| Age | Commit message (Collapse) | Author |
|---|
|
The dw_dmac driver was originally developed for avr32 to be used with the
Synopsys DesignWare AHB DMA controller. Starting from 2.6.38, access to
the device's i/o memory was done with the little-endian readl/writel
functions(1)
This broke the driver for the avr32 platform, because it needs big
(native) endian accessors. This patch makes the endianness configurable
using 'DW_DMAC_BIG_ENDIAN_IO', which will default be true for AVR32
I submitted this patch before(2) but then waited for Andy to finish other
changes to the same module(3).
(1) https://patchwork.kernel.org/patch/608211
(2) https://lkml.org/lkml/2012/8/26/148
(3) https://lkml.org/lkml/2012/9/21/173
Signed-off-by: Hein Tibosch <hein_tibosch@yahoo.es>
Acked-by: Arnd Bergmann <arnd@arndb.de>
Cc: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Acked-by: Viresh Kumar <viresh.kumar@linaro.org>
Cc: Hans-Christian Egtvedt <egtvedt@samfundet.no>
Cc: Ludovic Desroches <ludovic.desroches@atmel.com>
Cc: Havard Skinnemoen <havard@skinnemoen.net>
Cc: Nicolas Ferre <nicolas.ferre@atmel.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
|
|
While allocating mmu_notifier with parameter GFP_KERNEL, swap would start
to work in case of tight available memory. Eventually, that would lead to
a deadlock while the swap deamon swaps anonymous pages. It was caused by
commit e0f3c3f78da29b ("mm/mmu_notifier: init notifier if necessary").
=================================
[ INFO: inconsistent lock state ]
3.7.0-rc1+ #518 Not tainted
---------------------------------
inconsistent {RECLAIM_FS-ON-W} -> {IN-RECLAIM_FS-W} usage.
kswapd0/35 [HC0[0]:SC0[0]:HE1:SE1] takes:
(&mapping->i_mmap_mutex){+.+.?.}, at: page_referenced+0x9c/0x2e0
{RECLAIM_FS-ON-W} state was registered at:
mark_held_locks+0x86/0x150
lockdep_trace_alloc+0x67/0xc0
kmem_cache_alloc_trace+0x33/0x230
do_mmu_notifier_register+0x87/0x180
mmu_notifier_register+0x13/0x20
kvm_dev_ioctl+0x428/0x510
do_vfs_ioctl+0x98/0x570
sys_ioctl+0x91/0xb0
system_call_fastpath+0x16/0x1b
irq event stamp: 825
hardirqs last enabled at (825): _raw_spin_unlock_irq+0x30/0x60
hardirqs last disabled at (824): _raw_spin_lock_irq+0x19/0x80
softirqs last enabled at (0): copy_process+0x630/0x17c0
softirqs last disabled at (0): (null)
...
Simply back out the above commit, which was a small performance
optimization.
Signed-off-by: Gavin Shan <shangw@linux.vnet.ibm.com>
Reported-by: Andrea Righi <andrea@betterlinux.com>
Tested-by: Andrea Righi <andrea@betterlinux.com>
Cc: Wanpeng Li <liwanp@linux.vnet.ibm.com>
Cc: Andrea Arcangeli <aarcange@redhat.com>
Cc: Avi Kivity <avi@redhat.com>
Cc: Hugh Dickins <hughd@google.com>
Cc: Marcelo Tosatti <mtosatti@redhat.com>
Cc: Xiao Guangrong <xiaoguangrong@linux.vnet.ibm.com>
Cc: Sagi Grimberg <sagig@mellanox.co.il>
Cc: Haggai Eran <haggaie@mellanox.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
|
|
Latest Linus head run of "make selftests" in the tools directory failed
with references to undefined variables. Reference was to
'write_thread_data' which is the name of a struct that is being used, not
the variable itself. Change reference so it points to the variable.
Signed-off-by: Daniel Hazelton <dshadowwolf@gmail.com>
Cc: "Paton J. Lewis" <palewis@adobe.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
|
|
Fix tools/vm/page-types.c to use the UAPI variant of linux/kernel-page-flags.h
lest the following error appear:
In file included from page-types.c:38:0:
../../include/linux/kernel-page-flags.h:4:42: fatal error:
uapi/linux/kernel-page-flags.h: No such file or directory
Reported-by: Daniel Hazelton <dshadowwolf@gmail.com>
Signed-off-by: David Howells <dhowells@redhat.com>
Reviewed-by: Fengguang Wu <fengguang.wu@intel.com>
Tested-by: Daniel Hazelton <dshadowwolf@gmail.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
|
|
If start_isolate_page_range() failed, unset_migratetype_isolate() has been
done inside it.
Signed-off-by: Bob Liu <lliubbo@gmail.com>
Cc: Ni zhan Chen <nizhan.chen@gmail.com>
Cc: Marek Szyprowski <m.szyprowski@samsung.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
|
|
rb_erase_augmented() is a static function annotated with
__always_inline. This causes a compile failure when attempting to use
the rbtree implementation as a library (e.g. kvm tool):
rbtree_augmented.h:125:24: error: expected `=', `,', `;', `asm' or `__attribute__' before `void'
Include linux/compiler.h in rbtree_augmented.h so that the __always_inline
macro is resolved correctly.
Signed-off-by: Will Deacon <will.deacon@arm.com>
Cc: Pekka Enberg <penberg@kernel.org>
Reviewed-by: Michel Lespinasse <walken@google.com>
Cc: Ingo Molnar <mingo@elte.hu>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
|
|
The genalloc code uses the bitmap API from include/linux/bitmap.h and
lib/bitmap.c, which is based on long values. Both bitmap_set from
lib/bitmap.c and bitmap_set_ll, which is the lockless version from
genalloc.c, use BITMAP_LAST_WORD_MASK to set the first bits in a long in
the bitmap.
That one uses (1 << bits) - 1, 0b111, if you are setting the first three
bits. This means that the API counts from the least significant bits
(LSB from now on) to the MSB. The LSB in the first long is bit 0, then.
The same works for the lookup functions.
The genalloc code uses longs for the bitmap, as it should. In
include/linux/genalloc.h, struct gen_pool_chunk has unsigned long
bits[0] as its last member. When allocating the struct, genalloc should
reserve enough space for the bitmap. This should be a proper number of
longs that can fit the amount of bits in the bitmap.
However, genalloc allocates an integer number of bytes that fit the
amount of bits, but may not be an integer amount of longs. 9 bytes, for
example, could be allocated for 70 bits.
This is a problem in itself if the Least Significat Bit in a long is in
the byte with the largest address, which happens in Big Endian machines.
This means genalloc is not allocating the byte in which it will try to
set or check for a bit.
This may end up in memory corruption, where genalloc will try to set the
bits it has not allocated. In fact, genalloc may not set these bits
because it may find them already set, because they were not zeroed since
they were not allocated. And that's what causes a BUG when
gen_pool_destroy is called and check for any set bits.
What really happens is that genalloc uses kmalloc_node with __GFP_ZERO
on gen_pool_add_virt. With SLAB and SLUB, this means the whole slab
will be cleared, not only the requested bytes. Since struct
gen_pool_chunk has a size that is a multiple of 8, and slab sizes are
multiples of 8, we get lucky and allocate and clear the right amount of
bytes.
Hower, this is not the case with SLOB or with older code that did memset
after allocating instead of using __GFP_ZERO.
So, a simple module as this (running 3.6.0), will cause a crash when
rmmod'ed.
[root@phantom-lp2 foo]# cat foo.c
#include <linux/kernel.h>
#include <linux/module.h>
#include <linux/init.h>
#include <linux/genalloc.h>
MODULE_LICENSE("GPL");
MODULE_VERSION("0.1");
static struct gen_pool *foo_pool;
static __init int foo_init(void)
{
int ret;
foo_pool = gen_pool_create(10, -1);
if (!foo_pool)
return -ENOMEM;
ret = gen_pool_add(foo_pool, 0xa0000000, 32 << 10, -1);
if (ret) {
gen_pool_destroy(foo_pool);
return ret;
}
return 0;
}
static __exit void foo_exit(void)
{
gen_pool_destroy(foo_pool);
}
module_init(foo_init);
module_exit(foo_exit);
[root@phantom-lp2 foo]# zcat /proc/config.gz | grep SLOB
CONFIG_SLOB=y
[root@phantom-lp2 foo]# insmod ./foo.ko
[root@phantom-lp2 foo]# rmmod foo
------------[ cut here ]------------
kernel BUG at lib/genalloc.c:243!
cpu 0x4: Vector: 700 (Program Check) at [c0000000bb0e7960]
pc: c0000000003cb50c: .gen_pool_destroy+0xac/0x110
lr: c0000000003cb4fc: .gen_pool_destroy+0x9c/0x110
sp: c0000000bb0e7be0
msr: 8000000000029032
current = 0xc0000000bb0e0000
paca = 0xc000000006d30e00 softe: 0 irq_happened: 0x01
pid = 13044, comm = rmmod
kernel BUG at lib/genalloc.c:243!
[c0000000bb0e7ca0] d000000004b00020 .foo_exit+0x20/0x38 [foo]
[c0000000bb0e7d20] c0000000000dff98 .SyS_delete_module+0x1a8/0x290
[c0000000bb0e7e30] c0000000000097d4 syscall_exit+0x0/0x94
--- Exception: c00 (System Call) at 000000800753d1a0
SP (fffd0b0e640) is in userspace
Signed-off-by: Thadeu Lima de Souza Cascardo <cascardo@linux.vnet.ibm.com>
Cc: Paul Gortmaker <paul.gortmaker@windriver.com>
Cc: Benjamin Gaignard <benjamin.gaignard@stericsson.com>
Cc: <stable@vger.kernel.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
|
|
Add this missing SPI dependency and prevent the driver from building
without SPI, because functions of the spi driver are used in this
driver.
drivers/video/backlight/ili9320.c:51: undefined reference to `spi_sync'
Also, a prompt string for CONFIG_LCD_ILI9320 is added for explicit
selection.
Signed-off-by: Jingoo Han <jg1.han@samsung.com>
Cc: Richard Purdie <rpurdie@rpsys.net>
Cc: Ben Dooks <ben-linux@fluff.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
|
|
Before changing a group's default behavior to ALLOW, we must check if
its parent's behavior is also ALLOW.
Signed-off-by: Aristeu Rozanski <aris@redhat.com>
Cc: Tejun Heo <tj@kernel.org>
Cc: Li Zefan <lizefan@huawei.com>
Cc: James Morris <jmorris@namei.org>
Cc: Pavel Emelyanov <xemul@openvz.org>
Acked-by: Serge Hallyn <serge.hallyn@canonical.com>
Cc: Jiri Slaby <jslaby@suse.cz>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
|
|
Convert the code to use kstrtou32() instead of simple_strtoul() which is
deprecated. The real size of the variables are u32, so use kstrtou32
instead of kstrtoul
Signed-off-by: Aristeu Rozanski <aris@redhat.com>
Cc: Dave Jones <davej@redhat.com>
Cc: Tejun Heo <tj@kernel.org>
Cc: Li Zefan <lizefan@huawei.com>
Cc: James Morris <jmorris@namei.org>
Cc: Pavel Emelyanov <xemul@openvz.org>
Acked-by: Serge Hallyn <serge.hallyn@canonical.com>
Cc: Jiri Slaby <jslaby@suse.cz>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
|
|
This was done in a v2 patch but v1 ended up being committed. The
variable name is less confusing and stores the default behavior when no
matching exception exists.
Signed-off-by: Aristeu Rozanski <aris@redhat.com>
Cc: Dave Jones <davej@redhat.com>
Cc: Tejun Heo <tj@kernel.org>
Cc: Li Zefan <lizefan@huawei.com>
Cc: James Morris <jmorris@namei.org>
Cc: Pavel Emelyanov <xemul@openvz.org>
Acked-by: Serge Hallyn <serge.hallyn@canonical.com>
Cc: Jiri Slaby <jslaby@suse.cz>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
|
|
Commit ad676077a2ae ("device_cgroup: convert device_cgroup internally to
policy + exceptions") removed rcu locks which are needed in
task_devcgroup called in this chain:
devcgroup_inode_mknod OR __devcgroup_inode_permission ->
__devcgroup_inode_permission ->
task_devcgroup ->
task_subsys_state ->
task_subsys_state_check.
Change the code so that task_devcgroup is safely called with rcu read
lock held.
===============================
[ INFO: suspicious RCU usage. ]
3.6.0-rc5-next-20120913+ #42 Not tainted
-------------------------------
include/linux/cgroup.h:553 suspicious rcu_dereference_check() usage!
other info that might help us debug this:
rcu_scheduler_active = 1, debug_locks = 0
2 locks held by kdevtmpfs/23:
#0: (sb_writers){.+.+.+}, at: [<ffffffff8116873f>]
mnt_want_write+0x1f/0x50
#1: (&sb->s_type->i_mutex_key#3/1){+.+.+.}, at: [<ffffffff811558af>]
kern_path_create+0x7f/0x170
stack backtrace:
Pid: 23, comm: kdevtmpfs Not tainted 3.6.0-rc5-next-20120913+ #42
Call Trace:
lockdep_rcu_suspicious+0xfd/0x130
devcgroup_inode_mknod+0x19d/0x240
vfs_mknod+0x71/0xf0
handle_create.isra.2+0x72/0x200
devtmpfsd+0x114/0x140
? handle_create.isra.2+0x200/0x200
kthread+0xd6/0xe0
kernel_thread_helper+0x4/0x10
Signed-off-by: Jiri Slaby <jslaby@suse.cz>
Cc: Dave Jones <davej@redhat.com>
Cc: Tejun Heo <tj@kernel.org>
Cc: Li Zefan <lizefan@huawei.com>
Cc: James Morris <jmorris@namei.org>
Cc: Pavel Emelyanov <xemul@openvz.org>
Acked-by: Serge Hallyn <serge.hallyn@canonical.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
|
|
On s390 any write to a page (even from kernel itself) sets architecture
specific page dirty bit. Thus when a page is written to via buffered
write, HW dirty bit gets set and when we later map and unmap the page,
page_remove_rmap() finds the dirty bit and calls set_page_dirty().
Dirtying of a page which shouldn't be dirty can cause all sorts of
problems to filesystems. The bug we observed in practice is that
buffers from the page get freed, so when the page gets later marked as
dirty and writeback writes it, XFS crashes due to an assertion
BUG_ON(!PagePrivate(page)) in page_buffers() called from
xfs_count_page_state().
Similar problem can also happen when zero_user_segment() call from
xfs_vm_writepage() (or block_write_full_page() for that matter) set the
hardware dirty bit during writeback, later buffers get freed, and then
page unmapped.
Fix the issue by ignoring s390 HW dirty bit for page cache pages of
mappings with mapping_cap_account_dirty(). This is safe because for
such mappings when a page gets marked as writeable in PTE it is also
marked dirty in do_wp_page() or do_page_fault(). When the dirty bit is
cleared by clear_page_dirty_for_io(), the page gets writeprotected in
page_mkclean(). So pagecache page is writeable if and only if it is
dirty.
Thanks to Hugh Dickins for pointing out mapping has to have
mapping_cap_account_dirty() for things to work and proposing a cleaned
up variant of the patch.
The patch has survived about two hours of running fsx-linux on tmpfs
while heavily swapping and several days of running on out build machines
where the original problem was triggered.
Signed-off-by: Jan Kara <jack@suse.cz>
Cc: Martin Schwidefsky <schwidefsky@de.ibm.com>
Cc: Mel Gorman <mgorman@suse.de>
Cc: Hugh Dickins <hughd@google.com>
Cc: Heiko Carstens <heiko.carstens@de.ibm.com>
Cc: <stable@vger.kernel.org> [3.0+]
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/sarah/xhci into usb-linus
xHCI trivial fixes for 3.7
Hi Greg,
Here's four trivial xHCI bug fixes for 3.7. They clean up some issues found
while running Coverity across the xHCI driver. One is marked for stable.
Sarah Sharp
|
|
flush_old_exec() clears PF_KTHREAD but forgets about PF_NOFREEZE.
Signed-off-by: Oleg Nesterov <oleg@redhat.com>
Acked-by: Tejun Heo <tj@kernel.org>
Cc: stable@vger.kernel.org
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
|
|
Remove the variable ep_ctx from xhci_add_endpoint(), since it is
assigned but unused. Caught by Coverity.
Signed-off-by: Sarah Sharp <sarah.a.sharp@linux.intel.com>
|
|
Remove the variable slot_ctx from xhci_dbg_ctx(), since it is assigned
but unused. Caught by Coverity.
Signed-off-by: Sarah Sharp <sarah.a.sharp@linux.intel.com>
|
|
Coverity complains that xhci_evaluate_context_result() is missing a
break statement after the COMP_EBADSLT switch case. It's not a big
deal, since we wanted to return the same error code as the case
statement below it does. The end result would be one that a Slot
Disabled error completion code would also print the warning message
associated with a Context State error code. No other bad behavior would
result.
It's not worth backporting to stable kernels, since it only fixes an
issue with too much debugging.
Signed-off-by: Sarah Sharp <sarah.a.sharp@linux.intel.com>
|
|
The command cancellation code doesn't check whether find_trb_seg()
couldn't find the segment that contains the TRB to be canceled. This
could cause a NULL pointer deference later in the function when next_trb
is called. It's unlikely to happen unless something is wrong with the
command ring pointers, so add some debugging in case it happens.
This patch should be backported to stable kernels as old as 3.0, that
contain the commit b63f4053cc8aa22a98e3f9a97845afe6c15d0a0d "xHCI:
handle command after aborting the command ring".
Signed-off-by: Sarah Sharp <sarah.a.sharp@linux.intel.com>
Cc: stable@vger.kernel.org
|
|
The LPB FIFO interrupt is a peripheral interrupt, thus its L1 cell
has to be 2 instead of 3. Fix it and while at it, move the lpbfifo
node to the common dtsi file.
This patch fixes the irqdomain warning:
...
WARNING: at kernel/irq/irqdomain.c:766
Modules linked in:
NIP: c00587fc LR: c0058e0c CTR: c0014e54
REGS: c7837c10 TRAP: 0700 Tainted: G W (3.7.0-rc1-00003-g6e51414)
MSR: 00029032 <EE,ME,IR,DR,RI> CR: 82cd8322 XER: 00000000
TASK = c7834000[1] 'swapper' THREAD: c7836000
GPR00: 00000001 c7837cc0 c7834000 c7806080 000000d7 c7837d20 00000003 c7837cec
GPR08: c7837ce8 00000000 00000000 00000008 82cd3342 00000000 c0003f88 00000000
GPR16: 00000000 00000000 00000000 00000000 00000000 00000000 00000000 c7850ec0
GPR24: c782b010 00000000 00000001 c7852900 00000003 c7df5be0 c7806080 000000d7
NIP [c00587fc] irq_linear_revmap+0x2c/0x4c
LR [c0058e0c] irq_create_mapping+0x28/0x124
Reported-by: Stefan Roese <sr@denx.de>
Signed-off-by: Anatolij Gustschin <agust@denx.de>
|
|
Currently, when booting MPC52xx based platforms, we get:
mpc52xx_irqhost_map: invalid irq: virq=16, l1=0, l2=3
irq: irq-16==>hwirq-0x3 mapping failed: -22
[WARNing skipped]
The warning is wrong since the mapping itself is valid. However, there is no
support for that type of IRQ currently. Print a proper warning and bind the irq
to a no_irq chip.
Signed-off-by: Wolfram Sang <w.sang@pengutronix.de>
Cc: John Bonesio <bones@secretlab.ca>
Cc: Anatolij Gustschin <agust@denx.de>
Cc: Grant Likely <grant.likely@secretlab.ca>
Signed-off-by: Anatolij Gustschin <agust@denx.de>
|
|
Add a node for the pcm030-audio-fabric ASoC driver
Signed-off-by: Eric Millbrandt <emillbrandt@dekaresearch.com>
Signed-off-by: Anatolij Gustschin <agust@denx.de>
|
|
We BUG if we fail to commit the transaction when creating a snapshot, which
is just obnoxious. Remove the BUG_ON(). Thanks,
Signed-off-by: Josef Bacik <jbacik@fusionio.com>
|
|
My workload is a raid5 which had 16 disks. And used our filesystem to
write using direct-io mode.
I used the blktrace to find those message:
8,16 0 6647 2.453665504 2579 M W 7493152 + 8 [md0_raid5]
8,16 0 6648 2.453672411 2579 Q W 7493160 + 8 [md0_raid5]
8,16 0 6649 2.453672606 2579 M W 7493160 + 8 [md0_raid5]
8,16 0 6650 2.453679255 2579 Q W 7493168 + 8 [md0_raid5]
8,16 0 6651 2.453679441 2579 M W 7493168 + 8 [md0_raid5]
8,16 0 6652 2.453685948 2579 Q W 7493176 + 8 [md0_raid5]
8,16 0 6653 2.453686149 2579 M W 7493176 + 8 [md0_raid5]
8,16 0 6654 2.453693074 2579 Q W 7493184 + 8 [md0_raid5]
8,16 0 6655 2.453693254 2579 M W 7493184 + 8 [md0_raid5]
8,16 0 6656 2.453704290 2579 Q W 7493192 + 8 [md0_raid5]
8,16 0 6657 2.453704482 2579 M W 7493192 + 8 [md0_raid5]
8,16 0 6658 2.453715016 2579 Q W 7493200 + 8 [md0_raid5]
8,16 0 6659 2.453715247 2579 M W 7493200 + 8 [md0_raid5]
8,16 0 6660 2.453721730 2579 Q W 7493208 + 8 [md0_raid5]
8,16 0 6661 2.453721974 2579 M W 7493208 + 8 [md0_raid5]
8,16 0 6662 2.453728202 2579 Q W 7493216 + 8 [md0_raid5]
8,16 0 6663 2.453728436 2579 M W 7493216 + 8 [md0_raid5]
8,16 0 6664 2.453734782 2579 Q W 7493224 + 8 [md0_raid5]
8,16 0 6665 2.453735019 2579 M W 7493224 + 8 [md0_raid5]
8,16 0 6666 2.453741401 2579 Q W 7493232 + 8 [md0_raid5]
8,16 0 6667 2.453741632 2579 M W 7493232 + 8 [md0_raid5]
8,16 0 6668 2.453748148 2579 Q W 7493240 + 8 [md0_raid5]
8,16 0 6669 2.453748386 2579 M W 7493240 + 8 [md0_raid5]
8,16 0 6670 2.453851843 2579 I W 7493144 + 104 [md0_raid5]
8,16 0 0 2.453853661 0 m N cfq2579 insert_request
8,16 0 6671 2.453854064 2579 I W 7493120 + 24 [md0_raid5]
8,16 0 0 2.453854439 0 m N cfq2579 insert_request
8,16 0 6672 2.453854793 2579 U N [md0_raid5] 2
8,16 0 0 2.453855513 0 m N cfq2579 Not idling.st->count:1
8,16 0 0 2.453855927 0 m N cfq2579 dispatch_insert
8,16 0 0 2.453861771 0 m N cfq2579 dispatched a request
8,16 0 0 2.453862248 0 m N cfq2579 activate rq,drv=1
8,16 0 6673 2.453862332 2579 D W 7493120 + 24 [md0_raid5]
8,16 0 0 2.453865957 0 m N cfq2579 Not idling.st->count:1
8,16 0 0 2.453866269 0 m N cfq2579 dispatch_insert
8,16 0 0 2.453866707 0 m N cfq2579 dispatched a request
8,16 0 0 2.453867061 0 m N cfq2579 activate rq,drv=2
8,16 0 6674 2.453867145 2579 D W 7493144 + 104 [md0_raid5]
8,16 0 6675 2.454147608 0 C W 7493120 + 24 [0]
8,16 0 0 2.454149357 0 m N cfq2579 complete rqnoidle 0
8,16 0 6676 2.454791505 0 C W 7493144 + 104 [0]
8,16 0 0 2.454794803 0 m N cfq2579 complete rqnoidle 0
8,16 0 0 2.454795160 0 m N cfq schedule dispatch
From above messages,we can find rq[W 7493144 + 104] and rq[W
7493120 + 24] do not merge.
Because the bio order is:
8,16 0 6638 2.453619407 2579 Q W 7493144 + 8 [md0_raid5]
8,16 0 6639 2.453620460 2579 G W 7493144 + 8 [md0_raid5]
8,16 0 6640 2.453639311 2579 Q W 7493120 + 8 [md0_raid5]
8,16 0 6641 2.453639842 2579 G W 7493120 + 8 [md0_raid5]
The bio(7493144) first and bio(7493120) later.So the subsequent
bios will be divided into two parts.
When flushing plug-list,because elv_attempt_insert_merge only support
backmerge,not supporting frontmerge.
So rq[7493120 + 24] can't merge with rq[7493144 + 104].
From my test,i found those situation can count 25% in our system.
Using this patch, there is no this situation.
Signed-off-by: Jianpeng Ma <majianpeng@gmail.com>
CC:Shaohua Li <shli@kernel.org>
Signed-off-by: Jens Axboe <axboe@kernel.dk>
|
|
After cloning root's node, we forgot to dec the src's ref
which can lead to a memory leak.
Signed-off-by: Liu Bo <bo.li.liu@oracle.com>
Signed-off-by: Chris Mason <chris.mason@fusionio.com>
|
|
Per IEEE Std. 802.11-2012, Sec 8.2.4.4.1, the sequence Control field is
not present in control frames. We noticed this problem when processing
Block Ack Requests.
Cc: stable@vger.kernel.org
Signed-off-by: Javier Cardona <javier@cozybit.com>
Signed-off-by: Javier Lopez <jlopex@cozybit.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
|
|
|
|
On a really full file system I was getting ENOSPC back from
btrfs_update_inode when trying to update the parent inode when creating a
snapshot. Just use the fallback method so we can update the inode and not
have to worry about having a delayed ref. Thanks,
Signed-off-by: Josef Bacik <jbacik@fusionio.com>
|
|
This patch also requires a change in the user-space part of "receive".
We need to use "lchown" instead of "chown". We will do this in the
following patch.
Signed-off-by: Alex Lyakas <alex.btrfs@zadarastorage.com>
if (S_ISREG(sctx->cur_inode_mode)) {
|
|
Steps to reproduce:
# mkfs.btrfs -m raid1 <disk1> <disk2>
# btrfstune -S 1 <disk1>
# mount <disk1> <mnt>
# btrfs device add <disk3> <disk4> <mnt>
# mount -o remount,rw <mnt>
# dd if=/dev/zero of=<mnt>/tmpfile bs=1M count=1
Deadlock happened.
It is because of the nested chunk allocation. When we wrote the data
into the filesystem, we would allocate the data chunk because there was
no data chunk in the filesystem. At the end of the data chunk allocation,
we should insert the metadata of the data chunk into the extent tree, but
there was no raid1 chunk, so we tried to lock the chunk allocation mutex to
allocate the new chunk, but we had held the mutex, the deadlock happened.
By rights, we would allocate the raid1 chunk when we added the second device
because the profile of the seed filesystem is raid1 and we had two devices.
But we didn't do that in fact. It is because the last step of the first device
insertion didn't commit the transaction. So when we added the second device,
we didn't cow the tree, and just inserted the relative metadata into the leaves
which were generated by the first device insertion, and its profile was dup.
So, I fix this problem by commiting the transaction at the end of the first
device insertion.
Signed-off-by: Miao Xie <miaox@cn.fujitsu.com>
|
|
Currently if len argument in btrfs_ioctl_fitrim() is smaller than
one FSB we will continue and finally return 0 bytes discarded.
However if the length to discard is smaller then file system block
we should really return EINVAL.
Signed-off-by: Lukas Czerner <lczerner@redhat.com>
|
|
We should free quota_root before returning from the error
handling code.
Signed-off-by: Tsutomu Itoh <t-itoh@jp.fujitsu.com>
|
|
When sending a device file, the stream was missing the mode. Also the
rdev was encoded wrongly.
Signed-off-by: Arne Jansen <sensille@gmx.net>
|
|
This adds support for the new extended inode refs to btrfs send.
Signed-off-by: Jan Schmidt <list.btrfs@jan-o-sch.net>
|
|
gcc says "warning: comparison of unsigned expression >= 0 is always
true" because i is an unsigned long. And gcc is right this time.
Signed-off-by: Stefan Behrens <sbehrens@giantdisaster.de>
|
|
To see the problem, create many hardlinks to the same file (120 should do it),
then look up paths by inode with:
ls -i
btrfs inspect inode-resolve -v $ino /mnt/btrfs
I noticed the memory layout of the fspath->val data had some irregularities
(some unnecessary gaps that stop appearing about halfway),
so I'm not sure there aren't any bugs left in it.
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/broonie/sound into for-linus
ASoC: Fixes for v3.7
A couple of driver fixes, one that improves the interoperability of
WM8994 with controllers that are sensitive to extra BCLK cycles and some
build break fixes for ux500.
|
|
CONFIG_PM_SLEEP
This will fix warnings like following when CONFIG_PM_SLEEP is not set:
warning: 'xxx_suspend' defined but not used [-Wunused-function]
warning: 'xxx_resume' defined but not used [-Wunused-function]
Because
SET_SYSTEM_SLEEP_PM_OPS(suspend_fn, resume_fn)
Only references the callbacks on CONFIG_PM_SLEEP (instead of CONFIG_PM).
Cc: Mattia Dongili <malattia@linux.it>
Cc: Arnd Bergmann <arnd@arndb.de>
Cc: platform-driver-x86@vger.kernel.org
Signed-off-by: Yuanhan Liu <yuanhan.liu@linux.intel.com>
Signed-off-by: Fengguang Wu <fengguang.wu@intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
This is a Chinese translated version of
Documentation/arm64/memory.txt
Signed-off-by: Fu Wei <tekkamanninja@gmail.com>
Acked-by: Catalin Marinas <catalin.marinas@arm.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
This is a Chinese translated version of
Documentation/arm64/booting.txt
Signed-off-by: Fu Wei <tekkamanninja@gmail.com>
Acked-by: Catalin Marinas <catalin.marinas@arm.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
This is a Chinese translated version of
Documentation/IRQ.txt
Signed-off-by: Fu Wei <tekkamanninja@gmail.com>
Acked-by: Harry Wei <harryxiyou@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
This patch adds description on recently introduced direct firmware
loading by Linus.
Cc: Linus Torvalds <torvalds@linux-foundation.org>
Signed-off-by: Ming Lei <ming.lei@canonical.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
Board name changed on another shipping Lucid tablet.
Signed-off-by: Anisse Astier <anisse@astier.eu>
Cc: <stable@vger.kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
BIOS vendors keep changing the BIOS versions. Only match the beginning
of the string to match all Lucid tablets with board name M11JB.
Signed-off-by: Anisse Astier <anisse@astier.eu>
Cc: <stable@vger.kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
Remove the const keyword from the V4L2 subdev events operations to match
the V4L2 API.
Signed-off-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Acked-by: Sakari Ailus <sakari.ailus@iki.fi>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
|
|
Commit 4f996594 ("v4l2: make vidioc_s_crop const") modified the
vidioc_s_crop operation prototype but forgot to update the OMAP3 ISP
driver. Add a const keyword to fix the function prototype.
Signed-off-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Acked-by: Sakari Ailus <sakari.ailus@iki.fi>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
|
|
stv0900_set_mclk()
The dereference should be moved below the NULL test.
dpatch engine is used to auto generate this patch.
(https://github.com/weiyj/dpatch)
Signed-off-by: Wei Yongjun <yongjun_wei@trendmicro.com.cn>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
|
|
Remove temporary do-while(0) loop used to keep changes minimal.
Fixup indentation, remove some line breaks, and replace break with goto
to maintain flow.
Signed-off-by: Johan Hovold <jhovold@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
Fix port-data memory leak by moving port data allocation and
deallocation to port_probe and port_remove.
Since commit 0998d0631001288 (device-core: Ensure drvdata = NULL when no
driver is bound) the port private data is no longer freed at release as
it is no longer accessible.
Note that the indentation was kept intact using a do-while(0) in order
to facilitate review. A follow-up patch will remove it.
Compile-only tested.
Signed-off-by: Johan Hovold <jhovold@gmail.com>
Cc: stable <stable@vger.kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
Remove private zombie flag used to signal disconnect and to prevent
control urb from being submitted from interrupt urb completion handler.
The control urb will not be re-submitted as both the control urb and the
interrupt urb is killed on disconnect.
Signed-off-by: Johan Hovold <jhovold@gmail.com>
Cc: stable <stable@vger.kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
