| Age | Commit message (Collapse) | Author |
|---|
|
The uart timer will schedule a tasklet when it fires. It is possible that it
can fire inside _shutdown before it is killed in the dma and pdc cleanup
routines. This causes a tasklet that exists after the port is shutdown, so when
the kernel finally executes it, it panics as the tty port is NULL.
This is a somewhat rare condition but its possible if a program keeps on
opening/closing the port. It has been observed in particular with systemd
boot messages that were causing a kernel panic because of this behavior.
Moving the timer deletion to the beginning of the function stops a tasklet from
being scheduled unexpectedly.
Signed-off-by: Marek Roszko <mark.roszko@gmail.com>
Cc: stable <stable@vger.kernel.org> # v3.12
[nicolas.ferre@atmel.com: modify commit message, call setup_timer() in any case]
Signed-off-by: Nicolas Ferre <nicolas.ferre@atmel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
Tegra chips have 4 or 5 identical UART modules embedded. UARTs C..E have
their MODEM-control signals tied off to a static state. However UARTs A
and B can optionally route those signals to/from package pins, depending
on the exact pinmux configuration.
When these signals are not routed to package pins, false interrupts may
trigger either temporarily, or permanently, all while not showing up in
the IIR; it will read as NO_INT. This will eventually lead to the UART
IRQ being disabled due to unhandled interrupts. When this happens, the
kernel may print e.g.:
irq 68: nobody cared (try booting with the "irqpoll" option)
In order to prevent this, enable UART_BUG_NOMSR. This prevents
UART_IER_MSI from being enabled, which prevents the false interrupts
from triggering.
In practice, this is not needed under any of the following conditions:
* On Tegra chips after Tegra30, since the HW bug has apparently been
fixed.
* On UARTs C..E since their MODEM control signals are tied to the correct
static state which doesn't trigger the issue.
* On UARTs A..B if the MODEM control signals are routed out to package
pins, since they will then carry valid signals.
However, we ignore these exceptions for now, since they are only relevant
if a board actually hooks up more than a 4-wire UART, and no currently
supported board does this. If we ever support a board that does, we can
refine the algorithm that enables UART_BUG_NOMSR to take those exceptions
into account, and/or read a flag from DT/... that indicates that the
board has hooked up and pinmux'd more than a 4-wire UART.
Reported-by: Olof Johansson <olof@lixom.net> # autotester
Cc: <stable@vger.kernel.org>
Signed-off-by: Stephen Warren <swarren@nvidia.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
When using RX DMA, the driver won't pass any data to the uart layer
until the buffer is flipped. When the port is shutdown, the dma buffers
are unmapped, but the head and tail of the ring buffer are not reseted.
Since the serial console will keep the port open, this will only
present itself when the uart is not shared.
To reproduce the issue, with an unpatched driver, run a getty on /dev/ttyS0
with no serial console and exit. Getty will exit, and when the new one returns
you will be unable to log in. If you hold down a key long enough to fill the
DMA buffer and flip it, you can then log in.
Signed-off-by: Mark Deneen <mdeneen@gmail.com>
Acked-by: Leilei Zhao <leilei.zhao@atmel.com>
[nicolas.ferre@atmel.com: adapt to mainline kernel, handle !DMA case]
Cc: <stable@vger.kernel.org> # v3.12
Signed-off-by: Nicolas Ferre <nicolas.ferre@atmel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
The _remove callback could be called when a tasklet is scheduled. tasklet_kill
was called inside the function in order to free up any scheduled tasklets.
However it was called after uart_remove_one_port which destroys tty references
needed in the port for atmel_tasklet_func.
Simply putting the tasklet_kill at the start of the function will prevent this
conflict.
Signed-off-by: Marek Roszko <mark.roszko@gmail.com>
Acked-by: Leilei Zhao <leilei.zhao@atmel.com>
Cc: <stable@vger.kernel.org> # v3.12
Signed-off-by: Nicolas Ferre <nicolas.ferre@atmel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
Interrupts were being cleaned up late in the shutdown handler, it is possible
that an interrupt can occur and schedule a tasklet that runs after the port is
cleaned up. There is a null dereference due to this race condition with the
following stacktrace:
[<c02092b0>] (atmel_tasklet_func+0x514/0x814) from [<c001fd34>] (tasklet_action+0x70/0xa8)
[<c001fd34>] (tasklet_action+0x70/0xa8) from [<c001f60c>] (__do_softirq+0x90/0x144)
[<c001f60c>] (__do_softirq+0x90/0x144) from [<c001fa18>] (irq_exit+0x40/0x4c)
[<c001fa18>] (irq_exit+0x40/0x4c) from [<c000e298>] (handle_IRQ+0x64/0x84)
[<c000e298>] (handle_IRQ+0x64/0x84) from [<c000d6c0>] (__irq_svc+0x40/0x50)
[<c000d6c0>] (__irq_svc+0x40/0x50) from [<c0208060>] (atmel_rx_dma_release+0x88/0xb8)
[<c0208060>] (atmel_rx_dma_release+0x88/0xb8) from [<c0209740>] (atmel_shutdown+0x104/0x160)
[<c0209740>] (atmel_shutdown+0x104/0x160) from [<c0205e8c>] (uart_port_shutdown+0x2c/0x38)
Signed-off-by: Marek Roszko <mark.roszko@gmail.com>
Acked-by: Leilei Zhao <leilei.zhao@atmel.com>
Cc: <stable@vger.kernel.org> # v3.12
Signed-off-by: Nicolas Ferre <nicolas.ferre@atmel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
In rx dma-callback it calls tasklet_schedule, if the tasklet
be scheduled after all the dma-callback in the rx dma channel,
current check condition in the tasklet will not do fetch dma
buffer into tty because tx_issued is equal with tx_completed,
so as timeout tasklet does.
so we check whether we should fetch the whole dma buffer into
tty according to the status of transactions in rx dma channel.
Signed-off-by: Qipan Li <Qipan.Li@csr.com>
Signed-off-by: Barry Song <Baohua.Song@csr.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
this patch provides PM entry of uart_ops, then drop clk enable and
disable because serial core will do it.
the patch also fixes the issue that uart hang in resume caused by
not-enabled clock.
Signed-off-by: Qipan Li <Qipan.Li@csr.com>
Signed-off-by: Barry Song <Baohua.Song@csr.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
use SET_SYSTEM_SLEEP_PM_OPS to initialize suspend/resume functions
instead of legacy suspend and resume entries of platform_driver.
this will add hibernation support automatically as suspend to disk
entries are also set.
Signed-off-by: Qipan Li <Qipan.Li@csr.com>
Signed-off-by: Barry Song <Baohua.Song@csr.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
This helps increasing build testing coverage.
To do this, read{write}_relaxed() functions was be replaced with
simple read{write}() variants. Potential "uninitialized variable"
warnings was be fixed if driver compiled without MFD_SYSCON.
Signed-off-by: Alexander Shiyan <shc_work@mail.ru>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
This patch replace custom handling of IrDA feature with N_IRDA
line discipline, so IrDA mode can be used with irtty driver.
Signed-off-by: Alexander Shiyan <shc_work@mail.ru>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
The four variants of the synclink driver use the same code in their
open() callback to wait for a port in process of being closed,
using interruptible_sleep_on, which is racy and going away soon.
Making things worse, these functions hold the BTM while doing so,
which means that if we ever enter this code path, we cannot actually
continue since the other thread that is in process of closing the
port can no longer get the BTM.
This addresses both issues by using wait_event_interruptible_tty()
instead.
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Cc: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Cc: Jiri Slaby <jslaby@suse.cz>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
interruptible_sleep_on is generally problematic and we want to get
rid of it. In case of TIOCMIWAIT, that race is actually in user
space and does not get fixed since we can only detect changes after
entering the ioctl handler, but it removes one more caller.
This instance can not be trivially replaced with wait_event, so
I chose to open-code the wait loop using prepare_to_wait/finish_wait.
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Cc: Geert Uytterhoeven <geert@linux-m68k.org>
Cc: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
None of these files are actually using any __init type directives
and hence don't need to include <linux/init.h>. Most are just a
left over from __devinit and __cpuinit removal, or simply due to
code getting copied from one driver to the next.
Signed-off-by: Paul Gortmaker <paul.gortmaker@windriver.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
We need the tty fixes in here as well.
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc
Pull ARM SoC fixes from Olof Johansson:
"Much smaller batch of fixes this week.
Biggest one is a revert of an OMAP display change that removed some
non-DT pinmux code that was still needed for 3.13 to get DSI displays
to work.
There's also a fix that resolves some misdescribed GPIO controller
resources on shmobile. The rest are mostly smaller fixes, a couple of
MAINTAINERS updates, etc"
* tag 'fixes-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc:
Revert "ARM: OMAP2+: Remove legacy mux code for display.c"
MAINTAINERS: Add keystone clock drivers
MAINTAINERS: Add keystone git tree information
ARM: s3c64xx: dt: Fix boot failure due to double clock initialization
ARM: shmobile: r8a7790: Fix GPIO resources in DTS
irqchip: renesas-intc-irqpin: Fix register bitfield shift calculation
ARM: shmobile: lager: phy fixup needs CONFIG_PHYLIB
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/ieee1394/linux1394
Pull firewire fixlet from Stefan Richter:
"A one-liner to reenable WRITE SAME over SBP-2 like in v3.8...v3.12.
Buggy targets which could malfunction when being subjected to this
command are already sufficiently protected by a scsi_level check in sd
+ SCSI core"
* tag 'firewire-fix' of git://git.kernel.org/pub/scm/linux/kernel/git/ieee1394/linux1394:
firewire: sbp2: bring back WRITE SAME support
|
|
Pull SCSI target fixes from Nicholas Bellinger:
"Mostly minor items this time around, the most notable being a FILEIO
backend change to enforce hw_max_sectors based upon the current
block_size to address a bug where large sized I/Os (> 1M) where being
rejected"
* git://git.kernel.org/pub/scm/linux/kernel/git/nab/target-pending:
qla2xxx: Fix scsi_host leak on qlt_lport_register callback failure
target: Remove extra percpu_ref_init
target/file: Update hw_max_sectors based on current block_size
iser-target: Move INIT_WORK setup into isert_create_device_ib_res
iscsi-target: Fix incorrect np->np_thread NULL assignment
qla2xxx: Fix schedule_delayed_work() for target timeout calculations
iser-target: fix error return code in isert_create_device_ib_res()
iscsi-target: Fix-up all zero data-length CDBs with R/W_BIT set
target: Remove write-only stats fields and lock from struct se_node_acl
iscsi-target: return -EINVAL on oversized configfs parameter
|
|
Pull AIO leak fixes from Ben LaHaise:
"I've put these two patches plus Linus's change through a round of
tests, and it passes millions of iterations of the aio numa
migratepage test, as well as a number of repetitions of a few simple
read and write tests.
The first patch fixes the memory leak Kent introduced, while the
second patch makes aio_migratepage() much more paranoid and robust"
* git://git.kvack.org/~bcrl/aio-next:
aio/migratepages: make aio migrate pages sane
aio: fix kioctx leak introduced by "aio: Fix a trinity splat"
|
|
Since commit 36bc08cc01709 ("fs/aio: Add support to aio ring pages
migration") the aio ring setup code has used a special per-ring backing
inode for the page allocations, rather than just using random anonymous
pages.
However, rather than remembering the pages as it allocated them, it
would allocate the pages, insert them into the file mapping (dirty, so
that they couldn't be free'd), and then forget about them. And then to
look them up again, it would mmap the mapping, and then use
"get_user_pages()" to get back an array of the pages we just created.
Now, not only is that incredibly inefficient, it also leaked all the
pages if the mmap failed (which could happen due to excessive number of
mappings, for example).
So clean it all up, making it much more straightforward. Also remove
some left-overs of the previous (broken) mm_populate() usage that was
removed in commit d6c355c7dabc ("aio: fix race in ring buffer page
lookup introduced by page migration support") but left the pointless and
now misleading MAP_POPULATE flag around.
Tested-and-acked-by: Benjamin LaHaise <bcrl@kvack.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
|
|
The arbitrary restriction on page counts offered by the core
migrate_page_move_mapping() code results in rather suspicious looking
fiddling with page reference counts in the aio_migratepage() operation.
To fix this, make migrate_page_move_mapping() take an extra_count parameter
that allows aio to tell the code about its own reference count on the page
being migrated.
While cleaning up aio_migratepage(), make it validate that the old page
being passed in is actually what aio_migratepage() expects to prevent
misbehaviour in the case of races.
Signed-off-by: Benjamin LaHaise <bcrl@kvack.org>
|
|
e34ecee2ae791df674dfb466ce40692ca6218e43 reworked the percpu reference
counting to correct a bug trinity found. Unfortunately, the change lead
to kioctxes being leaked because there was no final reference count to
put. Add that reference count back in to fix things.
Signed-off-by: Benjamin LaHaise <bcrl@kvack.org>
Cc: stable@vger.kernel.org
|
|
Commit 1bf49dd4be0b ("./Makefile: export initial ramdisk compression
config option") started setting the INITRD_COMPRESS environment variable
depending on which decompression models the kernel had available.
That is completely broken.
For example, we by default have CONFIG_RD_LZ4 enabled, and are able to
decompress such an initrd, but the user tools to *create* such an initrd
may not be availble. So trying to tell dracut to generate an
lz4-compressed image just because we can decode such an image is
completely inappropriate.
Cc: J P <ppandit@redhat.com>
Cc: Andrew Morton <akpm@linux-foundation.org>
Cc: Jan Beulich <JBeulich@suse.com>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
|
|
Pull xfs bugfixes from Ben Myers:
"This contains fixes for some asserts
related to project quotas, a memory leak, a hang when disabling group or
project quotas before disabling user quotas, Dave's email address, several
fixes for the alignment of file allocation to stripe unit/width geometry, a
fix for an assertion with xfs_zero_remaining_bytes, and the behavior of
metadata writeback in the face of IO errors.
Details:
- fix memory leak in xfs_dir2_node_removename
- fix quota assertion in xfs_setattr_size
- fix quota assertions in xfs_qm_vop_create_dqattach
- fix for hang when disabling group and project quotas before
disabling user quotas
- fix Dave Chinner's email address in MAINTAINERS
- fix for file allocation alignment
- fix for assertion in xfs_buf_stale by removing xfsbdstrat
- fix for alignment with swalloc mount option
- fix for "retry forever" semantics on IO errors"
* tag 'xfs-for-linus-v3.13-rc5' of git://oss.sgi.com/xfs/xfs:
xfs: abort metadata writeback on permanent errors
xfs: swalloc doesn't align allocations properly
xfs: remove xfsbdstrat error
xfs: align initial file allocations correctly
MAINTAINERS: fix incorrect mail address of XFS maintainer
xfs: fix infinite loop by detaching the group/project hints from user dquot
xfs: fix assertion failure at xfs_setattr_nonsize
xfs: fix false assertion at xfs_qm_vop_create_dqattach
xfs: fix memory leak in xfs_dir2_node_removename
|
|
Commit 597d795a2a78 ('mm: do not allocate page->ptl dynamically, if
spinlock_t fits to long') restructures some allocators that are compiled
even if USE_SPLIT_PTLOCKS arn't used. It results in compilation
failure:
mm/memory.c:4282:6: error: 'struct page' has no member named 'ptl'
mm/memory.c:4288:12: error: 'struct page' has no member named 'ptl'
Add in the missing ifdef.
Fixes: 597d795a2a78 ('mm: do not allocate page->ptl dynamically, if spinlock_t fits to long')
Signed-off-by: Olof Johansson <olof@lixom.net>
Cc: Kirill A. Shutemov <kirill.shutemov@linux.intel.com>
Cc: Hugh Dickins <hughd@google.com>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/vgupta/arc
Pull ARC fix from Vineet Gupta:
"Fix busted syscall table due to unistd header inclusion issue"
* tag 'arc-fixes-for-3.13-rc5' of git://git.kernel.org/pub/scm/linux/kernel/git/vgupta/arc:
ARC: Allow conditional multiple inclusion of uapi/asm/unistd.h
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/arm64/linux
Pull arm64 ptrace fix from Catalin Marinas.
* tag 'arm64-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/arm64/linux:
arm64: ptrace: avoid using HW_BREAKPOINT_EMPTY for disabled events
|
|
Some pstore backing devices use on board flash as persistent
storage. These have limited numbers of write cycles so it
is a poor idea to use them from high frequency operations.
Signed-off-by: Tony Luck <tony.luck@intel.com>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/djbw/dmaengine
Pull dmaengine fixes from Dan Williams:
- deprecation of net_dma to be removed in 3.14
- crash regression fix in pl330 from the dmaengine_unmap rework
- crash regression fix for any channel running raid ops without
CONFIG_ASYNC_TX_DMA from dmaengine_unmap
- memory leak regression in mv_xor from dmaengine_unmap
- build warning regressions in mv_xor, fsldma, ppc4xx, txx9, and
at_hdmac from dmaengine_unmap
- sleep in atomic regression in dma_async_memcpy_pg_to_pg
- new fix in mv_xor for handling channel initialization failures
* tag 'dmaengine-fixes-3.13-rc4' of git://git.kernel.org/pub/scm/linux/kernel/git/djbw/dmaengine:
net_dma: mark broken
dma: pl330: ensure DMA descriptors are zero-initialised
dmaengine: fix sleep in atomic
dmaengine: mv_xor: fix oops when channels fail to initialise
dma: mv_xor: Use dmaengine_unmap_data for the self-tests
dmaengine: fix enable for high order unmap pools
dma: fix build warnings in txx9
dmatest: fix build warning on mips
dma: fix fsldma build warnings
dma: fix build warnings in ppc4xx
dmaengine: at_hdmac: remove unused function
dma: mv_xor: remove mv_desc_get_dest_addr()
|
|
Pull KVM fixes from Paolo Bonzini:
"The PPC folks had a large amount of changes queued for 3.13, and now
they are fixing the bugs"
* tag 'for-linus' of git://git.kernel.org/pub/scm/virt/kvm/kvm:
KVM: PPC: Book3S HV: Don't drop low-order page address bits
powerpc: book3s: kvm: Don't abuse host r2 in exit path
powerpc/kvm/booke: Fix build break due to stack frame size warning
KVM: PPC: Book3S: PR: Enable interrupts earlier
KVM: PPC: Book3S: PR: Make svcpu -> vcpu store preempt savvy
KVM: PPC: Book3S: PR: Export kvmppc_copy_to|from_svcpu
KVM: PPC: Book3S: PR: Don't clobber our exit handler id
powerpc: kvm: fix rare but potential deadlock scene
KVM: PPC: Book3S HV: Take SRCU read lock around kvm_read_guest() call
KVM: PPC: Book3S HV: Make tbacct_lock irq-safe
KVM: PPC: Book3S HV: Refine barriers in guest entry/exit
KVM: PPC: Book3S HV: Fix physical address calculations
|
|
In struct page we have enough space to fit long-size page->ptl there,
but we use dynamically-allocated page->ptl if size(spinlock_t) is larger
than sizeof(int).
It hurts 64-bit architectures with CONFIG_GENERIC_LOCKBREAK, where
sizeof(spinlock_t) == 8, but it easily fits into struct page.
Signed-off-by: Kirill A. Shutemov <kirill.shutemov@linux.intel.com>
Acked-by: Hugh Dickins <hughd@google.com>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
|
|
there is an overflow in the code :
cyz_polling_cycle = (arg * HZ) / 1000,
the multiplicator arg comes from user, so it may be an overflow if
arg is a big number. And the value of cyc_polling_cycle will be
wrong when it is used next time.
Reported-by: Qixue Xiao <xiaoqixue_1@163.com>
Suggested-by: Yongjian Xu <xuyongjiande@gmail.com>
Suggested-by: Yu Chen <chyyuu@gmail.com>
Signed-off-by: Qixue Xiao <xiaoqixue_1@163.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
Commit 81c0a2bb515f ("mm: page_alloc: fair zone allocator policy") meant
to bring aging fairness among zones in system, but it was overzealous
and badly regressed basic workloads on NUMA systems.
Due to the way kswapd and page allocator interacts, we still want to
make sure that all zones in any given node are used equally for all
allocations to maximize memory utilization and prevent thrashing on the
highest zone in the node.
While the same principle applies to NUMA nodes - memory utilization is
obviously improved by spreading allocations throughout all nodes -
remote references can be costly and so many workloads prefer locality
over memory utilization. The original change assumed that
zone_reclaim_mode would be a good enough predictor for that, but it
turned out to be as indicative as a coin flip.
Revert the NUMA aspect of the fairness until we can find a proper way to
make it configurable and agree on a sane default.
Signed-off-by: Johannes Weiner <hannes@cmpxchg.org>
Reviewed-by: Michal Hocko <mhocko@suse.cz>
Signed-off-by: Mel Gorman <mgorman@suse.de>
Cc: <stable@kernel.org> # 3.12
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
|
|
policy"
This reverts commit 73f038b863df. The NUMA behaviour of this patch is
less than ideal. An alternative approch is to interleave allocations
only within local zones which is implemented in the next patch.
Cc: stable@vger.kernel.org
Signed-off-by: Mel Gorman <mgorman@suse.de>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
|
|
Sasha Levin found a NULL pointer dereference that is due to a missing
page table lock, which in turn is due to the pmd entry in question being
a transparent huge-table entry.
The code - introduced in commit 1998cc048901 ("mm: make
madvise(MADV_WILLNEED) support swap file prefetch") - correctly checks
for this situation using pmd_none_or_trans_huge_or_clear_bad(), but it
turns out that that function doesn't work correctly.
pmd_none_or_trans_huge_or_clear_bad() expected that pmd_bad() would
trigger if the transparent hugepage bit was set, but it doesn't do that
if pmd_numa() is also set. Note that the NUMA bit only gets set on real
NUMA machines, so people trying to reproduce this on most normal
development systems would never actually trigger this.
Fix it by removing the very subtle (and subtly incorrect) expectation,
and instead just checking pmd_trans_huge() explicitly.
Reported-by: Sasha Levin <sasha.levin@oracle.com>
Acked-by: Andrea Arcangeli <aarcange@redhat.com>
[ Additionally remove the now stale test for pmd_trans_huge() inside the
pmd_bad() case - Linus ]
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/horms/renesas into fixes
From Simon Horman:
Renesas ARM based SoC fixes for v3.13
* r8a7790 (R-Car H1) SoC
- Correct GPIO resources in DT.
This problem has been present since GPIOs were added to the r8a7790 SoC
by f98e10c88aa95bf7 ("ARM: shmobile: r8a7790: Add GPIO controller
devices to device tree") in v3.12-rc1.
* irqchip renesas-intc-irqpin
- Correct register bitfield shift calculation
This bug has been present since the renesas-intc-irqpin driver was
introduced by 443580486e3b9657 ("irqchip: Renesas INTC External IRQ pin
driver") in v3.10-rc1
* Lager board
- Do not build the phy fixup unless CONFIG_PHYLIB is enabled
This problem was introduced by 48c8b96f21817aad
* tag 'renesas-fixes-for-v3.13' of git://git.kernel.org/pub/scm/linux/kernel/git/horms/renesas:
ARM: shmobile: r8a7790: Fix GPIO resources in DTS
irqchip: renesas-intc-irqpin: Fix register bitfield shift calculation
ARM: shmobile: lager: phy fixup needs CONFIG_PHYLIB
Signed-off-by: Kevin Hilman <khilman@linaro.org>
|
|
Patch queue for 3.13 - 2013-12-18
This fixes some grave issues we've only found after 3.13-rc1:
- Make the modularized HV/PR book3s kvm work well as modules
- Fix some race conditions
- Fix compilation with certain compilers (booke)
- Fix THP for book3s_hv
- Fix preemption for book3s_pr
Alexander Graf (4):
KVM: PPC: Book3S: PR: Don't clobber our exit handler id
KVM: PPC: Book3S: PR: Export kvmppc_copy_to|from_svcpu
KVM: PPC: Book3S: PR: Make svcpu -> vcpu store preempt savvy
KVM: PPC: Book3S: PR: Enable interrupts earlier
Aneesh Kumar K.V (1):
powerpc: book3s: kvm: Don't abuse host r2 in exit path
Paul Mackerras (5):
KVM: PPC: Book3S HV: Fix physical address calculations
KVM: PPC: Book3S HV: Refine barriers in guest entry/exit
KVM: PPC: Book3S HV: Make tbacct_lock irq-safe
KVM: PPC: Book3S HV: Take SRCU read lock around kvm_read_guest() call
KVM: PPC: Book3S HV: Don't drop low-order page address bits
Scott Wood (1):
powerpc/kvm/booke: Fix build break due to stack frame size warning
pingfan liu (1):
powerpc: kvm: fix rare but potential deadlock scene
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/xen/tip
Pull Xen bugfixes from Konrad Rzeszutek Wilk:
- Fix balloon driver for auto-translate guests (PVHVM, ARM) to not use
scratch pages.
- Fix block API header for ARM32 and ARM64 to have proper layout
- On ARM when mapping guests, stick on PTE_SPECIAL
- When using SWIOTLB under ARM, don't call swiotlb functions twice
- When unmapping guests memory and if we fail, don't return pages which
failed to be unmapped.
- Grant driver was using the wrong address on ARM.
* tag 'stable/for-linus-3.13-rc4-tag' of git://git.kernel.org/pub/scm/linux/kernel/git/xen/tip:
xen/balloon: Seperate the auto-translate logic properly (v2)
xen/block: Correctly define structures in public headers on ARM32 and ARM64
arm: xen: foreign mapping PTEs are special.
xen/arm64: do not call the swiotlb functions twice
xen: privcmd: do not return pages which we have failed to unmap
XEN: Grant table address, xen_hvm_resume_frames, is a phys_addr not a pfn
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/rostedt/linux-trace
Pull ftrace fix from Steven Rostedt:
"This fixes a long standing bug in the ftrace profiler. The problem is
that the profiler only initializes the online CPUs, and not possible
CPUs. This causes issues if the user takes CPUs online or offline
while the profiler is running.
If we online a CPU after starting the profiler, we lose all the trace
information on the CPU going online.
If we offline a CPU after running a test and start a new test, it will
not clear the old data from that CPU.
This bug causes incorrect data to be reported to the user if they
online or offline CPUs during the profiling"
* tag 'trace-fixes-v3.13-rc2' of git://git.kernel.org/pub/scm/linux/kernel/git/rostedt/linux-trace:
ftrace: Initialize the ftrace profiler for each possible cpu
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/tmlind/linux-omap into fixes
I accidentally removed some mux code for omap4 that I thought was
dead code as omap4 has been booting with device tree only since
v3.10. Turns out I also removed some display related mux code,
so let's revert that except for the dead code parts.
* tag 'omap-for-v3.13/display-fix' of git://git.kernel.org/pub/scm/linux/kernel/git/tmlind/linux-omap: (439 commits)
Revert "ARM: OMAP2+: Remove legacy mux code for display.c"
+Linux 3.13-rc4
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/ssantosh/linux-keystone into fixes
From Santosh Shilimkar:
Couple of updates to MAINTAINERS file for Keystone
- Add git tree information
- Add clock drivers entry
* tag 'keystone/maintainer-file' of git://git.kernel.org/pub/scm/linux/kernel/git/ssantosh/linux-keystone:
MAINTAINERS: Add keystone clock drivers
MAINTAINERS: Add keystone git tree information
Signed-off-by: Kevin Hilman <khilman@linaro.org>
|
|
This patch fixes a possible scsi_host reference leak in qlt_lport_register(),
when a non zero return from the passed (*callback) does not call drop the
local reference via scsi_host_put() before returning.
This currently does not effect existing tcm_qla2xxx code as the passed callback
will never fail, but fix this up regardless for future code.
Cc: Chad Dupuis <chad.dupuis@qlogic.com>
Signed-off-by: Nicholas Bellinger <nab@linux-iscsi.org>
|
|
lun->lun_ref is also initialized in core_tpg_post_addlun, so it doesn't
need to be done in core_tpg_setup_virtual_lun0.
(nab: Drop left-over percpu_ref_cancel_init in failure path)
Signed-off-by: Andy Grover <agrover@redhat.com>
Signed-off-by: Nicholas Bellinger <nab@linux-iscsi.org>
|
|
New driver for NXP (Philips) UART ICs was introduced in September 2012.
Old driver no longer used anywhere, this patch removes it.
Signed-off-by: Alexander Shiyan <shc_work@mail.ru>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
Signed-off-by: Yegor Yefremov <yegorslists@googlemail.com>
Cc: stable <stable@vger.kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
Fix the initialisation of older Quatech serial cards which are fitted with
the AMCC PCI Matchmaker interface chip.
Signed-off-by: Jonathan Woithe (jwoithe@just42.net)
Cc: stable <stable@vger.kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
Commit 8f34a1da35ae ("arm64: ptrace: use HW_BREAKPOINT_EMPTY type for
disabled breakpoints") fixed an issue with GDB trying to zero breakpoint
control registers. The problem there is that the arch hw_breakpoint code
will attempt to create a (disabled), execute breakpoint of length 0.
This will fail validation and report unexpected failure to GDB. To avoid
this, we treated disabled breakpoints as HW_BREAKPOINT_EMPTY, but that
seems to have broken with recent kernels, causing watchpoints to be
treated as TYPE_INST in the core code and returning ENOSPC for any
further breakpoints.
This patch fixes the problem by prioritising the `enable' field of the
breakpoint: if it is cleared, we simply update the perf_event_attr to
indicate that the thing is disabled and don't bother changing either the
type or the length. This reinforces the behaviour that the breakpoint
control register is essentially read-only apart from the enable bit
when disabling a breakpoint.
Cc: <stable@vger.kernel.org>
Reported-by: Aaron Liu <liucy214@gmail.com>
Signed-off-by: Will Deacon <will.deacon@arm.com>
Signed-off-by: Catalin Marinas <catalin.marinas@arm.com>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip
Pull scheduler fixes from Ingo Molnar:
"An RT group-scheduling fix and the sched-domains topology setup fix
from Mel"
* 'sched-urgent-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
sched/rt: Fix rq's cpupri leak while enqueue/dequeue child RT entities
sched: Assign correct scheduling domain to 'sd_llc'
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip
Pull perf fixes from Ingo Molnar:
"An ABI documentation fix, and a mixed-PMU perf-info-corruption fix"
* 'perf-urgent-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
perf: Document the new transaction sample type
perf: Disable all pmus on unthrottling and rescheduling
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/tiwai/sound
Pull sound fixes from Takashi Iwai:
"We have a bit more changes than usual in ASoC here, as it was slipped
from the previous update. There are one minr ASoC PCM code fix and
ASoC dmaengine fix, in addition of a collection of small ASoC driver
fixes. The rest are a couple of HD-audio stable fixups, and a
long-standing fix for the paused stream handling.
So, all commits look not scary (and hopefully won't give you
disastrous holiday season)"
* tag 'sound-3.13-rc5' of git://git.kernel.org/pub/scm/linux/kernel/git/tiwai/sound:
ALSA: hda - Add Dell headset detection quirk for one more laptop model
ASoC: wm8904: fix DSP mode B configuration
ASoC: wm_adsp: Add small delay while polling DSP RAM start
ALSA: Add SNDRV_PCM_STATE_PAUSED case in wait_for_avail function
ASoC: kirkwood: Fix the CPU DAI rates
ASoC: wm5110: Correct HPOUT3 DAPM route typo
ALSA: hda - Add Dell headset detection quirk for three laptop models
ALSA: hda - Add enable_msi=0 workaround for four HP machines
ASoC: don't leak on error in snd_dmaengine_pcm_register
ASoC: fsl: imx-wm8962: Don't update bias_level in machine driver
ASoC: tegra: fix uninitialized variables in set_fmt
ASoC: wm8962: Enable SYSCLK provisonally before fetching generated DSPCLK_DIV
ASoC: sam9x5_wm8731: change to work in DSP A mode
ASoC: atmel_ssc_dai: add dai trigger ops
ASoC: soc-pcm: Use valid condition for snd_soc_dai_digital_mute() in hw_free()
|
