| Age | Commit message (Collapse) | Author |
|---|
|
Add support for allocating streams for USB 3.0 bulk endpoints. See
Documentation/usb/bulk-streams.txt for more information about how and why
you would use streams.
When an endpoint has streams enabled, instead of having one ring where all
transfers are enqueued to the hardware, it has several rings. The ring
dequeue pointer in the endpoint context is changed to point to a "Stream
Context Array". This is basically an array of pointers to transfer rings,
one for each stream ID that the driver wants to use.
The Stream Context Array size must be a power of two, and host controllers
can place a limit on the size of the array (4 to 2^16 entries). These
two facts make calculating the size of the Stream Context Array and the
number of entries actually used by the driver a bit tricky.
Besides the Stream Context Array and rings for all the stream IDs, we need
one more data structure. The xHCI hardware will not tell us which stream
ID a transfer event was for, but it will give us the slot ID, endpoint
index, and physical address for the TRB that caused the event. For every
endpoint on a device, add a radix tree to map physical TRB addresses to
virtual segments within a stream ring.
Keep track of whether an endpoint is transitioning to using streams, and
don't enqueue any URBs while that's taking place. Refuse to transition an
endpoint to streams if there are already URBs enqueued for that endpoint.
We need to make sure that freeing streams does not fail, since a driver's
disconnect() function may attempt to do this, and it cannot fail.
Pre-allocate the command structure used to issue the Configure Endpoint
command, and reserve space on the command ring for each stream endpoint.
This may be a bit overkill, but it is permissible for the driver to
allocate all streams in one call and free them in multiple calls. (It is
not advised, however, since it is a waste of resources and time.)
Even with the memory and ring room pre-allocated, freeing streams can
still fail because the xHC rejects the configure endpoint command. It is
valid (by the xHCI 0.96 spec) to return a "Bandwidth Error" or a "Resource
Error" for a configure endpoint command. We should never see a Bandwidth
Error, since bulk endpoints do not effect the reserved bandwidth. The
host controller can still return a Resource Error, but it's improbable
since the xHC would be going from a more resource-intensive configuration
(streams) to a less resource-intensive configuration (no streams).
If the xHC returns a Resource Error, the endpoint will be stuck with
streams and will be unusable for drivers. It's an unavoidable consequence
of broken host controller hardware.
Includes bug fixes from the original patch, contributed by
John Youn <John.Youn@synopsys.com> and Andy Green <AGreen@PLXTech.com>
Signed-off-by: Sarah Sharp <sarah.a.sharp@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
|
|
Bulk endpoint streams were added in the USB 3.0 specification. Streams
allow a device driver to overload a bulk endpoint so that multiple
transfers can be queued at once.
Add a new field, stream_id, to struct urb so that USB 3.0 drivers can
specify which stream they want the URB to be queued to.
Signed-off-by: Sarah Sharp <sarah.a.sharp@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
|
|
Allow the xHCI drivers (and any new USB 3.0 drivers) to parse the
SuperSpeed endpoint companion descriptor to find the maximum number of
bulk endpoint streams the endpoint supports. This is used to calculate
the maximum total number of streams the driver can allocate.
Signed-off-by: Sarah Sharp <sarah.a.sharp@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
|
|
Add ids for Qualcomm Gobi 2000 QDL and Modem modes. Gobi 2000 has a
single altsetting in QDL mode, so adapt code to handle that.
Firmware upload protocol is also slightly different, with an
additional firmware file. However, qcserial doesn't handle firmware
uploading.
Tested on Lenovo Thinkpad T510.
Signed-off-by: Anssi Hannula <anssi.hannula@gmail.com>
Signed-off-by: Matthew Garrett <mjg@redhat.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
|
|
Make qcserial use the generic USB wwan code. This should result in a
performance improvement.
Signed-off-by: Matthew Garrett <mjg@redhat.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
|
|
As this code was simply factored out of option, this is a simple
conversion.
Signed-off-by: Matthew Garrett <mjg@redhat.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
|
|
The generic USB serial code is ill-suited for high-speed USB wwan devices,
resulting in the option driver. However, other non-option devices may also
gain similar benefits from not using the generic code. Factorise out the
non-option specific code from the option driver and make it available to
other users.
Signed-off-by: Matthew Garrett <mjg@redhat.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
|
|
This patch (as1367) deprecates USB's power/level sysfs attribute in
favor of the power/control attribute provided by the runtime PM core.
The two attributes do the same thing.
It would be nice to replace power/level with a symlink to
power/control, but at the moment sysfs doesn't offer any way to do so.
Signed-off-by: Alan Stern <stern@rowland.harvard.edu>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
|
|
This patch (as1366) replaces the private routines
usb_enable_autosuspend() and usb_disable_autosuspend() with calls to
the standard pm_runtime_allow() and pm_runtime_forbid() functions in
the runtime PM framework. They do the same thing.
Signed-off-by: Alan Stern <stern@rowland.harvard.edu>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
|
|
This patch (as1364) avoids enabling remote wakeup by default on all
non-root-hub USB devices. Individual drivers or userspace will have
to enable it wherever it is needed, such as for keyboards or network
interfaces. Note: This affects only system sleep, not autosuspend.
External hubs will continue to relay wakeup requests received from
downstream through their upstream port, even when remote wakeup is not
enabled for the hub itself. Disabling remote wakeup on a hub merely
prevents it from generating wakeup requests in response to connect,
disconnect, and overcurrent events.
Signed-off-by: Alan Stern <stern@rowland.harvard.edu>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
|
|
This patch (as1362) adjusts the way the USB autosuspend routines
handle remote-wakeup settings. They aren't supposed to use
device_may_wakeup(); that test is intended only for system sleep, not
runtime power management. Instead the code checks to see if any
interface drivers need remote wakeup; if they do then it is enabled,
provided the device is capable of it.
Signed-off-by: Alan Stern <stern@rowland.harvard.edu>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
|
|
This patch (as1368) fixes a rather obscure bug in usbmon: When tracing
URBs sent by the scatter-gather library, it accesses the data buffers
while they are still mapped for DMA.
The solution is to move the mapping and unmapping out of the s-g
library and into the usual place in hcd.c. This requires the addition
of new URB flag bits to describe the kind of mapping needed, since we
have to call dma_map_sg() if the HCD supports native scatter-gather
operation and dma_map_page() if it doesn't. The nice thing about
having the new flags is that they simplify the testing for unmapping.
The patch removes the only caller of usb_buffer_[un]map_sg(), so those
functions are #if'ed out. A later patch will remove them entirely.
As a result of this change, urb->sg will be set in situations where
it wasn't set previously. Hence the xhci and whci drivers are
adjusted to test urb->num_sgs instead, which retains its original
meaning and is nonzero only when the HCD has to handle a scatterlist.
Finally, even when a submission error occurs we don't want to hand
URBs to usbmon before they are unmapped. The submission path is
rearranged so that map_urb_for_dma() is called only for non-root-hub
URBs and unmap_urb_for_dma() is called immediately after a submission
error. This simplifies the error handling.
Signed-off-by: Alan Stern <stern@rowland.harvard.edu>
CC: <stable@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
|
|
Endpoint addresses on pxa27x can be programmed as 1-15, but since
only three bits were being used to store the endpoint number it
was possible to overflow.
Signed-off-by: Matt Reimer <mreimer@sdgsystems.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
|
|
Rely on the global ULPI register definitions
Signed-off-by: Heikki Krogerus <ext-heikki.krogerus@nokia.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
|
|
Rely on the global ULPI register definitions
Signed-off-by: Heikki Krogerus <ext-heikki.krogerus@nokia.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
|
|
Definitions for registers defined by ULPI specification v1.1.
Signed-off-by: Heikki Krogerus <ext-heikki.krogerus@nokia.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
|
|
Mass Storage Function (MSF) used the same descriptors for each
usb_function instance (meaning usb_function::descriptors of different
functions pointed to the same static area (the same was true for
usb_function::hs_descriptors)).
This would leads to problems if MSF were used in several USB
configurations with different interface and/or endpoint numbers.
Descriptors for all configurations would have interface/endpoint
numbers overwritten by the values valid for the last configuration.
This patch adds code that copies the descriptors each time MSF is
added to USB configuration (that is for each usb_function).
Signed-off-by: Michal Nazarewicz <m.nazarewicz@samsung.com>
Cc: Kyungmin Park <kyungmin.park@samsung.com>
|
|
The composite framework allows gadgets with more than one function. This
can lead to situations where the configuration descriptor is larger than
the maximum of 512 bytes currently allowed by the composite framework.
This patch proposes to double that limit to 1024.
Signed-off-by: Robert Lukassen <robert.lukassen@tomtom.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
|
|
This adds helper functions for ULPI access, and implements
otg_io_access_ops for musb.
Signed-off-by: Heikki Krogerus <ext-heikki.krogerus@nokia.com>
Signed-off-by: Felipe Balbi <felipe.balbi@nokia.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
|
|
EXTVBUS programming is required by OMAP3EVM REV >=E to supply 500mA
power so adding a flag which can be used by musb driver to program
EXTVBUS.
Signed-off-by: Ajay Kumar Gupta <ajay.gupta@ti.com>
Signed-off-by: Felipe Balbi <felipe.balbi@nokia.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
|
|
Remove the unexistent CONFIG_USB_INVENTRA_MUSB_HAS_AHB_ID
option from our Makefile.
Problem reported by Sergei Shtylyov <sshtylyov@mvista.com>
Signed-off-by: Felipe Balbi <felipe.balbi@nokia.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
|
|
We don't need mach-types and hardware.h
Signed-off-by: Anand Gadiyar <gadiyar@ti.com>
Signed-off-by: Felipe Balbi <felipe.balbi@nokia.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
|
|
get_cpu_rev() is unused in this driver. It is probably legacy
code. So remove it.
Signed-off-by: Anand Gadiyar <gadiyar@ti.com>
Signed-off-by: Felipe Balbi <felipe.balbi@nokia.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
|
|
These functions do nothing and also are both unnecessarily 'extern'; actually,
musb_platform_resume() in not even called...
Signed-off-by: Sergei Shtylyov <sshtylyov@ru.mvista.com>
Signed-off-by: Felipe Balbi <felipe.balbi@nokia.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
|
|
This function is only called inside omap2430.c...
Signed-off-by: Sergei Shtylyov <sshtylyov@ru.mvista.com>
Signed-off-by: Felipe Balbi <felipe.balbi@nokia.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
|
|
This function does nothing...
Signed-off-by: Sergei Shtylyov <sshtylyov@ru.mvista.com>
Signed-off-by: Felipe Balbi <felipe.balbi@nokia.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
|
|
This function does nothing...
Signed-off-by: Sergei Shtylyov <sshtylyov@ru.mvista.com>
Signed-off-by: Felipe Balbi <felipe.balbi@nokia.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
|
|
Signed-off-by: Cliff Cai <cliff.cai@analog.com>
Signed-off-by: Mike Frysinger <vapier@gentoo.org>
Signed-off-by: Felipe Balbi <felipe.balbi@nokia.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
|
|
when we fail to probe(), we can call musb_exit_debugfs().
Allow that by removing section annotations.
Signed-off-by: Felipe Balbi <felipe.balbi@nokia.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
|
|
All unsuccessful (non-zero status) URBs were being dropped. After N_IN_URBs are
dropped you will no longer be able to receive data.
This patch resubmits unsuccessful URBs unless the status indicates that it should
be terminated. The statuses that indicate the URB should be terminated was
gathered from other similar drivers.
Signed-off-by: James Maki <jamescmaki@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
|
|
g_hid is a USB gadget driver implementing the Human Interface Device class
specification. The driver handles basic HID protocol handling in the
kernel, and allows userspace to read/write HID reports trough /dev/hidgX
character devices.
Signed-off-by: Fabien Chouteau <fabien.chouteau@barco.com>
Signed-off-by: Peter Korsgaard <peter.korsgaard@barco.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
|
|
Remove unnecessary comments stating function names at (some)
opening/closing braces.
Fix some whitespace issues.
Signed-off-by: Johan Hovold <jhovold@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
|
|
Generalise write buffer preparation.
This allows for drivers to manipulate (e.g. add headers) to bulk out
data before it is sent.
This adds a new function pointer to usb_serial_driver:
int (*prepare_write_buffer)(struct usb_serial_port *port,
void **dest, size_t size, const void *src, size_t count);
The function is generic and can be used with either kfifo-based or
multi-urb writes:
If *dest is NULL the implementation should allocate dest.
If src is NULL the implementation should use the port write fifo.
If not set, a generic implementation is used which simply uses memcpy or
kfifo_out.
Signed-off-by: Johan Hovold <jhovold@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
|
|
Use dynamic transfer buffer sizes since it is more efficient to let the
host controller do the partitioning to fit endpoint size. This way we
also do not use more than one urb per write request.
Replace max_in_flight_urbs with multi_urb_write flag in struct
usb_serial_driver to enable multi-urb writes.
Use MAX_TX_URBS=40 and a max buffer size of PAGE_SIZE to prevent DoS
attacks.
Signed-off-by: Johan Hovold <jhovold@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
|
|
Allow drivers to implement their own multi-urb write bulk callbacks as
we do for single urb writes.
Signed-off-by: Johan Hovold <jhovold@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
|
|
Use the generic kfifo-based write implementation rather than allowing up
to 4000 8 byte urbs in the host stack queues.
Cc: Jason Wessel <jason.wessel@windriver.com>
Signed-off-by: Johan Hovold <jhovold@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
|
|
Use usb_serial_generic_close to kill the read and write urbs and to
reset the write fifo.
Signed-off-by: Johan Hovold <jhovold@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
|
|
Replace custom fifo-based write implementation with the generic
kfifo-based one.
Signed-off-by: Johan Hovold <jhovold@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
|
|
Submit write urb if it is not already in use and we have buffered data.
Signed-off-by: Johan Hovold <jhovold@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
|
|
Clean up error messages on usb_submit_urb failure.
Remove debug message on zero-length writes.
Signed-off-by: Johan Hovold <jhovold@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
|
|
Switch to generic read implementation and use process_read_urb to do
device specific processing (handle line status).
Signed-off-by: Johan Hovold <jhovold@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
|
|
Allow drivers to use the generic throttle and unthrottle implementation.
This makes sense for drivers using the generic read functionality.
Note that drivers need to set these explicitly in order to enable them
(i.e., we do not set them at port probe if not defined).
Signed-off-by: Johan Hovold <jhovold@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
|
|
Use generic read implementation and use process_read_urb to do device
specific processing (handle line status).
Signed-off-by: Johan Hovold <jhovold@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
|
|
Add process_read_urb to usb_serial_driver so that a driver can rely on
the generic read (and throttle) mechanism but still do device specific
processing of incoming data (such as adding tty_flags before pushing to
line discipline).
The default generic implementation handles sysrq for consoles but
otherwise simply pushes to tty.
Signed-off-by: Johan Hovold <jhovold@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
|
|
Always process and flush read urb, but only resubmit when not throttled.
The new tty-layer supply plenty of slack so there is really no need to
cache and delay processing of a single urb while throttled.
Note that unthrottle now submits using GFP_KERNEL as we are not in
atomic context (so there is no need to save irq state either).
Note also that the process_read_urb function could be added to
usb_serial_driver should any driver need to do any device specific
processing.
Signed-off-by: Johan Hovold <jhovold@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
|
|
There is no need to initialise the read urb as this is done at port
probe.
Signed-off-by: Johan Hovold <jhovold@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
|
|
The generic read and write bulk urbs are initialised when allocated in
usb_serial_probe. The only field that needs to be updated after that is
the transfer_buffer_length of the write urb.
Signed-off-by: Johan Hovold <jhovold@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
|
|
Use the already exported function for submitting the read urb associated
with a usb_serial_port.
Make sure it returns the result of usb_submit_urb and rename to the
more descriptive usb_serial_generic_submit_read_urb.
Signed-off-by: Johan Hovold <jhovold@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
|
|
Export usb_serial_generic_close so that drivers can easily kill the read
and write urb and make sure that the write fifo is reset.
Signed-off-by: Johan Hovold <jhovold@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
|
|
Make sure fifo is emptied on close.
Signed-off-by: Johan Hovold <jhovold@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
|
