summaryrefslogtreecommitdiffstats
AgeCommit message (Collapse)Author
2013-12-10ARM: shmobile: bockw: remove unused RSND_SSI_CLK_FROM_ADGKuninori Morimoto
92eba04e4bcd469518cc759ac1bf1a49acaa5cc1 (ASoC: rcar: remove RSND_SSI_CLK_FROM_ADG) removed RSND_SSI_CLK_FROM_ADG, it is no longer needed Signed-off-by: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com> Acked-by: Mark Brown <broonie@linaro.org> Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
2013-12-10ARM: shmobile: armadillo: fixup FSI address sizeKuninori Morimoto
FSI address size is 0x400, not 0x8400 Signed-off-by: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com> Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
2013-12-10ARM: Kconfig: Mention Renesas ARM SoCs instead of SH-MobileLaurent Pinchart
Only the SH-Mobile product name is mentioned in the Kconfig descriptions and help texts. This makes it difficult for external engineers working on other Renesas platforms to find upstream platform support as the combination of the SH-Mobile name and using the product number proved an effective method of concealment. Replace the "SH-Mobile" name with "Renesas ARM SoCs" in all the related descriptions, help texts and comments. Reported-by: Phil Edworthy <phil.edworthy@renesas.com> Signed-off-by: Laurent Pinchart <laurent.pinchart+renesas@ideasonboard.com> Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
2013-12-10ARM: shmobile: mackerel: Use pinconf API to configure pin pull-downLaurent Pinchart
The USB0 and USB1 VBUS pins must be pulled down. Add corresponding configuration entries in the pinctrl map table instead of manually poking the pin control registers. Signed-off-by: Laurent Pinchart <laurent.pinchart+renesas@ideasonboard.com> Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
2013-12-10ARM: shmobile: Lager:add SPI FLASH support on QSPIHiep Cao Minh
This patch enables Spansion S25FL512SAGMFIG11 chip on QSPI, Add support for the QSPI interface on Lager. Signed-off-by: Hiep Cao Minh <cm-hiep@jinso.co.jp> Acked-by: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com> Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
2013-12-10ARM: shmobile: mackerel: clk_round_rate() can return a zero to indicate an errorPaul Walmsley
Treat both negative and zero return values from clk_round_rate() as errors. This is needed since subsequent patches will convert clk_round_rate()'s return value to be an unsigned type, rather than a signed type, since some clock sources can generate rates higher than (2^31)-1 Hz. Eventually, when calling clk_round_rate(), only a return value of zero will be considered a error. All other values will be considered valid rates. The comparison against values less than 0 is kept to preserve the correct behavior in the meantime. Signed-off-by: Paul Walmsley <pwalmsley@nvidia.com> Acked-by: Laurent Pinchart <laurent.pinchart+renesas@ideasonboard.com> Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
2013-12-10ARM: shmobile: Add pinctrl_register_mappings() for KoelschMagnus Damm
Add code to setup the r8a7791 PFC for the Koelsch board. At this point serial consoles are added, and in the near future other platform-device-only devices will be added here like for instance the r8a7791 DU. Signed-off-by: Magnus Damm <damm@opensource.se> Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
2013-12-10ARM: shmobile: Use ->init_late() on LagerMagnus Damm
Hook in shmobile_init_late() on Lager V2. This enables some PM related things like CPUIdle and Suspend-to-RAM. With this patch applied it is possible to use Suspend-to-RAM: # echo enabled > /sys/class/tty/ttySC6/power/wakeup # echo mem > /sys/power/state (wake by sending a character on the serial console) Signed-off-by: Magnus Damm <damm@opensource.se> Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
2013-12-10ARM: shmobile: Hook up SW30-SW36 on KoelschMagnus Damm
Add support for Koelsch SW30-SW36 using GPIO keys. Signed-off-by: Magnus Damm <damm@opensource.se> Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
2013-12-10ARM: shmobile: koelsch: mark GPIO keys as wake-up sourcesMagnus Damm
Enable wakeup for the GPIO keys on the Koelsch board. Signed-off-by: Magnus Damm <damm@opensource.se> Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
2013-12-10ARM: shmobile: Use ->init_late() on KoelschMagnus Damm
Hook in shmobile_init_late() on Koelsch. This enables some PM related things like CPUIdle and Suspend-to-RAM. With this patch applied it is possible to use Suspend-to-RAM: # echo enabled > /sys/class/tty/ttySC6/power/wakeup # echo mem > /sys/power/state (wake by sending a character on the serial console) Signed-off-by: Magnus Damm <damm@opensource.se> Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
2013-12-10ARM: shmobile: lager: mark GPIO keys as wake-up sourcesShinya Kuribayashi
Enable wakeup for the GPIO keys on the Lager board. Signed-off-by: Shinya Kuribayashi <shinya.kuribayashi.px@renesas.com> Signed-off-by: Magnus Damm <damm@opensource.se> Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
2013-12-10ARM: shmobile: r7s72100 Genmai MultiplatformMagnus Damm
Add r7s72100 Genmai to SHMOBILE_MULTI. Signed-off-by: Magnus Damm <damm@opensource.se> Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
2013-12-10ARM: shmobile: r7s72100 Genmai DT reference C bitsMagnus Damm
Add C code support for r7s72100 Genmai DT reference. Signed-off-by: Magnus Damm <damm@opensource.se> Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
2013-12-10ARM: shmobile: r7s72100 Genmai DT reference DTS bitsMagnus Damm
Add the DT bits for r7s72100 Genmai DT reference support. Signed-off-by: Magnus Damm <damm@opensource.se> Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
2013-12-10ARM: shmobile: Initial r8a7791 and Koelsch multiplatform supportMagnus Damm
Add Koelsch and r8a7791 to CONFIG_SHMOBILE_MULTI. At this point CCF is not yet supported so you cannot run this code yet. For CCF support to happen several different components are needed, and this is one simple portion that moves us forward. Other patches need to build on top of this one. Koelsch board support exists in 3 flavors: 1) SHMOBILE_MULTI, MACH_KOELSCH - board-koelsch-reference.c (CCF + DT) 2) SHMOBILE, MACH_KOELSCH_REFERENCE - board-koelsch-reference.c (DT) 3) SHMOBILE, MACH_KOELSCH - board-koelsch.c (legacy C code) When CCF is done then 2) will be removed. When 1) includes same features as 3) then 3) will be removed. Signed-off-by: Magnus Damm <damm@opensource.se> Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
2013-12-10ARM: shmobile: koelsch: set .debounce_intervalSimon Horman
In R-Car GPIO hardware block, 'chattering removal' feature can be enabled on GPIO-n-[3:0] pins, but it's not supported on rest of pins GPIO-n-[31:4]. Set an appropriate debounce interval, instead. We could confirm that spurious/unnecessary GPIO interrupts are prevented by this settings. Based on work for the lager board by Shinya Kuribayashi. Cc: Shinya Kuribayashi <shinya.kuribayashi.px@renesas.com> Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
2013-12-10ARM: shmobile: lager: set .debounce_intervalShinya Kuribayashi
In R-Car GPIO hardware block, 'chattering removal' feature can be enabled on GPIO-n-[3:0] pins, but it's not supported on rest of pins GPIO-n-[31:4]. Set an appropriate debounce interval, instead. We could confirm that spurious/unnecessary GPIO interrupts are prevented by this settings. Signed-off-by: Shinya Kuribayashi <shinya.kuribayashi.px@renesas.com> Acked-by: Magnus Damm <damm@opensource.se> Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
2013-12-10ARM: shmobile: bockw: add pin pull-up setting for SDHIKuninori Morimoto
SDHI CD/WP pin needs pull-up Signed-off-by: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com> Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
2013-12-10ARM: shmobile: bockw: fixup FPGA ioremap areaKuninori Morimoto
Don't keep FPGA ioremap area. Signed-off-by: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com> Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
2013-12-10ARM: shmobile: r8a7791 Koelsch DT reference C bitsMagnus Damm
Add DT reference support for the r8a7791 Koelsch board. This board support file will be used together with common clocks and multiplatform in the future. Signed-off-by: Magnus Damm <damm@opensource.se> Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
2013-12-10ARM: shmobile: Add Koelsch SW2 supportMagnus Damm
Enable Koelsch GPIO switch for GPIO input and IRQ testing purpose. Signed-off-by: Magnus Damm <damm@opensource.se> Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
2013-12-10ARM: shmobile: Add Koelsch LED6, LED7 and LED8 supportMagnus Damm
Enable Koelsch LEDs for GPIO output testing purpose. Signed-off-by: Magnus Damm <damm@opensource.se> Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
2013-12-10ARM: shmobile: Enable PFC/GPIO on the Koelsch boardMagnus Damm
Enable r8a7791 PFC and GPIO on the Koelsch board. Signed-off-by: Magnus Damm <damm@opensource.se> Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
2013-12-10ARM: shmobile: bockw: use regulator for MMCIFKuninori Morimoto
When regulators are used with MMC devices, sh_mmcif_plat_data::ocr is not needed, they can be removed from platform data. This patch adds v3.3 regulator settings, and moved fixed-dummy regulator registration position Signed-off-by: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com> Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
2013-12-10Merge tag 'renesas-cleanup-for-v3.14' into boards-baseSimon Horman
Renesas ARM based SoC cleanups for v3.14 * Tidy up clock table order for r7s72100, r8a7779, r8a7779, r8a7790, sh7372 and sh73a0 SoCs. * Tidy up camera-rcar header for r8a7779 SoC * Tidy up registration of VIN on r8a7779 SoC * Tidy up PFC registration on r8a7790 SoC * Correct typo in clocks for r8a7790 SoC * Don't use named resources for IPMMU, I2C and TMU on sh73a0 SoC * Don't use named resources for MMCIF and SDHI on ape6evm board * Don't use named resources for MMCIF on lager board * Tidy up device registration on lager board * Tidy up headers for bockw board
2013-12-10ARM: shmobile: r8a7779: add HSPI clock support for DTSimon Horman
Based on work for the r8a7778 SoC by Kuninori Morimoto. Cc: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com> Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
2013-12-10ARM: shmobile: r8a7740: add FSI clock support for DTKuninori Morimoto
Signed-off-by: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com> Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
2013-12-10ARM: shmobile: r8a7790: add SSI MSTP clocksKuninori Morimoto
Signed-off-by: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com> Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
2013-12-10ARM: shmobile: r8a7778: add HPBIFx DMAEngine supportKuninori Morimoto
Signed-off-by: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com> Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
2013-12-10ARM: shmobile: Select AUTO_ZRELADDR for EMEV2Simon Horman
Since ("ARM: shmobile: Remove legacy KZM9D board code") It is now necessary for AUTO_ZRELADDR to be selected in order for the kernel to build with kzm9d_defconfig. Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
2013-12-10ARM: shmobile: r8a7790: tidyup clock table orderKuninori Morimoto
SuperH lookups clock is using CLKDEV_CON/DEV/ICK_ID() macro for a long term. But in these days, the ICK clock is defined in random place. This patch arranges it. Signed-off-by: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com> Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
2013-12-10ARM: shmobile: r8a7790: fixup I2C clock sourceKuninori Morimoto
I2C clock is based on P clock, not HP clock Signed-off-by: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com> Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
2013-12-10ARM: shmobile: r8a7790: care EXTAL divider settingsKuninori Morimoto
EXTAL clock frequency needs 1/2 when (MD14, MD13, MD19) = (1, x, x). Signed-off-by: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com> Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
2013-12-10ARM: shmobile: Add r8a7791 clocks for thermal devicesMagnus Damm
Add the r8a7791 thermal device as legacy clocks. Signed-off-by: Magnus Damm <damm@opensource.se> Acked-by: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com> Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
2013-12-10ARM: shmobile: Add r8a7791 thermal platform deviceMagnus Damm
Add a thermal platform device for the legacy case on the r8a7791 SoC. This keeps the r8a7791 in sync with the r8a7790 sister device. Signed-off-by: Magnus Damm <damm@opensource.se> Acked-by: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com> Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
2013-12-10ARM: shmobile: Add r8a7790 clocks for thermal devicesMagnus Damm
Add the r8a7790 DT thermal device to the legacy clocks. Signed-off-by: Magnus Damm <damm@opensource.se> Acked-by: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com> Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
2013-12-10ARM: Rename ARCH_SHMOBILE to ARCH_SHMOBILE_LEGACYLaurent Pinchart
SH-Mobile platforms are transitioning from non-multiplatform to multiplatform kernel. A new ARCH_SHMOBILE_MULTI configuration symbol has been created to group all multiplatform-enabled SH-Mobile SoCs. The existing ARCH_SHMOBILE configuration symbol groups SoCs that haven't been converted yet. This arrangement works fine for the arch/ code, but lots of drivers needed on both ARCH_SHMOBILE and ARCH_SHMOBILE_MULTI depend on ARCH_SHMOBILE only. In order to avoid changing them, rename ARCH_SHMOBILE to ARCH_SHMOBILE_LEGACY, and create a new boolean ARCH_SHMOBILE configuration symbol that is selected by both ARCH_SHMOBILE_LEGACY and ARCH_SHMOBILE_MULTI. Signed-off-by: Laurent Pinchart <laurent.pinchart+renesas@ideasonboard.com> Acked-by: Magnus Damm <damm@opensource.se> Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
2013-12-10ARM: shmobile: r8a7791: Add DU and LVDS clocksLaurent Pinchart
The ZX parent clock isn't implemented yet, add it as well. Signed-off-by: Laurent Pinchart <laurent.pinchart+renesas@ideasonboard.com> Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
2013-12-04ARM: shmobile: Select USE_OF on EMEV2Magnus Damm
Now when the legacy KZM9D board code is gone, make sure USE_OF is selected in case of the EMEV2 SoC. Signed-off-by: Magnus Damm <damm@opensource.se> Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
2013-12-04ARM: shmobile: r8a7778: add HSPI clock support for DTKuninori Morimoto
Signed-off-by: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com> Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
2013-12-04ARM: shmobile: Remove legacy platform devices from EMEV2 SoC codeMagnus Damm
Now when KZM9D legacy C board support code is gone then remove emev2_add_standard_devices() and all the platform devices from setup-emev2.c. Signed-off-by: Magnus Damm <damm@opensource.se> Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
2013-12-04ARM: shmobile: Remove legacy KZM9D board codeMagnus Damm
Remove the C and platform device version of KZM9D. The DT version of KZM9D board support can now instead directly be used with SoC specific code in setup-emev2.c. Signed-off-by: Magnus Damm <damm@opensource.se> Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
2013-12-04ARM: shmobile: Use ->init_late() in shared EMEV2 caseMagnus Damm
Hook up shmobile_init_late() to enable various code such as suspend-to-RAM and CPUIdle. Signed-off-by: Magnus Damm <damm@opensource.se> Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
2013-12-04ARM: shmobile: Add shared EMEV2 code for ->init_machine()Magnus Damm
Add a SoC specific function that initializes clocks and starts DT probing in case of EMEV2. This EMEV2 SoC support code may be built for either legacy SHMOBILE or SMOBILE_MULTI. The change allows us to support existing board specific KZM9D DTB with these SoC specific DT_MACHINE_START() callbacks. Signed-off-by: Magnus Damm <damm@opensource.se> Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
2013-12-04ARM: shmobile: Enable MTU2 on r7s72100Magnus Damm
Add MTU2 as r7s72100 system timer. Signed-off-by: Magnus Damm <damm@opensource.se> Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
2013-12-04ARM: shmobile: r8a7790: add QSPI supportHiep Cao Minh
Adds support for QSPI on the r8a7790. Signed-off-by: Hiep Cao Minh <cm-hiep@jinso.co.jp> Acked-by: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com> Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
2013-12-04ARM: shmobile: r8a7790: Add USBHS clock supportValentine Barshak
This adds USBHS clock support. Signed-off-by: Valentine Barshak <valentine.barshak@cogentembedded.com> Acked-by: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com> Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
2013-12-04ARM: shmobile: r8a7779: add SDHI clock support for DTKuninori Morimoto
Signed-off-by: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com> Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
2013-12-04ARM: shmobile: r8a7778: add SDHI clock support for DTKuninori Morimoto
Signed-off-by: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com> Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
generated by cgit v1.2.3-70-g09d2 (git 2.46.0) at 2025-01-10 23:32:02 +0000