summaryrefslogtreecommitdiffstats
AgeCommit message (Collapse)Author
2014-05-22mmc: sdhci: convert sdhci_set_uhs_signaling() into a library functionRussell King
Add sdhci_set_uhs_signaling() and always call the set_uhs_signaling method. This avoids quirks being added into sdhci_set_uhs_signaling(). Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk> Tested-by: Markus Pargmann <mpa@pengutronix.de> Tested-by: Stephen Warren <swarren@nvidia.com> [Ulf Hansson] Resolved conflict Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org> Signed-off-by: Chris Ball <chris@printf.net>
2014-05-22mmc: sdhci: set_uhs_signaling() need not return a valueRussell King
The set_uhs_signaling() method gives the impression that it can fail, but anything returned from the method is entirely ignored by the sdhci driver. So returning failure has no effect. So, kill the idea that it's possible for this to return an error by removing the returned value. Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk> Tested-by: Markus Pargmann <mpa@pengutronix.de> Tested-by: Stephen Warren <swarren@nvidia.com> Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org> Signed-off-by: Chris Ball <chris@printf.net>
2014-05-22mmc: sdhci-esdhc-imx: fix lockdep splat upon tuningRussell King
================================= [ INFO: inconsistent lock state ] 3.14.0-rc1+ #490 Not tainted --------------------------------- inconsistent {IN-HARDIRQ-W} -> {HARDIRQ-ON-W} usage. kworker/u8:0/6 [HC0[0]:SC0[0]:HE1:SE1] takes: (&(&host->lock)->rlock#2){?.-...}, at: [<c04b57a4>] esdhc_send_tuning_cmd+0x104/0x14c {IN-HARDIRQ-W} state was registered at: [<c00652fc>] mark_lock+0x15c/0x6f8 [<c0066354>] __lock_acquire+0xabc/0x1ca0 [<c0067ad8>] lock_acquire+0xa0/0x130 [<c0697a44>] _raw_spin_lock+0x34/0x44 [<c04b0dbc>] sdhci_irq+0x20/0xa40 [<c0071b1c>] handle_irq_event_percpu+0x74/0x284 [<c0071d70>] handle_irq_event+0x44/0x64 [<c0074db8>] handle_fasteoi_irq+0xac/0x140 [<c007147c>] generic_handle_irq+0x28/0x38 [<c000efd4>] handle_IRQ+0x40/0x98 [<c0008584>] gic_handle_irq+0x30/0x64 [<c0013144>] __irq_svc+0x44/0x58 [<c0028fc8>] irq_exit+0xc0/0x120 [<c000efd8>] handle_IRQ+0x44/0x98 [<c0008584>] gic_handle_irq+0x30/0x64 [<c0013144>] __irq_svc+0x44/0x58 [<c068f398>] printk+0x3c/0x44 [<c03191d0>] _regulator_get+0x1b4/0x1e0 [<c031924c>] regulator_get+0x18/0x1c [<c049fbc4>] mmc_add_host+0x30/0x1c0 [<c04b2e10>] sdhci_add_host+0x804/0xbbc [<c04b5318>] sdhci_esdhc_imx_probe+0x380/0x674 [<c036d530>] platform_drv_probe+0x20/0x50 [<c036b948>] driver_probe_device+0x120/0x234 [<c036baf8>] __driver_attach+0x9c/0xa0 [<c036a04c>] bus_for_each_dev+0x5c/0x90 [<c036b418>] driver_attach+0x24/0x28 [<c036b018>] bus_add_driver+0xe4/0x1d8 [<c036c1b0>] driver_register+0x80/0xfc [<c036ce28>] __platform_driver_register+0x50/0x64 [<c093706c>] sdhci_esdhc_imx_driver_init+0x18/0x20 [<c0008834>] do_one_initcall+0x3c/0x164 [<c0901c94>] kernel_init_freeable+0x104/0x1d0 [<c068c45c>] kernel_init+0x10/0x118 [<c000e768>] ret_from_fork+0x14/0x2c irq event stamp: 5933 hardirqs last enabled at (5933): [<c069813c>] _raw_spin_unlock_irqrestore+0x38/0x4c hardirqs last disabled at (5932): [<c0697b04>] _raw_spin_lock_irqsave+0x24/0x60 softirqs last enabled at (5914): [<c0028ba0>] __do_softirq+0x260/0x360 softirqs last disabled at (5909): [<c0028fc8>] irq_exit+0xc0/0x120 other info that might help us debug this: Possible unsafe locking scenario: CPU0 ---- lock(&(&host->lock)->rlock#2); <Interrupt> lock(&(&host->lock)->rlock#2); *** DEADLOCK *** 2 locks held by kworker/u8:0/6: #0: (kmmcd){.+.+.+}, at: [<c003d890>] process_one_work+0x134/0x4e8 #1: ((&(&host->detect)->work)){+.+.+.}, at: [<c003d890>] process_one_work+0x134/0x4e8 stack backtrace: CPU: 2 PID: 6 Comm: kworker/u8:0 Not tainted 3.14.0-rc1+ #490 Workqueue: kmmcd mmc_rescan Backtrace: [<c00124a0>] (dump_backtrace) from [<c0012640>] (show_stack+0x18/0x1c) [<c0012628>] (show_stack) from [<c069164c>] (dump_stack+0x70/0x8c) [<c06915dc>] (dump_stack) from [<c068f080>] (print_usage_bug+0x274/0x2e4) [<c068ee0c>] (print_usage_bug) from [<c0065774>] (mark_lock+0x5d4/0x6f8) [<c00651a0>] (mark_lock) from [<c0065e6c>] (__lock_acquire+0x5d4/0x1ca0) [<c0065898>] (__lock_acquire) from [<c0067ad8>] (lock_acquire+0xa0/0x130) [<c0067a38>] (lock_acquire) from [<c0697a44>] (_raw_spin_lock+0x34/0x44) [<c0697a10>] (_raw_spin_lock) from [<c04b57a4>] (esdhc_send_tuning_cmd+0x104/0x14c) [<c04b56a0>] (esdhc_send_tuning_cmd) from [<c04b582c>] (esdhc_executing_tuning+0x40/0x100) [<c04b57ec>] (esdhc_executing_tuning) from [<c04afa54>] (sdhci_execute_tuning+0xcc/0x754) [<c04af988>] (sdhci_execute_tuning) from [<c04a4684>] (mmc_sd_init_card+0x65c/0x694) [<c04a4028>] (mmc_sd_init_card) from [<c04a48f0>] (mmc_attach_sd+0xb0/0x184) [<c04a4840>] (mmc_attach_sd) from [<c049eb28>] (mmc_rescan+0x26c/0x2e8) [<c049e8bc>] (mmc_rescan) from [<c003d914>] (process_one_work+0x1b8/0x4e8) [<c003d75c>] (process_one_work) from [<c003e090>] (worker_thread+0x13c/0x3f8) [<c003df54>] (worker_thread) from [<c00449bc>] (kthread+0xcc/0xe8) [<c00448f0>] (kthread) from [<c000e768>] (ret_from_fork+0x14/0x2c) Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk> Tested-by: Markus Pargmann <mpa@pengutronix.de> Tested-by: Stephen Warren <swarren@nvidia.com> Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org> Signed-off-by: Chris Ball <chris@printf.net>
2014-05-22mmc: sdhci-esdhc-imx: comment runtime_pm_get_sync() in esdhc_prepare_tuning()Russell King
It is far from obvious what this is doing, and it looks like it's an unbalanced runtime_pm_get() call. However, the put is inside sdhci_tasklet_finish(), so it's not unbalanced at all. This should be documented so people know what's going on here. Do so. Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk> Tested-by: Markus Pargmann <mpa@pengutronix.de> Tested-by: Stephen Warren <swarren@nvidia.com> Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org> Signed-off-by: Chris Ball <chris@printf.net>
2014-05-22mmc: sdhci-esdhc-imx: avoid DMA to kernel stackRussell King
sdhci-esdhc-imx tries to DMA to the kernel stack when tuning the interface, which causes dma-debug to complain. Fix this by kmallocing a buffer to hold the received tuning pattern. Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk> Tested-by: Markus Pargmann <mpa@pengutronix.de> Tested-by: Stephen Warren <swarren@nvidia.com> Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org> Signed-off-by: Chris Ball <chris@printf.net>
2014-05-22mmc: sdhci: convert sdhci_set_clock() into a library functionRussell King
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk> Tested-by: Markus Pargmann <mpa@pengutronix.de> Tested-by: Stephen Warren <swarren@nvidia.com> Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org> Signed-off-by: Chris Ball <chris@printf.net>
2014-05-22mmc: sdhci: move setting mmc->actual_clock into set_clock handlersRussell King
Move the setting of mmc->actual_clock to zero into the set_clock handlers themselves. This will allow us to clean up the calling logic for the set_clock() method, and turn sdhci_set_clock() into a library function. Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk> Tested-by: Markus Pargmann <mpa@pengutronix.de> Tested-by: Stephen Warren <swarren@nvidia.com> Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org> Signed-off-by: Chris Ball <chris@printf.net>
2014-05-22mmc: sdhci: move setting host->clock into sdhci_do_set_ios()Russell King
We don't need implementations to do this, since the only time it's necessary is when we change the clock, and the only place that happens is in sdhci_do_set_ios(). So, move it there, and remove it from the iMX platform backend. Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk> Tested-by: Markus Pargmann <mpa@pengutronix.de> Tested-by: Stephen Warren <swarren@nvidia.com> Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org> Signed-off-by: Chris Ball <chris@printf.net>
2014-05-22mmc: sdhci: clean up sdhci_update_clock()/sdhci_set_clock()Russell King
Only one caller to sdhci_set_clock() needs to check whether the requested clock frequency was the same as the currently set frequency, yet we work around this in several other sites via sdhci_update_clock(). Rather than doing this, move those checks out into sdhci_do_set_ios(), which then allows sdhci_update_clock() to be eliminated. Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk> Tested-by: Markus Pargmann <mpa@pengutronix.de> Tested-by: Stephen Warren <swarren@nvidia.com> Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org> Signed-off-by: Chris Ball <chris@printf.net>
2014-05-22mmc: sdhci: convert ADMA descriptors to a coherent allocationRussell King
Rather than using the streaming API, use the coherent allocator to provide this memory, thereby eliminating cache flushing of it each time we map and unmap it. This results in a 7.5% increase in transfer speed with a UHS-1 card operating in 3.3v mode at a clock of 49.5MHz. Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk> Tested-by: Markus Pargmann <mpa@pengutronix.de> Tested-by: Stephen Warren <swarren@nvidia.com> Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org> Signed-off-by: Chris Ball <chris@printf.net>
2014-05-22mmc: sdhci: avoid sync'ing the SG if there's no misalignmentRussell King
On read, we don't need to sync the whole scatterlist and then check whether any segments need copying - if we check first, we avoid potentially expensive cache handling. Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk> Tested-by: Markus Pargmann <mpa@pengutronix.de> Tested-by: Stephen Warren <swarren@nvidia.com> Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org> Signed-off-by: Chris Ball <chris@printf.net>
2014-05-22mmc: sdhci: move FSL ESDHC reset handling quirk into esdhc codeRussell King
The Freescale esdhc driver is the only driver which needs the interrupt registers restored after a reset. Move this quirk to be part of the ESDHC driver implementation. Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk> Tested-by: Markus Pargmann <mpa@pengutronix.de> Tested-by: Stephen Warren <swarren@nvidia.com> Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org> Signed-off-by: Chris Ball <chris@printf.net>
2014-05-22mmc: sdhci: convert reset into a library functionRussell King
Rather than having platform_reset_enter/platform_reset_exit methods, turn the core of the reset handling into a library function which platforms can call at the appropriate moment in their (new) reset method. Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk> Tested-by: Markus Pargmann <mpa@pengutronix.de> Tested-by: Stephen Warren <swarren@nvidia.com> Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org> Signed-off-by: Chris Ball <chris@printf.net>
2014-05-22mmc: sdhci: convert generic bus width setup to library functionRussell King
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk> Tested-by: Markus Pargmann <mpa@pengutronix.de> Tested-by: Stephen Warren <swarren@nvidia.com> Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org> Signed-off-by: Chris Ball <chris@printf.net>
2014-05-22mmc: sdhci: plug hole in disabling card detection interruptsRussell King
When we disable card detection interrupts, we should disable both the insert and remove interrupts irrespective of the current state - this avoids races between the hardware card detect changing state before we've read that updated state and altered the interrupt mask. Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk> Tested-by: Markus Pargmann <mpa@pengutronix.de> Tested-by: Stephen Warren <swarren@nvidia.com> Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org> Signed-off-by: Chris Ball <chris@printf.net>
2014-05-22mmc: sdhci: more efficient interrupt enable register handlingRussell King
Rather than wasting cycles read-modify-writing the interrupt enable registers, cache the value locally instead. Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk> Tested-by: Markus Pargmann <mpa@pengutronix.de> Tested-by: Stephen Warren <swarren@nvidia.com> Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org> Signed-off-by: Chris Ball <chris@printf.net>
2014-05-22mmc: sdhci: allow sdio interrupts while sdhci runtime suspendedRussell King
Allow SDIO interrupts to be received while the SDHCI host is runtime suspended. We do this by leaving the AHB clock enabled while the host is runtime suspended so we can access the SDHCI registers, and so read and raise the SDIO card interrupt. Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk> Tested-by: Markus Pargmann <mpa@pengutronix.de> Tested-by: Stephen Warren <swarren@nvidia.com> Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org> Signed-off-by: Chris Ball <chris@printf.net>
2014-05-22mmc: sdhci: push card_tasklet into threaded irq handlerRussell King
There's no requirement to have the card tasklet separate now that we have a threaded interrupt handler, so kill this and move the called code into the threaded part of the handler. Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk> Tested-by: Markus Pargmann <mpa@pengutronix.de> Tested-by: Stephen Warren <swarren@nvidia.com> Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org> Signed-off-by: Chris Ball <chris@printf.net>
2014-05-22mmc: sdhci: convert to new SDIO IRQ handlingRussell King
Use a generic threaded interrupt handler for SDIO interrupt handling, rather than allowing the SDIO core code to buggily spawn its own thread. This results in host drivers to be more in control of how SDIO interrupts are acknowledged in the hardware, rather than having the internals of the SDIO core placed upon them, possibly resulting in sub-standard handling. At least one SDHCI implementation specifies a very specific sequence to deal with a card interrupt. Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk> Tested-by: Markus Pargmann <mpa@pengutronix.de> Tested-by: Stephen Warren <swarren@nvidia.com> Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org> Signed-off-by: Chris Ball <chris@printf.net>
2014-05-22mmc: sdhci: clean up sdio interrupt enable handlingRussell King
We don't need to change the SDHCI_SDIO_IRQ_ENABLED flag when we're merely receiving an interrupt - IRQ handling thread in the MMC core will either re-enable or disable the interrupt via the enable_sdio_irq callback, which will update this status appropriately. Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk> Tested-by: Markus Pargmann <mpa@pengutronix.de> Tested-by: Stephen Warren <swarren@nvidia.com> Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org> Signed-off-by: Chris Ball <chris@printf.net>
2014-05-22mmc: sdhci: clean up interrupt handlingRussell King
sdhci interrupt handling is a mess; there is a lot of code doing very similar things. Let's clean this up a bit: 1. set's clear down cmd, data and bus power interrupts in one go - we're always going to handle these. 2. use a do { } while () loop for looping while there are pending interrupts. 3. group clearing of bits in intmask into one place. This results in the code becoming simpler and easier to read. Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk> Tested-by: Markus Pargmann <mpa@pengutronix.de> Tested-by: Stephen Warren <swarren@nvidia.com> Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org> Signed-off-by: Chris Ball <chris@printf.net>
2014-05-22mmc: sdio_irq: rework sdio irq handlingRussell King
Rather than the SDIO support spawning it's own thread for handling card interrupts, use the generic IRQ infrastructure for this, triggering it from the host interface's interrupt handling directly. This avoids a race between the parent thread waiting to receive an interrupt response from the card, and the slow startup from the sdio irq thread, which can occur as a result of high system load (eg, while udev is running.) Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk> Tested-by: Markus Pargmann <mpa@pengutronix.de> Tested-by: Stephen Warren <swarren@nvidia.com> [Ulf Hansson] Resolved conflict Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org> Signed-off-by: Chris Ball <chris@printf.net>
2014-05-13mmc: sdhci: remove mdelay in eMMC tuningNick Sanders
This patch removes an unneccesary 1ms mdelay in the HS200 tuning loop, called 40 times per retuning. Currently this causes a latency of >40ms on any emmc accesses triggering wake from runtime PM, which can occur for a significant portion of reads on a mostly idle system. The delay is left in place for SD Cards, which use MMC_SEND_TUNING_BLOCK rather than MMC_SEND_TUNING_BLOCK_HS200. I'm not able to find evidence that this is required for SD in the specs I have access to, however this delay has been present from initial checkin for SD so I have preserved the original behavior for compatibility. This has been verified to fix observed glitching on local audio playback and recording on apps with inbuilt assumptions on storage latency. Signed-off-by: Nick Sanders <nsanders@chromium.org> Reviewed-by: Grant Grundler <grundler@chromium.org> Reviewed-by: Doug Anderson <dianders@chromium.org> Acked-by: Ulf Hansson <ulf.hansson@linaro.org> Signed-off-by: Chris Ball <chris@printf.net>
2014-05-12MAINTAINERS: mmc: Update email for host driver maintainerUlf Hansson
Update Ian Molton's email, the maintainer for tmio/sh_mobile_sdhci. Cc: Ian Molton <ian.molton@codethink.co.uk> Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org> Acked-by: Ian Molton <ian.molton@codethink.co.uk> Signed-off-by: Chris Ball <chris@printf.net>
2014-05-12mmc: core: Improve support for deferred regulatorsTim Kryger
Callers of mmc_regulator_get_supply could benefit from knowing if either of the regulators are present but not yet available. Since callers do not currently examine the return value, modify this function to return zero or -EPROBE_DEFER if either regulator get returns the same. Furthermore, since callers check vmmc/vqmmc using IS_ERR and can deal with absent regulators, switch to devm_regulator_get_optional. This has the added benefit of allowing this function to behave correctly even in the !CONFIG_REGULATOR case such that the stub can be removed. Signed-off-by: Tim Kryger <tim.kryger@linaro.org> Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org> Signed-off-by: Chris Ball <chris@printf.net>
2014-05-12mmc: mxcmmc: Use mmc_regulator_get_supply() APIAlexander Shiyan
This patch replaces regulator manipulation with mmc_regulator_get_supply() function from MMC core. Signed-off-by: Alexander Shiyan <shc_work@mail.ru> Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org> Signed-off-by: Chris Ball <chris@printf.net>
2014-05-12mmc: atmel: don't test host->dataAlexandre Belloni
Found using smatch: drivers/mmc/host/atmel-mci.c:827 atmci_pdc_complete() warn: variable dereferenced before check 'host->data' (see line 807) Stop testing host->data as it is not NULL at that point. Signed-off-by: Alexandre Belloni <alexandre.belloni@free-electrons.com> Acked-by: Ludovic Desroches <ludovic.desroches@atmel.com> Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org> Signed-off-by: Chris Ball <chris@printf.net>
2014-05-12mmc: rtsx: fix possible linking error if built-inArnd Bergmann
rtsx_usb_sdmmc module uses the LED classdev if available, but the code failed to consider the situation that it is built-in and the LED classdev is a module, leading to following linking error: LD init/built-in.o drivers/built-in.o: In function `rtsx_usb_sdmmc_drv_remove': rtsx_usb_sdmmc.c:(.text+0x2a018e): undefined reference to `led_classdev_unregister' drivers/built-in.o: In function `rtsx_usb_sdmmc_drv_probe': rtsx_usb_sdmmc.c:(.text+0x2a197e): undefined reference to `led_classdev_register' Fix by excluding such condition when defining macro RTSX_USB_USE_LEDS_CLASS. Signed-off-by: Roger Tseng <rogerable@realtek.com> Signed-off-by: Arnd Bergmann <arnd@arndb.de> Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org> Signed-off-by: Chris Ball <chris@printf.net>
2014-05-12mmc: mxs: fix card detection function for broken card detectDaniel Willmann
Return -ENOSYS in get_cd if broken-cd is specified in the device tree. Commit a91fe279ae75 (mmc: mxs: use standard flag for broken card detection) sets MMC_CAP_NEEDS_POLL when broken-cd is specified. This driver sets this flag unconditionally as it does not support a card detect interrupt. Instead, broken-cd means that there is no card detect signal connected. The mmc core checks the get_cd function return value to determine if a card is present. Only for a non-zero return value it will attempt to initialize the card. So retuning -ENOSYS will allow the card to be initialized. For comparison, mmc_gpio_get_cd in slot-gpio.c also returns -ENOSYS if the card detect GPIO is not valid. Signed-off-by: Daniel Willmann <daniel@totalueberwachung.de> Acked-by: Sascha Hauer <s.hauer@pengutronix.de> Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org> Signed-off-by: Chris Ball <chris@printf.net>
2014-05-12mmc: jz4740: don't wait for PRG_DONE after stop command with R1 responseAlex Smith
As of commit bcc3e1726d ("mmc: block: Use R1 responses for stop cmds for read requests"), stop commands for reads do not have MMC_RSP_BUSY set. In this case we should not wait for a PRG_DONE IRQ after sending the stop command: it will not get raised when the busy flag is not set, causing the request to fail with a timeout. Signed-off-by: Alex Smith <alex.smith@imgtec.com> Cc: Lars-Peter Clausen <lars@metafoo.de> Cc: Ulf Hansson <ulf.hansson@linaro.org> Cc: Chris Ball <chris@printf.net> Cc: James Hogan <james.hogan@imgtec.com> Acked-by: Lars-Peter Clausen <lars@metafoo.de> Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org> Signed-off-by: Chris Ball <chris@printf.net>
2014-05-12mmc: core: add DT bindings for eMMC HS400 1.8/1.2VSeungwon Jeon
Provide the option to configure these speed modes per host, for those host driver's that can't distinguish this in runtime. Specially, if host can support HS400, it means that host can also support HS200. Signed-off-by: Seungwon Jeon <tgih.jun@samsung.com> Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org> Signed-off-by: Chris Ball <chris@printf.net>
2014-05-12mmc: add support for HS400 mode of eMMC5.0Seungwon Jeon
This patch adds HS400 mode support for eMMC5.0 device. HS400 mode is high speed DDR interface timing from HS200. Clock frequency is up to 200MHz and only 8-bit bus width is supported. In addition, tuning process of HS200 is required to synchronize the command response on the CMD line because CMD input timing for HS400 mode is the same as HS200 mode. Signed-off-by: Seungwon Jeon <tgih.jun@samsung.com> Reviewed-by: Jackey Shen <jackey.shen@amd.com> Tested-by: Jaehoon Chung <jh80.chung@samsung.com> Acked-by: Jaehoon Chung <jh80.chung@samsung.com> Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org> Signed-off-by: Chris Ball <chris@printf.net>
2014-05-12mmc: rework selection of bus speed modeSeungwon Jeon
Current implementation for bus speed mode selection is too complicated. This patch is to simplify the codes and remove some duplicate parts. The following changes are including: * Adds functions for each mode selection(HS, HS-DDR, HS200 and etc) * Rearranged the mode selection sequence with supported device type * Adds maximum speed for HS200 mode(hs200_max_dtr) * Adds field definition for HS_TIMING of EXT_CSD Signed-off-by: Seungwon Jeon <tgih.jun@samsung.com> Tested-by: Jaehoon Chung <jh80.chung@samsung.com> Acked-by: Jaehoon Chung <jh80.chung@samsung.com> Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org> Signed-off-by: Chris Ball <chris@printf.net>
2014-05-12mmc: step power class after final selection of bus modeSeungwon Jeon
Power class is changed once only after selection of bus modes including speed and bus-width finishes finally. Signed-off-by: Seungwon Jeon <tgih.jun@samsung.com> Tested-by: Jaehoon Chung <jh80.chung@samsung.com> Acked-by: Jaehoon Chung <jh80.chung@samsung.com> Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org> Signed-off-by: Chris Ball <chris@printf.net>
2014-05-12mmc: identify available device type to selectSeungwon Jeon
Device types which are supported by both host and device can be identified when EXT_CSD is read. There is no need to check host's capability anymore. Signed-off-by: Seungwon Jeon <tgih.jun@samsung.com> Tested-by: Jaehoon Chung <jh80.chung@samsung.com> Acked-by: Jaehoon Chung <jh80.chung@samsung.com> Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org> Signed-off-by: Chris Ball <chris@printf.net>
2014-05-12mmc: drop the speed mode of card's stateSeungwon Jeon
Timing mode identifier has same role and can take the place of speed mode. This change removes all related speed mode. Signed-off-by: Seungwon Jeon <tgih.jun@samsung.com> Tested-by: Jaehoon Chung <jh80.chung@samsung.com> Acked-by: Jaehoon Chung <jh80.chung@samsung.com> Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org> Signed-off-by: Chris Ball <chris@printf.net>
2014-05-12mmc: mvsdio: workaround for spurious irqsSebastian Hesselbarth
SDIO controllers found on Marvell Kirkwood SoCs seem to cause a late, spurious irq although all interrupts have been disabled. This irq doesn't do any harm, neither to HW nor driver. To avoid some "unexpected irq" warning later, we workaround above issue by bailing out of irq handler early, if we didn't expect any. Signed-off-by: Sebastian Hesselbarth <sebastian.hesselbarth@gmail.com> Acked-by: Jason Cooper <jason@lakedaemon.net> Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org> Signed-off-by: Chris Ball <chris@printf.net>
2014-05-12mmc: mvsdio: silence card detect noticeSebastian Hesselbarth
mvsdio reports method of card detection with dev_notice, while for removable cards it may be sane, for non-removable cards it is not. Also, as the user cannot do anything about it, silence the message by reducing it from dev_notice to dev_dbg. Signed-off-by: Sebastian Hesselbarth <sebastian.hesselbarth@gmail.com> Acked-by: Jason Cooper <jason@lakedaemon.net> Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org> Signed-off-by: Chris Ball <chris@printf.net>
2014-05-12mmc: core: Try other signal levels during power upTim Kryger
The eMMC signalling voltage is determined by VCCQ which is provided to the card by the host. Signalling is not required to begin at 3.3v and, if the host and card both support a particular VCC/VCCQ combination, it can be used immediately. In contrast, SD Cards must begin with 3.3v signalling and may switch to a lower voltage signalling if instructed to do so in CMD11. A message is required to coordinate this operation because the card only receives a 3.3v VDD and must know when to use the 1.8v produced by its internal regulator. It makes sense for the core to begin with 3.3v signalling but when that can't be set, 1.8v and 1.2v signalling also should be attempted. This is especially important when an external regulator with a limited range is used to supply VCCQ to an eMMC part. Signed-off-by: Tim Kryger <tim.kryger@linaro.org> Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org> Signed-off-by: Chris Ball <chris@printf.net>
2014-05-12mmc: moxart: Add MOXA ART SD/MMC driverJonas Jensen
Add SD/MMC driver for MOXA ART SoCs. The "MOXA ART MMC controller" is likely a faraday "ftsdc010", a controller with support in U-Boot: http://git.denx.de/?p=u-boot.git;a=blob;f=drivers/mmc/ftsdc010_mci.c Signed-off-by: Jonas Jensen <jonas.jensen@gmail.com> Acked-by: Arnd Bergmann <arnd@arndb.de> Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org> Signed-off-by: Chris Ball <chris@printf.net>
2014-05-12mmc: Add realtek USB sdmmc host driverRoger Tseng
Realtek USB SD/MMC host driver provides mmc host support based on the Realtek USB card reader MFD driver. Signed-off-by: Roger Tseng <rogerable@realtek.com> Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org> Signed-off-by: Chris Ball <chris@printf.net>
2014-05-12mmc: sdhci-s3c: Remove unused define for NUM_GPIOSAxel Lin
NUM_GPIOS is not used after e19499ae10903 ("mmc: sdhci-s3c: let device core setup the default pin configuration"). Thus remove it. Signed-off-by: Axel Lin <axel.lin@ingics.com> Acked-by: Jaehoon Chung <jh80.chung@samsung.com> Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org> Signed-off-by: Chris Ball <chris@printf.net>
2014-05-12mmc: dw_mmc: restore the card-present checking pointJaehoon Chung
Restore the card-present checking point. (The following part was removed from commit bf626e5 ("mmc: dw_mmc: use slot-gpio to handle cd pin") Signed-off-by: Jaehoon Chung <jh80.chung@samsung.com> Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org> Signed-off-by: Chris Ball <chris@printf.net>
2014-05-12mmc: dw_mmc: remove dw_mci_of_cd_gpio/wp_gpio()Jaehoon Chung
If mmc_of_parse() is used, dw_mci_of_get_cd_gpio/wp_gpio didn't need. Already implemented into mmc_of_parse(). Signed-off-by: Jaehoon Chung <jh80.chung@samsung.com> Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org> Signed-off-by: Chris Ball <chris@printf.net>
2014-05-12mmc: dw_mmc: remove unnecessary function.Jaehoon Chung
Remove unnecessary function. This function didn't re-use anywhere. Signed-off-by: Jaehoon Chung <jh80.chung@samsung.com> Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org> Signed-off-by: Chris Ball <chris@printf.net>
2014-05-12mmc: dw_mmc: fix minor coding style.Jaehoon Chung
Fixed an indentation block. Signed-off-by: Jaehoon Chung <jh80.chung@samsung.com> Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org> Signed-off-by: Chris Ball <chris@printf.net>
2014-05-12mmc: dw_mmc: remove unused member variable.Jaehoon Chung
Since using the device-tree, didn't use the callback pointer. So removed the unused callback pointer. When the set_power callback is used, it should be added in future. Signed-off-by: Jaehoon Chung <jh80.chung@samsung.com> Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org> Signed-off-by: Chris Ball <chris@printf.net>
2014-05-12mmc: dw_mmc: replace the bus_hz checking pointJaehoon Chung
It's right to check immediately whether host->bus_hz is assigned or not. Signed-off-by: Jaehoon Chung <jh80.chung@samsung.com> Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org> Signed-off-by: Chris Ball <chris@printf.net>
2014-05-12mmc: dw_mmc: use the mmc_of_parse() instead of local parserJaehoon Chung
mmc_of_parse() have been already parsed the general capability. Didn't need to use the local parser. Signed-off-by: Jaehoon Chung <jh80.chung@samsung.com> Acked-by: Seungwon Jeon <tgih.jun@samsung.com> Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org> Signed-off-by: Chris Ball <chris@printf.net>
2014-05-12mmc: mxcmmc: Convert to SIMPLE_DEV_PM_OPSAlexander Shiyan
Signed-off-by: Alexander Shiyan <shc_work@mail.ru> Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org> Signed-off-by: Chris Ball <chris@printf.net>
generated by cgit v1.2.3-70-g09d2 (git 2.46.0) at 2024-11-24 01:54:13 +0000