| Age | Commit message (Collapse) | Author |
|---|
|
|
|
On sinks with a DPCD rev of 1.1 or greater, we can send sink power
management commands to address 0x600 per section 5.1.5 of the
DisplayPort 1.1a spec.
Signed-off-by: Jesse Barnes <jbarnes@virtuousgeek.org>
Reviewed-by: Keith Packard <keithp@keithp.com>
Signed-off-by: Keith Packard <keithp@keithp.com>
|
|
When checking link status during a hot plug event or detecting sink
presence, we need to retry 3 times per the spec (section 9.1 of the 1.1a
DisplayPort spec). Consolidate the retry code into a
native_aux_read_retry function for use by get_link_status and _detect.
Signed-off-by: Jesse Barnes <jbarnes@virtuousgeek.org>
Reviewed-by: Keith Packard <keithp@keithp.com>
Signed-off-by: Keith Packard <keithp@keithp.com>
|
|
We currently use this when a hot plug event is received, only checking
the link status and re-training if we had previously configured a link.
However if we want to preserve the DP configuration across both hot plug
and DPMS events (which we do for userspace apps that don't respond to
hot plug uevents), we need to unconditionally check the link and try to
bring it up on hot plug.
Signed-off-by: Jesse Barnes <jbarnes@virtuousgeek.org>
Reviewed-by: Keith Packard <keithp@keithp.com>
Signed-off-by: Keith Packard <keithp@keithp.com>
|
|
If ->detect is called too soon after a hot plug event, the sink may not
be ready yet. So try up to 3 times with 1ms sleeps in between tries to
get the data (spec dictates that receivers must be ready to respond within
1ms and that sources should try 3 times).
See section 9.1 of the 1.1a DisplayPort spec.
Signed-off-by: Jesse Barnes <jbarnes@virtuousgeek.org>
Reviewed-by: Keith Packard <keithp@keithp.com>
Signed-off-by: Keith Packard <keithp@keithp.com>
|
|
When a hotplug event is received, we need to check the receiver cap bits
in case they've changed (as they might with a hub or chain config).
Signed-off-by: Jesse Barnes <jbarnes@virtuousgeek.org>
Reviewed-by: Keith Packard <keithp@keithp.com>
Signed-off-by: Keith Packard <keithp@keithp.com>
|
|
Makes it easier to search for DP related constants.
Reviewed-by: Keith Packard <keithp@keithp.com>
Signed-off-by: Jesse Barnes <jbarnes@virtuousgeek.org>
Signed-off-by: Keith Packard <keithp@keithp.com>
|
|
Especially after a hotplug or power status change, the sink may not
reply immediately to a link status query. So retry 3 times per the spec
to really make sure nothing is there.
See section 9.1 of the 1.1a DisplayPort spec.
Signed-off-by: Jesse Barnes <jbarnes@virtuousgeek.org>
Reviewed-by: Keith Packard <keithp@keithp.com>
Signed-off-by: Keith Packard <keithp@keithp.com>
|
|
Now that we track bpp on a per-pipe basis, we can use the actual value
rather than assuming 24bpp.
Signed-off-by: Jesse Barnes <jbarnes@virtuousgeek.org>
Reviewed-by: Chris Wilson <chris@chris-wilson.co.uk>
Signed-off-by: Keith Packard <keithp@keithp.com>
|
|
This will catch bad fb configs earlier.
Signed-off-by: Jesse Barnes <jbarnes@virtuousgeek.org>
Reviewed-by: Chris Wilson <chris@chris-wilson.co.uk>
Signed-off-by: Keith Packard <keithp@keithp.com>
|
|
To properly drive a framebuffer with a new depth or bpp, dither settings
and link bandwidth calculations may change, so make sure we go through a
full mode set in that case.
Reported-by: Chris Wilson <chris@chris-wilson.co.uk>
Signed-off-by: Jesse Barnes <jbarnes@virtuousgeek.org>
Reviewed-by: Chris Wilson <chris@chris-wilson.co.uk>
Signed-off-by: Keith Packard <keithp@keithp.com>
|
|
The Intel HDMI encoder can support 8bpc or 12bpc. Set the appropriate
value based on the pipe bpp when configuring the output.
Signed-off-by: Jesse Barnes <jbarnes@virtuousgeek.org>
Reviewed-by: Chris Wilson <chris@chris-wilson.co.uk>
Signed-off-by: Keith Packard <keithp@keithp.com>
|
|
The pipe may be driving various bpp values depending on the display
configuration, so take that into account when calculating link bandwidth
requirements.
Signed-off-by: Jesse Barnes <jbarnes@virtuousgeek.org>
Reviewed-by: Chris Wilson <chris@chris-wilson.co.uk>
Signed-off-by: Keith Packard <keithp@keithp.com>
|
|
Updating the planes is device specific, so create a new display callback
and use it in pipe_set_base. (In fact we could go even further, valid
display plane bits have changed with each generation, as has tiled
buffer handling.)
Signed-off-by: Jesse Barnes <jbarnes@virtuousgeek.org>
Reviewed-by: Chris Wilson <chris@chris-wilson.co.uk>
Signed-off-by: Keith Packard <keithp@keithp.com>
|
|
Figuring out which pipe bpp to use is a bit painful. It depends on both
the encoder and display configuration attached to a pipe. For instance,
to drive a 24bpp framebuffer out to an 18bpp panel, we need to use 6bpc
on the pipe but also enable dithering. But driving that same
framebuffer to a DisplayPort output on another pipe means using 8bpc and
no dithering.
So split out and enhance the code to handle the various cases, returning
an appropriate pipe bpp as well as whether dithering should be enabled.
Save the resulting pipe bpp in the intel_crtc struct for use by encoders
in calculating bandwidth requirements (defaults to 24bpp on pre-ILK).
Signed-off-by: Jesse Barnes <jbarnes@virtuousgeek.org>
Reviewed-by: Chris Wilson <chris@chris-wilson.co.uk>
Signed-off-by: Keith Packard <keithp@keithp.com>
|
|
This may not be the default value, so pull the bpc out of the pipe reg
and write it to the DP transcoder so proper dithering and signaling
occurs.
Signed-off-by: Jesse Barnes <jbarnes@virtuousgeek.org>
Reviewed-by: Chris Wilson <chris@chris-wilson.co.uk>
Signed-off-by: Keith Packard <keithp@keithp.com>
|
|
This prevents us from setting reserved or incorrect bits on CougarPoint.
Signed-off-by: Jesse Barnes <jbarnes@virtuousgeek.org>
Reviewed-by: Chris Wilson <chris@chris-wilson.co.uk>
Signed-off-by: Keith Packard <keithp@keithp.com>
|
|
These bits are reserved on ILK+ (ILK+ provides this feature in the
transcoder and pipe configuration instead, which we already set).
Signed-off-by: Jesse Barnes <jbarnes@virtuousgeek.org>
Reviewed-by: Chris Wilson <chris@chris-wilson.co.uk>
Signed-off-by: Keith Packard <keithp@keithp.com>
|
|
|
|
* git://git.kernel.org/pub/scm/linux/kernel/git/jejb/scsi-rc-fixes-2.6: (277 commits)
[SCSI] isci: fix checkpatch errors
isci: Device reset should request sas_phy_reset(phy, true)
isci: pare back error messsages
isci: cleanup silicon revision detection
isci: merge scu_unsolicited_frame.h into unsolicited_frame_control.h
isci: merge sata.[ch] into request.c
isci: kill 'get/set' macros
isci: retire scic_sds_ and scic_ prefixes
isci: unify isci_host and scic_sds_controller
isci: unify isci_remote_device and scic_sds_remote_device
isci: unify isci_port and scic_sds_port
isci: fix scic_sds_remote_device_terminate_requests
isci: unify isci_phy and scic_sds_phy
isci: unify isci_request and scic_sds_request
isci: rename / clean up scic_sds_stp_request
isci: preallocate requests
isci: combine request flags
isci: unify can_queue tracking on the tci_pool, uplevel tag assignment
isci: Terminate dev requests on FIS err bit rx in NCQ
isci: fix frame received locking
...
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/arm/linux-2.6-arm-soc
* 'at91/fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/linux-2.6-arm-soc:
AT91: Change nand buswidth logic to match hardware default configuration
at91: Use "pclk" as con_id on at91cap9 and at91rm9200
at91: fix udc, ehci and mmc clock device name for cap9/9g45/9rl
atmel_serial: fix internal port num
at91: fix at91_set_serial_console: use platform device id
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/lethal/fbdev-3.x
* 'fbdev-fixes-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/lethal/fbdev-3.x:
vesafb: fix memory leak
fbdev: amba: Link fb device to its parent
fsl-diu-fb: remove check for pixel clock ranges
udlfb: Correct sub-optimal resolution selection.
hecubafb: add module_put on error path in hecubafb_probe()
sm501fb: fix section mismatch warning
gx1fb: Fix section mismatch warnings
fbdev: sh_mobile_meram: Correct pointer check for YCbCr chroma plane
|
|
Commits 71c29bd5c235 ("IB/uverbs: Add devnode method to set path/mode")
and c3af0980ce01 ("IB: Add devnode methods to cm_class and umad_class")
added devnode methods that set the mode.
However, these methods don't check for a NULL mode, and so we get a
crash when unloading modules because devtmpfs_delete_node() calls
device_get_devnode() with mode == NULL.
Add the missing checks.
Signed-off-by: Goldwyn Rodrigues <rgoldwyn@suse.de>
[ Also fix cm.c. - Roland ]
Signed-off-by: Roland Dreier <roland@purestorage.com>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
|
|
The recently modified nand buswitth configuration is not aligned with
board reality: the double footprint on boards is always populated with 8bits
buswidth nand flashes.
So we have to consider that without particular configuration the 8bits
buswidth is selected by default.
Moreover, the previous logic was always using !board_have_nand_8bit(), we
change it to a simpler: board_have_nand_16bit().
Signed-off-by: Nicolas Ferre <nicolas.ferre@atmel.com>
Tested-by: Ludovic Desroches <ludovic.desroches@atmel.com>
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
|
|
When releasing framebuffer, free colourmap allocations.
Signed-off-by: Daniel J Blueman <daniel.blueman@gmail.com>
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/rafael/suspend-2.6
* 'pm-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/rafael/suspend-2.6:
PM / Runtime: Update documentation regarding driver removal
PM: Documentation: fix typo: pm_runtime_idle_sync() doesn't exist.
|
|
Signed-off-by: James Bottomley <JBottomley@Parallels.com>
|
|
|
|
* git://git.kernel.org/pub/scm/linux/kernel/git/sfrench/cifs-2.6:
cifs: set socket send and receive timeouts before attempting connect
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/jdelvare/staging
* 'hwmon-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/jdelvare/staging:
hwmon: (k10temp) Update documentation for Fam12h
hwmon-vid: Fix typo in VIA CPU name
hwmon: (f71882fg) Add support for the F71869A
hwmon: Use <> rather than () around my e-mail address
hwmon: (emc6w201) Properly handle all errors
|
|
Add some CPU series IDs and links to the Fam12h datasheets.
Signed-off-by: Clemens Ladisch <clemens@ladisch.de>
Signed-off-by: Jean Delvare <khali@linux-fr.org>
|
|
It's Nehemiah, not Nemiah.
Signed-off-by: Jean Delvare <khali@linux-fr.org>
Acked-by: Guenter Roeck <guenter.roeck@ericsson.com>
|
|
The F71869A is almost the same as the F71869F/E, except that it has
the normal number of temp and pwm zones for a F71882FG derived chip,
rather then the limited number of the F71869F/E.
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Tested-by: Max Baldwin <archerseven@gmail.com>
Acked-by: Guenter Roeck <guenter.roeck@ericsson.com>
Signed-off-by: Jean Delvare <khali@linux-fr.org>
|
|
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Jean Delvare <khali@linux-fr.org>
|
|
Handle errors on 8-bit register reads and writes too. Also use likely
and unlikely to make the functions faster on success.
Signed-off-by: Jean Delvare <khali@linux-fr.org>
Acked-by: Guenter Roeck <guenter.roeck@ericsson.com>
|
|
The hard_reset parameter passed to the LLDD in the direct-attached
phy control case allows the LLDD to filter link failure events
while the direct-attached device reset is executing.
Signed-off-by: Jeff Skirvin <jeffrey.d.skirvin@intel.com>
Signed-off-by: Dan Williams <dan.j.williams@intel.com>
|
|
The messages emitted from task.c and some from request.c likely
duplicate (in a less undertandable way) what is reported by the
midlayer.
Signed-off-by: Dan Williams <dan.j.williams@intel.com>
|
|
Perform checking per-pci device (even though all systems will only have
1 pci device in this generation), and delete support for silicon that
does not report a proper revision (i.e. A0).
Reported-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: Dan Williams <dan.j.williams@intel.com>
|
|
Does not need its own file.
Signed-off-by: Dan Williams <dan.j.williams@intel.com>
|
|
Undo some needless separation.
Signed-off-by: Dan Williams <dan.j.williams@intel.com>
|
|
Most of these simple dereference macros are longer than their open coded
equivalent. Deleting enum sci_controller_mode is thrown in for good
measure.
Reported-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: Dan Williams <dan.j.williams@intel.com>
|
|
The distinction between scic_sds_ scic_ and sci_ are no longer relevant
so just unify the prefixes on sci_. The distinction between isci_ and
sci_ is historically significant, and useful for comparing the old
'core' to the current Linux driver. 'sci_' represents the former core as
well as the routines that are closer to the hardware and protocol than
their 'isci_' brethren. sci == sas controller interface.
Also unwind the 'sds1' out of the parameter structs.
Reported-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: Dan Williams <dan.j.williams@intel.com>
|
|
Remove the distinction between these two implementations and unify on
isci_host (local instances named ihost). Hmmm, we had two
'oem_parameters' instances, one was unused... nice.
Reported-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: Dan Williams <dan.j.williams@intel.com>
|
|
Remove the distinction between these two implementations and unify on
isci_remote_device (local instances named idev).
Reported-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: Dan Williams <dan.j.williams@intel.com>
|
|
Remove the distinction between these two implementations and unify on
isci_port (local instances named iport). The duplicate '->owning_port' and
'->isci_port' in both isci_phy and isci_remote_device will be fixed in a later
patch... this is just the straightforward rename/unification.
Reported-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: Dan Williams <dan.j.williams@intel.com>
|
|
Commit 0815632 "isci: unify remote_device stop_handlers" introduced the
possibility that not all requests get terminated if we reach the
request_count. Now that we properly reference count devices we don't
need this self-defense and can do the straightforward scan of all active
requests.
Reported-by: Jeff Skirvin <jeffrey.d.skirvin@intel.com>
Acked-by: Jeff Skirvin <jeffrey.d.skirvin@intel.com>
Signed-off-by: Dan Williams <dan.j.williams@intel.com>
|
|
They are one in the same object so remove the distinction. The near
duplicate fields (owning_port, and isci_port) will be cleaned up
after the scic_sds_port isci_port unification.
Reported-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: Dan Williams <dan.j.williams@intel.com>
|
|
They are one in the same object so remove the distinction. The near
duplicate fields (owning_controller, and isci_host) will be cleaned up
after the scic_sds_contoller isci_host unification.
Reported-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: Dan Williams <dan.j.williams@intel.com>
|
|
* Rename scic_sds_stp_request to isci_stp_request
* Remove the unused fields and union indirection
Reported-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: Dan Williams <dan.j.williams@intel.com>
|
|
the dma_pool interface is optimized for object_size << page_size which
is not the case with isci_request objects and the dma_pool routines show
up in the top of the profile.
The old io_request_table which tracked whether tci slots were in-flight
or not is replaced with an IREQ_ACTIVE flag per request.
Signed-off-by: Dan Williams <dan.j.williams@intel.com>
|
