Age | Commit message (Collapse) | Author |
|
master.kernel.org:/pub/scm/linux/kernel/git/jgarzik/netdev-2.6
|
|
I tried to group recovery related fields nearby (non-CA_Open related
variables, to be more accurate) so that one to three cachelines would
not be necessary in CA_Open. These are now contiguously deployed:
struct sk_buff_head out_of_order_queue; /* 1968 80 */
/* --- cacheline 32 boundary (2048 bytes) --- */
struct tcp_sack_block duplicate_sack[1]; /* 2048 8 */
struct tcp_sack_block selective_acks[4]; /* 2056 32 */
struct tcp_sack_block recv_sack_cache[4]; /* 2088 32 */
/* --- cacheline 33 boundary (2112 bytes) was 8 bytes ago --- */
struct sk_buff * highest_sack; /* 2120 8 */
int lost_cnt_hint; /* 2128 4 */
int retransmit_cnt_hint; /* 2132 4 */
u32 lost_retrans_low; /* 2136 4 */
u8 reordering; /* 2140 1 */
u8 keepalive_probes; /* 2141 1 */
/* XXX 2 bytes hole, try to pack */
u32 prior_ssthresh; /* 2144 4 */
u32 high_seq; /* 2148 4 */
u32 retrans_stamp; /* 2152 4 */
u32 undo_marker; /* 2156 4 */
int undo_retrans; /* 2160 4 */
u32 total_retrans; /* 2164 4 */
...and they're then followed by URG slowpath & keepalive related
variables.
Head of the out_of_order_queue always needed for empty checks, if
that's empty (and TCP is in CA_Open), following ~200 bytes (in 64-bit)
shouldn't be necessary for anything. If only OFO queue exists but TCP
is in CA_Open, selective_acks (and possibly duplicate_sack) are
necessary besides the out_of_order_queue but the rest of the block
again shouldn't be (ie., the other direction had losses).
As the cacheline boundaries depend on many factors in the preceeding
stuff, trying to align considering them doesn't make too much sense.
Commented one ordering hazard.
There are number of low utilized u8/16s that could be combined get 2
bytes less in total so that the hole could be made to vanish (includes
at least ecn_flags, urg_data, urg_mode, frto_counter, nonagle).
Signed-off-by: Ilpo Järvinen <ilpo.jarvinen@helsinki.fi>
Acked-by: Eric Dumazet <dada1@cosmosbay.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
This patch increments the version to 3.93.
Signed-off-by: Matt Carlson <mcarlson@broadcom.com>
Signed-off-by: Michael Chan <mchan@broadcom.com>
Signed-off-by: Benjamin Li <benli@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
This patch adds some options obtained through shared memory.
Signed-off-by: Matt Carlson <mcarlson@broadcom.com>
Signed-off-by: Michael Chan <mchan@broadcom.com>
Signed-off-by: Benjamin Li <benli@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
This patch added the 5785 device ID and ASIC revision to the code.
Signed-off-by: Matt Carlson <mcarlson@broadcom.com>
Signed-off-by: Michael Chan <mchan@broadcom.com>
Signed-off-by: Benjamin Li <benli@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
This patch introduces the libphy support.
Signed-off-by: Matt Carlson <mcarlson@broadcom.com>
Signed-off-by: Michael Chan <mchan@broadcom.com>
Signed-off-by: Benjamin Li <benli@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
This patch introduces code to register and unregister the tg3 mdio bus
with the system.
Signed-off-by: Matt Carlson <mcarlson@broadcom.com>
Signed-off-by: Michael Chan <mchan@broadcom.com>
Signed-off-by: Benjamin Li <benli@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
This patch introduces the TG3_FLG3_USE_PHYLIB flag and applies it to
some select places. This work makes later patches a little easier to
read.
Signed-off-by: Matt Carlson <mcarlson@broadcom.com>
Signed-off-by: Michael Chan <mchan@broadcom.com>
Signed-off-by: Benjamin Li <benli@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
This patch applies cleanups that would otherwise clutter later
patches.
Signed-off-by: Matt Carlson <mcarlson@broadcom.com>
Signed-off-by: Michael Chan <mchan@broadcom.com>
Signed-off-by: Benjamin Li <benli@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
This patch moves some functions towards the top of the file to avoid
unnecessary function prototypes.
Signed-off-by: Matt Carlson <mcarlson@broadcom.com>
Signed-off-by: Michael Chan <mchan@broadcom.com>
Signed-off-by: Benjamin Li <benli@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Signed-off-by: Alan Cox <alan@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Signed-off-by: Alan Cox <alan@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
I've pushed it down as far as I dare at this point. Someone familiar with
the internal PPP semantics can probably push it further. Another step to
eliminating the old BKL ioctl usage.
Signed-off-by: Alan Cox <alan@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
master.kernel.org:/pub/scm/linux/kernel/git/davem/net-2.6
Conflicts:
drivers/net/cpmac.c
net/mac80211/mlme.c
|
|
Herbert Xu points out that the use of seperate feature bits for features
to be propagated to VLAN devices is going to get messy real soon.
Replace the VLAN feature bits by a bitmask of feature flags to be
propagated and restore the old GSO_SHIFT/MASK values.
Signed-off-by: Patrick McHardy <kaber@trash.net>
Acked-by: Herbert Xu <herbert@gondor.apana.org.au>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
master.kernel.org:/pub/scm/linux/kernel/git/jgarzik/netdev-2.6
|
|
Use memmove to handle overlapping copy of data.
Signed-off-by: Stephen Hemminger <shemminger@vyatta.com>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
|
|
Use netdev_alloc_skb for rx buffer allocation. This sets skb->dev
and can be overriden for NUMA machines.
Change code to return new buffer rather than call by reference.
Signed-off-by: Stephen Hemminger <shemminger@vyatta.com>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
|
|
Use netdev_alloc_skb. This sets skb->dev and allows arch specific
allocation.
Signed-off-by: Stephen Hemminger <shemminger@vyatta.com>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
|
|
Use netdev_alloc_skb. This sets skb->dev and allows arch specific
allocation.
Remove dead code and dead comments.
Signed-off-by: Stephen Hemminger <shemminger@vyatta.com>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
|
|
Use netdev_alloc_skb. This sets skb->dev and allows arch specific
allocation.
Signed-off-by: Stephen Hemminger <shemminger@vyatta.com>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
|
|
Use netdev_alloc_skb. This sets skb->dev and allows arch specific
allocation. Also simplify and cleanup the alignment code.
Signed-off-by: Maciej W. Rozycki <macro@linux-mips.org>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
|
|
Use netdev_alloc_skb for rx buffer allocation. This sets skb->dev
and can be overriden for NUMA machines.
Signed-off-by: Stephen Hemminger <shemminger@vyatta.com>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
|
|
Remove extraneous semicolons after switch and conditional statements.
Signed-off-by: Stephen Hemminger <shemminger@vyatta.com>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
|
|
fmvj18x_cs: The manfid of "NextCom NC5310 rev B" is MANF_ID_FUJITSU.
but this card is MBH10302 based card.
use ConfigBase to detect the cardtype for this card.
Signed-off-by: Komuro <komurojun-mbn@nifty.com>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
|
|
keep bit7,8 of XIRCREG42_SWC1 in set_multicast_list.
Signed-off-by: Komuro <komurojun-mbn@nifty.com>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
|
|
If alloc_skb failed, the recieved packet will be dropped. Do not increase
rx_bytes for dropped packet.
Signed-off-by: Wang Chen <wangchen@cn.fujitsu.com>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
|
|
Use standard routine for queue purging.
Signed-off-by: Wang Chen <wangchen@cn.fujitsu.com>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
|
|
Use standard routine for queue purging.
Signed-off-by: Wang Chen <wangchen@cn.fujitsu.com>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
|
|
Commit cac1f3c8 factored out the code for get_phy_id so that it
could be reused in multiple places. Turns out that some of the
users can be modular, so we need to export this symbol as well.
Signed-off-by: Paul Gortmaker <paul.gortmaker@windriver.com>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
|
|
The purpose of nla_parse_nested_compat() is to parse attributes which
contain a struct followed by a stream of nested attributes. So far,
it called nla_parse_nested() to parse the stream of nested attributes
which was wrong, as nla_parse_nested() expects a container attribute
as data which holds the attribute stream. It needs to call
nla_parse() directly while pointing at the next possible alignment
point after the struct in the beginning of the attribute.
With this patch, I can no longer reproduce the reported leftover
warnings.
Signed-off-by: Thomas Graf <tgraf@suug.ch>
Acked-by: Patrick McHardy <kaber@trash.net>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
3c515.c uses pnp_irq(), which calls pnp_get_resource(),
which is not defined when CONFIG_PNP=n, so in that case,
get the IRQ from a hardware register.
3c515.c:(.text+0x3adc0): undefined reference to `pnp_get_resource'
Signed-off-by: Randy Dunlap <randy.dunlap@oracle.com>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
|
|
Add Broadcom PHYs supported missing from the description.
Signed-off-by: Maciej W. Rozycki <macro@linux-mips.org>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
|
|
Configure the BCM5482S secondary SerDes for 1000Base-X mode when the
appropriate dev_flags are passed in to phy_connect(). This is
needed when the PHY is used for fiber and backplane connections.
Signed-off-by: Nate Case <ncase@xes-inc.com>
Signed-off-by: Maciej W. Rozycki <macro@linux-mips.org>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
|
|
Add a "follow" selection for fail_over_mac. This option
causes the MAC address to move from slave to slave as the active
slave changes. This is in addition to the existing fail_over_mac option
that causes the bond's MAC address to change during failover.
This new option is useful for devices that cannot tolerate
multiple ports using the same MAC address simultaneously, either
because it confuses them or incurs a performance penalty (as is the
case with some LPAR-aware multiport devices). Because the MAC of the
bond itself does not change, the "follow" option is slightly more
reliable during failover and doesn't change the MAC of the bond during
operation.
This patch requires a previous ARP monitor change to properly
handle RTNL during failovers.
Signed-off-by: Jay Vosburgh <fubar@us.ibm.com>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
|
|
Refactor ARP monitor for active-backup mode. The motivation for
this is to take care of locking issues in a clear manner (particularly to
correctly handle RTNL vs. the bonding locks). Currently, the a-b ARP
monitor does not hold RTNL at all, but future changes will require RTNL
during ARP monitor failovers.
Rather than using conditional locking, this patch instead breaks
up the ARP monitor into three discrete steps: inspection, commit changes,
and probe. The inspection phase marks slaves that require link state
changes. The commit phase is only called if inspection detects that
changes are needed, and is called with RTNL. Lastly, the probe phase
issues the ARP probes that the inspection phase uses to determine link
state.
Signed-off-by: Jay Vosburgh <fubar@us.ibm.com>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
|
|
With IPoIB, reception of gratuitous ARP by neighboring hosts
is essential for a successful change of slaves in case of failure.
Otherwise, they won't learn about the HW address change and need
to wait a long time until the neighboring system gives up and sends
an ARP request to learn the new HW address. This patch decreases
the chance for a lost of a gratuitous ARP packet by sending it more
than once. The number retries is configurable and can be set with a
module param.
Signed-off-by: Moni Shoua <monis@voltaire.com>
Acked-by: Jay Vosburgh <fubar@us.ibm.com>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
|
|
Some places iterate over the checked list right after the check
itself, so even if the list is empty, the list_for_each_xxx
iterator will make everything right by himself.
Signed-off-by: Pavel Emelyanov <xemul@openvz.org>
Acked-by: Jay Vosburgh <fubar@us.ibm.com>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
|
|
Many places either do not modify the list under the list_for_each_xxx,
or break out of the loop as soon as the first element is removed.
Thus, this _safe iteration just occupies some unneeded .text space
and requires an additional variable.
Signed-off-by: Pavel Emelyanov <xemul@openvz.org>
Acked-by: Jay Vosburgh <fubar@us.ibm.com>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
|
|
While we're fixing the bond_create, I hope it's OK to polish it
a bit after the fixes.
The third argument is NULL at the first caller and is ignored by
the second one, so remove it.
Signed-off-by: Pavel Emelyanov <xemul@openvz.org>
Acked-by: Jay Vosburgh <fubar@us.ibm.com>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
|
|
Remove bond_has_ip and all references to it. With this change,
the ARP monitor will always send ARP probes if the master is up and has
at least one slave. If the bond has an IP address, it is used in the
ARP probe; if not, the probes are sent with all zeros in the sender's
IP address (which is consistent with an RFC 2131 4.4.1 duplicate address
probe).
This is useful for cases when bonding itself is hidden underneath
a layer of virtual devices, e.g., with Xen.
Change suggested by Tsutomu Fujii <t-fujii@nb.jp.nec.com>, who
included a one-line patch that only affected active-backup mode.
Signed-off-by: Jay Vosburgh <fubar@us.ibm.com>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
|
|
Convert bonding to use msecs_to_jiffies instead of doing the
math. For the ARP monitor, there was an underflow problem that could
result in an infinite loop. The miimon already had that worked around,
but this is cleaner.
Originally by Nicolas de Pesloüan <nicolas.2p.debian@free.fr>
Jay Vosburgh corrected a math error in the original; Nicolas' original
commit message is:
When setting arp_interval parameter to a very low value, delta_in_ticks
for next arp might become 0, causing an infinite loop.
See http://bugzilla.kernel.org/show_bug.cgi?id=10680
Same problem for miimon parameter already fixed, but fix might be
enhanced, by using msecs_to_jiffies() function.
Signed-off-by: Nicolas de Pesloüan <nicolas.2p.debian@free.fr>
Signed-off-by: Jay Vosburgh <fubar@us.ibm.com>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
|
|
Signed-off-by: Al Viro <viro@zeniv.linux.org.uk>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
|
|
Add LRO support.
Signed-off-by: Divy Le Ray <divy@chelsio.com>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
|
|
Add page support to Jumbo frame Rx queues.
Signed-off-by: Divy Le Ray <divy@chelsio.com>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
|
|
Take potential dma mapping errors in account.
Signed-off-by: Divy Le Ray <divy@chelsio.com>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
|
|
WAN: protect protocol list in hdlc.c with RTNL.
Signed-off-by: Krzysztof Hałasa <khc@pm.waw.pl>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
|
|
The following code appears in the function fs_init_instance in the file drivers/net/fs_enet/fs_enet-main.c.
if (fep->ops == NULL) {
printk(KERN_ERR DRV_MODULE_NAME
": %s No matching ops found (%d).\n",
ndev->name, fpi->fs_no);
err = -EINVAL;
goto err;
}
This code implies that at the point of err, fep->ops can be NULL, so an
extra test is needed before dereferencing this value.
This problem was found using the following semantic match
(http://www.emn.fr/x-info/coccinelle/)
// <smpl>
@@
expression E, E1;
identifier f;
statement S1,S2,S3;
@@
* if (E == NULL)
{
... when != if (E == NULL) S1 else S2
when != E = E1
* E->f
... when any
return ...;
}
else S3
// </smpl>
Signed-off-by: Julia Lawall <julia@diku.dk>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
|
|
- Updated version number
Signed-off-by: Sreenivasa Honnur <sreenivasa.honnur@neterion.com>
Signed-off-by: Ramkrishna Vepa <ram.vepa@neterion.com>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
|