| Age | Commit message (Collapse) | Author |
|---|
|
In the case where "task" requests timeout (note that this class of
requests can also include SATA/STP soft reset FIS transmissions),
handle the case where the task was being managed by some call to
terminate the task request by completing both the tmf and the aborting
process.
Signed-off-by: Jeff Skirvin <jeffrey.d.skirvin@intel.com>
Signed-off-by: Dan Williams <dan.j.williams@intel.com>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>
|
|
Make sure terminated requests and completed task tags are freed.
Signed-off-by: Jeff Skirvin <jeffrey.d.skirvin@intel.com>
Signed-off-by: Dan Williams <dan.j.williams@intel.com>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>
|
|
In the case where an I/O fails to start in isci_request_execute,
only allow retries if the device is not already gone.
Signed-off-by: Jeff Skirvin <jeffrey.d.skirvin@intel.com>
Signed-off-by: Dan Williams <dan.j.williams@intel.com>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>
|
|
The LLDD needs to obtain a reference to the device through the request
itself and not through the domain_device, because the
domain_device.lldd_dev is set to NULL early in the lldd_dev_gone call.
This relies on the fact that the isci_remote_device object is keeping a
seperate reference count of outstanding requests. TODO: unify the
request count tracking with the isci_remote_device kref.
The failure signature of this condition looks like the following
log, where the important bits are the call to lldd_dev_gone followed
by a crash in isci_terminate_request_core:
[ 229.151541] isci 0000:0b:00.0: isci_remote_device_gone: domain_device = ffff8801492d4800, isci_device = ffff880143c657d0, isci_port = ffff880143c63658
[ 229.166007] isci 0000:0b:00.0: isci_remote_device_stop: isci_device = ffff880143c657d0
[ 229.175317] isci 0000:0b:00.0: isci_terminate_pending_requests: idev=ffff880143c657d0 request=ffff88014741f000; task=ffff8801470f46c0 old_state=2
[ 229.189702] isci 0000:0b:00.0: isci_terminate_request_core: device = ffff880143c657d0; request = ffff88014741f000
[ 229.201339] isci 0000:0b:00.0: isci_terminate_request_core: before completion wait (ffff88014741f000/ffff880149715ad0)
[ 229.213414] isci 0000:0b:00.0: sci_controller_process_completions: completion queue entry:0x8000a0e9
[ 229.214401] BUG: unable to handle kernel NULL pointer dereference at 0000000000000228
[ 229.214401] IP:jdskirvi-testlbo [<ffffffffa00a58be>] sci_request_completed_state_enter+0x50/0xafb [isci]
[ 229.214401] PGD 13d19e067 PUD 13d104067 PMD 0
[ 229.214401] Oops: 0000 [#1] SMP
[ 229.214401] CPU 0 x kernel: [ 226
[ 229.214401] Modules linked in: ipv6 dm_multipath uinput nouveau snd_hda_codec_realtek snd_hda_intel ttm drm_kms_helper drm snd_hda_codec snd_hwdep snd_pcm snd_timer i2c_algo_bit isci snd libsas ioatdma mxm_wmi iTCO_wdt soundcore snd_page_alloc scsi_transport_sas iTCO_vendor_support wmi dca video i2c_i801 i2c_core [last unloaded: speedstep_lib]
[ 229.214401]
[ 229.214401] Pid: 5, comm: kworker/u:0 Not tainted 3.0.0-isci-11.7.29+ #30.353196] Buffer Intel Corporation Stoakley/Pearlcity Workstation
[ 229.214401] RIP: 0010:[<ffffffffa00a58be>] I/O error on dev [<ffffffffa00a58be>] sci_request_completed_state_enter+0x50/0xafb [isci]
[ 229.214401] RSP: 0018:ffff88014fc03d20 EFLAGS: 00010046
[ 229.214401] RAX: 0000000000000000 RBX: ffff88014741f000 RCX: 0000000000000000
[ 229.214401] RDX: ffffffffa00b2c90 RSI: 0000000000000017 RDI: ffff88014741f0a0
[ 229.214401] RBP: ffff88014fc03d90 R08: 0000000000000018 R09: 0000000000000000
[ 229.214401] R10: 0000000000000000 R11: ffffffff81a17d98 R12: 000000000000001d
[ 229.214401] R13: ffff8801470f46c0 R14: 0000000000000000 R15: 0000000000008000
[ 229.214401] FS: 0000000000000000(0000) GS:ffff88014fc00000(0000) knlGS:0000000000000000
[ 229.214401] CS: 0010 DS: 0000 ES: 0000 CR0: 000000008005003b
[ 229.214401] CR2: 0000000000000228 CR3: 000000013ceaa000 CR4: 00000000000406f0
[ 229.214401] DR0: 0000000000000000 DR1: 0000000000000000 DR2: 0000000000000000
[ 229.214401] DR3: 0000000000000000 DR6: 00000000ffff0ff0 DR7: 0000000000000400
[ 229.214401] Process kworker/u:0 (pid: 5, threadinfo ffff880149714000, task ffff880149718000)
[ 229.214401] Call Trace:
[ 229.214401] <IRQ>
[ 229.214401] [<ffffffffa00aa6ce>] sci_change_state+0x4a/0x4f [isci]
[ 229.214401] [<ffffffffa00a4ca6>] sci_io_request_tc_completion+0x79c/0x7a0 [isci]
[ 229.214401] [<ffffffffa00acf35>] sci_controller_process_completions+0x14f/0x396 [isci]
[ 229.214401] [<ffffffffa00abbda>] ? spin_lock_irq+0xe/0x10 [isci]
[ 229.214401] [<ffffffffa00ad2cf>] isci_host_completion_routine+0x71/0x2be [isci]
[ 229.214401] [<ffffffff8107c6b3>] ? mark_held_locks+0x52/0x70
[ 229.214401] [<ffffffff810538e8>] tasklet_action+0x90/0xf1
[ 229.214401] [<ffffffff81054050>] __do_softirq+0xe5/0x1bf
[ 229.214401] [<ffffffff8106d9d1>] ? hrtimer_interrupt+0x129/0x1bb
[ 229.214401] [<ffffffff814ff69c>] call_softirq+0x1c/0x30
[ 229.214401] [<ffffffff8100bb67>] do_softirq+0x4b/0xa3
[ 229.214401] [<ffffffff81053d84>] irq_exit+0x53/0xb4
[ 229.214401] [<ffffffff814fffe7>] smp_apic_timer_interrupt+0x83/0x91
[ 229.214401] [<ffffffff814fee53>] apic_timer_interrupt+0x13/0x20
[ 229.214401] <EOI>
[ 229.214401] [<ffffffff814f7ad4>] ? retint_restore_args+0x13/0x13
[ 229.214401] [<ffffffff8107af29>] ? trace_hardirqs_off+0xd/0xf
[ 229.214401] [<ffffffff8104ea71>] ? vprintk+0x40b/0x452
[ 229.214401] [<ffffffff814f4b5a>] printk+0x41/0x47
[ 229.214401] [<ffffffff81314484>] __dev_printk+0x78/0x7a
[ 229.214401] [<ffffffff8131471e>] dev_printk+0x45/0x47
[ 229.214401] [<ffffffffa00ae2a3>] isci_terminate_request_core+0x15d/0x317 [isci]
[ 229.214401] [<ffffffffa00af1ad>] isci_terminate_pending_requests+0x1a4/0x204 [isci]
[ 229.214401] [<ffffffffa00229f6>] ? sas_phye_oob_error+0xc3/0xc3 [libsas]
[ 229.214401] [<ffffffffa00a7d9e>] isci_remote_device_nuke_requests+0xa6/0xff [isci]
[ 229.214401] [<ffffffffa00a811a>] isci_remote_device_stop+0x7c/0x166 [isci]
[ 229.214401] [<ffffffffa00229f6>] ? sas_phye_oob_error+0xc3/0xc3 [libsas]
[ 229.214401] [<ffffffffa00a827a>] isci_remote_device_gone+0x76/0x7e [isci]
[ 229.214401] [<ffffffffa002363e>] sas_notify_lldd_dev_gone+0x34/0x36 [libsas]
[ 229.214401] [<ffffffffa0023945>] sas_unregister_dev+0x57/0x9c [libsas]
[ 229.214401] [<ffffffffa00239c0>] sas_unregister_domain_devices+0x36/0x65 [libsas]
[ 229.214401] [<ffffffffa0022cb8>] sas_deform_port+0x72/0x1ac [libsas]
[ 229.214401] [<ffffffffa00229f6>] ? sas_phye_oob_error+0xc3/0xc3 [libsas]
[ 229.214401] [<ffffffffa0022a34>] sas_phye_loss_of_signal+0x3e/0x42 [libsas]
Signed-off-by: Jeff Skirvin <jeffrey.d.skirvin@intel.com>
Signed-off-by: Dan Williams <dan.j.williams@intel.com>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>
|
|
Add the appropriate definition and table entry for an additional adapter.
Signed-off-by: Wayne Boyer <wayneb@linux.vnet.ibm.com>
Acked-by: Brian King <brking@linux.vnet.ibm.com>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>
|
|
This patch validates sdev pointer in scsi_dh_activate before proceeding further.
Without this check we might see the panic as below. I have seen this
panic multiple times..
Call trace:
#0 [ffff88007d647b50] machine_kexec at ffffffff81020902
#1 [ffff88007d647ba0] crash_kexec at ffffffff810875b0
#2 [ffff88007d647c70] oops_end at ffffffff8139c650
#3 [ffff88007d647c90] __bad_area_nosemaphore at ffffffff8102dd15
#4 [ffff88007d647d50] page_fault at ffffffff8139b8cf
[exception RIP: scsi_dh_activate+0x82]
RIP: ffffffffa0041922 RSP: ffff88007d647e00 RFLAGS: 00010046
RAX: 0000000000000000 RBX: 0000000000000000 RCX: 00000000000093c5
RDX: 00000000000093c5 RSI: ffffffffa02e6640 RDI: ffff88007cc88988
RBP: 000000000000000f R8: ffff88007d646000 R9: 0000000000000000
R10: ffff880082293790 R11: 00000000ffffffff R12: ffff88007cc88988
R13: 0000000000000000 R14: 0000000000000286 R15: ffff880037b845e0
ORIG_RAX: ffffffffffffffff CS: 0010 SS: 0000
#5 [ffff88007d647e38] run_workqueue at ffffffff81060268
#6 [ffff88007d647e78] worker_thread at ffffffff81060386
#7 [ffff88007d647ee8] kthread at ffffffff81064436
#8 [ffff88007d647f48] kernel_thread at ffffffff81003fba
Signed-off-by: Babu Moger <babu.moger@netapp.com>
Cc: stable@kernel.org
Signed-off-by: James Bottomley <JBottomley@Parallels.com>
|
|
When controller lockup condition is detected,
we should fail all outstanding commands and disable
the controller. This will enable multipath solutions
to recover gracefully.
Signed-off-by: Stephen M. Cameron <scameron@beardog.cce.hp.com>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>
|
|
We weren't filling in the transfer length of the
flush cache command (it transfers 4 bytes of zeroes).
Firmware didn't seem to be bothered by this, but it
should be fixed.
Signed-off-by: Stephen M. Cameron <scameron@beardog.cce.hp.com>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>
|
|
The currentsd[] array in hpsa_update_scsi_devices had room for
256 devices. The code was iterating over however many physical
and logical devices plus an additional number of possible external
MSA2XXX controllers, which together could potentially exceed 256.
We increased the size of the currentsd array to 1024 + 1024 + 32 + 1
elements to reflect a reasonable maximum possible number of devices
which might be encountered. We also don't just walk off the end
of the array if the array controller reports more devices than we
are prepared to handle, we just ignore the excessive devices.
Signed-off-by: Scott Teel <scott.teel@hp.com>
Signed-off-by: Stephen M. Cameron <scameron@beardog.cce.hp.com>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>
|
|
Rename HPSA_MAX_SCSI_DEVS_PER_HBA to HPSA_MAX_DEVICES
Signed-off-by: Scott Teel <scott.teel@hp.com>
Signed-off-by: Stephen M. Cameron <scameron@beardog.cce.hp.com>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>
|
|
Signed-off-by: Stephen M. Cameron <scameron@beardog.cce.hp.com>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>
|
|
Set the max hardware sectors in the SCSI host template to 8192
to allow for larger i/o's (8192 is the same limit the cciss
driver currently has.)
Signed-off-by: Stephen M. Cameron <scameron@beardog.cce.hp.com>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>
|
|
During heavy I/O (CPU-affinity mode enabled) and CLI/Agent
interactions, the driver would report periodic mailbox command
timeout statuses. Within the CPU-affinity ISR handler, the
driver should check the 'disable-msix-handshake' flag in deciding
whether or not to clear HCCRX_CLR_RISC_INT. The mode is not
specific to a dedicated queue, instead, applies to the current
'ha' context.
Signed-off-by: Andrew Vasquez <andrew.vasquez@qlogic.com>
Signed-off-by: Chad Dupuis <chad.dupuis@qlogic.com>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>
|
|
Size is 1st arg, not second.
Signed-off-by: Dave Jones <davej@redhat.com>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>
|
|
Signed-off-by: Bhanu Prakash Gollapudi <bprakash@broadcom.com>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>
|
|
When SRR LS_ACC is dropped, the driver was not issuing ABTS for SRR when it
times out. Since the target received SRR, it was able to send the XFER_RDY and
the the original IO request completed successfully. In this condition ABTS was
not sent during bnx2fc_srr_compl(). Fix this by first checking for ELS timeout
and issue ABTS before checking if original IO request is complete.
Signed-off-by: Bhanu Prakash Gollapudi <bprakash@broadcom.com>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>
|
|
If the IO and the corresponding ABTS are not responded by a target, cleanup the
IO and issue explicit logout when ulp timer expires while waiting for ABTS to
complete. Wait for the session to be ready before returning to the SCSI layer.
If the session is not ready let the SCSI-ml escalate the error recovery.
Signed-off-by: Bhanu Prakash Gollapudi <bprakash@broadcom.com>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>
|
|
The call to complete() in st_scsi_execute_end() wakes up sleeping thread
in write_behind_check(), which frees the st_request, thus invalidating
the pointer to the associated bio structure, which is then passed to the
blk_rq_unmap_user(). Fix by storing pointer to bio structure into
temporary local variable.
This bug is present since at least linux-2.6.32.
CC: stable@kernel.org
Signed-off-by: Petr Uzel <petr.uzel@suse.cz>
Reported-by: Juergen Groß <juergen.gross@ts.fujitsu.com>
Reviewed-by: Jan Kara <jack@suse.cz>
Acked-by: Kai Mäkisara <kai.makisara@kolumbus.fi>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>
|
|
Make sure that SCSI device removal via scsi_remove_host() does finish
all pending SCSI commands. Currently that's not the case and hence
removal of a SCSI host during I/O can cause a deadlock. See also
"blkdev_issue_discard() hangs forever if underlying storage device is
removed" (http://bugzilla.kernel.org/show_bug.cgi?id=40472). See also
http://lkml.org/lkml/2011/8/27/6.
Signed-off-by: Bart Van Assche <bvanassche@acm.org>
Cc: <stable@kernel.org>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>
|
|
There is no reason to limit the SCSI disk namespace to sdXXX.
Add new error messages to sd_probe() in the unlikely event that either
ida_get_new() or sd_format_disk_name() fail.
Signed-off-by: Dave Kleikamp <dave.kleikamp@oracle.com>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>
|
|
Bump driver vesion to 10.100.00.00
Signed-off-by: Nagalakshmi Nandigama <nagalakshmi.nandigama@lsi.com>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>
|
|
The driver was setting the action to MPI2_CONFIG_ACTION_PAGE_READ_CURRENT,
which only returns active volumes. In order to get info on inactive volumes,
the driver needs to change the action to
MPI2_RAID_PGAD_FORM_GET_NEXT_CONFIGNUM, and traverse each config till the
iocstatus is MPI2_IOCSTATUS_CONFIG_INVALID_PAGE returned.
Added a change in the driver to remove the instance of
sas_device object when the driver returns "1" from the slave_configure callback.
Also fixed code to report the hot spares to the operating system with a /dev/sg
assigned.
Signed-off-by: Nagalakshmi Nandigama <nagalakshmi.nandigama@lsi.com>
Cc: stable@kernel.org
Signed-off-by: James Bottomley <JBottomley@Parallels.com>
|
|
complete while issued during creating a volume
This is due to the slave_configuration routine is getting called when
host reset is active, and config page reads are failing, and driver
attempts to added device with stale config data.
To fix the issue, added error checking in slave_configure to check
for configuration pages failing, and return "1" so the device is
not configured. The config pages are failing if raid volume is
configured while issuing a host reset, thus driver is reading stale
data and proceeding to attempt to add. The fix is to return error
so the volume is not configured.
Signed-off-by: Nagalakshmi Nandigama <nagalakshmi.nandigama@lsi.com>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>
|
|
reset context
This is due to driver reporting a device missing to the OS then the OS sending
a SYNC_CACHE request to driver while the IO queues are locked due to host reset.
To fix the issue, the driver will be waking up the port enable context
immediately when the driver receives the reply message, instead of waiting
on the hot plug worker threads.
Signed-off-by: Nagalakshmi Nandigama <nagalakshmi.nandigama@lsi.com>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>
|
|
sas_device_lock
Fix for dead lock occurring between host_lock and sas_device_lock.
The deadlock is between two spin locks, between the shost->host_lock
and driver ioc->sas_device_lock.
The fix is to rearrange the code in the FW/Driver device removal
handshake so the ioc->sas_device_lock is not occurring when the
shost->host_lock is taken.
[jejb: zero initialise sas_address to fix spurious compiler warning]
Signed-off-by: Nagalakshmi Nandigama <nagalakshmi.nandigama@lsi.com>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>
|
|
removed while host reset is active
The fix is in the driver-firmware handshake device removal code. We
need to read the controller ioc_state to see if controller is OPERATIONAL
prior to sending target reset and OP_REMOVE. Previously it was checking
the flag ioc->shost_recovery flag, which is always set when host reset is
active, thus preventing drives from getting properly deleted.
Signed-off-by: Nagalakshmi Nandigama <nagalakshmi.nandigama@lsi.com>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>
|
|
The fix is to inhibit the warning message in _scsih_get_sas_address
when the MPI2_IOCSTATUS_CONFIG_INVALID_PAGE ioc status is returned.
Signed-off-by: Nagalakshmi Nandigama <nagalakshmi.nandigama@lsi.com>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>
|
|
Fix for issue : While discovery is in progress, hot unplug and hot plug of
enclosure connected to the controller card is causing system to hang.
When a device is in the process of being detected at driver load time then
if it is removed, the device that is no longer present will not be added
to the list. So the code in _scsih_probe_sas() is rearranged as such so
the devices that failed to be detected are not added to the list.
Signed-off-by: Nagalakshmi Nandigama <nagalakshmi.nandigama@lsi.com>
Cc: stable@kernel.org
Signed-off-by: James Bottomley <JBottomley@Parallels.com>
|
|
New feature Fast Load Support.
(1)Asynchronous SCSI scanning: This will allow the drivers to scan
for devices in parallel while other device drivers are loading at
the same time. This will improve the amount of time it takes for the
OS to load.
(2) Reporting Devices while port enable is active: This feature will
allow devices to be reported to OS immediately while port enable is
active. The previous implementation waits for port enable to complete,
and then report devices. This feature is only enabled on IT firmware
configurations when there are no boot device configured in BIOS Configuration
Utility, else the driver will wait till port enable completes reporting
devices. For IR firmware, this feature is turned off. This feature is to
address large SAS topologies (>100 drives) when the boot OS is using onboard
SATA device, in other words, the boot devices is not
connected to our controller.
(3) Scanning for devices after diagnostic reset completes: A new routine
_scsih_scan_start is added. This will scan the expander pages, IR pages,
and sas device pages, then reporting new devices to SCSI Mid layer. It
seems the driver is not supporting adding devices while diagnostic reset
is active. Apparently this is due to the sanity checks on
ioc->shost_recovery flag throughout the context of kernel work thread FIFO,
and the mpt2sas_fw_work.
Signed-off-by: Nagalakshmi Nandigama <nagalakshmi.nandigama@lsi.com>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>
|
|
1)Added ProxyVF_ID field to Configuration Request message.
2)Added IO Unit Page 8, IO Unit Page 9,and IO Unit Page 10.
3)Added SASNotifyPrimitiveMasks field to IOC Page 7.
4)Added SAS NOTIFY Primitive event.
5)Added Temperature Threshold Event.
6)Added Host Message Event.
7)Added Send Host Message request and reply.
Signed-off-by: Nagalakshmi Nandigama <nagalakshmi.nandigama@lsi.com>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>
|
|
* git://git.kernel.org/pub/scm/linux/kernel/git/jejb/scsi-misc-2.6: (204 commits)
[SCSI] qla4xxx: export address/port of connection (fix udev disk names)
[SCSI] ipr: Fix BUG on adapter dump timeout
[SCSI] megaraid_sas: Fix instance access in megasas_reset_timer
[SCSI] hpsa: change confusing message to be more clear
[SCSI] iscsi class: fix vlan configuration
[SCSI] qla4xxx: fix data alignment and use nl helpers
[SCSI] iscsi class: fix link local mispelling
[SCSI] iscsi class: Replace iscsi_get_next_target_id with IDA
[SCSI] aacraid: use lower snprintf() limit
[SCSI] lpfc 8.3.27: Change driver version to 8.3.27
[SCSI] lpfc 8.3.27: T10 additions for SLI4
[SCSI] lpfc 8.3.27: Fix queue allocation failure recovery
[SCSI] lpfc 8.3.27: Change algorithm for getting physical port name
[SCSI] lpfc 8.3.27: Changed worst case mailbox timeout
[SCSI] lpfc 8.3.27: Miscellanous logic and interface fixes
[SCSI] megaraid_sas: Changelog and version update
[SCSI] megaraid_sas: Add driver workaround for PERC5/1068 kdump kernel panic
[SCSI] megaraid_sas: Add multiple MSI-X vector/multiple reply queue support
[SCSI] megaraid_sas: Add support for MegaRAID 9360/9380 12GB/s controllers
[SCSI] megaraid_sas: Clear FUSION_IN_RESET before enabling interrupts
...
|
|
* 'for-linus' of git://ceph.newdream.net/git/ceph-client:
libceph: fix double-free of page vector
ceph: fix 32-bit ino numbers
libceph: force resend of osd requests if we skip an osdmap
ceph: use kernel DNS resolver
ceph: fix ceph_monc_init memory leak
ceph: let the set_layout ioctl set single traits
Revert "ceph: don't truncate dirty pages in invalidate work thread"
ceph: replace leading spaces with tabs
libceph: warn on msg allocation failures
libceph: don't complain on msgpool alloc failures
libceph: always preallocate mon connection
libceph: create messenger with client
ceph: document ioctls
ceph: implement (optional) max read size
ceph: rename rsize -> rasize
ceph: make readpages fully async
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/tiwai/sound
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tiwai/sound: (549 commits)
ALSA: hda - Fix ADC input-amp handling for Cx20549 codec
ALSA: hda - Keep EAPD turned on for old Conexant chips
ALSA: hda/realtek - Fix missing volume controls with ALC260
ASoC: wm8940: Properly set codec->dapm.bias_level
ALSA: hda - Fix pin-config for ASUS W90V
ALSA: hda - Fix surround/CLFE headphone and speaker pins order
ALSA: hda - Fix typo
ALSA: Update the sound git tree URL
ALSA: HDA: Add new revision for ALC662
ASoC: max98095: Convert codec->hw_write to snd_soc_write
ASoC: keep pointer to resource so it can be freed
ASoC: sgtl5000: Fix wrong mask in some snd_soc_update_bits calls
ASoC: wm8996: Fix wrong mask for setting WM8996_AIF_CLOCKING_2
ASoC: da7210: Add support for line out and DAC
ASoC: da7210: Add support for DAPM
ALSA: hda/realtek - Fix DAC assignments of multiple speakers
ASoC: Use SGTL5000_LINREG_VDDD_MASK instead of hardcoded mask value
ASoC: Set sgtl5000->ldo in ldo_regulator_register
ASoC: wm8996: Use SND_SOC_DAPM_AIF_OUT for AIF2 Capture
ASoC: wm8994: Use SND_SOC_DAPM_AIF_OUT for AIF3 Capture
...
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/jbarnes/pci
* 'next-rebase' of git://git.kernel.org/pub/scm/linux/kernel/git/jbarnes/pci:
PCI: Clean-up MPS debug output
pci: Clamp pcie_set_readrq() when using "performance" settings
PCI: enable MPS "performance" setting to properly handle bridge MPS
PCI: Workaround for Intel MPS errata
PCI: Add support for PASID capability
PCI: Add implementation for PRI capability
PCI: Export ATS functions to modules
PCI: Move ATS implementation into own file
PCI / PM: Remove unnecessary error variable from acpi_dev_run_wake()
PCI hotplug: acpiphp: Prevent deadlock on PCI-to-PCI bridge remove
PCI / PM: Extend PME polling to all PCI devices
PCI quirk: mmc: Always check for lower base frequency quirk for Ricoh 1180:e823
PCI: Make pci_setup_bridge() non-static for use by arch code
x86: constify PCI raw ops structures
PCI: Add quirk for known incorrect MPSS
PCI: Add Solarflare vendor ID and SFC4000 device IDs
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/cjb/mmc
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/cjb/mmc: (83 commits)
mmc: fix compile error when CONFIG_BLOCK is not enabled
mmc: core: Cleanup eMMC4.5 conditionals
mmc: omap_hsmmc: if multiblock reads are broken, disable them
mmc: core: add workaround for controllers with broken multiblock reads
mmc: core: Prevent too long response times for suspend
mmc: recognise SDIO cards with SDIO_CCCR_REV 3.00
mmc: sd: Handle SD3.0 cards not supporting UHS-I bus speed mode
mmc: core: support HPI send command
mmc: core: Add cache control for eMMC4.5 device
mmc: core: Modify the timeout value for writing power class
mmc: core: new discard feature support at eMMC v4.5
mmc: core: mmc sanitize feature support for v4.5
mmc: dw_mmc: modify DATA register offset
mmc: sdhci-pci: add flag for devices that can support runtime PM
mmc: omap_hsmmc: ensure pbias configuration is always done
mmc: core: Add Power Off Notify Feature eMMC 4.5
mmc: sdhci-s3c: fix potential NULL dereference
mmc: replace printk with appropriate display macro
mmc: core: Add default timeout value for CMD6
mmc: sdhci-pci: add runtime pm support
...
|
|
http://ftp.arm.linux.org.uk/pub/linux/arm/kernel/git-cur/linux-2.6-arm
* 'devel-stable' of http://ftp.arm.linux.org.uk/pub/linux/arm/kernel/git-cur/linux-2.6-arm: (178 commits)
ARM: 7139/1: fix compilation with CONFIG_ARM_ATAG_DTB_COMPAT and large TEXT_OFFSET
ARM: gic, local timers: use the request_percpu_irq() interface
ARM: gic: consolidate PPI handling
ARM: switch from NO_MACH_MEMORY_H to NEED_MACH_MEMORY_H
ARM: mach-s5p64x0: remove mach/memory.h
ARM: mach-s3c64xx: remove mach/memory.h
ARM: plat-mxc: remove mach/memory.h
ARM: mach-prima2: remove mach/memory.h
ARM: mach-zynq: remove mach/memory.h
ARM: mach-bcmring: remove mach/memory.h
ARM: mach-davinci: remove mach/memory.h
ARM: mach-pxa: remove mach/memory.h
ARM: mach-ixp4xx: remove mach/memory.h
ARM: mach-h720x: remove mach/memory.h
ARM: mach-vt8500: remove mach/memory.h
ARM: mach-s5pc100: remove mach/memory.h
ARM: mach-tegra: remove mach/memory.h
ARM: plat-tcc: remove mach/memory.h
ARM: mach-mmp: remove mach/memory.h
ARM: mach-cns3xxx: remove mach/memory.h
...
Fix up mostly pretty trivial conflicts in:
- arch/arm/Kconfig
- arch/arm/include/asm/localtimer.h
- arch/arm/kernel/Makefile
- arch/arm/mach-shmobile/board-ap4evb.c
- arch/arm/mach-u300/core.c
- arch/arm/mm/dma-mapping.c
- arch/arm/mm/proc-v7.S
- arch/arm/plat-omap/Kconfig
largely due to some CONFIG option renaming (ie CONFIG_PM_SLEEP ->
CONFIG_ARM_CPU_SUSPEND for the arm-specific suspend code etc) and
addition of NEED_MACH_MEMORY_H next to HAVE_IDE.
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/hch/vfs-queue
* 'for-next' of git://git.kernel.org/pub/scm/linux/kernel/git/hch/vfs-queue: (21 commits)
leases: fix write-open/read-lease race
nfs: drop unnecessary locking in llseek
ext4: replace cut'n'pasted llseek code with generic_file_llseek_size
vfs: add generic_file_llseek_size
vfs: do (nearly) lockless generic_file_llseek
direct-io: merge direct_io_walker into __blockdev_direct_IO
direct-io: inline the complete submission path
direct-io: separate map_bh from dio
direct-io: use a slab cache for struct dio
direct-io: rearrange fields in dio/dio_submit to avoid holes
direct-io: fix a wrong comment
direct-io: separate fields only used in the submission path from struct dio
vfs: fix spinning prevention in prune_icache_sb
vfs: add a comment to inode_permission()
vfs: pass all mask flags check_acl and posix_acl_permission
vfs: add hex format for MAY_* flag values
vfs: indicate that the permission functions take all the MAY_* flags
compat: sync compat_stats with statfs.
vfs: add "device" tag to /proc/self/mountstats
cleanup: vfs: small comment fix for block_invalidatepage
...
Fix up trivial conflict in fs/gfs2/file.c (llseek changes)
|
|
* http://sucs.org/~rohan/git/gfs2-3.0-nmw: (24 commits)
GFS2: Move readahead of metadata during deallocation into its own function
GFS2: Remove two unused variables
GFS2: Misc fixes
GFS2: rewrite fallocate code to write blocks directly
GFS2: speed up delete/unlink performance for large files
GFS2: Fix off-by-one in gfs2_blk2rgrpd
GFS2: Clean up ->page_mkwrite
GFS2: Correctly set goal block after allocation
GFS2: Fix AIL flush issue during fsync
GFS2: Use cached rgrp in gfs2_rlist_add()
GFS2: Call do_strip() directly from recursive_scan()
GFS2: Remove obsolete assert
GFS2: Cache the most recently used resource group in the inode
GFS2: Make resource groups "append only" during life of fs
GFS2: Use rbtree for resource groups and clean up bitmap buffer ref count scheme
GFS2: Fix lseek after SEEK_DATA, SEEK_HOLE have been added
GFS2: Clean up gfs2_create
GFS2: Use ->dirty_inode()
GFS2: Fix bug trap and journaled data fsync
GFS2: Fix inode allocation error path
...
|
|
* '3.2-without-smb2' of git://git.samba.org/sfrench/cifs-2.6: (52 commits)
Fix build break when freezer not configured
Add definition for share encryption
CIFS: Make cifs_push_locks send as many locks at once as possible
CIFS: Send as many mandatory unlock ranges at once as possible
CIFS: Implement caching mechanism for posix brlocks
CIFS: Implement caching mechanism for mandatory brlocks
CIFS: Fix DFS handling in cifs_get_file_info
CIFS: Fix error handling in cifs_readv_complete
[CIFS] Fixup trivial checkpatch warning
[CIFS] Show nostrictsync and noperm mount options in /proc/mounts
cifs, freezer: add wait_event_freezekillable and have cifs use it
cifs: allow cifs_max_pending to be readable under /sys/module/cifs/parameters
cifs: tune bdi.ra_pages in accordance with the rsize
cifs: allow for larger rsize= options and change defaults
cifs: convert cifs_readpages to use async reads
cifs: add cifs_async_readv
cifs: fix protocol definition for READ_RSP
cifs: add a callback function to receive the rest of the frame
cifs: break out 3rd receive phase into separate function
cifs: find mid earlier in receive codepath
...
|
|
* 'for-linus' of git://oss.sgi.com/xfs/xfs: (69 commits)
xfs: add AIL pushing tracepoints
xfs: put in missed fix for merge problem
xfs: do not flush data workqueues in xfs_flush_buftarg
xfs: remove XFS_bflush
xfs: remove xfs_buf_target_name
xfs: use xfs_ioerror_alert in xfs_buf_iodone_callbacks
xfs: clean up xfs_ioerror_alert
xfs: clean up buffer allocation
xfs: remove buffers from the delwri list in xfs_buf_stale
xfs: remove XFS_BUF_STALE and XFS_BUF_SUPER_STALE
xfs: remove XFS_BUF_SET_VTYPE and XFS_BUF_SET_VTYPE_REF
xfs: remove XFS_BUF_FINISH_IOWAIT
xfs: remove xfs_get_buftarg_list
xfs: fix buffer flushing during unmount
xfs: optimize fsync on directories
xfs: reduce the number of log forces from tail pushing
xfs: Don't allocate new buffers on every call to _xfs_buf_find
xfs: simplify xfs_trans_ijoin* again
xfs: unlock the inode before log force in xfs_change_file_space
xfs: unlock the inode before log force in xfs_fs_nfs_commit_metadata
...
|
|
In setlease, we use i_writecount to decide whether we can give out a
read lease.
In open, we break leases before incrementing i_writecount.
There is therefore a window between the break lease and the i_writecount
increment when setlease could add a new read lease.
This would leave us with a simultaneous write open and read lease, which
shouldn't happen.
Signed-off-by: J. Bruce Fields <bfields@redhat.com>
Signed-off-by: Christoph Hellwig <hch@lst.de>
|
|
This makes NFS follow the standard generic_file_llseek locking scheme.
Cc: Trond.Myklebust@netapp.com
Signed-off-by: Andi Kleen <ak@linux.intel.com>
Signed-off-by: Christoph Hellwig <hch@lst.de>
|
|
This gives ext4 the benefits of unlocked llseek.
Cc: tytso@mit.edu
Signed-off-by: Andi Kleen <ak@linux.intel.com>
Signed-off-by: Christoph Hellwig <hch@lst.de>
|
|
Add a generic_file_llseek variant to the VFS that allows passing in
the maximum file size of the file system, instead of always
using maxbytes from the superblock.
This can be used to eliminate some cut'n'paste seek code in ext4.
Signed-off-by: Andi Kleen <ak@linux.intel.com>
Signed-off-by: Christoph Hellwig <hch@lst.de>
|
|
The i_mutex lock use of generic _file_llseek hurts. Independent processes
accessing the same file synchronize over a single lock, even though
they have no need for synchronization at all.
Under high utilization this can cause llseek to scale very poorly on larger
systems.
This patch does some rethinking of the llseek locking model:
First the 64bit f_pos is not necessarily atomic without locks
on 32bit systems. This can already cause races with read() today.
This was discussed on linux-kernel in the past and deemed acceptable.
The patch does not change that.
Let's look at the different seek variants:
SEEK_SET: Doesn't really need any locking.
If there's a race one writer wins, the other loses.
For 32bit the non atomic update races against read()
stay the same. Without a lock they can also happen
against write() now. The read() race was deemed
acceptable in past discussions, and I think if it's
ok for read it's ok for write too.
=> Don't need a lock.
SEEK_END: This behaves like SEEK_SET plus it reads
the maximum size too. Reading the maximum size would have the
32bit atomic problem. But luckily we already have a way to read
the maximum size without locking (i_size_read), so we
can just use that instead.
Without i_mutex there is no synchronization with write() anymore,
however since the write() update is atomic on 64bit it just behaves
like another racy SEEK_SET. On non atomic 32bit it's the same
as SEEK_SET.
=> Don't need a lock, but need to use i_size_read()
SEEK_CUR: This has a read-modify-write race window
on the same file. One could argue that any application
doing unsynchronized seeks on the same file is already broken.
But for the sake of not adding a regression here I'm
using the file->f_lock to synchronize this. Using this
lock is much better than the inode mutex because it doesn't
synchronize between processes.
=> So still need a lock, but can use a f_lock.
This patch implements this new scheme in generic_file_llseek.
I dropped generic_file_llseek_unlocked and changed all callers.
Signed-off-by: Andi Kleen <ak@linux.intel.com>
Signed-off-by: Christoph Hellwig <hch@lst.de>
|
|
This doesn't change anything for the compiler, but hch thought it would
make the code clearer.
I moved the reference counting into its own little inline.
Signed-off-by: Andi Kleen <ak@linux.intel.com>
Acked-by: Jeff Moyer <jmoyer@redhat.com>
Signed-off-by: Christoph Hellwig <hch@lst.de>
|
|
Add inlines to all the submission path functions. While this increases
code size it also gives gcc a lot of optimization opportunities
in this critical hotpath.
In particular -- together with some other changes -- this
allows gcc to get rid of the unnecessary clearing of
sdio at the beginning and optimize the messy parameter passing.
Any non inlining of a function which takes a sdio parameter
would break this optimization because they cannot be done if the
address of a structure is taken.
Note that benefits are only seen with CONFIG_OPTIMIZE_INLINING
and CONFIG_CC_OPTIMIZE_FOR_SIZE both set to off.
This gives about 2.2% improvement on a large database benchmark
with a high IOPS rate.
Signed-off-by: Andi Kleen <ak@linux.intel.com>
Signed-off-by: Christoph Hellwig <hch@lst.de>
|
|
Only a single b_private field in the map_bh buffer head is needed after
the submission path. Move map_bh separately to avoid storing
this information in the long term slab.
This avoids the weird 104 byte hole in struct dio_submit which also needed
to be memseted early.
Signed-off-by: Andi Kleen <ak@linux.intel.com>
Signed-off-by: Christoph Hellwig <hch@lst.de>
|
|
A direct slab call is slightly faster than kmalloc and can be better cached
per CPU. It also avoids rounding to the next kmalloc slab.
In addition this enforces cache line alignment for struct dio to avoid
any false sharing.
Signed-off-by: Andi Kleen <ak@linux.intel.com>
Acked-by: Jeff Moyer <jmoyer@redhat.com>
Signed-off-by: Christoph Hellwig <hch@lst.de>
|
|
Fix most problems reported by pahole.
There is still a weird 104 byte hole after map_bh. I'm not sure what
causes this.
Signed-off-by: Andi Kleen <ak@linux.intel.com>
Acked-by: Jeff Moyer <jmoyer@redhat.com>
Signed-off-by: Christoph Hellwig <hch@lst.de>
|
