| Age | Commit message (Collapse) | Author |
|---|
|
The current i2c hid driver does not support sending HID output reports using
the output register for devices which support receiving reports through this
method. This patch determines which method to use to send output reports based
on the value of wMaxOutputLength in the device's HID descriptor.
Signed-off-by: Andrew Duggan <aduggan@synaptics.com>
Reviewed-by: Benjamin Tissoires <benjamin.tissoires@redhat.com>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
|
|
Pull networking update from David Miller:
1) Fix dump iterator in nfnl_acct_dump() and ctnl_timeout_dump() to
dump all objects properly, from Pablo Neira Ayuso.
2) xt_TCPMSS must use the default MSS of 536 when no MSS TCP option is
present. Fix from Phil Oester.
3) qdisc_get_rtab() looks for an existing matching rate table and uses
that instead of creating a new one. However, it's key matching is
incomplete, it fails to check to make sure the ->data[] array is
identical too. Fix from Eric Dumazet.
4) ip_vs_dest_entry isn't fully initialized before copying back to
userspace, fix from Dan Carpenter.
5) Fix ubuf reference counting regression in vhost_net, from Jason
Wang.
6) When sock_diag dumps a socket filter back to userspace, we have to
translate it out of the kernel's internal representation first.
From Nicolas Dichtel.
7) davinci_mdio holds a spinlock while calling pm_runtime, which
sleeps. Fix from Sebastian Siewior.
8) Timeout check in sh_eth_check_reset is off by one, from Sergei
Shtylyov.
9) If sctp socket init fails, we can NULL deref during cleanup. Fix
from Daniel Borkmann.
10) netlink_mmap() does not propagate errors properly, from Patrick
McHardy.
11) Disable powersave and use minstrel by default in ath9k. From Sujith
Manoharan.
12) Fix a regression in that SOCK_ZEROCOPY is not set on tuntap sockets
which prevents vhost from being able to use zerocopy. From Jason
Wang.
13) Fix race between port lookup and TX path in team driver, from Jiri
Pirko.
14) Missing length checks in bluetooth L2CAP packet parsing, from Johan
Hedberg.
15) rtlwifi fails to connect to networking using any encryption method
other than WPA2. Fix from Larry Finger.
16) Fix iwlegacy build due to incorrect CONFIG_* ifdeffing for power
management stuff. From Yijing Wang.
* git://git.kernel.org/pub/scm/linux/kernel/git/davem/net: (35 commits)
b43: stop format string leaking into error msgs
ath9k: Use minstrel rate control by default
Revert "ath9k_hw: Update rx gain initval to improve rx sensitivity"
ath9k: Disable PowerSave by default
net: wireless: iwlegacy: fix build error for il_pm_ops
rtlwifi: Fix a false leak indication for PCI devices
wl12xx/wl18xx: scan all 5ghz channels
wl12xx: increase minimum singlerole firmware version required
wl12xx: fix minimum required firmware version for wl127x multirole
rtlwifi: rtl8192cu: Fix problem in connecting to WEP or WPA(1) networks
mwifiex: debugfs: Fix out of bounds array access
Bluetooth: Fix mgmt handling of power on failures
Bluetooth: Fix missing length checks for L2CAP signalling PDUs
Bluetooth: btmrvl: support Marvell Bluetooth device SD8897
Bluetooth: Fix checks for LE support on LE-only controllers
team: fix checks in team_get_first_port_txable_rcu()
team: move add to port list before port enablement
team: check return value of team_get_port_by_index_rcu() for NULL
tuntap: set SOCK_ZEROCOPY flag during open
netlink: fix error propagation in netlink_mmap()
...
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/jikos/hid
Pull input layer bugfix from Jiri Kosina:
"Memory leak regression fix from Benjamin Tissoires"
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/jikos/hid:
HID: multitouch: prevent memleak with the allocated name
|
|
Pull block layer fixes from Jens Axboe:
"Outside of bcache (which really isn't super big), these are all
few-liners. There are a few important fixes in here:
- Fix blk pm sleeping when holding the queue lock
- A small collection of bcache fixes that have been done and tested
since bcache was included in this merge window.
- A fix for a raid5 regression introduced with the bio changes.
- Two important fixes for mtip32xx, fixing an oops and potential data
corruption (or hang) due to wrong bio iteration on stacked devices."
* 'for-linus' of git://git.kernel.dk/linux-block:
scatterlist: sg_set_buf() argument must be in linear mapping
raid5: Initialize bi_vcnt
pktcdvd: silence static checker warning
block: remove refs to XD disks from documentation
blkpm: avoid sleep when holding queue lock
mtip32xx: Correctly handle bio->bi_idx != 0 conditions
mtip32xx: Fix NULL pointer dereference during module unload
bcache: Fix error handling in init code
bcache: clarify free/available/unused space
bcache: drop "select CLOSURES"
bcache: Fix incompatible pointer type warning
|
|
Merge misc fixes from Andrew Morton:
"Bunch of fixes and one little addition to math64.h"
* emailed patches from Andrew Morton <akpm@linux-foundation.org>: (27 commits)
include/linux/math64.h: add div64_ul()
mm: memcontrol: fix lockless reclaim hierarchy iterator
frontswap: fix incorrect zeroing and allocation size for frontswap_map
kernel/audit_tree.c:audit_add_tree_rule(): protect `rule' from kill_rules()
mm: migration: add migrate_entry_wait_huge()
ocfs2: add missing lockres put in dlm_mig_lockres_handler
mm/page_alloc.c: fix watermark check in __zone_watermark_ok()
drivers/misc/sgi-gru/grufile.c: fix info leak in gru_get_config_info()
aio: fix io_destroy() regression by using call_rcu()
rtc-at91rm9200: use shadow IMR on at91sam9x5
rtc-at91rm9200: add shadow interrupt mask
rtc-at91rm9200: refactor interrupt-register handling
rtc-at91rm9200: add configuration support
rtc-at91rm9200: add match-table compile guard
fs/ocfs2/namei.c: remove unecessary ERROR when removing non-empty directory
swap: avoid read_swap_cache_async() race to deadlock while waiting on discard I/O completion
drivers/rtc/rtc-twl.c: fix missing device_init_wakeup() when booted with device tree
cciss: fix broken mutex usage in ioctl
audit: wait_for_auditd() should use TASK_UNINTERRUPTIBLE
drivers/rtc/rtc-cmos.c: fix accidentally enabling rtc channel
...
|
|
There is div64_long() to handle the s64/long division, but no mocro do
u64/ul division. It is necessary in some scenarios, so add this
function.
[akpm@linux-foundation.org: coding-style fixes]
Signed-off-by: Alex Shi <alex.shi@intel.com>
Cc: Ingo Molnar <mingo@elte.hu>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
|
|
The lockless reclaim hierarchy iterator currently has a misplaced
barrier that can lead to use-after-free crashes.
The reclaim hierarchy iterator consist of a sequence count and a
position pointer that are read and written locklessly, with memory
barriers enforcing ordering.
The write side sets the position pointer first, then updates the
sequence count to "publish" the new position. Likewise, the read side
must read the sequence count first, then the position. If the sequence
count is up to date, it's guaranteed that the position is up to date as
well:
writer: reader:
iter->position = position if iter->sequence == expected:
smp_wmb() smp_rmb()
iter->sequence = sequence position = iter->position
However, the read side barrier is currently misplaced, which can lead to
dereferencing stale position pointers that no longer point to valid
memory. Fix this.
Signed-off-by: Johannes Weiner <hannes@cmpxchg.org>
Reported-by: Tejun Heo <tj@kernel.org>
Reviewed-by: Tejun Heo <tj@kernel.org>
Acked-by: Michal Hocko <mhocko@suse.cz>
Cc: KAMEZAWA Hiroyuki <kamezawa.hiroyu@jp.fujitsu.com>
Cc: Glauber Costa <glommer@parallels.com>
Cc: <stable@kernel.org> [3.10+]
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
|
|
The bitmap accessed by bitops must have enough size to hold the required
numbers of bits rounded up to a multiple of BITS_PER_LONG. And the
bitmap must not be zeroed by memset() if the number of bits cleared is
not a multiple of BITS_PER_LONG.
This fixes incorrect zeroing and allocation size for frontswap_map. The
incorrect zeroing part doesn't cause any problem because frontswap_map
is freed just after zeroing. But the wrongly calculated allocation size
may cause the problem.
For 32bit systems, the allocation size of frontswap_map is about twice
as large as required size. For 64bit systems, the allocation size is
smaller than requeired if the number of bits is not a multiple of
BITS_PER_LONG.
Signed-off-by: Akinobu Mita <akinobu.mita@gmail.com>
Cc: Konrad Rzeszutek Wilk <konrad.wilk@oracle.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
|
|
audit_add_tree_rule() must set 'rule->tree = NULL;' firstly, to protect
the rule itself freed in kill_rules().
The reason is when it is killed, the 'rule' itself may have already
released, we should not access it. one example: we add a rule to an
inode, just at the same time the other task is deleting this inode.
The work flow for adding a rule:
audit_receive() -> (need audit_cmd_mutex lock)
audit_receive_skb() ->
audit_receive_msg() ->
audit_receive_filter() ->
audit_add_rule() ->
audit_add_tree_rule() -> (need audit_filter_mutex lock)
...
unlock audit_filter_mutex
get_tree()
...
iterate_mounts() -> (iterate all related inodes)
tag_mount() ->
tag_trunk() ->
create_trunk() -> (assume it is 1st rule)
fsnotify_add_mark() ->
fsnotify_add_inode_mark() -> (add mark to inode->i_fsnotify_marks)
...
get_tree(); (each inode will get one)
...
lock audit_filter_mutex
The work flow for deleting an inode:
__destroy_inode() ->
fsnotify_inode_delete() ->
__fsnotify_inode_delete() ->
fsnotify_clear_marks_by_inode() -> (get mark from inode->i_fsnotify_marks)
fsnotify_destroy_mark() ->
fsnotify_destroy_mark_locked() ->
audit_tree_freeing_mark() ->
evict_chunk() ->
...
tree->goner = 1
...
kill_rules() -> (assume current->audit_context == NULL)
call_rcu() -> (rule->tree != NULL)
audit_free_rule_rcu() ->
audit_free_rule()
...
audit_schedule_prune() -> (assume current->audit_context == NULL)
kthread_run() -> (need audit_cmd_mutex and audit_filter_mutex lock)
prune_one() -> (delete it from prue_list)
put_tree(); (match the original get_tree above)
Signed-off-by: Chen Gang <gang.chen@asianux.com>
Cc: Eric Paris <eparis@redhat.com>
Cc: Al Viro <viro@zeniv.linux.org.uk>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
|
|
When we have a page fault for the address which is backed by a hugepage
under migration, the kernel can't wait correctly and do busy looping on
hugepage fault until the migration finishes. As a result, users who try
to kick hugepage migration (via soft offlining, for example) occasionally
experience long delay or soft lockup.
This is because pte_offset_map_lock() can't get a correct migration entry
or a correct page table lock for hugepage. This patch introduces
migration_entry_wait_huge() to solve this.
Signed-off-by: Naoya Horiguchi <n-horiguchi@ah.jp.nec.com>
Reviewed-by: Rik van Riel <riel@redhat.com>
Reviewed-by: Wanpeng Li <liwanp@linux.vnet.ibm.com>
Reviewed-by: Michal Hocko <mhocko@suse.cz>
Cc: Mel Gorman <mgorman@suse.de>
Cc: Andi Kleen <andi@firstfloor.org>
Cc: KOSAKI Motohiro <kosaki.motohiro@jp.fujitsu.com>
Cc: <stable@vger.kernel.org> [2.6.35+]
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
|
|
dlm_mig_lockres_handler() is missing a dlm_lockres_put() on an error path.
Signed-off-by: joyce <xuejiufei@huawei.com>
Reviewed-by: shencanquan <shencanquan@huawei.com>
Cc: Mark Fasheh <mfasheh@suse.com>
Cc: Joel Becker <jlbec@evilplan.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
|
|
The watermark check consists of two sub-checks. The first one is:
if (free_pages <= min + lowmem_reserve)
return false;
The check assures that there is minimal amount of RAM in the zone. If
CMA is used then the free_pages is reduced by the number of free pages
in CMA prior to the over-mentioned check.
if (!(alloc_flags & ALLOC_CMA))
free_pages -= zone_page_state(z, NR_FREE_CMA_PAGES);
This prevents the zone from being drained from pages available for
non-movable allocations.
The second check prevents the zone from getting too fragmented.
for (o = 0; o < order; o++) {
free_pages -= z->free_area[o].nr_free << o;
min >>= 1;
if (free_pages <= min)
return false;
}
The field z->free_area[o].nr_free is equal to the number of free pages
including free CMA pages. Therefore the CMA pages are subtracted twice.
This may cause a false positive fail of __zone_watermark_ok() if the CMA
area gets strongly fragmented. In such a case there are many 0-order
free pages located in CMA. Those pages are subtracted twice therefore
they will quickly drain free_pages during the check against
fragmentation. The test fails even though there are many free non-cma
pages in the zone.
This patch fixes this issue by subtracting CMA pages only for a purpose of
(free_pages <= min + lowmem_reserve) check.
Laura said:
We were observing allocation failures of higher order pages (order 5 =
128K typically) under tight memory conditions resulting in driver
failure. The output from the page allocation failure showed plenty of
free pages of the appropriate order/type/zone and mostly CMA pages in
the lower orders.
For full disclosure, we still observed some page allocation failures
even after applying the patch but the number was drastically reduced and
those failures were attributed to fragmentation/other system issues.
Signed-off-by: Tomasz Stanislawski <t.stanislaws@samsung.com>
Signed-off-by: Kyungmin Park <kyungmin.park@samsung.com>
Tested-by: Laura Abbott <lauraa@codeaurora.org>
Cc: Bartlomiej Zolnierkiewicz <b.zolnierkie@samsung.com>
Acked-by: Minchan Kim <minchan@kernel.org>
Cc: Mel Gorman <mel@csn.ul.ie>
Tested-by: Marek Szyprowski <m.szyprowski@samsung.com>
Cc: <stable@vger.kernel.org> [3.7+]
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
|
|
The "info.fill" array isn't initialized so it can leak uninitialized stack
information to user space.
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Acked-by: Robin Holt <holt@sgi.com>
Acked-by: Dimitri Sivanich <sivanich@sgi.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
|
|
There was a regression introduced by 36f5588905c1 ("aio: refcounting
cleanup"), reported by Jens Axboe - the refcounting cleanup switched to
using RCU in the shutdown path, but the synchronize_rcu() was done in
the context of the io_destroy() syscall greatly increasing the time it
could block.
This patch switches it to call_rcu() and makes shutdown asynchronous
(more asynchronous than it was originally; before the refcount changes
io_destroy() would still wait on pending kiocbs).
Note that there's a global quota on the max outstanding kiocbs, and that
quota must be manipulated synchronously; otherwise io_setup() could
return -EAGAIN when there isn't quota available, and userspace won't
have any way of waiting until shutdown of the old kioctxs has finished
(besides busy looping).
So we release our quota before kioctx shutdown has finished, which
should be fine since the quota never corresponded to anything real
anyways.
Signed-off-by: Kent Overstreet <koverstreet@google.com>
Cc: Zach Brown <zab@redhat.com>
Cc: Felipe Balbi <balbi@ti.com>
Cc: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Cc: Mark Fasheh <mfasheh@suse.com>
Cc: Joel Becker <jlbec@evilplan.org>
Cc: Rusty Russell <rusty@rustcorp.com.au>
Reported-by: Jens Axboe <axboe@kernel.dk>
Tested-by: Jens Axboe <axboe@kernel.dk>
Cc: Asai Thambi S P <asamymuthupa@micron.com>
Cc: Selvan Mani <smani@micron.com>
Cc: Sam Bradshaw <sbradshaw@micron.com>
Cc: Jeff Moyer <jmoyer@redhat.com>
Cc: Al Viro <viro@zeniv.linux.org.uk>
Signed-off-by: Benjamin LaHaise <bcrl@kvack.org>
Tested-by: Benjamin LaHaise <bcrl@kvack.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
|
|
Add support for the at91sam9x5-family which must use the shadow
interrupt mask due to a hardware issue (causing RTC_IMR to always be
zero).
Signed-off-by: Johan Hovold <jhovold@gmail.com>
Acked-by: Nicolas Ferre <nicolas.ferre@atmel.com>
Cc: Douglas Gilbert <dgilbert@interlog.com>
Cc: Jean-Christophe PLAGNIOL-VILLARD <plagnioj@jcrosoft.com>
Cc: Ludovic Desroches <ludovic.desroches@atmel.com>
Cc: Robert Nelson <Robert.Nelson@digikey.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
|
|
Add shadow interrupt-mask register which can be used on SoCs where the
actual hardware register is broken.
Note that some care needs to be taken to make sure the shadow mask
corresponds to the actual hardware state. The added overhead is not an
issue for the non-broken SoCs due to the relatively infrequent
interrupt-mask updates. We do, however, only use the shadow mask value
as a fall-back when it actually needed as there is still a theoretical
possibility that the mask is incorrect (see the code for details).
Signed-off-by: Johan Hovold <jhovold@gmail.com>
Acked-by: Nicolas Ferre <nicolas.ferre@atmel.com>
Cc: Douglas Gilbert <dgilbert@interlog.com>
Cc: Jean-Christophe PLAGNIOL-VILLARD <plagnioj@jcrosoft.com>
Cc: Ludovic Desroches <ludovic.desroches@atmel.com>
Cc: Robert Nelson <Robert.Nelson@digikey.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
|
|
Add accessors for the interrupt register.
This will allow us to easily add a shadow interrupt-mask register to use
on SoCs where the interrupt-mask register cannot be used.
Signed-off-by: Johan Hovold <jhovold@gmail.com>
Acked-by: Nicolas Ferre <nicolas.ferre@atmel.com>
Cc: Douglas Gilbert <dgilbert@interlog.com>
Cc: Jean-Christophe PLAGNIOL-VILLARD <plagnioj@jcrosoft.com>
Cc: Ludovic Desroches <ludovic.desroches@atmel.com>
Cc: Robert Nelson <Robert.Nelson@digikey.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
|
|
Add configuration support which can be used to implement SoC-specific
workarounds for broken hardware.
Signed-off-by: Johan Hovold <jhovold@gmail.com>
Acked-by: Nicolas Ferre <nicolas.ferre@atmel.com>
Cc: Douglas Gilbert <dgilbert@interlog.com>
Cc: Jean-Christophe PLAGNIOL-VILLARD <plagnioj@jcrosoft.com>
Cc: Ludovic Desroches <ludovic.desroches@atmel.com>
Cc: Robert Nelson <Robert.Nelson@digikey.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
|
|
The members of Atmel's at91sam9x5 family (9x5) have a broken RTC
interrupt mask register (AT91_RTC_IMR). It does not reflect enabled
interrupts but instead always returns zero.
The kernel's rtc-at91rm9200 driver handles the RTC for the 9x5 family.
Currently when the date/time is set, an interrupt is generated and this
driver neglects to handle the interrupt. The kernel complains about the
un-handled interrupt and disables it henceforth. This not only breaks
the RTC function, but since that interrupt is shared (Atmel's SYS
interrupt) then other things break as well (e.g. the debug port no
longer accepts characters).
Tested on the at91sam9g25. Bug confirmed by Atmel.
This patch (of 5):
Add missing match-table compile guard.
Signed-off-by: Johan Hovold <jhovold@gmail.com>
Acked-by: Nicolas Ferre <nicolas.ferre@atmel.com>
Cc: Douglas Gilbert <dgilbert@interlog.com>
Cc: Jean-Christophe PLAGNIOL-VILLARD <plagnioj@jcrosoft.com>
Cc: Ludovic Desroches <ludovic.desroches@atmel.com>
Cc: Robert Nelson <Robert.Nelson@digikey.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
|
|
While removing a non-empty directory, the kernel dumps a message:
(rmdir,21743,1):ocfs2_unlink:953 ERROR: status = -39
Suppress the error message from being printed in the dmesg so users
don't panic.
Signed-off-by: Goldwyn Rodrigues <rgoldwyn@suse.com>
Cc: Mark Fasheh <mfasheh@suse.com>
Cc: Joel Becker <jlbec@evilplan.org>
Acked-by: Sunil Mushran <sunil.mushran@gmail.com>
Reviewed-by: Jie Liu <jeff.liu@oracle.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
|
|
discard I/O completion
read_swap_cache_async() can race against get_swap_page(), and stumble
across a SWAP_HAS_CACHE entry in the swap map whose page wasn't brought
into the swapcache yet.
This transient swap_map state is expected to be transitory, but the
actual placement of discard at scan_swap_map() inserts a wait for I/O
completion thus making the thread at read_swap_cache_async() to loop
around its -EEXIST case, while the other end at get_swap_page() is
scheduled away at scan_swap_map(). This can leave the system deadlocked
if the I/O completion happens to be waiting on the CPU waitqueue where
read_swap_cache_async() is busy looping and !CONFIG_PREEMPT.
This patch introduces a cond_resched() call to make the aforementioned
read_swap_cache_async() busy loop condition to bail out when necessary,
thus avoiding the subtle race window.
Signed-off-by: Rafael Aquini <aquini@redhat.com>
Acked-by: Johannes Weiner <hannes@cmpxchg.org>
Acked-by: KOSAKI Motohiro <kosaki.motohiro@jp.fujitsu.com>
Acked-by: Hugh Dickins <hughd@google.com>
Cc: Shaohua Li <shli@kernel.org>
Cc: <stable@vger.kernel.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
|
|
device tree
When booted in legacy mode device_init_wakeup() gets called by
drivers/mfd/twl-core.c when the children are initialized. However, when
booted using device tree, the children are created with
of_platform_populate() instead add_children().
This means that the RTC driver will not have device_init_wakeup() set,
and we need to call it from the driver probe like RTC drivers typically
do.
Without this we cannot test PM wake-up events on omaps for cases where
there may not be any physical wake-up event.
Signed-off-by: Tony Lindgren <tony@atomide.com>
Reported-by: Kevin Hilman <khilman@linaro.org>
Cc: Alessandro Zummo <a.zummo@towertech.it>
Cc: Jingoo Han <jg1.han@samsung.com>
Cc: <stable@vger.kernel.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
|
|
If a new logical drive is added and the CCISS_REGNEWD ioctl is invoked
(as is normal with the Array Configuration Utility) the process will
hang as below. It attempts to acquire the same mutex twice, once in
do_ioctl() and once in cciss_unlocked_open(). The BKL was recursive,
the mutex isn't.
Linux version 3.10.0-rc2 (scameron@localhost.localdomain) (gcc version 4.4.7 20120313 (Red Hat 4.4.7-3) (GCC) ) #1 SMP Fri May 24 14:32:12 CDT 2013
[...]
acu D 0000000000000001 0 3246 3191 0x00000080
Call Trace:
schedule+0x29/0x70
schedule_preempt_disabled+0xe/0x10
__mutex_lock_slowpath+0x17b/0x220
mutex_lock+0x2b/0x50
cciss_unlocked_open+0x2f/0x110 [cciss]
__blkdev_get+0xd3/0x470
blkdev_get+0x5c/0x1e0
register_disk+0x182/0x1a0
add_disk+0x17c/0x310
cciss_add_disk+0x13a/0x170 [cciss]
cciss_update_drive_info+0x39b/0x480 [cciss]
rebuild_lun_table+0x258/0x370 [cciss]
cciss_ioctl+0x34f/0x470 [cciss]
do_ioctl+0x49/0x70 [cciss]
__blkdev_driver_ioctl+0x28/0x30
blkdev_ioctl+0x200/0x7b0
block_ioctl+0x3c/0x40
do_vfs_ioctl+0x89/0x350
SyS_ioctl+0xa1/0xb0
system_call_fastpath+0x16/0x1b
This mutex usage was added into the ioctl path when the big kernel lock
was removed. As it turns out, these paths are all thread safe anyway
(or can easily be made so) and we don't want ioctl() to be single
threaded in any case.
Signed-off-by: Stephen M. Cameron <scameron@beardog.cce.hp.com>
Cc: Jens Axboe <axboe@kernel.dk>
Cc: Mike Miller <mike.miller@hp.com>
Cc: <stable@vger.kernel.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
|
|
audit_log_start() does wait_for_auditd() in a loop until
audit_backlog_wait_time passes or audit_skb_queue has a room.
If signal_pending() is true this becomes a busy-wait loop, schedule() in
TASK_INTERRUPTIBLE won't block.
Thanks to Guy for fully investigating and explaining the problem.
(akpm: that'll cause the system to lock up on a non-preemptible
uniprocessor kernel)
(Guy: "Our customer was in fact running a uniprocessor machine, and they
reported a system hang.")
Signed-off-by: Oleg Nesterov <oleg@redhat.com>
Reported-by: Guy Streeter <streeter@redhat.com>
Cc: Eric Paris <eparis@redhat.com>
Cc: Al Viro <viro@zeniv.linux.org.uk>
Cc: <stable@vger.kernel.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
|
|
During resume, we call hpet_rtc_timer_init after masking an irq bit in
hpet. This will cause the call to hpet_disable_rtc_channel to be undone
if RTC_AIE is the only bit not masked.
Allowing the cmos interrupt handler to run before resuming caused some
issues where the timer for the alarm was not removed. This would cause
other, later timers to not be cleared, so utilities such as hwclock
would time out when waiting for the update interrupt.
[akpm@linux-foundation.org: coding-style tweak]
Signed-off-by: Derek Basehore <dbasehore@chromium.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
|
|
Use device_init_wakeup() instead of device_set_wakeup_capable() and move
it before rtc dev registering. This fixes alarmtimer not registered
when tps6586x rtc is the only wakeup compatible rtc in the system.
Signed-off-by: Dmitry Osipenko <digetx@gmail.com>
Cc: Laxman Dewangan <ldewangan@nvidia.com>
Cc: Jingoo Han <jg1.han@samsung.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
|
|
struct memcg_cache_params has a union. Different parts of this union
are used for root and non-root caches. A part with destroying work is
used only for non-root caches.
BUG: unable to handle kernel paging request at 0000000fffffffe0
IP: kmem_cache_alloc+0x41/0x1f0
Modules linked in: netlink_diag af_packet_diag udp_diag tcp_diag inet_diag unix_diag ip6table_filter ip6_tables i2c_piix4 virtio_net virtio_balloon microcode i2c_core pcspkr floppy
CPU: 0 PID: 1929 Comm: lt-vzctl Tainted: G D 3.10.0-rc1+ #2
Hardware name: Bochs Bochs, BIOS Bochs 01/01/2011
RIP: kmem_cache_alloc+0x41/0x1f0
Call Trace:
getname_flags.part.34+0x30/0x140
getname+0x38/0x60
do_sys_open+0xc5/0x1e0
SyS_open+0x22/0x30
system_call_fastpath+0x16/0x1b
Code: f4 53 48 83 ec 18 8b 05 8e 53 b7 00 4c 8b 4d 08 21 f0 a8 10 74 0d 4c 89 4d c0 e8 1b 76 4a 00 4c 8b 4d c0 e9 92 00 00 00 4d 89 f5 <4d> 8b 45 00 65 4c 03 04 25 48 cd 00 00 49 8b 50 08 4d 8b 38 49
RIP [<ffffffff8116b641>] kmem_cache_alloc+0x41/0x1f0
Signed-off-by: Andrey Vagin <avagin@openvz.org>
Cc: Konstantin Khlebnikov <khlebnikov@openvz.org>
Cc: Glauber Costa <glommer@parallels.com>
Cc: Johannes Weiner <hannes@cmpxchg.org>
Cc: Balbir Singh <bsingharora@gmail.com>
Cc: KAMEZAWA Hiroyuki <kamezawa.hiroyu@jp.fujitsu.com>
Reviewed-by: Michal Hocko <mhocko@suse.cz>
Cc: Li Zefan <lizefan@huawei.com>
Cc: <stable@vger.kernel.org> [3.9.x]
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
|
|
If an error occurs, for example an EIO in __ocfs2_prepare_orphan_dir,
ocfs2_prep_new_orphaned_file will release the inode_ac, then when the
caller of ocfs2_prep_new_orphaned_file gets a 0 return, it will refer to
a NULL ocfs2_alloc_context struct in the following functions. A kernel
panic happens.
Signed-off-by: "Xiaowei.Hu" <xiaowei.hu@oracle.com>
Reviewed-by: shencanquan <shencanquan@huawei.com>
Acked-by: Sunil Mushran <sunil.mushran@gmail.com>
Cc: Joe Jin <joe.jin@oracle.com>
Cc: Mark Fasheh <mfasheh@suse.com>
Cc: Joel Becker <jlbec@evilplan.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
|
|
'EXTRA_FLAGS=-W'.
For 'while' looping, need stop when 'nbytes == 0', or will cause issue.
('nbytes' is size_t which is always bigger or equal than zero).
The related warning: (with EXTRA_CFLAGS=-W)
lib/mpi/mpicoder.c:40:2: warning: comparison of unsigned expression >= 0 is always true [-Wtype-limits]
Signed-off-by: Chen Gang <gang.chen@asianux.com>
Cc: Rusty Russell <rusty@rustcorp.com.au>
Cc: David Howells <dhowells@redhat.com>
Cc: James Morris <james.l.morris@oracle.com>
Cc: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Acked-by: David Howells <dhowells@redhat.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
|
|
The dmesg_restrict sysctl currently covers the syslog method for access
dmesg, however /dev/kmsg isn't covered by the same protections. Most
people haven't noticed because util-linux dmesg(1) defaults to using the
syslog method for access in older versions. With util-linux dmesg(1)
defaults to reading directly from /dev/kmsg.
To fix /dev/kmsg, let's compare the existing interfaces and what they
allow:
- /proc/kmsg allows:
- open (SYSLOG_ACTION_OPEN) if CAP_SYSLOG since it uses a destructive
single-reader interface (SYSLOG_ACTION_READ).
- everything, after an open.
- syslog syscall allows:
- anything, if CAP_SYSLOG.
- SYSLOG_ACTION_READ_ALL and SYSLOG_ACTION_SIZE_BUFFER, if
dmesg_restrict==0.
- nothing else (EPERM).
The use-cases were:
- dmesg(1) needs to do non-destructive SYSLOG_ACTION_READ_ALLs.
- sysklog(1) needs to open /proc/kmsg, drop privs, and still issue the
destructive SYSLOG_ACTION_READs.
AIUI, dmesg(1) is moving to /dev/kmsg, and systemd-journald doesn't
clear the ring buffer.
Based on the comments in devkmsg_llseek, it sounds like actions besides
reading aren't going to be supported by /dev/kmsg (i.e.
SYSLOG_ACTION_CLEAR), so we have a strict subset of the non-destructive
syslog syscall actions.
To this end, move the check as Josh had done, but also rename the
constants to reflect their new uses (SYSLOG_FROM_CALL becomes
SYSLOG_FROM_READER, and SYSLOG_FROM_FILE becomes SYSLOG_FROM_PROC).
SYSLOG_FROM_READER allows non-destructive actions, and SYSLOG_FROM_PROC
allows destructive actions after a capabilities-constrained
SYSLOG_ACTION_OPEN check.
- /dev/kmsg allows:
- open if CAP_SYSLOG or dmesg_restrict==0
- reading/polling, after open
Addresses https://bugzilla.redhat.com/show_bug.cgi?id=903192
[akpm@linux-foundation.org: use pr_warn_once()]
Signed-off-by: Kees Cook <keescook@chromium.org>
Reported-by: Christian Kujau <lists@nerdbynature.de>
Tested-by: Josh Boyer <jwboyer@redhat.com>
Cc: Kay Sievers <kay@vrfy.org>
Cc: <stable@vger.kernel.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
|
|
We recently noticed that reboot of a 1024 cpu machine takes approx 16
minutes of just stopping the cpus. The slowdown was tracked to commit
f96972f2dc63 ("kernel/sys.c: call disable_nonboot_cpus() in
kernel_restart()").
The current implementation does all the work of hot removing the cpus
before halting the system. We are switching to just migrating to the
boot cpu and then continuing with shutdown/reboot.
This also has the effect of not breaking x86's command line parameter
for specifying the reboot cpu. Note, this code was shamelessly copied
from arch/x86/kernel/reboot.c with bits removed pertaining to the
reboot_cpu command line parameter.
Signed-off-by: Robin Holt <holt@sgi.com>
Tested-by: Shawn Guo <shawn.guo@linaro.org>
Cc: "Srivatsa S. Bhat" <srivatsa.bhat@linux.vnet.ibm.com>
Cc: H. Peter Anvin <hpa@zytor.com>
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: Ingo Molnar <mingo@elte.hu>
Cc: Russ Anderson <rja@sgi.com>
Cc: Robin Holt <holt@sgi.com>
Cc: Russell King <linux@arm.linux.org.uk>
Cc: Guan Xuetao <gxt@mprc.pku.edu.cn>
Cc: <stable@vger.kernel.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
|
|
There are instances in the kernel where we would like to disable CPU
hotplug (from sysfs) during some important operation. Today the freezer
code depends on this and the code to do it was kinda tailor-made for
that.
Restructure the code and make it generic enough to be useful for other
usecases too.
Signed-off-by: Srivatsa S. Bhat <srivatsa.bhat@linux.vnet.ibm.com>
Signed-off-by: Robin Holt <holt@sgi.com>
Cc: H. Peter Anvin <hpa@zytor.com>
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: Ingo Molnar <mingo@elte.hu>
Cc: Russ Anderson <rja@sgi.com>
Cc: Robin Holt <holt@sgi.com>
Cc: Russell King <linux@arm.linux.org.uk>
Cc: Guan Xuetao <gxt@mprc.pku.edu.cn>
Cc: Shawn Guo <shawn.guo@linaro.org>
Cc: <stable@vger.kernel.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
|
|
John W. Linville says:
====================
For now I have dropped the mac80211 tree from this request.
We are developing a little backlog of fixes and I would like to
avoid introducing any more uncertainty to this pull request for the
3.10 stream. All the other bits are the same as what was in the
2013-06-06 request, including the ath9k fixes intended to address
the problems observed by Linus w/ his Pixel, and a CVE fix for a
potential security issue in the b43 driver.
Regarding the wl12xx bits, Luca says:
"Here are three patches that I'd like to get into 3.10. Two of them, by
me, are related to the firmware version checks in our driver. Without
them, the firmwares fail to load. The other one, by Eliad, fixes a typo
bug in our 5GHz scanning code."
And as for the Bluetooth bits, Gustavo says:
"The following patches are important bug fixes for 3.10, plus the
support for a new device. We do have three fixes from Johan. The first
one is a fix to avoid LE-only devices to rely on the (inexistent)
extended features data. The second patch fixes length checks on
incoming L2CAP signalling PDUs so we can discard PDU whose size
doesn't match the one reported in the header. The last one fixes
the handling of power on failures, we now report proper errors to
mgmt when hci_dev_open()."
Along with that...
Larry Finger corrects an rtlwifi problem that caused some devices to
refuse to connect to non-WPA2 networks if the device had previously
assocated with a WPA2 network. He also adds a one-line fix to prevent
false reports from kmemleak.
Mark A. Greer fixes an out of bounds array access in mwifiex.
Felix Fietkau reverts an earlier ath9k initval patch that reduced rx
sensitivity in a number of ath9k devices with no corresponding benefit.
Kees Cook fixes a potential uid-0 to ring-0 escalation in b43
(CVE-2013-2852).
Sujith Manoharan turns-off powersave mode by default for ath9k, and
also defaults ath9k to use the minstrel_ht rate control algorithm.
Both of these are believed to contribute to greater stability/usability
of ath9k in real-world situations.
Yijing Wang fixes an iwlegacy build error for il_pm_ops if CONFIG_PM
is set but CONFIG_PM_SLEEP is not set.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Pull MIPS fixes from Ralf Baechle:
"Resurrect Alchemy platforms by invoking the WAIT instructions with
interrupts enabled. This still leaves the race condition between
testing TIF_NEED_RESCHED and the WAIT instruction for Alchemy
platforms which need a different fix than other MIPS platforms. But
at least it gets MIPS platforms flying again.
There are also fixes for two build errors (CONFIG_FTRACE=y with
CONFIG_DYNAMIC_FTRACE=n) and CONFIG_VIRTUALIZATION without CONFIG_KVM"
* 'upstream' of git://git.linux-mips.org/pub/scm/ralf/upstream-linus:
MIPS: ftrace: Add missing CONFIG_DYNAMIC_FTRACE
MIPS: include: mmu_context.h: Replace VIRTUALIZATION with KVM
MIPS: Alchemy: fix wait function
|
|
Pull drm fixes from Dave Airlie:
"Just some GMA500 memory leaks and i915 regression fix due to a
regression fix"
* 'drm-fixes' of git://people.freedesktop.org/~airlied/linux:
drm/i915: prefer VBT modes for SVDO-LVDS over EDID
drm/i915: Enable hotplug interrupts after querying hw capabilities.
drm/i915: Fix hotplug interrupt enabling for SDVOC
drm/gma500/cdv: Fix cursor gem obj referencing on cdv
drm/gma500/psb: Fix cursor gem obj referencing on psb
drm/gma500/cdv: Unpin framebuffer on crtc disable
drm/gma500/psb: Unpin framebuffer on crtc disable
drm/gma500: Add fb gtt offset to fb base
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/rostedt/linux-trace
Pull tracing fix from Steven Rostedt:
"Yoshihiro Yunomae fixed a regression in the output format when using
one of the counter clocks.
The new multibuffer code changed the trace_clock file to update the
trace instances tr->clock_id but the actual traces still used the
value from the obsolete global variable trace_clock_id"
* tag 'trace-fixes-v3.10-rc5' of git://git.kernel.org/pub/scm/linux/kernel/git/rostedt/linux-trace:
tracing: Fix outputting formats of x86-tsc and counter when use trace_clock
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/sage/ceph-client
Pull ceph fixes from Sage Weil:
"There is a pair of fixes for double-frees in the recent bundle for
3.10, a couple of fixes for long-standing bugs (sleep while atomic and
an endianness fix), and a locking fix that can be triggered when osds
are going down"
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/sage/ceph-client:
rbd: fix cleanup in rbd_add()
rbd: don't destroy ceph_opts in rbd_add()
ceph: ceph_pagelist_append might sleep while atomic
ceph: add cpu_to_le32() calls when encoding a reconnect capability
libceph: must hold mutex for reset_changed_osds()
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/linville/wireless into for-davem
|
|
The module parameter "fwpostfix" is userspace controllable, unfiltered,
and is used to define the firmware filename. b43_do_request_fw() populates
ctx->errors[] on error, containing the firmware filename. b43err()
parses its arguments as a format string. For systems with b43 hardware,
this could lead to a uid-0 to ring-0 escalation.
CVE-2013-2852
Signed-off-by: Kees Cook <keescook@chromium.org>
Cc: stable@vger.kernel.org
Signed-off-by: John W. Linville <linville@tuxdriver.com>
|
|
The ath9k rate control algorithm has various architectural
issues that make it a poor fit in scenarios like congested
environments etc.
An example: https://bugzilla.redhat.com/show_bug.cgi?id=927191
Change the default to minstrel which is more robust in such cases.
The ath9k RC code is left in the driver for now, maybe it can
be removed altogether later on.
Cc: stable@vger.kernel.org
Cc: Jouni Malinen <jouni@qca.qualcomm.com>
Cc: Linus Torvalds <torvalds@linux-foundation.org>
Signed-off-by: Sujith Manoharan <c_manoha@qca.qualcomm.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
|
|
This reverts commit 68d9e1fa24d9c7c2e527f49df8d18fb8cf0ec943
This change reduces rx sensitivity with no apparent extra benefit.
It looks like it was meant for testing in a specific scenario,
but it was never properly validated.
Cc: rmanohar@qca.qualcomm.com
Cc: stable@vger.kernel.org
Signed-off-by: Felix Fietkau <nbd@openwrt.org>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
|
|
Almost all the DMA issues which have plagued ath9k (in station mode)
for years are related to PS. Disabling PS usually "fixes" the user's
connection stablility. Reports of DMA problems are still trickling in
and are sitting in the kernel bugzilla. Until the PS code in ath9k is
given a thorough review, disbale it by default. The slight increase
in chip power consumption is a small price to pay for improved link
stability.
Cc: stable@vger.kernel.org
Signed-off-by: Sujith Manoharan <c_manoha@qca.qualcomm.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
|
|
Fix build error for il_pm_ops if CONFIG_PM is set
but CONFIG_PM_SLEEP is not set.
ERROR: "il_pm_ops" [drivers/net/wireless/iwlegacy/iwl4965.ko] undefined!
ERROR: "il_pm_ops" [drivers/net/wireless/iwlegacy/iwl3945.ko] undefined!
make[1]: *** [__modpost] Error 1
make: *** [modules] Error 2
Signed-off-by: Yijing Wang <wangyijing@huawei.com>
Cc: Stanislaw Gruszka <sgruszka@redhat.com>
Cc: "John W. Linville" <linville@tuxdriver.com>
Cc: netdev@vger.kernel.org
Cc: linux-wireless@vger.kernel.org
Cc: Jingoo Han <jg1.han@samsung.com>
Acked-by: Jingoo Han <jg1.han@samsung.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
|
|
This false leak indication is avoided with a no-leak annotation to kmemleak.
Signed-off-by: Larry Finger <Larry.Finger@lwfinger.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
|
|
Due to a typo, the current code copies only sizeof(cmd->channels_2)
bytes, which is smaller than the correct sizeof(cmd->channels_5)
size, resulting in a partial scan (some channels are skipped).
Signed-off-by: Eliad Peller <eliad@wizery.com>
Signed-off-by: Luciano Coelho <coelho@ti.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
|
|
The minimum firmware version required for singlerole after recent
driver changes is 6/7.3.10.0.133.
Reported-by: Tony Lindgren <tony@atomide.com>
Signed-off-by: Luciano Coelho <coelho@ti.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
|
|
There was a typo in commit 8675f9 (wlcore/wl12xx/wl18xx: verify
multi-role and single-role fw versions), which was causing the
multirole firmware for wl127x (WiLink6) to be rejected. The actual
minimum version needed for wl127x multirole is 6.5.7.0.42.
Reported-by: Levi Pearson <levipearson@gmail.com>
Reported-by: Michael Scott <hashcode0f@gmail.com>
Cc: stable@kernel.org # 3.9+
Signed-off-by: Luciano Coelho <coelho@ti.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
|
|
Driver rtl8192cu can connect to WPA2 networks, but fails for any other
encryption method. The cause is a failure to set the rate control data
blocks. These changes fix https://bugzilla.redhat.com/show_bug.cgi?id=952793
and https://bugzilla.redhat.com/show_bug.cgi?id=761525.
Signed-off-by: Larry Finger <Larry.Finger@lwfinger.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
|
|
When reading the contents of '/sys/kernel/debug/mwifiex/p2p0/info',
the following panic occurs:
$ cat /sys/kernel/debug/mwifiex/p2p0/info
Unable to handle kernel paging request at virtual address 74706164
pgd = de530000
[74706164] *pgd=00000000
Internal error: Oops: 5 [#1] SMP ARM
Modules linked in: phy_twl4030_usb omap2430 musb_hdrc mwifiex_sdio mwifiex
CPU: 0 PID: 1635 Comm: cat Not tainted 3.10.0-rc1-00010-g1268390 #1
task: de16b6c0 ti: de048000 task.ti: de048000
PC is at strnlen+0xc/0x4c
LR is at string+0x3c/0xf8
pc : [<c02c123c>] lr : [<c02c2d1c>] psr: a0000013
sp : de049e10 ip : c06efba0 fp : de6d2092
r10: bf01a260 r9 : ffffffff r8 : 74706164
r7 : 0000ffff r6 : ffffffff r5 : de6d209c r4 : 00000000
r3 : ff0a0004 r2 : 74706164 r1 : ffffffff r0 : 74706164
Flags: NzCv IRQs on FIQs on Mode SVC_32 ISA ARM Segment user
Control: 10c5387d Table: 9e530019 DAC: 00000015
Process cat (pid: 1635, stack limit = 0xde048240)
Stack: (0xde049e10 to 0xde04a000)
9e00: de6d2092 00000002 bf01a25e de6d209c
9e20: de049e80 c02c438c 0000000a ff0a0004 ffffffff 00000000 00000000 de049e48
9e40: 00000000 2192df6d ff0a0004 ffffffff 00000000 de6d2092 de049ef8 bef3cc00
9e60: de6b0000 dc358000 de6d2000 00000000 00000003 c02c45a4 bf01790c bf01a254
9e80: 74706164 bf018698 00000000 de59c3c0 de048000 de049f80 00001000 bef3cc00
9ea0: 00000008 00000000 00000000 00000000 00000000 00000000 00000000 00000000
9ec0: 00000000 00000000 00000000 00000000 00000000 00000000 00000000 00000000
9ee0: 00000000 00000000 00000000 00000001 00000000 00000000 6669776d 20786569
9f00: 20302e31 2e343128 392e3636 3231702e 00202933 00000000 00000003 c0294898
9f20: 00000000 00000000 00000000 00000000 de59c3c0 c0107c04 de554000 de59c3c0
9f40: 00001000 bef3cc00 de049f80 bef3cc00 de049f80 00000000 00000003 c0108a00
9f60: de048000 de59c3c0 00000000 00000000 de59c3c0 00001000 bef3cc00 c0108b60
9f80: 00000000 00000000 00001000 bef3cc00 00000003 00000003 c0014128 de048000
9fa0: 00000000 c0013f80 00001000 bef3cc00 00000003 bef3cc00 00001000 00000000
9fc0: 00001000 bef3cc00 00000003 00000003 00000001 00000001 00000001 00000003
9fe0: 00000000 bef3cbdc 00011984 b6f1127c 60000010 00000003 18dbdd2c 7f7bfffd
[<c02c123c>] (strnlen+0xc/0x4c) from [<c02c2d1c>] (string+0x3c/0xf8)
[<c02c2d1c>] (string+0x3c/0xf8) from [<c02c438c>] (vsnprintf+0x1e8/0x3e8)
[<c02c438c>] (vsnprintf+0x1e8/0x3e8) from [<c02c45a4>] (sprintf+0x18/0x24)
[<c02c45a4>] (sprintf+0x18/0x24) from [<bf01790c>] (mwifiex_info_read+0xfc/0x3e8 [mwifiex])
[<bf01790c>] (mwifiex_info_read+0xfc/0x3e8 [mwifiex]) from [<c0108a00>] (vfs_read+0xb0/0x144)
[<c0108a00>] (vfs_read+0xb0/0x144) from [<c0108b60>] (SyS_read+0x44/0x70)
[<c0108b60>] (SyS_read+0x44/0x70) from [<c0013f80>] (ret_fast_syscall+0x0/0x30)
Code: e12fff1e e3510000 e1a02000 0a00000d (e5d03000)
---[ end trace ca98273dc605a04f ]---
The panic is caused by the mwifiex_info_read() routine assuming that
there can only be four modes (0-3) which is an invalid assumption.
For example, when testing P2P, the mode is '8' (P2P_CLIENT) so the
code accesses data beyond the bounds of the bss_modes[] array which
causes the panic. Fix this by updating bss_modes[] to support the
current list of modes and adding a check to prevent the out-of-bounds
access from occuring in the future when more modes are added.
Signed-off-by: Mark A. Greer <mgreer@animalcreek.com>
Acked-by: Bing Zhao <bzhao@marvell.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
|
|
If hci_dev_open fails we need to ensure that the corresponding
mgmt_set_powered command gets an appropriate response. This patch fixes
the missing response by adding a new mgmt_set_powered_failed function
that's used to indicate a power on failure to mgmt. Since a situation
with the device being rfkilled may require special handling in user
space the patch uses a new dedicated mgmt status code for this.
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
Cc: stable@vger.kernel.org
Acked-by: Marcel Holtmann <marcel@holtmann.org>
Signed-off-by: Gustavo Padovan <gustavo.padovan@collabora.co.uk>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
|
