundt <lethal@linux-sh.org>
Cc: linux-sh@vger.kernel.org
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
|
|
sh-linux-gnu-ld:--defsym 'jiffies=jiffies_64': ignoring invalid character `'' in expression
For some reason ld has recently started complaining about the quotes, so just
get rid of them, we don't need them for anything anyways.
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
|
|
'Get' commands should generally not require CAP_NET_ADMIN, with
the exception of those that expose internal state.
Signed-off-by: Ben Hutchings <bhutchings@solarflare.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Add dev_loopback_xmit() in order to deduplicate functions
ip_dev_loopback_xmit() (in net/ipv4/ip_output.c) and
ip6_dev_loopback_xmit() (in net/ipv6/ip6_output.c).
I was about to reinvent the wheel when I noticed that
ip_dev_loopback_xmit() and ip6_dev_loopback_xmit() do exactly what I
need and are not IP-only functions, but they were not available to reuse
elsewhere.
ip6_dev_loopback_xmit() does not have line "skb_dst_force(skb);", but I
understand that this is harmless, and should be in dev_loopback_xmit().
Signed-off-by: Michel Machado <michel@digirati.com.br>
CC: "David S. Miller" <davem@davemloft.net>
CC: Alexey Kuznetsov <kuznet@ms2.inr.ac.ru>
CC: James Morris <jmorris@namei.org>
CC: Hideaki YOSHIFUJI <yoshfuji@linux-ipv6.org>
CC: Patrick McHardy <kaber@trash.net>
CC: Eric Dumazet <edumazet@google.com>
CC: Jiri Pirko <jpirko@redhat.com>
CC: "Michał Mirosław" <mirq-linux@rere.qmqm.pl>
CC: Ben Hutchings <bhutchings@solarflare.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Cloning all packets in input path have a significant cost.
Use skb_header_pointer()/skb_copy_bits() instead of pskb_may_pull() so
that recv_probe handlers (bond_3ad_lacpdu_recv / bond_arp_rcv /
rlb_arp_recv ) dont touch input skb.
bond_handle_frame() can avoid the skb_clone()/dev_kfree_skb()
Signed-off-by: Eric Dumazet <edumazet@google.com>
Cc: Jay Vosburgh <fubar@us.ibm.com>
Cc: Andy Gospodarek <andy@greyhouse.net>
Cc: Jiri Bohac <jbohac@suse.cz>
Cc: Nicolas de Pesloüan <nicolas.2p.debian@free.fr>
Cc: Maciej Żenczykowski <maze@google.com>
Signed-off-by: Jay Vosburgh <fubar@us.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
The line below in intr_complete isn't needed,
memset(urb->transfer_buffer, 0, urb->transfer_buffer_length);
so just remove it.
Signed-off-by: Ming Lei <tom.leiming@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Remove declaration for intr_complete so that ctags may be happy to
decrease duplicated symbols, also decrease one line code.
Signed-off-by: Ming Lei <tom.leiming@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
The flag of EVENT_DEV_WAKING is not used any more, so just remove it.
Signed-off-by: Ming Lei <tom.leiming@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
usb_device is parent device of usb_interface in the view of driver
model, so its reference count is always held during .probe/.disconnect
of usb_interface instance.
This patch just removes the unnecessay usb_get/put_dev.
Signed-off-by: Ming Lei <tom.leiming@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
usb_device is parent device of usb_interface in the view of driver
model, so its reference count is always held during .probe/.disconnect
of usb_interface instance.
This patch just removes the unnecessay usb_get/put_dev.
Signed-off-by: Ming Lei <tom.leiming@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
