summaryrefslogtreecommitdiffstats
AgeCommit message (Collapse)Author
2013-06-17ARM: dts: imx6qdl-sabresd: add clko1 iomux configurationNicolin Chen
Setting GPIO_0 pad as clko1 clock output to provide MCLK for WM8962. Signed-off-by: Nicolin Chen <b42378@freescale.com> Signed-off-by: Shawn Guo <shawn.guo@linaro.org>
2013-06-17ARM: dts: Phytec imx6q pfla02 and pbab01 supportChristian Hemp
Add support for imx6q Phytec phyFLEX-i.MX6 Quad (aka pfla02 and pbab01). - Module pfla02 - Carrier-Board pbab01 Signed-off-by: Christian Hemp <c.hemp@phytec.de> Signed-off-by: Shawn Guo <shawn.guo@linaro.org>
2013-06-17ARM: dts: imx6q: Add pinctrl for usdhc2 and enetChristian Hemp
Add a group to the usdhc2 and enet pinctrl. Signed-off-by: Christian Hemp <c.hemp@phytec.de> Signed-off-by: Shawn Guo <shawn.guo@linaro.org>
2013-06-17ARM: dts: imx27-phytec-phycore-rdk: Add MTD name for NOR flashAlexander Shiyan
This patch adds name for NOR flash. This keeps compatibility for commandline partitions parsing from old bootloaders and make name of device same for DT and non-DT boot. Signed-off-by: Alexander Shiyan <shc_work@mail.ru> Acked-by: Sascha Hauer <s.hauer@pengutonix.de> Signed-off-by: Shawn Guo <shawn.guo@linaro.org>
2013-06-17ARM: dts: imx27-phytec-phycore-rdk: Add SDHC supportAlexander Shiyan
This patch adds the SHDC devicetree node for PCM970 board. Signed-off-by: Alexander Shiyan <shc_work@mail.ru> Acked-by: Sascha Hauer <s.hauer@pengutonix.de> Signed-off-by: Shawn Guo <shawn.guo@linaro.org>
2013-06-17ARM: dts: i.MX27: Add SDHC devicetree nodesAlexander Shiyan
This patch adds the missing SDHC devicetree nodes for i.MX27 SoCs. Signed-off-by: Alexander Shiyan <shc_work@mail.ru> Acked-by: Sascha Hauer <s.hauer@pengutonix.de> Signed-off-by: Shawn Guo <shawn.guo@linaro.org>
2013-06-17ARM: dts: i.MX27: Add DMA devicetree nodeAlexander Shiyan
This patch adds the missing DMA devicetree node for i.MX27 SoCs. Signed-off-by: Alexander Shiyan <shc_work@mail.ru> Acked-by: Sascha Hauer <s.hauer@pengutonix.de> Signed-off-by: Shawn Guo <shawn.guo@linaro.org>
2013-06-17ARM: dts: imx6qdl-sabreauto: enable the WEIM NORHuang Shijie
Enable the WEIM NOR for imx6q{dl}-sabreauto boards. For the pin conflict with SPI NOR, its status is set to "disabled". Signed-off-by: Huang Shijie <b32955@freescale.com> Signed-off-by: Shawn Guo <shawn.guo@linaro.org>
2013-06-17ARM: dts: imx6dl: add pinctrls for WEIM NORHuang Shijie
Add two pinctrls for WEIM: one for the weim nor, another for the chipselect. Signed-off-by: Huang Shijie <b32955@freescale.com> Signed-off-by: Shawn Guo <shawn.guo@linaro.org>
2013-06-17ARM: dts: imx6q: add pinctrls for WEIM NORHuang Shijie
Add two pinctrls for WEIM: one for the weim nor, another for the chipselect. Signed-off-by: Huang Shijie <b32955@freescale.com> Signed-off-by: Shawn Guo <shawn.guo@linaro.org>
2013-06-17ARM: dts: imx6qdl: add more information for WEIMHuang Shijie
Add the clock and compatible information for the weim. Also adds the weim label. Signed-off-by: Huang Shijie <b32955@freescale.com> Signed-off-by: Shawn Guo <shawn.guo@linaro.org>
2013-06-17ARM: dts: imx6q{dl}: fix the pin conflict between SPI and WEIMHuang Shijie
In the imx6q-sabreauto and imx6dl-sabreauto boards, the pin MX6Q{DL}_PAD_EIM_D19 is used as a GPIO for SPI NOR, but it is used as a data pin for the WEIM NOR. In order to fix the conflict, this patch removes the pin from the hog, and adds a new board-level pinctrl: pinctrl_ecspi1_sabreauto. The SPI NOR selects this pinctrl_ecspi1_sabreauto when it is enabled. Signed-off-by: Huang Shijie <b32955@freescale.com> Signed-off-by: Shawn Guo <shawn.guo@linaro.org>
2013-06-17drivers: bus: add a new driver for WEIMHuang Shijie
The WEIM(Wireless External Interface Module) works like a bus. You can attach many different devices on it, such as NOR, onenand. In the case of i.MX6q-sabreauto, the NOR is connected to WEIM. This patch also adds the devicetree binding document. The driver only works when the devicetree is enabled. Signed-off-by: Huang Shijie <b32955@freescale.com> Acked-by: Sascha Hauer <s.hauer@pengutronix.de> Signed-off-by: Shawn Guo <shawn.guo@linaro.org>
2013-06-17ARM i.MX53: mba53: add DI1_CLK to pinctrl for disp1Markus Niebel
Add missing pin config Signed-off-by: Markus Niebel <Markus.Niebel@tqs.de> Signed-off-by: Steffen Trumtrar <s.trumtrar@pengutronix.de> Signed-off-by: Shawn Guo <shawn.guo@linaro.org>
2013-06-17ARM i.MX53: mba53: fix lvds/disp pinctrlSteffen Trumtrar
use NO_PAD_CTL / 0x80000000 instead of 0x10000 to prevent misconfigured pads Signed-off-by: Markus Niebel <Markus.Niebel@tqs.de> [Steffen: split up patch into tqma53+mba53 part] Signed-off-by: Steffen Trumtrar <s.trumtrar@pengutronix.de> Signed-off-by: Shawn Guo <shawn.guo@linaro.org>
2013-06-17ARM i.MX53: mba53: use reset gpio for FECMarkus Niebel
Signed-off-by: Markus Niebel <Markus.Niebel@tqs.de> Signed-off-by: Steffen Trumtrar <s.trumtrar@pengutronix.de> Signed-off-by: Shawn Guo <shawn.guo@linaro.org>
2013-06-17ARM i.MX53: mba53: add missing gpio stuff for pca9554Markus Niebel
Add properties to make use of pca9554 gpio expander. Signed-off-by: Markus Niebel <Markus.Niebel@tqs.de> Signed-off-by: Steffen Trumtrar <s.trumtrar@pengutronix.de> Signed-off-by: Shawn Guo <shawn.guo@linaro.org>
2013-06-17ARM i.MX53: mba53: add sound supportMarkus Niebel
Enable the sgtl5000 found on MBa53 mainboard. Also enable audio muxer and ssi, which are needed for sound to work. Signed-off-by: Markus Niebel <Markus.Niebel@tqs.de> Signed-off-by: Philipp Zabel <p.zabel@pengutronix.de> Signed-off-by: Steffen Trumtrar <s.trumtrar@pengutronix.de> Signed-off-by: Shawn Guo <shawn.guo@linaro.org>
2013-06-17ARM i.MX53: mba53: add Tevision EncoderPhilipp Zabel
Enable tve on MBa53. Signed-off-by: Philipp Zabel <p.zabel@pengutronix.de> Signed-off-by: Steffen Trumtrar <s.trumtrar@pengutronix.de> Signed-off-by: Shawn Guo <shawn.guo@linaro.org>
2013-06-17ARM i.MX53: mba53: Add display supportSascha Hauer
As the displays are optional and we have more than one, also set the status of the parallel display and the ldb to disabled. Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de> Signed-off-by: Steffen Trumtrar <s.trumtrar@pengutronix.de> Signed-off-by: Shawn Guo <shawn.guo@linaro.org>
2013-06-17ARM i.MX53: mba53: enable usbotg & usbh1Michael Olbrich
Signed-off-by: Michael Olbrich <m.olbrich@pengutronix.de> Signed-off-by: Markus Niebel <Markus.Niebel@tqs.de> Signed-off-by: Steffen Trumtrar <s.trumtrar@pengutronix.de> Signed-off-by: Shawn Guo <shawn.guo@linaro.org>
2013-06-17ARM i.MX53: tqma53: add WP/CD pinctrl and vmmc to esdhc2Steffen Trumtrar
Add WP/CD pinctrl for esdhc2. Also, add vmmc-supply for esdhc2. Signed-off-by: Steffen Trumtrar <s.trumtrar@pengutronix.de> Signed-off-by: Shawn Guo <shawn.guo@linaro.org>
2013-06-17ARM i.MX53: Add TVE entry to i.MX53 dtsiPhilipp Zabel
This adds the Television Encoder (TVEv2) device tree node to the i.MX53 dtsi. Signed-off-by: Philipp Zabel <p.zabel@pengutronix.de> Signed-off-by: Steffen Trumtrar <s.trumtrar@pengutronix.de> Signed-off-by: Shawn Guo <shawn.guo@linaro.org>
2013-06-17ARM i.MX53: tqma53: rev 300 specific pin configurationPhilipp Zabel
I2S_MCLK is moved from pad GPIO19 to GPIO0, which can be muxed to the ssi_ext1 clock signal. #SYSTEM_DOWN is moved from pad GPIO0 to GPIO19. Add #PHY_RESET and LCD_CONTRAST. Signed-off-by: Philipp Zabel <p.zabel@pengutronix.de> Signed-off-by: Steffen Trumtrar <s.trumtrar@pengutronix.de> Signed-off-by: Shawn Guo <shawn.guo@linaro.org>
2013-06-17ARM i.MX53: tqma53: fix pinctrl settingsPhilipp Zabel
BIT(31) is NO_PAD_CTL, not BIT(16) Signed-off-by: Philipp Zabel <p.zabel@pengutronix.de> Signed-off-by: Steffen Trumtrar <s.trumtrar@pengutronix.de> Signed-off-by: Shawn Guo <shawn.guo@linaro.org>
2013-06-17ARM i.MX53: tqma53: Fix interrupt polarity for the mc34708Sascha Hauer
It's active high, not active low. Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de> Signed-off-by: Shawn Guo <shawn.guo@linaro.org>
2013-06-17ARM: dts: imx27-phytec-phycore-som: Add initial support for PCM970 RDKAlexander Shiyan
Patch adds initial dts for Phytec PCM970 Rapid development kit. - Added definition for UART0 and UART1. - Added additional SPI chipselect which used on RDK for ZegBee module. Signed-off-by: Alexander Shiyan <shc_work@mail.ru> Acked-by: Sascha Hauer <s.hauer@pengutronix.de> Signed-off-by: Shawn Guo <shawn.guo@linaro.org>
2013-06-17ARM: dts: imx27-phytec-phycore-som: Remove UART definitionsAlexander Shiyan
UART1 and UART2 can be unused on some designs with PCM038 module. Remove these definitions from basic dts and lets choose user only necessary UARTs in custom designs. Keep UART0 for using this one as boot console, but since we have not way to disable usage RTSCTS signals, remove this parameter for UART0. Signed-off-by: Alexander Shiyan <shc_work@mail.ru> Acked-by: Sascha Hauer <s.hauer@pengutronix.de> Signed-off-by: Shawn Guo <shawn.guo@linaro.org>
2013-06-17ARM: dts: imx27-phytec-phycore: Rename file to match functionalityAlexander Shiyan
PCM038 dts can be used as base for development kit board or any custom PCB designs. Renames this file to match functionality. Signed-off-by: Alexander Shiyan <shc_work@mail.ru> Acked-by: Sascha Hauer <s.hauer@pengutronix.de> Signed-off-by: Shawn Guo <shawn.guo@linaro.org>
2013-06-17ARM: dts: imx27-phytec-phycore: Add reset GPIO for FECAlexander Shiyan
FEC (KSZ8001L) reset pin is connected to GPIOC30. Add this definition to dts. Signed-off-by: Alexander Shiyan <shc_work@mail.ru> Acked-by: Sascha Hauer <s.hauer@pengutronix.de> Signed-off-by: Shawn Guo <shawn.guo@linaro.org>
2013-06-17ARM: dts: add initial VF610 Tower board dts supportJingchang Lu
Add initial Freescale Vybrid VF610 Tower board support with uart and fec enabled. Signed-off-by: Jingchang Lu <b35083@freescale.com> Signed-off-by: Shawn Guo <shawn.guo@linaro.org>
2013-06-17ARM: dts: add SoC level device tree source for VF610Jingchang Lu
Add SoC level device tree source for Freescale Vybrid VF610. Signed-off-by: Jingchang Lu <b35083@freescale.com> Signed-off-by: Shawn Guo <shawn.guo@linaro.org>
2013-06-17ARM: dts: imx53: add fec pinctrlJonas Andersson
Add a group to the fec pinctrl, for use with MII interface. Signed-off-by: Jonas Andersson <jonas@microbit.se> Signed-off-by: Shawn Guo <shawn.guo@linaro.org>
2013-06-17ARM: dts: imx53: add ecspi2 pinctrlJonas Andersson
Add ecspi2 pinctrl. Signed-off-by: Jonas Andersson <jonas@microbit.se> Signed-off-by: Shawn Guo <shawn.guo@linaro.org>
2013-06-17ARM: dts: imx53: add cspi pinctrlJonas Andersson
Add a group to the cspi pinctrl. Signed-off-by: Jonas Andersson <jonas@microbit.se> Signed-off-by: Shawn Guo <shawn.guo@linaro.org>
2013-06-17ARM: dts: mx53qsb: Add support for parallel displayRogerio Pimentel
Add support for CLAA WVGA display for i.MX53 QSB. Signed-off-by: Rogerio Pimentel <rogerio.pimentel@freescale.com> Acked-by: Sascha Hauer <s.hauer@pengutronix.de> Signed-off-by: Shawn Guo <shawn.guo@linaro.org>
2013-06-17ARM: imx: apf51: add nfc supportGwenhael Goavec-Merou
Signed-off-by: Gwenhael Goavec-Merou <gwenhael.goavec-merou@armadeus.com> Signed-off-by: Shawn Guo <shawn.guo@linaro.org>
2013-06-17i.MX6: Documentation: update from fsl,card-wired to non-removableDirk Behme
With the commit 7f217794f (mmc: dt: Consolidate DT bindings), the device tree properties used by various device drivers for SD/MMC host controllers were standardized. One of the changes was that the property "fsl,card-wired", previously used by the Freescale driver, was replaced with "non-removable". Fix the example documentation regarding this. Signed-off-by: Dirk Behme <dirk.behme@de.bosch.com> Signed-off-by: Shawn Guo <shawn.guo@linaro.org>
2013-06-17ARM: dts: imx6qdl: remove redundant ocotp nodeShawn Guo
There is a redundant ocotp node. Remove it. Signed-off-by: Shawn Guo <shawn.guo@linaro.org>
2013-06-17ARM: dts: imx6qdl: remove redundant usbmisc labelShawn Guo
There is a redundant label on usbmisc node. Remove it. Signed-off-by: Shawn Guo <shawn.guo@linaro.org>
2013-06-17ARM: dts: imx6sl: add initial imx6sl-evk supportShawn Guo
Add initial imx6sl-evk board support with uart, usdhc and fec enabled. Signed-off-by: Shawn Guo <shawn.guo@linaro.org>
2013-06-17ARM: dts: add device tree source for imx6sl SoCShawn Guo
Add SoC level device tree source for imx6sl. Signed-off-by: Shawn Guo <shawn.guo@linaro.org>
2013-06-17ARM: dts: i.MX6: configure L2 cache data and tag latencyDirk Behme
Configure the data and tag latency for the L2 cache. This improves the system performance. This configuration is taken from Freescale's kernel patch "ENGR00153601 [MX6]Adjust L2 cache parameter" [1] which does writel(0x132, IO_ADDRESS(L2_BASE_ADDR + L2X0_TAG_LATENCY_CTRL)); writel(0x132, IO_ADDRESS(L2_BASE_ADDR + L2X0_DATA_LATENCY_CTRL)); In this patch we are doing the same via the device tree. Signed-off-by: Dirk Behme <dirk.behme@de.bosch.com> Signed-off-by: Shawn Guo <shawn.guo@linaro.org> [1] http://git.freescale.com/git/cgit.cgi/imx/linux-2.6-imx.git/commit/arch/arm/mach-mx6/mm.c?h=imx_3.0.35_12.09.01&id=814656410b40c67a10b25300e51b0477b2bb96d1
2013-06-17ARM: dts: add SPI/NOR for mx6q{dl}-sabreauto boardsHuang Shijie
Since the SPI/NOR has pin conflict with the WEIM NOR, we disable the spi/nor by default. Signed-off-by: Huang Shijie <b32955@freescale.com> Signed-off-by: Shawn Guo <shawn.guo@linaro.org>
2013-06-17ARM: dts: imx6q: add a gpio for hogHuang Shijie
The SPI/NOR needs this gpio for CS. So add this gpio in the hog pinctrl. Signed-off-by: Huang Shijie <b32955@freescale.com> Signed-off-by: Shawn Guo <shawn.guo@linaro.org>
2013-06-17ARM: dts: imx6dl: add a gpio for hogHuang Shijie
The SPI/NOR needs this gpio for CS. So add this gpio in the hog pinctrl. Signed-off-by: Huang Shijie <b32955@freescale.com> Signed-off-by: Shawn Guo <shawn.guo@linaro.org>
2013-06-17ARM: dts: imx6dl: add a pinctrl for eCSPI1Huang Shijie
Signed-off-by: Huang Shijie <b32955@freescale.com> Signed-off-by: Shawn Guo <shawn.guo@linaro.org>
2013-06-17ARM: dts: enable the gpmi-nand for imx6q{dl}-sabreauto boardsHuang Shijie
enable the gpmi-nand for imx6q-sabreauto and imx6qdl-sabreauto boards. Signed-off-by: Huang Shijie <b32955@freescale.com> Signed-off-by: Shawn Guo <shawn.guo@linaro.org>
2013-06-17ARM: dts: imx6dl: add pinctrl for gpmi-nandHuang Shijie
add the pinctrl item for gpmi-nand. Signed-off-by: Huang Shijie <b32955@freescale.com> Signed-off-by: Shawn Guo <shawn.guo@linaro.org>
2013-06-17ARM: dts: imx6q: remove the unused pins for gpmi-nandHuang Shijie
The gpmi does not use the MX6Q_PAD_NANDF_CS2__NAND_CE2_B and MX6Q_PAD_NANDF_CS3__NAND_CE3_B. Just remove them. Signed-off-by: Huang Shijie <b32955@freescale.com> Signed-off-by: Shawn Guo <shawn.guo@linaro.org>
generated by cgit v1.2.3-70-g09d2 (git 2.46.0) at 2024-10-24 02:19:22 +0000