Age | Commit message (Collapse) | Author |
|
Gigabyte netbook model M1022M requires i8042.noloop, otherwise AUX port
will not detected and the touchpad will not work. Unfortunately chassis
type in DMI set to "Other" and thus generic laptop entry does not fire
on it.
Reported-by: Darryl Bond <dbond@nrggos.com.au>
Signed-off-by: Dmitry Torokhov <dtor@mail.ru>
|
|
Some hardware (such as Dell laptops) signal a variety of events through
the i8042 controller, even if these don't map to keyboard events. Add
support for drivers to filter the i8042 event stream in order to respond
to these events and (if appropriate) block them from entering the input
stream.
Signed-off-by: Matthew Garrett <mjg@redhat.com>
Signed-off-by: Dmitry Torokhov <dtor@mail.ru>
|
|
We need to protect not only i8042 status and data register from concurrent
access from IRQ 1 and 12 but the rest of the shared state as well, so let's
move release of i8042_lock in i8042_interrupt() a little bit further down.
Signed-off-by: Dmitry Torokhov <dtor@mail.ru>
|
|
Relative events are only reported via secondary device therefore device
associated with the touchpad should not advertise these capabilities.
Signed-off-by: Dmitry Torokhov <dtor@mail.ru>
|
|
Acked-by: Henrique de Moraes Holschuh <hmh@hmh.eng.br>
Signed-off-by: Dmitry Torokhov <dtor@mail.ru>
|
|
Also fix annotation of ps2_test() - it can'be __init since it is called
from __devinit code.
Signed-off-by: Dmitry Torokhov <dtor@mail.ru>
|
|
Signed-off-by: Dmitry Torokhov <dtor@mail.ru>
|
|
Signed-off-by: Dmitry Torokhov <dtor@mail.ru>
|
|
Mark altera_ps2_probe() as __devinit and altera_ps2_remove() as __devexit
so that they can be discarded when not needed.
Signed-off-by: Dmitry Torokhov <dtor@mail.ru>
|
|
del_timer() does not wait for the timer to finish running before returning
and therefore is technically not safe. Also make sure to enable tasklet
before kicking timer that will schedule it.
Signed-off-by: Dmitry Torokhov <dtor@mail.ru>
|
|
Setting up owner field ensures that driver core creates symlink from
the driver to a module implementing this driver.
Signed-off-by: Dmitry Torokhov <dtor@mail.ru>
|
|
I no longer have a machine with this, and as such am not really able
to help out with this driver any more. Remove the entire appletouch
section and let the driver fall under the general input subsystem.
Signed-off-by: Johannes Berg <johannes@sipsolutions.net>
Signed-off-by: Dmitry Torokhov <dtor@mail.ru>
|
|
Signed-off-by: Dmitry Torokhov <dtor@mail.ru>
|
|
The keymap manipulation code was split into a library module,
so let's make us of it.
Signed-off-by: Dmitry Torokhov <dtor@mail.ru>
|
|
More and more devices choose to reimplement support for sparse keymaps
first introduced by wistron driver. Move it into a library module so it
can be easily used by interested parties.
Reviewed-by: Anisse Astier <anisse@astier.eu>
Signed-off-by: Dmitry Torokhov <dtor@mail.ru>
|
|
Effects were allocated, but not freed anywhere.
Signed-off-by: Jari Vanhala <ext-jari.vanhala@nokia.com>
Signed-off-by: Dmitry Torokhov <dtor@mail.ru>
|
|
The driver does not reference identification strings in DMI table and
since these strings are no longer required by DMI core we can safely
remove them and save some memory.
Signed-off-by: Dmitry Torokhov <dtor@mail.ru>
|
|
The driver does not reference identification strings in DMI tables and
since these strings are no longer required by DMI core we can safely
remove them and save some memory.
Signed-off-by: Dmitry Torokhov <dtor@mail.ru>
|
|
The driver does not reference identification strings in DMI table and
since these strings are no longer required by DMI core we can safely
remove them and save some memory.
Signed-off-by: Dmitry Torokhov <dtor@mail.ru>
|
|
The driver does not reference identification strings in DMI tables and
since these strings are no longer required by DMI core we can safely
remove them and save some memory.
Signed-off-by: Dmitry Torokhov <dtor@mail.ru>
|
|
The purpose of dmi->ident is twofold - it may be used by DMI callback
functions when composing log messages; it is also used to determine
end of DMI table in dmi_check_system() and dmi_first_match(). However,
in case when callbacks are not interested in using ident at all it just
wastes memory. Let's make entries with empty first match slot serve as
end-of-table markers instead.
Acked-by: Jean Delvare <khali@linux-fr.org>
Signed-off-by: Dmitry Torokhov <dtor@mail.ru>
|
|
DMI tables use considerable amount of memory. Mark them as __initconst
so they will be discarded once module is loaded.
Signed-off-by: Dmitry Torokhov <dtor@mail.ru>
|
|
Acked-by: Rafael J. Wysocki <rjw@sisk.pl>
Signed-off-by: Dmitry Torokhov <dtor@mail.ru>
|
|
|
|
|
|
request_region should be used with release_region, not request_mem_region.
Geert Uytterhoeven pointed out that in the case of drivers/video/gbefb.c,
the problem is actually the other way around; request_mem_region should be
used instead of request_region.
The semantic patch that finds/fixes this problem is as follows:
(http://coccinelle.lip6.fr/)
// <smpl>
@r1@
expression start;
@@
request_region(start,...)
@b1@
expression r1.start;
@@
request_mem_region(start,...)
@depends on !b1@
expression r1.start;
expression E;
@@
- release_mem_region
+ release_region
(start,E)
// </smpl>
Signed-off-by: Julia Lawall <julia@diku.dk>
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
|
|
TXx9 SPI bit rate is calculated by:
fBR = (spi-baseclk) / (n + 1)
Fix calculation of min_speed_hz, max_speed_hz and n.
Signed-off-by: Atsushi Nemoto <anemo@mba.ocn.ne.jp>
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/sameo/mfd-2.6
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/sameo/mfd-2.6:
mfd: Correct WM831X_MAX_ISEL_VALUE
|
|
These laptops often leave i8042 in a wierd state resulting in non-
operational touchpad and keyboard.
Signed-off-by: Anisse Astier <anisse@astier.eu>
Signed-off-by: Dmitry Torokhov <dtor@mail.ru>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
|
|
* 'for-linus' of git://neil.brown.name/md:
md: revert incorrect fix for read error handling in raid1.
|
|
Jon confirms that recent modprobe will look in /proc/cmdline, so these
cmdline options can still be used.
See http://bugzilla.kernel.org/show_bug.cgi?id=14164
Reported-by: Adam Williamson <awilliam@redhat.com>
Cc: stable@kernel.org
Signed-off-by: Rusty Russell <rusty@rustcorp.com.au>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
|
|
* 'upstream' of git://ftp.linux-mips.org/pub/scm/upstream-linus:
MIPS: RB532: Fix devices.c compilation.
MIPS: Fix MIPS I build.
|
|
* git://git.kernel.org/pub/scm/linux/kernel/git/wim/linux-2.6-watchdog:
[PATCH] rc32434_wdt: fix compilation failure
[WATCHDOG] rc32434_wdt.c: use resource_size()
|
|
On the parisc architecture we face for each and every loaded kernel module
this kernel "badness warning":
sysfs: cannot create duplicate filename '/module/ac97_bus/sections/.text'
Badness at fs/sysfs/dir.c:487
Reason for that is, that on parisc all kernel modules do have multiple
.text sections due to the usage of the -ffunction-sections compiler flag
which is needed to reach all jump targets on this platform.
An objdump on such a kernel module gives:
Sections:
Idx Name Size VMA LMA File off Algn
0 .note.gnu.build-id 00000024 00000000 00000000 00000034 2**2
CONTENTS, ALLOC, LOAD, READONLY, DATA
1 .text 00000000 00000000 00000000 00000058 2**0
CONTENTS, ALLOC, LOAD, READONLY, CODE
2 .text.ac97_bus_match 0000001c 00000000 00000000 00000058 2**2
CONTENTS, ALLOC, LOAD, READONLY, CODE
3 .text 00000000 00000000 00000000 000000d4 2**0
CONTENTS, ALLOC, LOAD, READONLY, CODE
...
Since the .text sections are empty (size of 0 bytes) and won't be
loaded by the kernel module loader anyway, I don't see a reason
why such sections need to be listed under
/sys/module/<module_name>/sections/<section_name> either.
The attached patch does solve this issue by not exporting section
names which are empty.
This fixes bugzilla http://bugzilla.kernel.org/show_bug.cgi?id=14703
Signed-off-by: Helge Deller <deller@gmx.de>
CC: rusty@rustcorp.com.au
CC: akpm@linux-foundation.org
CC: James.Bottomley@HansenPartnership.com
CC: roland@redhat.com
CC: dave@hiauly1.hia.nrc.ca
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/lrg/voltage-2.6
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/lrg/voltage-2.6:
regulator: Initialise wm831x structure pointor for ISINK driver
|
|
The version that made it into mainline missed the initialisation of the
chip handle.
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Signed-off-by: Liam Girdwood <lrg@slimlogic.co.uk>
|
|
We should now use dev_set_drvdata to set the driver driver_data field.
Signed-off-by: Florian Fainelli <florian@openwrt.org>
Patchwork: http://patchwork.linux-mips.org/patch/747/
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
|
|
Broken by d63c63e889bbeeaa461a8addf1245f89f3ce4ece (lmo) rsp.
f1e39a4a616cd9981a9decfd5332fd07a01abb8b (kernel.org).
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
Patchwork: http://patchwork.linux-mips.org/patch/746/
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/ycmiao/pxa-linux-2.6
* 'fix' of git://git.kernel.org/pub/scm/linux/kernel/git/ycmiao/pxa-linux-2.6:
[ARM] pxamci: call mmc_remove_host() before freeing resources
|
|
mmc_remove_host() will cause the mmc core to switch off the bus power by
eventually calling pxamci_set_ios(). This function uses the regulator or
the GPIO which have been freed already.
This causes the following Oops on module unload.
[ 49.519649] Unable to handle kernel paging request at virtual address 30303a70
[ 49.526878] pgd = c7084000
[ 49.529563] [30303a70] *pgd=00000000
[ 49.533136] Internal error: Oops: 5 [#1]
[ 49.537025] last sysfs file: /sys/devices/platform/pxa27x-ohci/usb1/1-1/1-1:1.0/host0/target0:0:0/0:0:0:0/scsi_level
[ 49.547471] Modules linked in: pxamci(-) eeti_ts
[ 49.552061] CPU: 0 Not tainted (2.6.32-rc8 #322)
[ 49.557001] PC is at regulator_is_enabled+0x3c/0xbc
[ 49.561846] LR is at regulator_is_enabled+0x30/0xbc
[ 49.566691] pc : [<c01a2448>] lr : [<c01a243c>] psr: 60000013
[ 49.566702] sp : c7083e70 ip : 30303a30 fp : 00000000
[ 49.578093] r10: c705e200 r9 : c7082000 r8 : c705e2e0
[ 49.583280] r7 : c7061340 r6 : c7061340 r5 : c7083e70 r4 : 00000000
[ 49.589759] r3 : c04dc434 r2 : c04dc434 r1 : c03eecea r0 : 00000047
[ 49.596241] Flags: nZCv IRQs on FIQs on Mode SVC_32 ISA ARM Segment user
[ 49.603329] Control: 0000397f Table: a7084018 DAC: 00000015
[ 49.609031] Process rmmod (pid: 1101, stack limit = 0xc7082278)
[ 49.614908] Stack: (0xc7083e70 to 0xc7084000)
[ 49.619238] 3e60: c7082000 c703c4f8 c705ea00 c04f4074
[ 49.627366] 3e80: 00000000 c705e3a0 ffffffff c0247ddc c70361a0 00000000 c705e3a0 ffffffff
[ 49.635499] 3ea0: c705e200 bf006400 c78c4f00 c705e200 c705e3a0 ffffffff c705e200 ffffffff
[ 49.643633] 3ec0: c04d8ac8 c02476d0 ffffffff c0247c60 c705e200 c0248678 c705e200 c0249064
[ 49.651765] 3ee0: ffffffff bf006204 c04d8ad0 c04d8ad0 c04d8ac8 bf007490 00000880 c00440c4
[ 49.659898] 3f00: 0000b748 c01c5708 bf007490 c01c44c8 c04d8ac8 c04d8afc bf007490 c01c4570
[ 49.668031] 3f20: bf007490 bf00750c c04f4258 c01c37a4 00000000 bf00750c c7083f44 c007b014
[ 49.676162] 3f40: 4000d000 6d617870 08006963 00000001 00000000 c7085000 00000001 00000000
[ 49.684287] 3f60: 4000d000 c7083f8c 00000001 bea01a54 00005401 c7ab1400 c00440c4 00082000
[ 49.692420] 3f80: bf00750c 00000880 c7083f8c 00000000 4000cfa8 00000000 00000880 bea01cc8
[ 49.700552] 3fa0: 00000081 c0043f40 00000000 00000880 bea01cc8 00000880 00000006 00000000
[ 49.708677] 3fc0: 00000000 00000880 bea01cc8 00000081 00000097 0000cca4 0000b748 00000000
[ 49.716802] 3fe0: 4001a4f0 bea01cc0 00018bf4 4001a4fc 20000010 bea01cc8 a063e021 a063e421
[ 49.724958] [<c01a2448>] (regulator_is_enabled+0x3c/0xbc) from [<c0247ddc>] (mmc_regulator_set_ocr+0x14/0xd8)
[ 49.734836] [<c0247ddc>] (mmc_regulator_set_ocr+0x14/0xd8) from [<bf006400>] (pxamci_set_ios+0xd8/0x17c [pxamci])
[ 49.745044] [<bf006400>] (pxamci_set_ios+0xd8/0x17c [pxamci]) from [<c02476d0>] (mmc_power_off+0x50/0x58)
[ 49.754555] [<c02476d0>] (mmc_power_off+0x50/0x58) from [<c0247c60>] (mmc_detach_bus+0x68/0xc4)
[ 49.763207] [<c0247c60>] (mmc_detach_bus+0x68/0xc4) from [<c0248678>] (mmc_stop_host+0xd4/0x1bc)
[ 49.771944] [<c0248678>] (mmc_stop_host+0xd4/0x1bc) from [<c0249064>] (mmc_remove_host+0xc/0x20)
[ 49.780681] [<c0249064>] (mmc_remove_host+0xc/0x20) from [<bf006204>] (pxamci_remove+0xc8/0x174 [pxamci])
[ 49.790211] [<bf006204>] (pxamci_remove+0xc8/0x174 [pxamci]) from [<c01c5708>] (platform_drv_remove+0x1c/0x24)
[ 49.800164] [<c01c5708>] (platform_drv_remove+0x1c/0x24) from [<c01c44c8>] (__device_release_driver+0x7c/0xc4)
[ 49.810110] [<c01c44c8>] (__device_release_driver+0x7c/0xc4) from [<c01c4570>] (driver_detach+0x60/0x8c)
[ 49.819535] [<c01c4570>] (driver_detach+0x60/0x8c) from [<c01c37a4>] (bus_remove_driver+0x90/0xcc)
[ 49.828452] [<c01c37a4>] (bus_remove_driver+0x90/0xcc) from [<c007b014>] (sys_delete_module+0x1d8/0x254)
[ 49.837891] [<c007b014>] (sys_delete_module+0x1d8/0x254) from [<c0043f40>] (ret_fast_syscall+0x0/0x28)
[ 49.847145] Code: eb06c53a e596c030 e1a0500d e59f106c (e59c0040)
[ 49.853566] ---[ end trace b5fa66a00cea142f ]---
Signed-off-by: Daniel Mack <daniel@caiaq.de>
Reported-by: Sven Neumann <s.neumann@raumfeld.com>
Cc: Pierre Ossman <pierre@ossman.eu>
Cc: linux-mmc@vger.kernel.org
Cc: linux-arm-kernel@lists.infradead.org
Cc: stable@kernel.org
Signed-off-by: Eric Miao <eric.y.miao@gmail.com>
|
|
This patch fixes the compilation failure of
rc32434 due to a bad module parameter description.
Signed-off-by: Florian Fainelli <florian@openwrt.org>
Signed-off-by: Wim Van Sebroeck <wim@iguana.be>
|
|
The size value passed to ioremap_nocache() is not correct.
Use resource_size() to get the correct value.
Signed-off-by: H Hartley Sweeten <hsweeten@visionengravers.com>
Cc: Phil Sutter <n0-1@freewrt.org>
Signed-off-by: Wim Van Sebroeck <wim@iguana.be>
|
|
Keyboard handler should not attempt to traverse handler->h_list on
its own, without any locking, otherwise it races with registering
and unregistering of input handles which leads to crashes.
Introduce input_handler_for_each_handle() helper that allows safely
iterate over all handles attached to a particular handler and switch
keyboard handler to use it.
Reported-by: Jim Paradis <jparadis@redhat.com>
Signed-off-by: Dmitry Torokhov <dtor@mail.ru>
|
|
The SYSFS_DEPRECATED_V2 says "remove" older, deprecated features, but it
actually enables them, so correct this confusing, backwards text.
Signed-off-by: Randy Dunlap <randy.dunlap@oracle.com>
Cc: Kay Sievers <kay.sievers@vrfy.org>
Cc: Greg KH <greg@kroah.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
|
|
When detecting power failure, the probe function would reset the clock
time to defined state.
However, the clock's _date_ might still be bogus and a subsequent probe
fails when sanity-checking these values.
Change the power-failure fixup code to do a full setting of rtc_time,
including a valid date.
Signed-off-by: Johannes Weiner <jw@emlix.com>
Cc: Alessandro Zummo <a.zummo@towertech.it>
Cc: Paul Gortmaker <p_gortmaker@yahoo.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
|
|
The possible CCR_Y2K register values are 19 or 20 and struct rtc_time's
tm_year is in years since 1900.
The function translating rtc_time to register values assumes tm_year to be
years since first christmas, though, and we end up storing 0 or 1 in the
CCR_Y2K register, which the hardware does not refuse to do.
A subsequent probing of the clock fails due to the invalid value range in
the register, though.
[ And if it didn't, reading the clock would yield a bogus year because
the function translating registers to tm_year is assuming a register
value of 19 or 20. ]
This fixes the conversion from years since 1900 in tm_year to the
corresponding CCR_Y2K value of 19 or 20.
Signed-off-by: Johannes Weiner <jw@emlix.com>
Cc: Alessandro Zummo <a.zummo@towertech.it>
Cc: Paul Gortmaker <p_gortmaker@yahoo.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
|
|
Prevent the AoE block driver from creating cache aliases of page cache
pages on machines with virtually indexed caches.
Building kernels on an AT91SAM9G20 board without this patch fails with
segmentation faults after a couple of passes.
Signed-off-by: Peter Horton <zero@colonel-panic.org>
Cc: "Ed L. Cashin" <ecashin@coraid.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
|
|
- Remove wrong and unnecessary unmask operation
- Remove extra GEDR reading
This fixes the loss of interrupts which occurs when two or more pins are
triggered in close succession.
Signed-off-by: Alek Du <alek.du@intel.com>
Cc: David Brownell <david-b@pacbell.net>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
|
|
It has been fun but the last year or more it has been a duty and a burden.
So I leave it open for others to take over.
Signed-off-by: Sam Ravnborg <sam@ravnborg.org>
Cc: Anibal Monsalve Salazar <anibal@debian.org>
Cc: Steven Rostedt <rostedt@goodmis.org>
Cc: Michal Marek <mmarek@suse.cz>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
|
|
Following issues have been addressed on DA8XX/OMAP-L1XX:
a. Screen misalignment during booting when frame buffer console is
enabled.
b. Driver was configured always in PSEUDOCOLOR mode. This patch
dynamically configures the driver either in PSEUDOCOLOUR or TRUECOLOR
mode depending on bpp.
c. The RED and BLUE offsets were interchanged resulting in wrong
bootup logo colour.
This patch has been tested on DA830/OMAP-L137 and DA850/OMAP-L138 EVMs.
Signed-off-by: Sudhakar Rajashekhara <sudhakar.raj@ti.com>
Cc: Steve Chen <schen@mvista.com>
Cc: Pavel Kiryukhin <pkiryukhin@ru.mvista.com>
Cc: Krzysztof Helt <krzysztof.h1@wp.pl>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
|