summaryrefslogtreecommitdiffstats
AgeCommit message (Collapse)Author
2009-10-27wl1271: Fix filter configurationJuuso Oikarinen
Fix the filter configuration to properly work with the two phase filter configuration (prepare_multicast/configure_filter.) Signed-off-by: Juuso Oikarinen <juuso.oikarinen@nokia.com> Reviewed-by: Luciano Coelho <luciano.coelho@nokia.com> Signed-off-by: Luciano Coelho <luciano.coelho@nokia.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
2009-10-27wl1271: make sure PS is disabled in PLTLuciano Coelho
We cannot be in PS mode when running PLT tests, so we need to make sure we're in active mode. Also, we need to clear up the rx_counter when we stop PLT, otherwise it could cause problems when entering PLT again. Signed-off-by: Luciano Coelho <luciano.coelho@nokia.com> Reviewed-by: Juuso Oikarinen <juuso.oikarinen@nokia.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
2009-10-27wl1271: Correct memory handling for FW bootJuuso Oikarinen
Several memory allocation related failure cases were not properly handled by the driver - the result was that in low memory conditions booting of a corrupted FW could be attempted - and user space would not get proper failure code. Signed-off-by: Juuso Oikarinen <juuso.oikarinen@nokia.com> Reviewed-by: Luciano Coelho <luciano.coelho@nokia.com> Signed-off-by: Luciano Coelho <luciano.coelho@nokia.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
2009-10-27wl1271: Remove unnecessary rx_descriptor memory allocationJuuso Oikarinen
Remove unnecessary RX descriptor memory allocation from the driver. The allocation was a remnant of the wl1251 driver. Signed-off-by: Juuso Oikarinen <juuso.oikarinen@nokia.com> Reviewed-by: Luciano Coelho <luciano.coelho@nokia.com> Signed-off-by: Luciano Coelho <luciano.coelho@nokia.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
2009-10-27wl1271: Support for IPv4 ARP filteringJuuso Oikarinen
Add support for IPv4 ARP filtering in the driver. This will dramatically reduce the number of unnecessary interrupts by the device in conqested networks. This patch is based on a similar patch to wl1251 by Janne Ylälehto. Cc: Janne Ylälehto <janne.ylalehto@nokia.com> Signed-off-by: Juuso Oikarinen <juuso.oikarinen@nokia.com> Reviewed-by: Luciano Coelho <luciano.coelho@nokia.com> Signed-off-by: Luciano Coelho <luciano.coelho@nokia.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
2009-10-27wl1271: Fix event handling mechanismJuuso Oikarinen
The event handling mechanism could miss events if multiple events would occur simultaneously. Fix event handling mechanism to process all events. Signed-off-by: Juuso Oikarinen <juuso.oikarinen@nokia.com> Reviewed-by: Luciano Coelho <luciano.coelho@nokia.com> Signed-off-by: Luciano Coelho <luciano.coelho@nokia.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
2009-10-27wl1271: Fix multicast list handlingJuuso Oikarinen
Fixes bugs in the multicast list handling: - Use atomic memory allocation in non-sleepable context - Increment address pointer when iterating list of MC addresses Signed-off-by: Juuso Oikarinen <juuso.oikarinen@nokia.com> Reviewed-by: Luciano Coelho <luciano.coelho@nokia.com> Signed-off-by: Luciano Coelho <luciano.coelho@nokia.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
2009-10-27wl1271: Checking of rx descriptor status fixedTeemu Paasikivi
Fixed checking of status of the received packet. On wl1251 status is in the flags field of the descriptor, on wl1271 there is a separate status field. Signed-off-by: Teemu Paasikivi <ext-teemu.3.paasikivi@nokia.com> Reviewed-by: Juuso Oikarinen <juuso.oikarinen@nokia.com> Signed-off-by: Luciano Coelho <luciano.coelho@nokia.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
2009-10-27wl1271: Added 5 GHz support to join and rxTeemu Paasikivi
Added support to assiociate and use connection on 5 GHz band (802.11a). Signed-off-by: Teemu Paasikivi <ext-teemu.3.paasikivi@nokia.com> Reviewed-by: Juuso Oikarinen <juuso.oikarinen@nokia.com> Signed-off-by: Luciano Coelho <luciano.coelho@nokia.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
2009-10-27wl1271: Added support to scan on 5 GHz bandTeemu Paasikivi
Added support to scan 802.11a access points on 5 GHz band when using wl1273 chip. Signed-off-by: Teemu Paasikivi <ext-teemu.3.paasikivi@nokia.com> Reviewed-by: Juuso Oikarinen <juuso.oikarinen@nokia.com> Signed-off-by: Luciano Coelho <luciano.coelho@nokia.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
2009-10-27wl1271: Scan only enabled channelsTeemu Paasikivi
Added checking of whether channel is enabled or disabled by mac80211 stack to scan. Disabled channels are not scanned. Signed-off-by: Teemu Paasikivi <ext-teemu.3.paasikivi@nokia.com> Reviewed-by: Juuso Oikarinen <juuso.oikarinen@nokia.com> Signed-off-by: Luciano Coelho <luciano.coelho@nokia.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
2009-10-27wl1271: Added 5 GHz parameters for wl1273Teemu Paasikivi
Added data rate and frequency tables for 5 GHz band channels, 5 GHz radio configration parameters and configuration option to enable 802.11 support. Signed-off-by: Teemu Paasikivi <ext-teemu.3.paasikivi@nokia.com> Reviewed-by: Juuso Oikarinen <juuso.oikarinen@nokia.com> Reviewed-by: Luciano Coelho <luciano.coelho@nokia.com> Signed-off-by: Luciano Coelho <luciano.coelho@nokia.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
2009-10-27wl1271: Remove busy-word checkingJuuso Oikarinen
Remove busy-word checking to work around an SPI bug. To reduce the chance of chipset-busy scenarios, increment the number of fixed busy words. Signed-off-by: Juuso Oikarinen <juuso.oikarinen@nokia.com> Reviewed-by: Luciano Coelho <luciano.coelho@nokia.com> Signed-off-by: Luciano Coelho <luciano.coelho@nokia.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
2009-10-27wl1271: Implement beacon early termination supportJuuso Oikarinen
Add support to enable beacon early termination in the firmware. Early Beacon termination is a feature which allows the radio to be turned off after TIM IE to save power. Signed-off-by: Juuso Oikarinen <juuso.oikarinen@nokia.com> Reviewed-by: Luciano Coelho <luciano.coelho@nokia.com> Signed-off-by: Luciano Coelho <luciano.coelho@nokia.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
2009-10-27wl1271: Fix IRQ enable handling on FW init failureJuuso Oikarinen
Disable IRQ's after FW initialization failure - originally this was not done in all cases, and it resulted in a kernel warning if firmware initialization was tried again without reboot. Signed-off-by: Juuso Oikarinen <juuso.oikarinen@nokia.com> Reviewed-by: Luciano Coelho <luciano.coelho@nokia.com> Signed-off-by: Luciano Coelho <luciano.coelho@nokia.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
2009-10-27wl1271: Move default FW config struct away from stackJuuso Oikarinen
Move the default FW config into a module global static variable, instead of being a stack variable. Signed-off-by: Juuso Oikarinen <juuso.oikarinen@nokia.com> Reviewed-by: Luciano Coelho <luciano.coelho@nokia.com> Signed-off-by: Luciano Coelho <luciano.coelho@nokia.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
2009-10-27wl1271: Add config structure for FW init parametersJuuso Oikarinen
Add a configuration structure for RX path parameters, and set default configuration values there. Signed-off-by: Juuso Oikarinen <juuso.oikarinen@nokia.com> Reviewed-by: Luciano Coelho <luciano.coelho@nokia.com> Signed-off-by: Luciano Coelho <luciano.coelho@nokia.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
2009-10-27wl1271: Add config structure for connection management parametersJuuso Oikarinen
Add a configuration structure for connection management parameters, and set default configuration values there. Signed-off-by: Juuso Oikarinen <juuso.oikarinen@nokia.com> Reviewed-by: Luciano Coelho <luciano.coelho@nokia.com> Signed-off-by: Luciano Coelho <luciano.coelho@nokia.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
2009-10-27wl1271: Add config structure for TX path parametersJuuso Oikarinen
Add a configuration structure for TX path parameters, and set defalt configuration values there. Signed-off-by: Juuso Oikarinen <juuso.oikarinen@nokia.com> Reviewed-by: Luciano Coelho <luciano.coelho@nokia.com> Signed-off-by: Luciano Coelho <luciano.coelho@nokia.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
2009-10-27wl1271: Add config structure for RX path parametersJuuso Oikarinen
Add a configuration structure for RX path parameters, and set default configuration values there. Signed-off-by: Juuso Oikarinen <juuso.oikarinen@nokia.com> Reviewed-by: Luciano Coelho <luciano.coelho@nokia.com> Signed-off-by: Luciano Coelho <luciano.coelho@nokia.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
2009-10-27wl1271: Add structure for firmware configuration valuesJuuso Oikarinen
In order to make the firmware configuration more manageable, collect hardcoded configuration values into one data structure, and set default values there. Add the SoftGemini BT/WLAN coex paramters into the config structure. Signed-off-by: Juuso Oikarinen <juuso.oikarinen@nokia.com> Reviewed-by: Luciano Coelho <luciano.coelho@nokia.com> Signed-off-by: Luciano Coelho <luciano.coelho@nokia.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
2009-10-27wl1271: Workaround for reference clock setting on boot.Juuso Oikarinen
If the 38.4MHz reference clock is configured to the firmware, it crashes on boot. Configuring an experimental 38.4MHz in XTAL mode allows the firmware to boot, and everything appears to work. Signed-off-by: Juuso Oikarinen <juuso.oikarinen@nokia.com> Reviewed-by: Luciano Coelho <luciano.coelho@nokia.com> Signed-off-by: Luciano Coelho <luciano.coelho@nokia.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
2009-10-27iwlwifi: use paged RxZhu Yi
This switches the iwlwifi driver to use paged skb from linear skb for Rx buffer. So that it relieves some Rx buffer allocation pressure for the memory subsystem. Currently iwlwifi (4K for 3945) requests 8K bytes for Rx buffer. Due to the trailing skb_shared_info in the skb->data, alloc_skb() will do the next order allocation, which is 16K bytes. This is suboptimal and more likely to fail when the system is under memory usage pressure. Switching to paged Rx skb lets us allocate the RXB directly by alloc_pages(), so that only order 1 allocation is required. It also adjusts the area spin_lock (with IRQ disabled) protected in the tasklet because tasklet guarentees to run only on one CPU and the new unprotected code can be preempted by the IRQ handler. This saves us from spawning another workqueue to make skb_linearize/__pskb_pull_tail happy (which cannot be called in hard irq context). Finally, mac80211 doesn't support paged Rx yet. So we linearize the skb for all the management frames and software decryption or defragmentation required data frames before handed to mac80211. For all the other frames, we __pskb_pull_tail 64 bytes in the linear area of the skb for mac80211 to handle them properly. Signed-off-by: Zhu Yi <yi.zhu@intel.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
2009-10-27wl1271: remove unnecessary joins and join only when the bssid changesLuciano Coelho
We were using the join command to change some settings when the stack asked us to do it. In many cases they were not needed (and could cause potential problems), so they were removed. In other cases there are ACX commands that can be used instead of using join to reconfigure. Signed-off-by: Luciano Coelho <luciano.coelho@nokia.com> Reviewed-by: Juuso Oikarinen <juuso.oikarinen@nokia.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
2009-10-27wl1271: use acx_rx_config instead of join when updating filtersLuciano Coelho
We shouldn't use a join command to change the filter settings while associated. The right way to do it is to use ACX_RX_CFG. Signed-off-by: Luciano Coelho <luciano.coelho@nokia.com> Reviewed-by: Juuso Oikarinen <juuso.oikarinen@nokia.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
2009-10-27wl1271: Update boot time configuration for the new firmwareJuuso Oikarinen
Update the magic values of the wl1271 boot time config according to the new reference driver. Signed-off-by: Juuso Oikarinen <juuso.oikarinen@nokia.com> Reviewed-by: Luciano Coelho <luciano.coelho@nokia.com> Signed-off-by: Luciano Coelho <luciano.coelho@nokia.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
2009-10-27wl1271: Remove outdated SPI functionsJuuso Oikarinen
With the change to the new firmware, there was a change to firmware memory partitioning. Along with that change, the translation of all partitions was unified, and separate functions for reg and mem access became unnecessary. Cleanup the unnecessary functions. Signed-off-by: Juuso Oikarinen <juuso.oikarinen@nokia.com> Reviewed-by: Luciano Coelho <luciano.coelho@nokia.com> Signed-off-by: Luciano Coelho <luciano.coelho@nokia.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
2009-10-27wl1271: Update TX path block calucation algoJuuso Oikarinen
Update the TX path block calculation algorithm based on TI reference. Signed-off-by: Juuso Oikarinen <juuso.oikarinen@nokia.com> Reviewed-by: Luciano Coelho <luciano.coelho@nokia.com> Signed-off-by: Luciano Coelho <luciano.coelho@nokia.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
2009-10-27wl1271: Enable smart reflexJuuso Oikarinen
Enable and configure smart reflex. This should have a reducing impact on power consumption. Signed-off-by: Juuso Oikarinen <juuso.oikarinen@nokia.com> Reviewed-by: Luciano Coelho <luciano.coelho@nokia.com> Signed-off-by: Luciano Coelho <luciano.coelho@nokia.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
2009-10-27wl1271: Enable ELPJuuso Oikarinen
The new firmware has fixed a firmware crash problem related to ELP entry. Enable ELP to conserve power. Signed-off-by: Juuso Oikarinen <juuso.oikarinen@nokia.com> Reviewed-by: Luciano Coelho <luciano.coelho@nokia.com> Signed-off-by: Luciano Coelho <luciano.coelho@nokia.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
2009-10-27wl1271: Update interrupt handling by removing an extra SPI readJuuso Oikarinen
Remove separate interrupt register reading from the interrupt handling routine. This will slightly improve interrupt performance. Signed-off-by: Juuso Oikarinen <juuso.oikarinen@nokia.com> Reviewed-by: Luciano Coelho <luciano.coelho@nokia.com> Signed-off-by: Luciano Coelho <luciano.coelho@nokia.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
2009-10-27wl1271: RefClk configurationJuuso Oikarinen
Updated RefClk configuration based on reference sources. Apparently this change will improve RF performance. Signed-off-by: Juuso Oikarinen <juuso.oikarinen@nokia.com> Reviewed-by: Luciano Coelho <luciano.coelho@nokia.com> Signed-off-by: Luciano Coelho <luciano.coelho@nokia.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
2009-10-27wl1271: Add top-register access functionsJuuso Oikarinen
Add top register access function. Signed-off-by: Juuso Oikarinen <juuso.oikarinen@nokia.com> Reviewed-by: Luciano Coelho <luciano.coelho@nokia.com> Signed-off-by: Luciano Coelho <luciano.coelho@nokia.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
2009-10-27wl1271: Remove RX workaroundJuuso Oikarinen
Remove RX workaround which is not needed with newer firmware revisions. This will reduce one SPI register transaction per RX packet. Signed-off-by: Juuso Oikarinen <juuso.oikarinen@nokia.com> Reviewed-by: Luciano Coelho <luciano.coelho@nokia.com> Signed-off-by: Luciano Coelho <luciano.coelho@nokia.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
2009-10-27wl1271: Update memory mapping for firmware revision 6.1.0.0.241Juuso Oikarinen
Update the memory regions and memory mapping to support firmware revision 6.1.0.0.241. Signed-off-by: Juuso Oikarinen <juuso.oikarinen@nokia.com> Reviewed-by: Luciano Coelho <luciano.coelho@nokia.com> Signed-off-by: Luciano Coelho <luciano.coelho@nokia.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
2009-10-27wl1271: enable HW_AVAILABLE interrupt to fix ELPLuciano Coelho
We need to listen to HW_AVAILABLE interrupts when using ELP with firmware revision 6.1.0.0.241. Add WL1271_ACX_INTR_HW_AVAILABLE to the interrupts that are enabled by default. Signed-off-by: Luciano Coelho <luciano.coelho@nokia.com> Reviewed-by: Juuso Oikarinen <juuso.oikarinen@nokia.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
2009-10-27wl1271: add workaround to avoid distortion due to excessive tx powerLuciano Coelho
We still don't have proper calibration for our devices, so we are using way too much power for TX, which causes a lot of distortion. This hack hardcodes the txpower to 7dBm. Signed-off-by: Luciano Coelho <luciano.coelho@nokia.com> Reviewed-by: Juuso Oikarinen <juuso.oikarinen@nokia.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
2009-10-27wl1271: workaround to send a disconnect before rejoiningLuciano Coelho
We don't get any indication from the stack when we have disassociated. In wl1271, it is important to send a CMD_DISCONNECT before joining again, because the firmware cleans some things up. So we check if we're already joined and disconnect if that's the case. Signed-off-by: Luciano Coelho <luciano.coelho@nokia.com> Reviewed-by: Juuso Oikarinen <juuso.oikarinen@nokia.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
2009-10-27wl1271: implement cmd_disconnectLuciano Coelho
This patch implements the CMD_DISCONNECT command, which should be sent to the firmware when we are disassociated. Signed-off-by: Luciano Coelho <luciano.coelho@nokia.com> Reviewed-by: Juuso Oikarinen <juuso.oikarinen@nokia.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
2009-10-27iwlwifi: update channel switch command APIWey-Yi Guy
Channel switch host command has different data structure for different devices. Adding additional structures to support 5000 and 6000 NICs. unlike 4965, starting with 5000 series, the tx power is managed by uCode, there is no tx power db information need to be passing from driver to uCode; but the space needs to be reserved to match uCode expection. 1000 NIC do not support channel switch operation since it is 'bgn' device, there is no need to have data structure defined for it. Signed-off-by: Wey-Yi Guy <wey-yi.w.guy@intel.com> Signed-off-by: Reinette Chatre <reinette.chatre@intel.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
2009-10-27iwl3945: rearrange the code.Abhijeet Kolekar
Rearrange the code and groups setting of retry_limit and data_retry_limits code together. Make 'data_retry_limit' setting similar to iwlwifi for better readability. Signed-off-by: Abhijeet Kolekar <abhijeet.kolekar@intel.com> Signed-off-by: Reinette Chatre <reinette.chatre@intel.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
2009-10-27iwlwifi/iwl3945: remove data_retry_limitAbhijeet Kolekar
Remove the ununsed variable data_retry_limit from priv. Signed-off-by: Abhijeet Kolekar <abhijeet.kolekar@intel.com> Signed-off-by: Reinette Chatre <reinette.chatre@intel.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
2009-10-27iwl3945: rename tx to tx_cmdAbhijeet Kolekar
Rename iwl3945_tx_cmd variable tx to tx_cmd for better readability. Signed-off-by: Abhijeet Kolekar <abhijeet.kolekar@intel.com> Signed-off-by: Reinette Chatre <reinette.chatre@intel.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
2009-10-27iwlwifi/iwl3945: unify rts_tx_cmd_flagAbhijeet Kolekar
3945 and 4965 share the functionality for setting RTS and CTS to the tx_cmd. Unify these functions and move the common functionality to core. Signed-off-by: Abhijeet Kolekar <abhijeet.kolekar@intel.com> Signed-off-by: Reinette Chatre <reinette.chatre@intel.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
2009-10-27iwlwifi: showing accumulative ucode statistics countersWey-Yi Guy
Adding accumulative statistics counters in iwlwifi driver. Statistics counters are reported by uCode every beacon interval; but can be reset by uCode when needed. The accumulative statistics counters is maintained by driver to keep track of the history of all the counters. Update the ucode stats files in debugfs to display both latest and accumulative counters. Signed-off-by: Wey-Yi Guy <wey-yi.w.guy@intel.com> Signed-off-by: Reinette Chatre <reinette.chatre@intel.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
2009-10-27iwlwifi: dynamic allocate tx queue structureWey-Yi Guy
Instead of always allocate the max number of tx queue structure, use dynamic allocation based on the number of queues in device configuration. With these changes, device does not have to allocate more memory than the h/w can support. Signed-off-by: Wey-Yi Guy <wey-yi.w.guy@intel.com> Signed-off-by: Reinette Chatre <reinette.chatre@intel.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
2009-10-27iwl3945: move iwl_power_initialize()Ben Cahill
iwl_power_initialize() initializes driver data (not device hardware), and does not need to execute more than once (when the driver initializes). Therefore, it does not belong in iwl3945_apm_init(), which initializes hardware, and may run more than once. Move it to iwl3945_pci_probe(), where it will run only once. This agrees with similar placement in iwl-agn.c's iwl_pci_probe(), although placement under "services" seemed more appropriate than under "mac80211". Signed-off-by: Ben Cahill <ben.m.cahill@intel.com> Signed-off-by: Reinette Chatre <reinette.chatre@intel.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
2009-10-27iwl3945: streamline iwl3945_rfkill_poll()Ben Cahill
iwl3945_rfkill_poll() has been silently calling wiphy_rfkill_set_hw_state() every 2 seconds, regardless of whether hardware RF KILL switch changed state. Call wiphy_rfkill_set_hw_state() only when RFKILL switch changes. Add IWL_DEBUG_RF_KILL log message and documentation. Signed-off-by: Ben Cahill <ben.m.cahill@intel.com> Signed-off-by: Reinette Chatre <reinette.chatre@intel.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
2009-10-27iwlwifi: fix userspace setting of sleep_level_overrideReinette Chatre
The sleep_level_override debugfs file is used by the user to request a static power index instead of the dynamic sleep values. Users are expected to provide value from 1 to 5 as an index or -1 to disable it. The problem at the moment is that users can also provide 0 to this file which, together with the value 1, is translated to index 1. This is confusing and even more so when users write 0 to sleep_level_override and then read 1 from it afterwards. Modify checking to treat 0 as invalid. Signed-off-by: Reinette Chatre <reinette.chatre@intel.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
2009-10-27iwlwifi: additional items in sensitivity range tableWey-Yi Guy
Add more items to sensitivity range table to avoid using hardcoded values. Initialize the table per device since unique per device information is required to perform sensitivity calibration. additional items in sensitivity range table: .barker_corr_th_min: Barker correlation threshold minimum .barker_corr_th_min_mrc: Barker correlation threshold minimum for MRC .nrg_th_cca: Energy threshold for Clear Channel Assessment Barker codes are a technique used in WLAN encoding for transmission. MRC is "Maximal Ratio Combining", a technique for optimally combining the signals from 2 or more receivers to achieve a better signal. Signed-off-by: Wey-Yi Guy <wey-yi.w.guy@intel.com> Signed-off-by: Reinette Chatre <reinette.chatre@intel.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
generated by cgit v1.2.3-70-g09d2 (git 2.46.0) at 2024-11-20 14:15:40 +0000