| Age | Commit message (Collapse) | Author |
|---|
|
Make use of INTC_IRQ_PINS_16() for INTCA on sh7367.
Signed-off-by: Magnus Damm <damm@opensource.se>
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
|
|
This patch adds support for sh73a0 GPIO IRQs by making use
of the PFC GPIO IRQ feature. Only IRQ pins are supported
at this time. In the future when PINT interrupts also are
supported properly we can easily extend the table with such
information. Also, the sh73a0 is currently making use of
the GIC for external interrupt which is rather unflexible
when it comes to triggering configuration at this point.
Signed-off-by: Magnus Damm <damm@opensource.se>
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
|
|
Always use CS0 shadow area for NOR flash instead of regular CS0
memory area on ap4evb.
When booting from CS0 NOR Flash the regular CS0 memory area is
available, but when booting via USB the MASK ROM gets mapped to
0x0 which gets in the way for the NOR Flash. Always using CS0
shadow area works well for both NOR Flash boot and USB boot.
Signed-off-by: Bastian Hecht <hechtb@gmail.com>
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
|
|
Always use CS0 shadow area for NOR flash instead of regular CS0
memory area on Mackerel.
When booting from CS0 NOR Flash the regular CS0 memory area is
available, but when booting via USB the MASK ROM gets mapped to
0x0 which gets in the way for the NOR Flash. Always using CS0
shadow area works well for both NOR Flash boot and USB boot.
Signed-off-by: Magnus Damm <damm@opensource.se>
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
|
|
Enable IRQ_TYPE_EDGE_BOTH on all R/SH-Mobile ARM SoCs.
This hardware feature is supported by sh7367, sh7377,
sh7372 and sh73a0.
Signed-off-by: Magnus Damm <damm@opensource.se>
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
|
|
Add INTC_IRQ_PINS_16() and INTC_IRQ_PINS_32() to mach/intc.h.
These macros define 16 or 32 external IRQ pins on a certain
memory base address. Can be used with INTCA or INTCS.
Signed-off-by: Magnus Damm <damm@opensource.se>
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
|
|
This provides a clk_rate_mult_range_round() helper for use by some of the
CPG PLL ranged multipliers, following the same approach as used by the
div ranges.
Signed-off-by: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/mchehab/linux-media
* 'v4l_for_linus' of git://git.kernel.org/pub/scm/linux/kernel/git/mchehab/linux-media: (144 commits)
[media] saa7134.h: Suppress compiler warnings when CONFIG_VIDEO_SAA7134_RC is not set
[media] it913x [VER 1.07] Support for single ITE 9135 devices
[media] Support for Terratec G1
[media] cx25821: off by one in cx25821_vidioc_s_input()
[media] media: tea5764: reconcile Kconfig symbol and macro
[media] omap_vout: Add poll() support
[media] omap3isp: preview: Add crop support on the sink pad
[media] omap3isp: preview: Rename min/max input/output sizes defines
[media] omap3isp: preview: Remove horizontal averager support
[media] omap3isp: Report the ISP revision through the media controller API
[media] omap3isp: ccdc: remove redundant operation
[media] omap3isp: Fix memory leaks in initialization error paths
[media] omap3isp: Add missing mutex_destroy() calls
[media] omap3isp: Move *_init_entities() functions to the init/cleanup section
[media] omap3isp: Move media_entity_cleanup() from unregister() to cleanup()
[media] MFC: Change MFC firmware binary name
[media] vb2: add vb2_get_unmapped_area in vb2 core
[media] v4l: Add v4l2 subdev driver for S5K6AAFX sensor
[media] v4l: Add AUTO option for the V4L2_CID_POWER_LINE_FREQUENCY control
[media] media: ov6650: stylistic improvements
...
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/jdelvare/staging
* 'hwmon-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/jdelvare/staging:
hwmon: (w83627ehf) Add support for the W83627UHG
hwmon: (w83627ehf) Clean up probe function
hwmon: (w83627ehf) Properly report PECI and AMD-SI sensor types
hwmon: Use i2c_smbus_{read,write}_word_swapped
hwmon: (smsc47b397) Fix checkpatch errors
hwmon: (lm90) Make code more readable
hwmon: (lm90) Fix warnings
hwmon: (ibmaem) Avoid repeated memory allocations
hwmon: (ibmaem) Make instance initializations independent
hwmon: (ibmaem) Fix error paths
hwmon: (lm73) Make detection less problematic
hwmon: Avoid building drivers for powerpc that read/write ISA addresses
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/tiwai/sound
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tiwai/sound: (24 commits)
ALSA: hda/realtek - Skip invalid digital out pins
ALSA: hda/sigmatel - Automatically retrieve digital I/O widgets
ALSA: hda - Remove unused variables
ALSA: hda/realtek - Don't create alt-stream for capture when unnecessary
ALSA: hda - Add support for 92HD65 / 92HD66 family of codecs
ALSA: hda - Disable power-widget control for IDT 92HD83/93 as default
ALSA: hda - Check NO_PRESENCE pincfg default bit
ASoC: Ensure we always delay for WM8962 FLL when starting from SYSCLK
ASoC: Ensure the WM8962 oscillator and PLLs start up disabled
ASoC: Ensure WM8962 PLL registers are reset
ALSA: intel8x0 - Fix inclusion of kvm_para.h
ALSA: hda_hwdep: Fix possible buffer overflow
ASoC: Fix return value of wm5100_gpio_direction_out()
ASoC: WM8904: Set `invert' bit for Capture Switch
ASoC: Leave input audio data bit length settings untouched in wm8711_set_dai_fmt
ASoC: wm8711: Fix wrong mask for setting input audio data bit length select
ALSA: intel8x0: Improve performance in virtual environment
ALSA: hdspm - Enable all firmware ranges for PCI MADI/AES cards
ALSA: hdsp - Correct HDSP_VERSION_BIT constant, thus partly fixing RPM detection
ALSA: hdspm - Fix MADI channel format in the status ioctl
...
|
|
* 'devicetree/merge' of git://git.secretlab.ca/git/linux-2.6:
dt: add empty of_machine_is_compatible
ahci: add DT binding for Calxeda AHCI controller
dt/platform: minor cleanup
dt: add empty of_alias_get_id() for non-dt builds
|
|
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/torvalds/linux into rmobile-latest
|
|
|
|
This fixes up support for SH-2(A) SCIFs by introducing a new regtype. As
expected, it's close to the SH-4A SCIF with fifodata, but still different
enough to warrant its own type.
Fixes up a number of FIFO overflows and similar for both SH7203/SH7264.
Signed-off-by: Phil Edworthy <phil.edworthy@renesas.com>
Tested-by: Federico Fuga <fuga@studiofuga.com>
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
|
|
In the case of 29bit mode, CAC/UNCAC_ADDR does not return a right address.
This revises this problem by using P1SEGADDR and P2SEGADDR in 29bit mode.
Reported-by: Yutaro Ebihara <ebiharaml@si-linux.co.jp>
Signed-off-by: Nobuhiro Iwamatsu <nobuhiro.iwamatsu.yj@renesas.com>
Tested-by: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Tested-by: Simon Horman <horms@verge.net.au>
Cc: stable@kernel.org
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
|
|
This service should not be registered with or unregistered from rpcbind.
Signed-off-by: Jeff Layton <jlayton@redhat.com>
Signed-off-by: Trond Myklebust <Trond.Myklebust@netapp.com>
|
|
The patch "ARM: gic: consolidate PPI handling" removes the usage
of test_for_ltirq. After the merge of imx6q remove this there, too.
Cc: Sascha Hauer <kernel@pengutronix.de>
Signed-off-by: Dirk Behme <dirk.behme@de.bosch.com>
Acked-by: Shawn Guo <shawn.guo@linaro.org>
Acked-by: Marc Zyngier <marc.zyngier@arm.com>
|
|
This is essentially a stripped down version of the W83627DHG. Noticeable
difference is that it is still powered with +5V, as older models, even
though the ADC resolution is 8 mV as newer models have.
Thanks to Ulf Bruman (Saab Group) for doing all the testing.
Signed-off-by: Jean Delvare <khali@linux-fr.org>
Acked-by: Guenter Roeck <guenter.roeck@ericsson.com>
|
|
The probe function has grown pretty large, I think it's time for some
cleanups, starting with these two simple ones:
* Move temp3/in6 check for the W83667HG later in the function, where
it is done for all other chip types.
* Move temperature register setting to a separate function, to avoid
code duplication.
Signed-off-by: Jean Delvare <khali@linux-fr.org>
Acked-by: Guenter Roeck <guenter.roeck@ericsson.com>
|
|
When temperature sources are PECI or AMD-SI agents, it makes no sense
to report their type as diode or thermistor. Instead we must report
their digital nature.
Signed-off-by: Jean Delvare <khali@linux-fr.org>
Cc: stable@kernel.org
Acked-by: Guenter Roeck <guenter.roeck@ericsson.com>
|
|
Make use of the new i2c_smbus_{read,write}_word_swapped functions.
This makes the driver code more compact and readable. It also ensures
proper error handling.
Signed-off-by: Jean Delvare <khali@linux-fr.org>
Acked-by: Jonathan Cameron <jic23@cam.ac.uk>
Acked-by: Guenter Roeck <guenter.roeck@ericsson.com>
Cc: Dirk Eibach <eibach@gdsys.de>
Cc: "Mark M. Hoffman" <mhoffman@lightlink.com>
Cc: Guillaume Ligneul <guillaume.ligneul@gmail.com>
|
|
Signed-off-by: Jean Delvare <khali@linux-fr.org>
Acked-by: Guenter Roeck <guenter.roeck@ericsson.com>
|
|
Clean up the code to make it more readable:
* Remove reg_ and new_ prefixes from variable names, they made the
names longer, causing extra line breaks, while not adding much
value.
* Introduce struct device dev* = &client->dev in two functions, to
avoid repeating client->dev everywhere in these functions.
Signed-off-by: Jean Delvare <khali@linux-fr.org>
Acked-by: Guenter Roeck <guenter.roeck@ericsson.com>
|
|
With some configuration option combinations, we get the following
warnings:
drivers/hwmon/lm90.c: In function 'lm90_detect':
drivers/hwmon/lm90.c:1114: warning: 'chip_id' may be used uninitialized
in this function
drivers/hwmon/lm90.c:1114: warning: 'reg_config1' may be used
uninitialized in this function
drivers/hwmon/lm90.c:1114: warning: 'reg_convrate' may be used
uninitialized in this function
drivers/hwmon/lm90.c:1187: warning: 'reg_emerg2' may be used
uninitialized in this function
drivers/hwmon/lm90.c:1187: warning: 'reg_status2' may be used
uninitialized in this function
We can solve these easily by reading the register values first and
checking for errors later. These errors should be very rare, even in
the case of failed detection, so this change has no impact on
performance. And this makes checkpatch.pl happier.
Reported-by: Guenter Roeck <guenter.roeck@ericsson.com>
Signed-off-by: Jean Delvare <khali@linux-fr.org>
Acked-by: Guenter Roeck <guenter.roeck@ericsson.com>
|
|
Preallocate a buffer for the response to sensor reads, and reuse it
for each read instead of allocating a new one each time. This should
be faster and should also avoid memory fragmentation.
Signed-off-by: Jean Delvare <khali@linux-fr.org>
Acked-by: Darrick J. Wong <djwong@us.ibm.com>
Acked-by: Guenter Roeck <guenter.roeck@ericsson.com>
|
|
There is no good reason that I can see why the failure to initialize
one instance should prevent other instances from being initialized.
Signed-off-by: Jean Delvare <khali@linux-fr.org>
Acked-by: Darrick J. Wong <djwong@us.ibm.com>
Acked-by: Guenter Roeck <guenter.roeck@ericsson.com>
|
|
I am under the impression that error paths in functions
aem_init_aem1_inst() and aem_init_aem2_inst() are incorrect. In
several cases, the function returns 0 on error, which I suspect is
not intended. Fix this by properly tracking error codes.
Signed-off-by: Jean Delvare <khali@linux-fr.org>
Acked-by: Darrick J. Wong <djwong@us.ibm.com>
Acked-by: Guenter Roeck <guenter.roeck@ericsson.com>
|
|
Word reads can cause trouble with some I2C devices, so do as much
detection as we can using only byte reads, and only use a word read in
the end to confirm the positive match. Also properly handle read
errors.
Signed-off-by: Jean Delvare <khali@linux-fr.org>
Acked-by: Guenter Roeck <guenter.roeck@ericsson.com>
Cc: Robert Casanova <robertcasanova@nanometrics.ca>
|
|
A modprobe of hwmon drivers that read/write ISA addresses on a powerpc results
in a kernel Oops. These reads/writes are being done via the inb()/in_8() and
outb()/out_8() macros.
Prevent these drivers from being built for powerpc.
Signed-off-by: Dean Nelson <dnelson@redhat.com>
Signed-off-by: Jean Delvare <khali@linux-fr.org>
|
|
Instead of calling into transport_emulate_control_cdb from
__transport_execute_tasks for some CDBs always set up ->exectute_tasks
in the command sequence and use it uniformly.
(nab: Add default passthrough break for SERVICE_ACTION_IN)
Signed-off-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: Nicholas Bellinger <nab@linux-iscsi.org>
|
|
All ->execute_task instances now need to complete the I/O explicitly,
which can either happen synchronously or asynchronously.
Note that a lot of the CDB emulations appear to return success even if
some lowlevel operations failed. Given that this is an existing issue
this patch doesn't change that fact.
(nab: Adding missing switch breaks in PR-IN + PR_OUT)
Signed-off-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: Nicholas Bellinger <nab@linux-iscsi.org>
|
|
After GPU lockup VRAM gart table is unpinned and thus its pointer
becomes unvalid. This patch move the unpin code to a common helper
function and set pointer to NULL so that page update code can check
if it should update GPU page table or not. That way bo still bound
to GART can be unbound (pci_unmap_page for all there page) properly
while there is no need to update the GPU page table.
V2 move the test for null gart out of the loop, small optimization
Signed-off-by: Jerome Glisse <jglisse@redhat.com>
Signed-off-by: Dave Airlie <airlied@redhat.com>
|
|
Encapsulate each CDB emulation into a function of its own, to prepare
setting ->exectute_task to these routines.
Signed-off-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: Nicholas Bellinger <nab@linux-iscsi.org>
|
|
We want to be able to handle all CDBs through it and remove hacks like
always using the first task in a CDB in target_report_luns.
Also rename the callback to ->execute_task to better describe its use.
Signed-off-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: Nicholas Bellinger <nab@linux-iscsi.org>
|
|
Split core_scsi2_emulate_crh into one routine each for the
PERSISTENT_RESERVE_IN and PERSISTENT_RESERVE_OUT side.
Signed-off-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: Nicholas Bellinger <nab@linux-iscsi.org>
|
|
Split core_scsi2_emulate_crh into one routine each for the reserve and
release side. The common code now is in a helper called by both
routines.
Signed-off-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: Nicholas Bellinger <nab@linux-iscsi.org>
|
|
This patch adds the initial pieces of generic active I/O shutdown logic.
This is intended to be a 'opt-in' feature for fabric modules that
includes the following functions to provide a mechinism for fabric
modules to track se_cmd via se_session->sess_cmd_list:
*) target_get_sess_cmd() - Add se_cmd to sess->sess_cmd_list, called
from fabric module incoming I/O path.
*) target_put_sess_cmd() - Check for completion or drop se_cmd from
->sess_cmd_list
*) target_splice_sess_cmd_list() - Splice active I/O list from
->sess_cmd_list to ->sess_wait_list, can called with HW fabric
lock held.
*) target_wait_for_sess_cmds() - Walk ->sess_wait_list waiting on
individual ->cmd_wait_comp. Optional transport_wait_for_tasks()
call.
target_splice_sess_cmd_list() is allowed to be called under HW fabric
lock, and performs the splice into se_sess->sess_wait_list and set
se_cmd->cmd_wait_set. Then target_wait_for_sess_cmds() walks the list
waiting for individual target_put_sess_cmd() fabric callbacks to
complete.
It also adds TFO->check_release_cmd() to split the completion and memory
release calls, where a fabric module uses target_put_sess_cmd() to check
for I/O completion during session shutdown. This is currently pushed out
into fabric modules as current fabric code may sleep here waiting for
TFO->check_stop_free() to complete in main response path, and because
target_wait_for_sess_cmds() calling TFO->release_cmd() to free fabric
descriptor memory directly.
Cc: Christoph Hellwig <hch@lst.de>
Cc: Roland Dreier <roland@purestorage.com>
Signed-off-by: Nicholas A. Bellinger <nab@linux-iscsi.org>
|
|
Reorder parms of cifs_lock_init, trivially simplify getlk code and
remove extra {} in cifs_lock_add_if.
Cc: Dan Carpenter <dan.carpenter@oracle.com>
Acked-by: Jeff Layton <jlayton@samba.org>
Signed-off-by: Pavel Shilovsky <piastry@etersoft.ru>
Signed-off-by: Steve French <sfrench@us.ibm.com>
|
|
Now we allocate a lock structure at first, then we request to the server
and save the lock if server returned OK though void function - it prevents
the situation when we locked a file on the server and then return -ENOMEM
from setlk.
Signed-off-by: Pavel Shilovsky <piastry@etersoft.ru>
Acked-by: Jeff Layton <jlayton@samba.org>
Signed-off-by: Steve French <sfrench@us.ibm.com>
|
|
The patch adds an empty function for non-dt build, so that
drivers migrating to dt can save some '#ifdef CONFIG_OF'.
v3: New patch
Signed-off-by: Stephen Warren <swarren@nvidia.com>
Signed-off-by: Grant Likely <grant.likely@secretlab.ca>
|
|
* git://git.samba.org/sfrench/cifs-2.6:
cifs: Assume passwords are encoded according to iocharset (try #2)
CIFS: Fix the VFS brlock cache usage in posix locking case
[CIFS] Update cifs version to 1.76
CIFS: Remove extra mutex_unlock in cifs_lock_add_if
|
|
* git://git.kernel.org/pub/scm/linux/kernel/git/davem/net: (45 commits)
be2net: Add detect UE feature for Lancer
be2net: Prevent CQ full condition for Lancer
be2net: Fix disabling multicast promiscous mode
be2net: Fix endian issue in RX filter command
af_packet: de-inline some helper functions
MAINTAINERS: Add can-gw include to maintained files
net: Add back alignment for size for __alloc_skb
net: add missing bh_unlock_sock() calls
l2tp: fix race in l2tp_recv_dequeue()
ixgbevf: Update release version
ixgbe: DCB, return max for IEEE traffic classes
ixgbe: fix reading of the buffer returned by the firmware
ixgbe: Fix compiler warnings
ixgbe: fix smatch splat due to missing NULL check
ixgbe: fix disabling of Tx laser at probe
ixgbe: Fix link issues caused by a reset while interface is down
igb: Fix for I347AT4 PHY cable length unit detection
e100: make sure vlan support isn't advertised on old adapters
e1000e: demote a debugging WARN to a debug log message
net: fix typo in drivers/net/ethernet/xilinx/ll_temac_main.c
...
|
|
devicetree/merge
|
|
Add code to detect UE in case of Lancer.
Signed-off-by: Padmanabh Ratnakar <padmanabh.ratnakar@emulex.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Indicate to HW that the CQ is cleaned up before posting new RX buffers.
This prevents the HW to go into CQ full error condition.
Signed-off-by: Padmanabh Ratnakar <padmanabh.ratnakar@emulex.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
If user tries to disable multicast promiscous mode, the adapter remains
in this mode as resetting the multicast promiscous mode was missing
in RX filter command. Fixed this.
Signed-off-by: Padmanabh Ratnakar <padmanabh.ratnakar@emulex.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Use cpu_to_le32() for mcast_num field in RX filter command as this
field is of type u32.
Signed-off-by: Padmanabh Ratnakar <padmanabh.ratnakar@emulex.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
|
|
The num_free field of mthca_buddy has a type of array of unsigned int
while it was allocated as an array of pointers. On 64-bit platforms
this allocates twice more than required. Fix this by allocating the
correct size for the type.
This is the same bug just fixed in mlx4 by Eli Cohen <eli@mellanox.co.il>.
Signed-off-by: Roland Dreier <roland@purestorage.com>
|
