| Age | Commit message (Collapse) | Author |
|---|
|
The 57840 boards come in two flavours: 2 x 20G and 4 x 10G.
To better differentiate between the two flavours, a separate device ID
was assigned to each.
The silicon default value is still the currently supported 57840 device ID
(0x168d), and since a user can damage the nvram (e.g., 'ethtool -E')
the driver will still support this device ID to allow the user to amend the
nvram back into a supported configuration.
Notice this patch contains lines longer than 80 characters (strings).
Signed-off-by: Yuval Mintz <yuvalmin@broadcom.com>
Signed-off-by: Eilon Greenstein <eilong@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
In tcp_tw_remember_stamp we incorrectly checked tw
instead of tm, it can lead to oops if the cached entry is
not found.
tcpm_stamp was not updated in tcpm_check_stamp when
tcpm_suck_dst was called, move the update into tcpm_suck_dst,
so that we do not call it infinitely on every next cache hit
after TCP_METRICS_TIMEOUT.
Signed-off-by: Julian Anastasov <ja@ssi.bg>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
return value
Change niu_rbr_fill() to use unlikely() to check niu_rbr_add_page() return
value to be consistent with the rest of the checks after niu_rbr_add_page()
calls in this file.
Signed-off-by: Shuah Khan <shuah.khan@hp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Fix Neptune ethernet driver to check dma mapping error after map_page()
interface returns.
Signed-off-by: Shuah Khan <shuah.khan@hp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
In net/compat.c::put_cmsg_compat() we may assign 'data' the address of
either the 'ctv' or 'cts' local variables inside the 'if
(!COMPAT_USE_64BIT_TIME)' branch.
Those variables go out of scope at the end of the 'if' statement, so
when we use 'data' further down in 'copy_to_user(CMSG_COMPAT_DATA(cm),
data, cmlen - sizeof(struct compat_cmsghdr))' there's no telling what
it may be refering to - not good.
Fix the problem by simply giving 'ctv' and 'cts' function scope.
Signed-off-by: Jesper Juhl <jj@chaosbits.net>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
The ipv4 routing cache is non-deterministic, performance wise, and is
subject to reasonably easy to launch denial of service attacks.
The routing cache works great for well behaved traffic, and the world
was a much friendlier place when the tradeoffs that led to the routing
cache's design were considered.
What it boils down to is that the performance of the routing cache is
a product of the traffic patterns seen by a system rather than being a
product of the contents of the routing tables. The former of which is
controllable by external entitites.
Even for "well behaved" legitimate traffic, high volume sites can see
hit rates in the routing cache of only ~%10.
The general flow of this patch series is that first the routing cache
is removed. We build a completely new rtable entry every lookup
request.
Next we make some simplifications due to the fact that removing the
routing cache causes several members of struct rtable to become no
longer necessary.
Then we need to make some amends such that we can legally cache
pre-constructed routes in the FIB nexthops. Firstly, we need to
invalidate routes which are hit with nexthop exceptions. Secondly we
have to change the semantics of rt->rt_gateway such that zero means
that the destination is on-link and non-zero otherwise.
Now that the preparations are ready, we start caching precomputed
routes in the FIB nexthops. Output and input routes need different
kinds of care when determining if we can legally do such caching or
not. The details are in the commit log messages for those changes.
The patch series then winds down with some more struct rtable
simplifications and other tidy ups that remove unnecessary overhead.
On a SPARC-T3 output route lookups are ~876 cycles. Input route
lookups are ~1169 cycles with rpfilter disabled, and about ~1468
cycles with rpfilter enabled.
These measurements were taken with the kbench_mod test module in the
net_test_tools GIT tree:
git://git.kernel.org/pub/scm/linux/kernel/git/davem/net_test_tools.git
That GIT tree also includes a udpflood tester tool and stresses
route lookups on packet output.
For example, on the same SPARC-T3 system we can run:
time ./udpflood -l 10000000 10.2.2.11
with routing cache:
real 1m21.955s user 0m6.530s sys 1m15.390s
without routing cache:
real 1m31.678s user 0m6.520s sys 1m25.140s
Performance undoubtedly can easily be improved further.
For example fib_table_lookup() performs a lot of excessive
computations with all the masking and shifting, some of it
conditionalized to deal with edge cases.
Also, Eric's no-ref optimization for input route lookups can be
re-instated for the FIB nexthop caching code path. I would be really
pleased if someone would work on that.
In fact anyone suitable motivated can just fire up perf on the loading
of the test net_test_tools benchmark kernel module. I spend much of
my time going:
bash# perf record insmod ./kbench_mod.ko dst=172.30.42.22 src=74.128.0.1 iif=2
bash# perf report
Thanks to helpful feedback from Joe Perches, Eric Dumazet, Ben
Hutchings, and others.
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Add pm_runtime support to the TI Davinci EMAC driver.
CC: Sekhar Nori <nsekhar@ti.com>
CC: Kevin Hilman <khilman@ti.com>
Signed-off-by: Mark A. Greer <mgreer@animalcreek.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
The '#include <mach/mux.h>' line in davinci_emac.c
causes a compile error because that header file
isn't found. It turns out that the #include isn't
needed because the driver isn't (and shoudn't be)
touching the mux anyway, so remove it.
CC: Sekhar Nori <nsekhar@ti.com>
Signed-off-by: Mark A. Greer <mgreer@animalcreek.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
The section titled "Configuring Bonding for Maximum Throughput" is
actually section twelve not thirteen, and there are a couple of words
spelled incorrectly.
Signed-off-by: Rick Jones <rick.jones2@hp.com>
Reviewed-by: Nicolas de Pesloüan <nicolas.2p.debian@free.fr>
Signed-off-by: Jay Vosburgh <fubar@us.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Instead of updating the sk_cgrp_prioidx struct field on every send
this only updates the field when a task is moved via cgroup
infrastructure.
This allows sockets that may be used by a kernel worker thread
to be managed. For example in the iscsi case today a user can
put iscsid in a netprio cgroup and control traffic will be sent
with the correct sk_cgrp_prioidx value set but as soon as data
is sent the kernel worker thread isssues a send and sk_cgrp_prioidx
is updated with the kernel worker threads value which is the
default case.
It seems more correct to only update the field when the user
explicitly sets it via control group infrastructure. This allows
the users to manage sockets that may be used with other threads.
Signed-off-by: John Fastabend <john.r.fastabend@intel.com>
Acked-by: Neil Horman <nhorman@tuxdriver.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Let vhost-net utilize zero copy tx when used with tun.
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Export skb_copy_ubufs so that modules can orphan frags.
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
zero copy packets are normally sent to the outside
network, but bridging, tun etc might loop them
back to host networking stack. If this happens
destructors will never be called, so orphan
the frags immediately on receive.
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
tun xmit is actually receive of the internal tun
socket. Orphan the frags same as we do for normal rx path.
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Reduce code duplication a bit using the new helper.
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Many places do
if ((skb_shinfo(skb)->tx_flags & SKBTX_DEV_ZEROCOPY))
skb_copy_ubufs(skb, gfp_mask);
to copy and invoke frag destructors if necessary.
Add an inline helper for this.
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
This driver now offers software transmit time stamping, so it should
advertise that fact via ethtool. Compile tested only.
Signed-off-by: Richard Cochran <richardcochran@gmail.com>
Cc: Willem de Bruijn <willemb@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
This driver now offers software transmit time stamping, so it should
advertise that fact via ethtool. Compile tested only.
Signed-off-by: Richard Cochran <richardcochran@gmail.com>
Cc: Willem de Bruijn <willemb@google.com>
Cc: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Cc: e1000-devel@lists.sourceforge.net
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
This driver now offers software transmit time stamping, so it should
advertise that fact via ethtool. Compile tested only.
Signed-off-by: Richard Cochran <richardcochran@gmail.com>
Cc: Willem de Bruijn <willemb@google.com>
Cc: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Cc: e1000-devel@lists.sourceforge.net
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
This driver now offers software transmit time stamping, so it should
advertise that fact via ethtool. Compile tested only.
Signed-off-by: Richard Cochran <richardcochran@gmail.com>
Cc: Eilon Greenstein <eilong@broadcom.com>
Cc: Willem de Bruijn <willemb@google.com>
Acked-by: Eilon Greenstein <eilong@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Commit 76ff5cc91935c51fcf1a6a99ffa28b97a6e7a884
(rtnl: allow to specify number of rx and tx queues
on device creation) added a reference to the net_device
structure's 'num_rx_queues' member in
net/core/rtnetlink.c:rtnl_fill_ifinfo()
However, the definition for 'num_rx_queues' is surrounded
by an '#ifdef CONFIG_RPS' while the new reference to it is
not. This causes a compile error when CONFIG_RPS is not
defined.
Fix the compile error by surrounding the new reference to
'num_rx_queues' by an '#ifdef CONFIG_RPS'.
CC: Jiri Pirko <jiri@resnulli.us>
Signed-off-by: Mark A. Greer <mgreer@animalcreek.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/jkirsher/net-next
Jeff Kirsher says:
--------------------
This series contains updates to ixgbe and ixgbevf.
...
Akeem G. Abodunrin (1):
igb: reset PHY in the link_up process to recover PHY setting after
power down.
Alexander Duyck (8):
ixgbe: Drop probe_vf and merge functionality into ixgbe_enable_sriov
ixgbe: Change how we check for pre-existing and assigned VFs
ixgbevf: Add lock around mailbox ops to prevent simultaneous access
ixgbevf: Add support for PCI error handling
ixgbe: Fix handling of FDIR_HASH flag
ixgbe: Reduce Rx header size to what is actually used
ixgbe: Use num_tcs.pg_tcs as upper limit for TC when checking based
on UP
ixgbe: Use 1TC DCB instead of disabling DCB for MSI and legacy
interrupts
Don Skidmore (1):
ixgbe: add support for new 82599 device
Greg Rose (1):
ixgbevf: Fix namespace issue with ixgbe_write_eitr
John Fastabend (2):
ixgbe: fix RAR entry counting for generic and fdb_add()
ixgbe: remove extra unused queues in DCB + FCoE case
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/mst/vhost
|
|
Fix printk format warnings in drivers/net/wimax/i2400m:
drivers/net/wimax/i2400m/control.c: warning: format '%zu' expects argument of type 'size_t', but argument 4 has type 'ssize_t' [-Wformat]
drivers/net/wimax/i2400m/control.c: warning: format '%zu' expects argument of type 'size_t', but argument 5 has type 'ssize_t' [-Wformat]
drivers/net/wimax/i2400m/usb-fw.c: warning: format '%zu' expects argument of type 'size_t', but argument 4 has type 'ssize_t' [-Wformat]
I don't see these warnings on x86. The warnings that are quoted above
are from Geert's kernel build reports.
Signed-off-by: Randy Dunlap <rdunlap@xenotime.net>
Reported-by: Geert Uytterhoeven <geert@linux-m68k.org>
Cc: Inaky Perez-Gonzalez <inaky.perez-gonzalez@intel.com>
Cc: linux-wimax@intel.com
Cc: wimax@linuxwimax.org
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
I've seen several attempts recently made to do quick failover of sctp transports
by reducing various retransmit timers and counters. While its possible to
implement a faster failover on multihomed sctp associations, its not
particularly robust, in that it can lead to unneeded retransmits, as well as
false connection failures due to intermittent latency on a network.
Instead, lets implement the new ietf quick failover draft found here:
http://tools.ietf.org/html/draft-nishida-tsvwg-sctp-failover-05
This will let the sctp stack identify transports that have had a small number of
errors, and avoid using them quickly until their reliability can be
re-established. I've tested this out on two virt guests connected via multiple
isolated virt networks and believe its in compliance with the above draft and
works well.
Signed-off-by: Neil Horman <nhorman@tuxdriver.com>
CC: Vlad Yasevich <vyasevich@gmail.com>
CC: Sridhar Samudrala <sri@us.ibm.com>
CC: "David S. Miller" <davem@davemloft.net>
CC: linux-sctp@vger.kernel.org
CC: joe@perches.com
Acked-by: Vlad Yasevich <vyasevich@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Fix race condition in several network drivers when reading stats on 32bit
UP architectures. These drivers update their stats in a BH context and
therefore should use u64_stats_fetch_begin_bh/u64_stats_fetch_retry_bh
instead of u64_stats_fetch_begin/u64_stats_fetch_retry when reading the
stats.
Signed-off-by: Kevin Groeneveld <kgroeneveld@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Set unicast_sock uc_ttl to -1 so that we select the right ttl,
instead of sending packets with a 0 ttl.
Bug added in commit be9f4a44e7d4 (ipv4: tcp: remove per net tcp_sock)
Signed-off-by: Hiroaki SHIMODA <shimoda.hiroaki@gmail.com>
Signed-off-by: Eric Dumazet <edumazet@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
There was a previous patch to resolve issue with 82576 losing PHY setting
after PHY power down. However that previous implementation triggered speed
mismatch and occasional link lost. Now, this patch resolves both initial
PHY setting and speed mismatch issues.
Signed-off-by: Akeem G. Abodunrin <akeem.g.abodunrin@intel.com>
Tested-by: Jeff Pieper <jeffrey.e.pieper@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
|
|
This change makes it so that we can use 1TC DCB in the case of MSI and
legacy interrupts. The advantage to this is that it allows us to fully
support FCoE w/ DCB instead of having to drop to link flow control only
when using these interrupt modes.
Cc: John Fastabend <john.r.fastabend@intel.com>
Signed-off-by: Alexander Duyck <alexander.h.duyck@intel.com>
Tested-by: Ross Brattain <ross.b.brattain@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
|
|
This patch adds support for a new 82599 device that supports WoL.
Signed-off-by: Don Skidmore <donald.c.skidmore@intel.com>
Tested-by: Phil Schmitt <phillip.j.schmitt@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
|
|
With DCB and FCoE configured extra queues may be allocated and
never used. After this patch we calculate the max correctly.
Signed-off-by: John Fastabend <john.r.fastabend@intel.com>
Tested-by: Phil Schmitt <phillip.j.schmitt@intel.com>
Tested-by: Ross Brattain <ross.b.brattain@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
|
|
Do RAR entry accounting correctly so that errors are reported and
promisc mode is set correctly when the number of entries exceeds
the hardware limits.
This can happen with many macvlan devices attached to the PF or
by adding many fdb entries in SR-IOV modes.
Also this includes a small refactor to fdb_add() to avoid having so
many nested if/else statements after adding a check for the number
or RAR entries.
The max entries for the PF is currently 16 we allow 15 additional
entries to account for the defined MAC.
Signed-off-by: John Fastabend <john.r.fastabend@intel.com>
Tested-by: Phil Schmitt <phillip.j.schmitt@intel.com>
Tested-by: Ross Brattain <ross.b.brattain@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
|
|
This change makes it so the function ixgbe_dcb_get_tc_from_up will use the
num_tcs.pg_tcs to determine the starting value for determining a traffic
class based on a user priority. The main motivation for this change is to
address possible bad configurations in which more TCs worth of data are
populated then there are actual TCs. By limiting this value we can at
least make certain we are not providing a map with values that are out of
range.
As a result any user priorities that are setup in the configuration with a
traffic class mapping higher than what the hardware supports will be
reported as being on TC 0.
Signed-off-by: Alexander Duyck <alexander.h.duyck@intel.com>
Acked-by: Greg Rose <gregory.v.rose@intel.com>
Tested-by: Stephen Ko <stephen.s.ko@intel.com>
Tested-by: Ross Brattain <ross.b.brattain@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
|
|
The recent changes to netdev_alloc_skb actually make it so that the size of
the buffer now actually has a more direct input on the truesize. So in
order to make best use of the piece of a page we are allocated I am
reducing the IXGBE_RX_HDR_SIZE to 256 so that our truesize will be reduced
by 256 bytes as well.
This should result in performance improvements since the number of uses per
page should increase from 4 to 6 in the case of a 4K page. In addition we
should see socket performance improvements due to the truesize dropping
to less than 1K for buffers less than 256 bytes.
Cc: Eric Dumazet <edumazet@google.com>
Signed-off-by: Alexander Duyck <alexander.h.duyck@intel.com>
Tested-by: Phil Schmitt <phillip.j.schmitt@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
|
|
Make the function static to cleanup namespace.
Signed-off-by: Greg Rose <gregory.v.rose@intel.com>
Tested-by: Phil Schmitt <phillip.j.schmitt@intel.com>
Tested-by: Sibai Li <Sibai.li@intel.com
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
|
|
This change makes it so that we can use the atr_sample_rate to determine if
we are capable of supporting ATR. The advantage to this approach is that it
allows us to now determine the setting of the IXGBE_FLAG_FDIR_HASH_CAPABLE
based on the queueing scheme, instead of the queueing scheme being based on
the flag.
Using this approach there are essentially 5 conditions that must be checked
prior to trying to enable ATR:
1. Is SR-IOV disabled?
2. Are the number of TCs <= 1?
3. Is RSS queueing limit greater than 1?
4. Is atr_sample_rate set?
5. Is Flow Director perfect filtering disabled?
If any of these conditions are enabled they should disable ATR filtering.
Note that in the case of conditions 1 through 4 being met we will set
things up for ATR queueing, however if test 5 fails we will still leave the
queues allocated for use by perfect filters. The reason for this is to
allow for us to switch back and forth between ntuple and ATR without
needing to reallocate the descriptor rings.
Signed-off-by: Alexander Duyck <alexander.h.duyck@intel.com>
Tested-by: Phil Schmitt <phillip.j.schmitt@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
|
|
This change adds support for handling IO errors and slot resets.
Signed-off-by: Alexander Duyck <alexander.h.duyck@intel.com>
Signed-off-by: Greg Rose <gregory.v.rose@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
|
|
This change adds a spinlock around the mailbox accesses to prevent
simultaneous access to the mailboxes.
Signed-off-by: Alexander Duyck <alexander.h.duyck@intel.com>
Signed-off-by: Greg Rose <gregory.v.rose@intel.com>
Tested-by: Sibai Li <sibai.li@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
|
|
This patch does two things. First it drops the unnecessary work of
searching for enabled VFs when we first bring up the adapter and instead
just uses pci_num_vf to determine how many VFs are enabled on the adapter.
The second thing it does is drop the use of vfdev from the vf_data_storage
structure. Instead we just search the entire system for a VF that has us
as it's PF, and then if that VF is assigned we indicate that the VFs are
assigned. This allows us to still check for assigned VFs even if the
vfinfo allocation has failed, or vfinfo has been freed.
Signed-off-by: Alexander Duyck <alexander.h.duyck@intel.com>
Acked-by: Greg Rose <gregory.v.rose@intel.com>
Tested-by: Phil Schmitt <phillip.j.schmitt@intel.com>
Tested-by: Sibai Li <sibai.li@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
|
|
This is meant to fix a bug in which we were not checking for pre-existing
VFs if we were not setting the max_vfs value at driver load. What happens
now is that we always call ixgbe_enable_sriov and this checks for
pre-existing VFs ore requested VFs prior to deciding on no SR-IOV.
Signed-off-by: Alexander Duyck <alexander.h.duyck@intel.com>
Tested-by: Phil Schmitt <phillip.j.schmitt@intel.com>
Tested-by: Sibai Li <sibai.li@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
|
|
The vhost work queue allows processing to be done in vhost worker thread
context, which uses the owner process mm. Access to the vring and guest
memory is typically only possible from vhost worker context so it is
useful to allow work to be queued directly by users.
Currently vhost_net only uses the poll wrappers which do not expose the
work queue functions. However, for tcm_vhost (vhost_scsi) it will be
necessary to queue custom work.
Signed-off-by: Stefan Hajnoczi <stefanha@linux.vnet.ibm.com>
Cc: Zhi Yong Wu <wuzhy@cn.ibm.com>
Cc: Michael S. Tsirkin <mst@redhat.com>
Cc: Paolo Bonzini <pbonzini@redhat.com>
Signed-off-by: Nicholas Bellinger <nab@linux-iscsi.org>
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
|
|
In order for other vhost devices to use the VHOST_FEATURES bits the
vhost-net specific bits need to be moved to their own VHOST_NET_FEATURES
constant.
(Asias: Update drivers/vhost/test.c to use VHOST_NET_FEATURES)
Signed-off-by: Stefan Hajnoczi <stefanha@linux.vnet.ibm.com>
Cc: Zhi Yong Wu <wuzhy@cn.ibm.com>
Cc: Michael S. Tsirkin <mst@redhat.com>
Cc: Paolo Bonzini <pbonzini@redhat.com>
Cc: Asias He <asias@redhat.com>
Signed-off-by: Nicholas A. Bellinger <nab@risingtidesystems.com>
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
|
|
The replacement of spin_lock_irq/spin_unlock_irq pair in interrupt
handler by spin_lock_irqsave/spin_lock_irqrestore pair.
Found by Linux Driver Verification project (linuxtesting.org).
Signed-off-by: Denis Efremov <yefremov.denis@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/jesse/openvswitch
Jesse Gross says:
====================
A few bug fixes and small enhancements for net-next/3.6.
...
Ansis Atteka (1):
openvswitch: Do not send notification if ovs_vport_set_options() failed
Ben Pfaff (1):
openvswitch: Check gso_type for correct sk_buff in queue_gso_packets().
Jesse Gross (2):
openvswitch: Enable retrieval of TCP flags from IPv6 traffic.
openvswitch: Reset upper layer protocol info on internal devices.
Leo Alterman (1):
openvswitch: Fix typo in documentation.
Pravin B Shelar (1):
openvswitch: Check currect return value from skb_gso_segment()
Raju Subramanian (1):
openvswitch: Replace Nicira Networks.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
We were using a special key "0" for all loopback and point-to-point
device neigh lookups under ipv4, but we wouldn't use that special
key for the neigh creation.
So basically we'd make a new neigh at each and every lookup :-)
This special case to use only one neigh for these device types
is of dubious value, so just remove it entirely.
Reported-by: Eric Dumazet <eric.dumazet@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Signed-off-by: Leo Alterman <lalterman@nicira.com>
Signed-off-by: Jesse Gross <jesse@nicira.com>
|
|
At the point where it was used, skb_shinfo(skb)->gso_type referred to a
post-GSO sk_buff. Thus, it would always be 0. We want to know the pre-GSO
gso_type, so we need to obtain it before segmenting.
Before this change, the kernel would pass inconsistent data to userspace:
packets for UDP fragments with nonzero offset would be passed along with
flow keys that indicate a zero offset (that is, the flow key for "later"
fragments claimed to be "first" fragments). This inconsistency tended
to confuse Open vSwitch userspace, causing it to log messages about
"failed to flow_del" the flows with "later" fragments.
Signed-off-by: Ben Pfaff <blp@nicira.com>
Signed-off-by: Jesse Gross <jesse@nicira.com>
|
|
Fix return check typo.
Signed-off-by: Pravin B Shelar <pshelar@nicira.com>
Signed-off-by: Jesse Gross <jesse@nicira.com>
|
|
It's not really needed.
We only grabbed a reference to the fib_info for the sake of fib_info
local metrics.
However, fib_info objects are freed using RCU, as are therefore their
private metrics (if any).
We would have triggered a route cache flush if we eliminated a
reference to a fib_info object in the routing tables.
Therefore, any existing cached routes will first check and see that
they have been invalidated before an errant reference to these
metric values would occur.
Signed-off-by: David S. Miller <davem@davemloft.net>
|
