| Age | Commit message (Collapse) | Author |
|---|
|
Signed-off-by: Fred Isaman <iisaman@netapp.com>
Signed-off-by: Trond Myklebust <Trond.Myklebust@netapp.com>
|
|
PipeFS superblock creation routine relays on SUNRPC pernet data presense, which
is created on register_pernet_subsys() call in SUNRPC module init function.
Registering of PipeFS filesystem prior to registering of per-net subsystem
leads to races (mount of PipeFS can dereference uninitialized data).
Signed-off-by: Stanislav Kinsbursky <skinsbursky@parallels.com>
Signed-off-by: Trond Myklebust <Trond.Myklebust@netapp.com>
|
|
Setting the correct mode is required by rc-core or scancodes won't be
generated (which isn't very user-friendly).
This one-line fix should be suitable for 3.4-rc2.
Signed-off-by: David Härdeman <david@hardeman.nu>
Cc: stable@kernel.org
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
|
|
If sanity check fails in scu_command(), goto error leads to unlock of
an unheld mutex. The check should not fail in reality, but it nevertheless
worth fixing.
Found by Linux Driver Verification project (linuxtesting.org).
Signed-off-by: Alexey Khoroshilov <khoroshilov@ispras.ru>
Cc: stable@kernel.org
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
|
|
There are some softwares (Kaffeine and likely xine) that uses a
DVBv5 call to switch to DVB-S2, but expects that a DVBv3 call to
switch back to DVB-S. Well, this is not right, as a DVBv3 call
doesn't know anything about delivery systems.
However, as, by accident, this used to work, we need to restore its
behavior, in order to avoid regressions with those softwares.
Reported on this Fedora 16 bugzilla:
https://bugzilla.redhat.com/show_bug.cgi?id=812895
Reported-by: Dieter Roever <Dieter.Roever@gmx.de>
Cc: stable@kernel.org # for version 3.3
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
|
|
Sven Joachim reported, that suspend/resume on rc3 trips over a NULL
pointer dereference. Linus spotted the clockevent handler being NULL.
commit fa4da365b(clockevents: tTack broadcast device mode change in
tick_broadcast_switch_to_oneshot()) tried to fix a problem with the
broadcast device setup, which was introduced in commit 77b0d60c5(
clockevents: Leave the broadcast device in shutdown mode when not
needed).
The initial commit avoided to set up the broadcast device when no
broadcast request bits were set, but that left the broadcast device
disfunctional. In consequence deep idle states which need the
broadcast device were not woken up.
commit fa4da365b tried to fix that by initializing the state of the
broadcast facility, but that missed the fact, that nothing initializes
the event handler and some other state of the underlying clock event
device.
The fix is to revert both commits and make only the mode setting of
the clock event device conditional on the state of active broadcast
users.
That initializes everything except the low level device mode, but this
happens when the broadcast functionality is invoked by deep idle.
Reported-and-tested-by: Sven Joachim <svenjoac@gmx.de>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Cc: Rafael J. Wysocki <rjw@sisk.pl>
Cc: Linus Torvalds <torvalds@linux-foundation.org>
Cc: Suresh Siddha <suresh.b.siddha@intel.com>
Link: http://lkml.kernel.org/r/alpine.LFD.2.02.1204181205540.2542@ionos
|
|
usb_nop_xceiv_unregister is needed on failure of usb_get_transceiver, as
done in other error-handling code in the same function.
Signed-off-by: Julia Lawall <Julia.Lawall@lip6.fr>
Signed-off-by: Felipe Balbi <balbi@ti.com>
|
|
Looks like we cannot live without that double_buffer_not_ok
flag due to many HW bugs this MUSB core has.
So, let's drop the __deprecated flag to avoid annoying
compile warnings.
Signed-off-by: Felipe Balbi <balbi@ti.com>
|
|
The imx5_idle() check of the tzic_eanble_wake() return value uses
incorrect (inverted) logic causing all attempt to idle to fail.
Signed-off-by: Robert Lee <rob.lee@linaro.org>
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
|
|
commit 6b783f7c (irq_domain: Remove irq_domain_add_simple()
replaced irq_domain_add_simple with irq_domain_add_legacy()
Implement this conversion so that imx27-dt can be built again.
Reported-by: Chris Ball <cjb@laptop.org>
Signed-off-by: Fabio Estevam <fabio.estevam@freescale.com>
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
|
|
Add support for CONFIG_REGULATOR_FIXED_VOLTAGE.
Without this option the mx27_3ds cannot have the external Ethernet functional
due to the need of smsc regulators.
Signed-off-by: Fabio Estevam <fabio.estevam@freescale.com>
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
|
|
Not only do the pageflip work without it at non-native modes (i.e. with
the panel fitter enabled), it also causes normal (non-pageflipped)
modesets to fail.
Reported-by: Adam Jackson <ajax@redhat.com>
Tested-by: Adam Jackson <ajax@redhat.com>
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Wanted-by-for-fixes: Dave Airlie <airlied@gmail.com>
Signed-Off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
|
|
Leading up to the ->device_prep_slave_sg change in
185ecb5f4fd43911c35956d4cc7d94a1da30417f 'dmaengine: add context
parameter to prep_slave_sg and prep_dma_cyclic' a generic wrapper was
added in place to guard against the API change, though the fsi driver
wasn't updated in the process (presumably its dmaengine support hadn't
been merged yet at the time). This trivially switches over to the new
wrapper and gets it building again.
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
Acked-by: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
|
|
Fix kernel-doc warning in sound/core/vmaster.c:
Warning(sound/core/vmaster.c:429): No description found for parameter 'private_data'
Signed-off-by: Randy Dunlap <rdunlap@xenotime.net>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
|
|
ops_init should free the net_generic data on
init failure and __register_pernet_operations should not
call ops_free when NET_NS is not enabled.
Signed-off-by: Julian Anastasov <ja@ssi.bg>
Reviewed-by: "Eric W. Biederman" <ebiederm@xmission.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/jkirsher/net
|
|
If a process increases permissions using fcaps all of the dangerous
personality flags which are cleared for suid apps should also be cleared.
Thus programs given priviledge with fcaps will continue to have address space
randomization enabled even if the parent tried to disable it to make it
easier to attack.
Signed-off-by: Eric Paris <eparis@redhat.com>
Reviewed-by: Serge Hallyn <serge.hallyn@canonical.com>
Signed-off-by: James Morris <james.l.morris@oracle.com>
|
|
Fix kernel-doc warning in net/sock.h:
Warning(include/net/sock.h:377): No description found for parameter 'sk_peek_off'
Signed-off-by: Randy Dunlap <rdunlap@xenotime.net>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
tcp_grow_window() has to grow rcv_ssthresh up to window_clamp, allowing
sender to increase its window.
tcp_grow_window() still assumes a tcp frame is under MSS, but its no
longer true with LRO/GRO.
This patch fixes one of the performance issue we noticed with GRO on.
Signed-off-by: Eric Dumazet <edumazet@google.com>
Cc: Neal Cardwell <ncardwell@google.com>
Cc: Tom Herbert <therbert@google.com>
Acked-by: Neal Cardwell <ncardwell@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Free card->mem in the error-handling code since it was successfully
allocated just above.
Signed-off-by: Julia Lawall <Julia.Lawall@lip6.fr>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Under heavy load (flood ping) it is possible for the MDIO timeout to
expire before the loop checks the GO bit again. This patch adds an
additional check whether the operation was done before actually
returning -ETIMEDOUT.
To reproduce this bug, flood ping the device, e.g., ping -f -l 1000
After some time, a "timed out waiting for user access" warning
may appear. And even worse, link may go down since the PHY reported a
timeout.
Signed-off-by: Christian Riesch <christian.riesch@omicron.at>
Cc: <stable@vger.kernel.org>
Cc: Cyril Chemparathy <cyril@ti.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Functionally, this change is a NOP.
Semantically, rt6_clean_expires() wants to do rt->dst.from = NULL instead of
rt->dst.expires = 0. It is clearing the RTF_EXPIRES flag, so the union is going
to be treated as a pointer (dst.from) not a long (dst.expires).
Signed-off-by: Jiri Bohac <jbohac@suse.cz>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Commit 1716a961 (ipv6: fix problem with expired dst cache) broke PMTU
discovery. rt6_update_expires() calls dst_set_expires(), which only updates
dst->expires if it has not been set previously (expires == 0) or if the new
expires is earlier than the current dst->expires.
rt6_update_expires() needs to zero rt->dst.expires, otherwise it will contain
ivalid data left over from rt->dst.from and will confuse dst_set_expires().
Signed-off-by: Jiri Bohac <jbohac@suse.cz>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
arcrimi_probe() calls BUGMSG() before register_netdev() happens. BUGMSG()
itself prints dev->name, but as the format string hasn't been expanded by
register_netdev() yet, the output contains bogus device name such as
arc%d: Given: node 00h, shmem 0h, irq 0
As we don't know the device name yet, just drop the prefix completely from
the debugging messages.
Reported-by: Steven Young <sdyoung@vt220.org>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
At the start of the function we assign 'a->d' to 'ap'. Then we use the
RESIZE_IF_NEEDED macro on 'a' - this may free 'a->d' and replace it
with newly allocaetd storage. In that case, we'll be operating on
freed memory further down in the function when we index into 'ap[]'.
Since we don't actually need 'ap' until after the use of the
RESIZE_IF_NEEDED macro we can just delay the assignment to it until
after we've potentially resized, thus avoiding the issue.
While I was there anyway I also changed the integer variable 'n' to be
const. It might as well be since we only assign to it once and use it
as a constant, and then the compiler will tell us if we ever assign to
it in the future.
Signed-off-by: Jesper Juhl <jj@chaosbits.net>
Acked-by: Dmitry Kasatkin <dmitry.kasatkin@intel.com>
Signed-off-by: James Morris <james.l.morris@oracle.com>
|
|
A kernel with Smack enabled will fail if tmpfs has xattr support.
Move the initialization of predefined Smack label
list entries to the LSM initialization from the
smackfs setup. This became an issue when tmpfs
acquired xattr support, but was never correct.
Signed-off-by: Casey Schaufler <casey@schaufler-ca.com>
Signed-off-by: James Morris <james.l.morris@oracle.com>
|
|
pl022 ssp controller supports word lengths from 4 to 16 (or 32) bits.
Currently implemented checks were incorrect. It has following check
if (pl022->vendor->max_bpw >= 32)
which must be checking for <=.
Also error print message is incorrect, that prints "range is from 1 to
16".
Fix both these issues.
Signed-off-by: Vinit Shenoy <vinit.shenoy@st.com>
Acked-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Grant Likely <grant.likely@secretlab.ca>
|
|
This patch (as1542) changes the criterion ehci-hcd uses to tell when
it needs to resume the controller's root hub. A resume is needed when
a port status change is detected, obviously, but only if the root hub
is currently suspended.
Right now the driver tests whether the root hub is running, and that
is not the correct test. In particular, if the controller has died
then the root hub should not be restarted. In addition, some buggy
hardware occasionally requires the root hub to be running and
sending out SOF packets even while it is nominally supposed to be
suspended.
In the end, the test needs to be changed. Rather than checking whether
the root hub is currently running, the driver will now check whether
the root hub is currently suspended. This will yield the correct
behavior in all cases.
Signed-off-by: Alan Stern <stern@rowland.harvard.edu>
CC: Peter Chen <B29397@freescale.com>
Cc: stable <stable@vger.kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
These devices have a number of non serial interfaces as well. Use
the existing "Direct IP" blacklist to prevent binding to interfaces
which are handled by other drivers.
We also extend the "Direct IP" blacklist with with interfaces only
seen in "QMI" mode, assuming that these devices use the same
interface numbers for serial interfaces both in "Direct IP" and in
"QMI" mode.
Signed-off-by: Bjørn Mork <bjorn@mork.no>
Cc: stable <stable@vger.kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
A large `nents' from userspace could overflow the allocation size,
leading to memory corruption.
| alloc_sglist()
| usbtest_ioctl()
Use kmalloc_array() to avoid the overflow.
Signed-off-by: Xi Wang <xi.wang@gmail.com>
Acked-by: Alan Stern <stern@rowland.harvard.edu>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
Avoid overflowing context.count = param->sglen * param->iterations,
where both `sglen' and `iterations' are from userspace.
| test_ctrl_queue()
| usbtest_ioctl()
Keep -EOPNOTSUPP for error code.
Signed-off-by: Xi Wang <xi.wang@gmail.com>
Acked-by: Alan Stern <stern@rowland.harvard.edu>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
This patch (as154) fixes a self-deadlock that occurs when userspace
writes to the bConfigurationValue sysfs attribute for a hub with
children. The task tries to lock the bandwidth_mutex at a time when
it already owns the lock:
The attribute's method calls usb_set_configuration(),
which calls usb_disable_device() with the bandwidth_mutex
held.
usb_disable_device() unregisters the existing interfaces,
which causes the hub driver to be unbound.
The hub_disconnect() routine calls hub_quiesce(), which
calls usb_disconnect() for each of the hub's children.
usb_disconnect() attempts to acquire the bandwidth_mutex
around a call to usb_disable_device().
The solution is to make usb_disable_device() acquire the mutex for
itself instead of requiring the caller to hold it. Then the mutex can
cover only the bandwidth deallocation operation and not the region
where the interfaces are unregistered.
This has the potential to change system behavior slightly when a
config change races with another config or altsetting change. Some of
the bandwidth released from the old config might get claimed by the
other config or altsetting, make it impossible to restore the old
config in case of a failure. But since we don't try to recover from
config-change failures anyway, this doesn't matter.
[This should be marked for stable kernels that contain the commit
fccf4e86200b8f5edd9a65da26f150e32ba79808 "USB: Free bandwidth when
usb_disable_device is called."
That commit was marked for stable kernels as old as 2.6.32.]
Signed-off-by: Alan Stern <stern@rowland.harvard.edu>
Signed-off-by: Sarah Sharp <sarah.a.sharp@linux.intel.com>
Cc: stable <stable@vger.kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
This patch makes it so that we identify FCoE rings earlier than
ixgbe_set_rx_buffer_len. Instead we identify the Rx FCoE rings at
allocation time in ixgbe_alloc_q_vector.
The motivation behind this change is to avoid memory corruption when FCoE
is enabled. Without this change we were initializing the rings at 0, and
2K on systems with 4K pages, then when we bumped the buffer size to 4K with
order 1 pages we were accessing offsets 2K and 6K instead of 0 and 4K.
This was resulting in memory corruptions.
Signed-off-by: Alexander Duyck <alexander.h.duyck@intel.com>
Acked-by: Yi Zou <yi.zou@intel.com>
Tested-by: Ross Brattain <ross.b.brattain@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
|
|
Upon resume from standby, ixgbe may trigger the ASSERT_RTNL() in
netif_set_real_num_tx_queues(). The call stack is:
netif_set_real_num_tx_queues
ixgbe_set_num_queues
ixgbe_init_interrupt_scheme
ixgbe_resume
Signed-off-by: Benjamin Poirier <bpoirier@suse.de>
Tested-by: Stephen Ko <stephen.s.ko@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
|
|
DMTIMER source selection on OMAP1 is broken. omap1_dm_timer_set_src()
tries to use __raw_{read,write}l() to read from and write to physical
addresses, but those functions take virtual addresses.
sparse caught this:
arch/arm/mach-omap1/timer.c:50:13: warning: incorrect type in argument 1 (different base types)
arch/arm/mach-omap1/timer.c:50:13: expected void const volatile [noderef] <asn:2>*<noident>
arch/arm/mach-omap1/timer.c:50:13: got unsigned int
arch/arm/mach-omap1/timer.c:52:9: warning: incorrect type in argument 1 (different base types)
arch/arm/mach-omap1/timer.c:52:9: expected void const volatile [noderef] <asn:2>*<noident>
arch/arm/mach-omap1/timer.c:52:9: got unsigned int
Fix by using omap_{read,writel}(), just like the other users of the
MOD_CONF_CTRL_1 register in the OMAP1 codebase. Of course, in the long term,
removing omap_{read,write}l() is the appropriate thing to do; but
this will take some work to do this cleanly.
Looks like this was caused by 97933d6 (ARM: OMAP1: dmtimer: conversion
to platform devices) that dangerously moved code and changed it in
the same patch.
Signed-off-by: Paul Walmsley <paul@pwsan.com>
Cc: Tarun Kanti DebBarma <tarun.kanti@ti.com>
Cc: stable@vger.kernel.org
[tony@atomide.com: updated comments to include the breaking commit]
Signed-off-by: Tony Lindgren <tony@atomide.com>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/tytso/ext4
Pull ext4 regression fixes from Ted Ts'o:
"This fixes a scalability problem reported by Andi Kleen and Tim Chen;
they were quite secretive about the precise nature of their workload,
but they later admitted that it only showed up when they were using a
large sparse file, so the amount of data I/O that was needed was close
to zero.
I'm not sure how realistic this is and it's only a regression if you
consider changes made since 2.6.39 to be a "regression" vis-a-vis the
policy regarding post-merge window bug fixes, but Linus agreed it was
worth fixing, so I'm including it in this pull request.
This also fixes the journalled quota mount options, which I
accidentally broke while I was cleaning up the mount option handling."
* tag 'ext4_for_linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tytso/ext4:
ext4: fix handling of journalled quota options
ext4: address scalability issue by removing extent cache statistics
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/viro/vfs
Pull vfs fixes from Al Viro:
"A bunch of endianness fixes and a couple of nfsd error value fixes.
Speaking of endianness stuff, I'm rather tempted to slap
ccflags-y += -D__CHECK_ENDIAN__
in fs/Makefile, if not making it default for the entire tree; nfsd
regressions I've caught make one hell of a pile and we'd obviously
benefit from having that kind of stuff caught earlier..."
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/viro/vfs:
lockd: fix the endianness bug
ocfs2: ->e_leaf_clusters endianness breakage
ocfs2: ->rl_count endianness breakage
ocfs: ->rl_used breakage on big-endian
ocfs2: ->l_next_free_req breakage on big-endian
btrfs: btrfs_root_readonly() broken on big-endian
ext4: fix endianness breakage in ext4_split_extent_at()
nfsd: fix compose_entry_fh() failure exits
nfsd: fix error value on allocation failure in nfsd4_decode_test_stateid()
nfsd: fix endianness breakage in TEST_STATEID handling
nfsd: fix error values returned by nfsd4_lockt() when nfsd_open() fails
nfsd: fix b0rken error value for setattr on read-only mount
|
|
Currently we increment the number of RTD's per card during the DAI link
bind. This can cause an incorrect RTD count when we cannot find a component
and defer the probe (and hence perform the DAI link bind for the card again).
Fix the count so that it is cleared before every card registration
and bind attempt.
Signed-off-by: Liam Girdwood <lrg@ti.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
|
|
The current serial UART code, while fidling with ocp idlemode bits,
forget about the smart idle wakeup bit even if it is supported by
UART IP block. This will lead to missing the module wakeup on OMAP's
where the smart idle wakeup is supported.
This was the root cause of the console sluggishness issue, I have been
observing on OMAP4 devices and also can be potential reason for some
other UART wakeup issues.
Signed-off-by: Santosh Shilimkar <santosh.shilimkar@ti.com>
Acked-by: Kevin Hilman <khilman@ti.com>
Acked-by: Govindraj.R <govindraj.raja@ti.com>
Reviewed-by: Paul Walmsley <paul@pwsan.com>
Cc: stable@vger.kernel.org
Signed-off-by: Tony Lindgren <tony@atomide.com>
|
|
Assigning sequence number for frames without taking care
of the fragment field breaks transmission of fragmented frames.
Fix this by assigning the fragment number properly.
Signed-off-by: Sujith Manoharan <c_manoha@qca.qualcomm.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
|
|
The broken check leads to rate control attempting to use HT40 while
the driver is configured for HT20. This leads to interesting hardware
issues.
HT40 can only be used if the channel type is either HT40- or HT40+
and if the channel type of the cell matches the local type.
Signed-off-by: Felix Fietkau <nbd@openwrt.org>
Cc: stable@vger.kernel.org
Signed-off-by: John W. Linville <linville@tuxdriver.com>
|
|
Add Johannes Berg as the primary maintainer for iwlwifi driver
Signed-off-by: Wey-Yi Guy <wey-yi.w.guy@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
|
|
Cooked monitor rx was recently changed to use ieee80211_add_rx_radiotap_header
instead of generating only limited radiotap information.
ieee80211_add_rx_radiotap_header assumes that FCS info is still present if
the hardware supports receiving it, however when cooked monitor rx packets
are processed, FCS info has already been stripped.
Fix this by adding an extra flag indicating FCS presence.
Signed-off-by: Felix Fietkau <nbd@openwrt.org>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
|
|
Commit (7496ba3 ARM: OMAP2+: UART: Add default mux for all uarts)
wrongly added muxing of default pads for all uarts. This causes
breakage on multiple boards using uart pins for alternate functions.
For example, on zoom3 random oopses can be seen with nfsroot as
the smsc911x ethernet FIFO timings on GPMC bus are controlled
by gpmc_wait2 and gpmc_wait3 pins. This means we can't mux these
pads to uart4 functionality as commit 7496ba3 was doing.
Not all boards tend to use all uarts and most of unused uart pins
are muxed for other purpose. This commit breaks the modules which
where trying to use unused uart pins on their boards.
So remove the default pad muxing. Note that this is not a complete
fix, as we now rely on bootloader set muxing for the uart wake-up
events. Further patching is needed to enable wake-up events for
uarts that are already muxed to uart mode.
Cc: Felipe Balbi <balbi@ti.com>
Cc: Kevin Hilman <khilman@ti.com>
Acked-by: Russ Dill <russ.dill@gmail.com>
Reported-by: Tony Lindgren <tony@atomide.com>
Signed-off-by: Govindraj.R <govindraj.raja@ti.com>
[tony@atomide.com: updated comments to describe oops on zoom3]
Signed-off-by: Tony Lindgren <tony@atomide.com>
|
|
Use list_for_each_entry_safe and remove the spin_lock acquisition in
m2p_find_override.
Signed-off-by: Stefano Stabellini <stefano.stabellini@eu.citrix.com>
Signed-off-by: Konrad Rzeszutek Wilk <konrad.wilk@oracle.com>
|
|
Since we are using the m2p_override we do have struct pages
corresponding to the user vma mmap'ed by gntdev.
Removing the VM_PFNMAP flag makes get_user_pages work on that vma.
An example test case would be using a Xen userspace block backend
(QDISK) on a file on NFS using O_DIRECT.
CC: stable@kernel.org
Signed-off-by: Stefano Stabellini <stefano.stabellini@eu.citrix.com>
Signed-off-by: Konrad Rzeszutek Wilk <konrad.wilk@oracle.com>
|
|
_omap3_sram_configure_core_dpll is called when SDRC is reprogrammed,
which is done regardless of CONFIG_PM setting, so we always need it's
setup code too. Without this, we hit a BUG() on OMAP3 when kernel is
built without CONFIG_PM:
Reprogramming SDRC clock to 332000000 Hz
------------[ cut here ]------------
kernel BUG at arch/arm/plat-omap/sram.c:342!
Internal error: Oops - BUG: 0 [#1] ARM
...
[<c001c694>] (omap3_configure_core_dpll+0x68/0x6c) from [<c001b2dc>] (omap3_core_dpll_m2_set_rate+0x1)
[<c001b2dc>] (omap3_core_dpll_m2_set_rate+0x138/0x1b0) from [<c001a478>] (omap2_clk_set_rate+0x14/0x2)
[<c001a478>] (omap2_clk_set_rate+0x14/0x20) from [<c001c9dc>] (clk_set_rate+0x54/0x74)
[<c001c9dc>] (clk_set_rate+0x54/0x74) from [<c022b9c8>] (omap_sdrc_init+0x70/0x90)
[<c022b9c8>] (omap_sdrc_init+0x70/0x90) from [<c022f178>] (omap3pandora_init+0x11c/0x164)
[<c022f178>] (omap3pandora_init+0x11c/0x164) from [<c022849c>] (customize_machine+0x20/0x28)
[<c022849c>] (customize_machine+0x20/0x28) from [<c0225810>] (do_one_initcall+0xa0/0x16c)
[<c0225810>] (do_one_initcall+0xa0/0x16c) from [<c02259e0>] (kernel_init+0x104/0x1ac)
[<c02259e0>] (kernel_init+0x104/0x1ac) from [<c0009cec>] (kernel_thread_exit+0x0/0x8)
Signed-off-by: Grazvydas Ignotas <notasas@gmail.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
|
|
Pull CIFS fixes from Steve French.
* git://git.samba.org/sfrench/cifs-2.6:
Fix number parsing in cifs_parse_mount_options
Cleanup handling of NULL value passed for a mount option
|
|
As of:
29494be71afe ("rcu,cleanup: simplify the code when cpu is dying")
RCU adopts callbacks from the dying CPU in its CPU_DYING notifier,
which means that any callbacks posted by later CPU_DYING notifiers
are ignored until the CPU comes back online.
A WARN_ON_ONCE() was added to __call_rcu() by:
e56014000816 ("rcu: Simplify offline processing")
to check for this condition. Although this condition did not trigger
(at least as far as I know) during -next testing, it did recently
trigger in mainline:
https://lkml.org/lkml/2012/4/2/34
What is needed longer term is for RCU's CPU_DEAD notifier to adopt any
callbacks that were posted by CPU_DYING notifiers, however, the Linux
kernel has been running with this sort of thing happening for quite
some time. So the only thing that qualifies as a regression is the
WARN_ON_ONCE(), which this commit removes.
Making RCU's CPU_DEAD notifier adopt callbacks posted by CPU_DYING
notifiers is a topic for the 3.5 release of the Linux kernel.
Reported-by: Sergey Senozhatsky <sergey.senozhatsky@gmail.com>
Signed-off-by: Paul E. McKenney <paul.mckenney@linaro.org>
Signed-off-by: Paul E. McKenney <paulmck@linux.vnet.ibm.com>
|
|
Remove SoC dependency and make it generic for every Atmel ARM AT91. That will
allow to select this driver for newer chips. Keep dependency on AT91 because of
the use of an header file located in include/mach directory.
Modify the comment to reflect this.
Signed-off-by: Nicolas Ferre <nicolas.ferre@atmel.com>
Acked-by: Vinod Koul <vinod.koul@linux.intel.com>
|
