| Age | Commit message (Collapse) | Author |
|---|
|
If two drivers are probing devices at the same time, both will write
their match table result to the dev->of_match cache at the same time.
Only write the result if the device matches.
In a thread titled "SBus devices sometimes detected, sometimes not",
Meelis reported his SBus hme was not detected about 50% of the time.
From the debug suggested by Grant it was obvious another driver matched
some devices between the call to match the hme and the hme discovery
failling.
Reported-by: Meelis Roos <mroos@linux.ee>
Signed-off-by: Milton Miller <miltonm@bga.com>
[grant.likely: modified to only call of_match_device() once]
Signed-off-by: Grant Likely <grant.likely@secretlab.ca>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/mchehab/linux-2.6
* 'v4l_for_linus' of git://git.kernel.org/pub/scm/linux/kernel/git/mchehab/linux-2.6:
[media] V4L: soc-camera: regression fix: calculate .sizeimage in soc_camera.c
[media] v4l2-subdev: fix broken subdev control enumeration
[media] Fix cx88 remote control input
[media] v4l: Release module if subdev registration fails
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/tip/linux-2.6-tip
* 'x86-fixes-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/linux-2.6-tip:
x86, AMD: Fix ARAT feature setting again
Revert "x86, AMD: Fix APIC timer erratum 400 affecting K8 Rev.A-E processors"
x86, apic: Fix spurious error interrupts triggering on all non-boot APs
x86, mce, AMD: Fix leaving freed data in a list
x86: Fix UV BAU for non-consecutive nasids
x86, UV: Fix NMI handler for UV platforms
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/tip/linux-2.6-tip
* 'perf-fixes-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/linux-2.6-tip:
perf evlist: Fix per thread mmap setup
perf tools: Honour the cpu list parameter when also monitoring a thread list
kprobes, x86: Disable irqs during optimized callback
|
|
* git://git.kernel.org/pub/scm/linux/kernel/git/sfrench/cifs-2.6:
cifs: fix cifsConvertToUCS() for the mapchars case
cifs: add fallback in is_path_accessible for old servers
|
|
Provide a stub for proc_mkdir_mode() when CONFIG_PROC_FS is not
enabled, just like the stub for proc_mkdir().
Fixes this linux-next build error:
drivers/net/wireless/airo.c:4504: error: implicit declaration of function 'proc_mkdir_mode'
Signed-off-by: Randy Dunlap <randy.dunlap@oracle.com>
Cc: Stephen Rothwell <sfr@canb.auug.org.au>
Cc: Alexey Dobriyan <adobriyan@gmail.com>
Cc: "John W. Linville" <linville@tuxdriver.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
|
|
os_dump_core() uses abort() to terminate UML in case of an fatal error.
glibc's abort() calls raise(SIGABRT) which makes use of tgkill().
tgkill() has no effect within UML's kernel threads because they are not
pthreads. As fallback abort() executes an invalid instruction to
terminate the process. Therefore UML gets killed by SIGSEGV and leaves a
ugly log entry in the host's kernel ring buffer.
To get rid of this we use our own abort routine.
Signed-off-by: Richard Weinberger <richard@nod.at>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
|
|
ZONE_CONGESTED should be a state of global memory reclaim. If not, a busy
memcg sets this and give unnecessary throttoling in wait_iff_congested()
against memory recalim in other contexts. This makes system performance
bad.
I'll think about "memcg is congested!" flag is required or not, later.
But this fix is required first.
Signed-off-by: KAMEZAWA Hiroyuki <kamezawa.hiroyu@jp.fujitsu.com>
Reviewed-by: Minchan Kim <minchan.kim@gmail.com>
Cc: Daisuke Nishimura <nishimura@mxp.nes.nec.co.jp>
Acked-by: Ying Han <yinghan@google.com>
Cc: Balbir Singh <balbir@in.ibm.com>
Cc: Johannes Weiner <jweiner@redhat.com>
Cc: Michal Hocko <mhocko@suse.cz>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
|
|
Adding the necessary MODULE_DEVICE_TABLE() information allows the driver
to be automatically loaded by udev.
Signed-off-by: Axel Lin <axel.lin@gmail.com>
Cc: Shreshtha Kumar SAHU <shreshthakumar.sahu@stericsson.com>
Cc: Richard Purdie <rpurdie@rpsys.net>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
|
|
Fix switch initialization to ensure that all switches have default routing
disabled. This guarantees that no unexpected RapidIO packets arrive to
the default port set by reset and there is no default routing destination
until it is properly configured by software.
This update also unifies handling of unmapped destinations by tsi57x, IDT
Gen1 and IDT Gen2 switches.
Signed-off-by: Alexandre Bounine <alexandre.bounine@idt.com>
Cc: Kumar Gala <galak@kernel.crashing.org>
Cc: Matt Porter <mporter@kernel.crashing.org>
Cc: Li Yang <leoli@freescale.com>
Cc: Thomas Moll <thomas.moll@sysgo.com>
Cc: <stable@kernel.org> [2.6.37+]
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
|
|
As Metze pointed out, commit 84cdf74e broke mapchars option:
Commit "cifs: fix unaligned accesses in cifsConvertToUCS"
(84cdf74e8096a10dd6acbb870dd404b92f07a756) does multiple steps
in just one commit (moving the function and changing it without
testing).
put_unaligned_le16(temp, &target[j]); is never called for any
codepoint the goes via the 'default' switch statement. As a result
we put just zero (or maybe uninitialized) bytes into the target
buffer.
His proposed patch looks correct, but doesn't apply to the current head
of the tree. This patch should also fix it.
Cc: <stable@kernel.org> # .38.x: 581ade4: cifs: clean up various nits in unicode routines (try #2)
Reported-by: Stefan Metzmacher <metze@samba.org>
Signed-off-by: Jeff Layton <jlayton@redhat.com>
Signed-off-by: Steve French <sfrench@us.ibm.com>
|
|
The is_path_accessible check uses a QPathInfo call, which isn't
supported by ancient win9x era servers. Fall back to an older
SMBQueryInfo call if it fails with the magic error codes.
Cc: stable@kernel.org
Reported-and-Tested-by: Sandro Bonazzola <sandro.bonazzola@gmail.com>
Signed-off-by: Jeff Layton <jlayton@redhat.com>
Signed-off-by: Steve French <sfrench@us.ibm.com>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/tip/linux-2.6-tip
* 'timers-fixes-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/linux-2.6-tip:
tick: Clear broadcast active bit when switching to oneshot
rtc: mc13xxx: Don't call rtc_device_register while holding lock
rtc: rp5c01: Initialize drvdata before registering device
rtc: pcap: Initialize drvdata before registering device
rtc: msm6242: Initialize drvdata before registering device
rtc: max8998: Initialize drvdata before registering device
rtc: max8925: Initialize drvdata before registering device
rtc: m41t80: Initialize clientdata before registering device
rtc: ds1286: Initialize drvdata before registering device
rtc: ep93xx: Initialize drvdata before registering device
rtc: davinci: Initialize drvdata before registering device
rtc: mxc: Initialize drvdata before registering device
clocksource: Install completely before selecting
|
|
Trying to enable the local APIC timer on early K8 revisions
uncovers a number of other issues with it, in conjunction with
the C1E enter path on AMD. Fixing those causes much more churn
and troubles than the benefit of using that timer brings so
don't enable it on K8 at all, falling back to the original
functionality the kernel had wrt to that.
Reported-and-bisected-by: Nick Bowler <nbowler@elliptictech.com>
Cc: Boris Ostrovsky <Boris.Ostrovsky@amd.com>
Cc: Andreas Herrmann <andreas.herrmann3@amd.com>
Cc: Greg Kroah-Hartman <greg@kroah.com>
Cc: Hans Rosenfeld <hans.rosenfeld@amd.com>
Cc: Nick Bowler <nbowler@elliptictech.com>
Cc: Joerg-Volker-Peetz <jvpeetz@web.de>
Signed-off-by: Borislav Petkov <borislav.petkov@amd.com>
Link: http://lkml.kernel.org/r/1305636919-31165-3-git-send-email-bp@amd64.org
Signed-off-by: Ingo Molnar <mingo@elte.hu>
|
|
This reverts commit e20a2d205c05cef6b5783df339a7d54adeb50962, as it crashes
certain boxes with specific AMD CPU models.
Moving the lower endpoint of the Erratum 400 check to accomodate
earlier K8 revisions (A-E) opens a can of worms which is simply
not worth to fix properly by tweaking the errata checking
framework:
* missing IntPenging MSR on revisions < CG cause #GP:
http://marc.info/?l=linux-kernel&m=130541471818831
* makes earlier revisions use the LAPIC timer instead of the C1E
idle routine which switches to HPET, thus not waking up in
deeper C-states:
http://lkml.org/lkml/2011/4/24/20
Therefore, leave the original boundary starting with K8-revF.
Signed-off-by: Ingo Molnar <mingo@elte.hu>
|
|
* git://git.kernel.org/pub/scm/linux/kernel/git/davem/net-2.6:
net: Change netdev_fix_features messages loglevel
vmxnet3: Fix inconsistent LRO state after initialization
sfc: Fix oops in register dump after mapping change
IPVS: fix netns if reading ip_vs_* procfs entries
bridge: fix forwarding of IPv6
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/cjb/mmc
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/cjb/mmc:
Revert "mmc: fix a race between card-detect rescan and clock-gate work instances"
|
|
Fix new kernel-doc warning in mm/page_alloc.c:
Warning(mm/page_alloc.c:2370): No description found for parameter 'nid'
Signed-off-by: Randy Dunlap <randy.dunlap@oracle.com>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
|
|
During pci remove/rescan testing found:
pci 0000:c0:03.0: PCI bridge to [bus c4-c9]
pci 0000:c0:03.0: bridge window [io 0x1000-0x0fff]
pci 0000:c0:03.0: bridge window [mem 0xf0000000-0xf00fffff]
pci 0000:c0:03.0: bridge window [mem 0xfc180000000-0xfc197ffffff 64bit pref]
pci 0000:c0:03.0: device not available (can't reserve [io 0x1000-0x0fff])
pci 0000:c0:03.0: Error enabling bridge (-22), continuing
pci 0000:c0:03.0: enabling bus mastering
pci 0000:c0:03.0: setting latency timer to 64
pcieport 0000:c0:03.0: device not available (can't reserve [io 0x1000-0x0fff])
pcieport: probe of 0000:c0:03.0 failed with error -22
This bug was caused by commit c8adf9a3e873 ("PCI: pre-allocate
additional resources to devices only after successful allocation of
essential resources.")
After that commit, pci_hotplug_io_size is changed to additional_io_size
from minium size. So it will not go through resource_size(res) != 0
path, and will not be reset.
The root cause is: pci_bridge_check_ranges will set RESOURCE_IO flag for
pci bridge, and later if children do not need IO resource. those bridge
resources will not need to be allocated. but flags is still there.
that will confuse the the pci_enable_bridges later.
related code:
static void assign_requested_resources_sorted(struct resource_list *head,
struct resource_list_x *fail_head)
{
struct resource *res;
struct resource_list *list;
int idx;
for (list = head->next; list; list = list->next) {
res = list->res;
idx = res - &list->dev->resource[0];
if (resource_size(res) && pci_assign_resource(list->dev, idx)) {
...
reset_resource(res);
}
}
}
At last, We have to clear the flags in pbus_size_mem/io when requested
size == 0 and !add_head. becasue this case it will not go through
adjust_resources_sorted().
Just make size1 = size0 when !add_head. it will make flags get cleared.
At the same time when requested size == 0, add_size != 0, will still
have in head and add_list. because we do not clear the flags for it.
After this, we will get right result:
pci 0000:c0:03.0: PCI bridge to [bus c4-c9]
pci 0000:c0:03.0: bridge window [io disabled]
pci 0000:c0:03.0: bridge window [mem 0xf0000000-0xf00fffff]
pci 0000:c0:03.0: bridge window [mem 0xfc180000000-0xfc197ffffff 64bit pref]
pci 0000:c0:03.0: enabling bus mastering
pci 0000:c0:03.0: setting latency timer to 64
pcieport 0000:c0:03.0: setting latency timer to 64
pcieport 0000:c0:03.0: irq 160 for MSI/MSI-X
pcieport 0000:c0:03.0: Signaling PME through PCIe PME interrupt
pci 0000:c4:00.0: Signaling PME through PCIe PME interrupt
pcie_pme 0000:c0:03.0:pcie01: service driver pcie_pme loaded
aer 0000:c0:03.0:pcie02: service driver aer loaded
pciehp 0000:c0:03.0:pcie04: Hotplug Controller:
v3: more simple fix. also fix one typo in pbus_size_mem
Signed-off-by: Yinghai Lu <yinghai@kernel.org>
Reviewed-by: Ram Pai <linuxram@us.ibm.com>
Cc: Jesse Barnes <jbarnes@virtuousgeek.org>
Cc: Bjorn Helgaas <bhelgaas@google.com>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
|
|
The first cpu which switches from periodic to oneshot mode switches
also the broadcast device into oneshot mode. The broadcast device
serves as a backup for per cpu timers which stop in deeper
C-states. To avoid starvation of the cpus which might be in idle and
depend on broadcast mode it marks the other cpus as broadcast active
and sets the brodcast expiry value of those cpus to the next tick.
The oneshot mode broadcast bit for the other cpus is sticky and gets
only cleared when those cpus exit idle. If a cpu was not idle while
the bit got set in consequence the bit prevents that the broadcast
device is armed on behalf of that cpu when it enters idle for the
first time after it switched to oneshot mode.
In most cases that goes unnoticed as one of the other cpus has usually
a timer pending which keeps the broadcast device armed with a short
timeout. Now if the only cpu which has a short timer active has the
bit set then the broadcast device will not be armed on behalf of that
cpu and will fire way after the expected timer expiry. In the case of
Christians bug report it took ~145 seconds which is about half of the
wrap around time of HPET (the limit for that device) due to the fact
that all other cpus had no timers armed which expired before the 145
seconds timeframe.
The solution is simply to clear the broadcast active bit
unconditionally when a cpu switches to oneshot mode after the first
cpu switched the broadcast device over. It's not idle at that point
otherwise it would not be executing that code.
[ I fundamentally hate that broadcast crap. Why the heck thought some
folks that when going into deep idle it's a brilliant concept to
switch off the last device which brings the cpu back from that
state? ]
Thanks to Christian for providing all the valuable debug information!
Reported-and-tested-by: Christian Hoffmann <email@christianhoffmann.info>
Cc: John Stultz <johnstul@us.ibm.com>
Link: http://lkml.kernel.org/r/%3Calpine.LFD.2.02.1105161105170.3078%40ionos%3E
Cc: stable@kernel.org
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
|
|
Those reduced to DEBUG can possibly be triggered by unprivileged processes
and are nothing exceptional. Illegal checksum combinations can only be
caused by driver bug, so promote those messages to WARN.
Since GSO without SG will now only cause DEBUG message from
netdev_fix_features(), remove the workaround from register_netdevice().
Signed-off-by: Michał Mirosław <mirq-linux@rere.qmqm.pl>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
During initialization of vmxnet3, the state of LRO
gets out of sync with netdev->features.
This leads to very poor TCP performance in a IP forwarding
setup and is hitting many VMware users.
Simplified call sequence:
1. vmxnet3_declare_features() initializes "adapter->lro" to true.
2. The kernel automatically disables LRO if IP forwarding is enabled,
so vmxnet3_set_flags() gets called. This also updates netdev->features.
3. Now vmxnet3_setup_driver_shared() is called. "adapter->lro" is still
set to true and LRO gets enabled again, even though
netdev->features shows it's disabled.
Fix it by updating "adapter->lro", too.
The private vmxnet3 adapter flags are scheduled for removal
in net-next, see commit a0d2730c9571aeba793cb5d3009094ee1d8fda35
"net: vmxnet3: convert to hw_features".
Patch applies to 2.6.37 / 2.6.38 and 2.6.39-rc6.
Please CC: comments.
Signed-off-by: Thomas Jarosch <thomas.jarosch@intra2net.com>
Acked-by: Stephen Hemminger <shemminger@vyatta.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Commit 747df2258b1b9a2e25929ef496262c339c380009 ('sfc: Always map MCDI
shared memory as uncacheable') introduced a separate mapping for the
MCDI shared memory (MC_TREG_SMEM). This means we can no longer easily
include it in the register dump. Since it is not particularly useful
in debugging, substitute a recognisable dummy value.
Signed-off-by: Ben Hutchings <bhutchings@solarflare.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/tmlind/linux-omap-2.6
* 'omap-fixes-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tmlind/linux-omap-2.6:
OMAP3: set the core dpll clk rate in its set_rate function
omap: iommu: Return IRQ_HANDLED in fault handler when no fault occured
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/airlied/drm-2.6
* 'drm-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/airlied/drm-2.6:
drm: Take lock around probes for drm_fb_helper_hotplug_event
drm/i915: Revert i915.semaphore=1 default from 47ae63e0
vga_switcheroo: don't toggle-switch devices
drm/radeon/kms: add some evergreen/ni safe regs
drm/radeon/kms: fix extended lvds info parsing
drm/radeon/kms: fix tiling reg on fusion
|
|
instances"
This reverts commit 26fc8775b51484d8c0a671198639c6d5ae60533e, which has
been reported to cause boot/resume-time crashes for some users:
https://bbs.archlinux.org/viewtopic.php?id=118751.
Signed-off-by: Chris Ball <cjb@laptop.org>
Cc: <stable@kernel.org>
|
|
This patch fixes a bug reported by a customer, who found
that many unreasonable error interrupts reported on all
non-boot CPUs (APs) during the system boot stage.
According to Chapter 10 of Intel Software Developer Manual
Volume 3A, Local APIC may signal an illegal vector error when
an LVT entry is set as an illegal vector value (0~15) under
FIXED delivery mode (bits 8-11 is 0), regardless of whether
the mask bit is set or an interrupt actually happen. These
errors are seen as error interrupts.
The initial value of thermal LVT entries on all APs always reads
0x10000 because APs are woken up by BSP issuing INIT-SIPI-SIPI
sequence to them and LVT registers are reset to 0s except for
the mask bits which are set to 1s when APs receive INIT IPI.
When the BIOS takes over the thermal throttling interrupt,
the LVT thermal deliver mode should be SMI and it is required
from the kernel to keep AP's LVT thermal monitoring register
programmed as such as well.
This issue happens when BIOS does not take over thermal throttling
interrupt, AP's LVT thermal monitor register will be restored to
0x10000 which means vector 0 and fixed deliver mode, so all APs will
signal illegal vector error interrupts.
This patch check if interrupt delivery mode is not fixed mode before
restoring AP's LVT thermal monitor register.
Signed-off-by: Youquan Song <youquan.song@intel.com>
Acked-by: Suresh Siddha <suresh.b.siddha@intel.com>
Acked-by: Yong Wang <yong.y.wang@intel.com>
Cc: hpa@linux.intel.com
Cc: joe@perches.com
Cc: jbaron@redhat.com
Cc: trenn@suse.de
Cc: kent.liu@intel.com
Cc: chaohong.guo@intel.com
Cc: <stable@kernel.org> # As far back as possible
Link: http://lkml.kernel.org/r/1303402963-17738-1-git-send-email-youquan.song@intel.com
Signed-off-by: Ingo Molnar <mingo@elte.hu>
|
|
We need to hold the dev->mode_config.mutex whilst detecting the output
status. But we also need to drop it for the call into
drm_fb_helper_single_fb_probe(), which indirectly acquires the lock when
attaching the fbcon.
Failure to do so exposes a race with normal output probing. Detected by
adding some warnings that the mutex is held to the backend detect routines:
[ 17.772456] WARNING: at drivers/gpu/drm/i915/intel_crt.c:471 intel_crt_detect+0x3e/0x373 [i915]()
[ 17.772458] Hardware name: Latitude E6400
[ 17.772460] Modules linked in: ....
[ 17.772582] Pid: 11, comm: kworker/0:1 Tainted: G W 2.6.38.4-custom.2 #8
[ 17.772584] Call Trace:
[ 17.772591] [<ffffffff81046af5>] ? warn_slowpath_common+0x78/0x8c
[ 17.772603] [<ffffffffa03f3e5c>] ? intel_crt_detect+0x3e/0x373 [i915]
[ 17.772612] [<ffffffffa0355d49>] ? drm_helper_probe_single_connector_modes+0xbf/0x2af [drm_kms_helper]
[ 17.772619] [<ffffffffa03534d5>] ? drm_fb_helper_probe_connector_modes+0x39/0x4d [drm_kms_helper]
[ 17.772625] [<ffffffffa0354760>] ? drm_fb_helper_hotplug_event+0xa5/0xc3 [drm_kms_helper]
[ 17.772633] [<ffffffffa035577f>] ? output_poll_execute+0x146/0x17c [drm_kms_helper]
[ 17.772638] [<ffffffff81193c01>] ? cfq_init_queue+0x247/0x345
[ 17.772644] [<ffffffffa0355639>] ? output_poll_execute+0x0/0x17c [drm_kms_helper]
[ 17.772648] [<ffffffff8105b540>] ? process_one_work+0x193/0x28e
[ 17.772652] [<ffffffff8105c6bc>] ? worker_thread+0xef/0x172
[ 17.772655] [<ffffffff8105c5cd>] ? worker_thread+0x0/0x172
[ 17.772658] [<ffffffff8105c5cd>] ? worker_thread+0x0/0x172
[ 17.772663] [<ffffffff8105f767>] ? kthread+0x7a/0x82
[ 17.772668] [<ffffffff8100a724>] ? kernel_thread_helper+0x4/0x10
[ 17.772671] [<ffffffff8105f6ed>] ? kthread+0x0/0x82
[ 17.772674] [<ffffffff8100a720>] ? kernel_thread_helper+0x0/0x10
Reported-by: Frederik Himpe <fhimpe@telenet.be>
References: https://bugs.freedesktop.org/show_bug.cgi?id=36394
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Signed-off-by: Dave Airlie <airlied@redhat.com>
|
|
My Q67 / i7-2600 box has rev09 Sandy Bridge graphics. It hangs
instantly when GNOME loads and it hangs so hard the reset button
doesn't work. Setting i915.semaphore=0 fixes it.
Semaphores were disabled in a1656b9090f7008d2941c314f5a64724bea2ae37
in 2.6.38 and were re-enabled by
commit 47ae63e0c2e5fdb582d471dc906eb29be94c732f
Merge: c59a333 467cffb
Author: Chris Wilson <chris@chris-wilson.co.uk>
Date: Mon Mar 7 12:32:44 2011 +0000
Merge branch 'drm-intel-fixes' into drm-intel-next
Apply the trivial conflicting regression fixes, but keep GPU semaphores
enabled.
Conflicts:
drivers/gpu/drm/i915/i915_drv.h
drivers/gpu/drm/i915/i915_gem_execbuffer.c
(It's worth noting that the offending change is i915_drv.c,
which is not a conflict.)
Signed-off-by: Andy Lutomirski <luto@mit.edu>
Acked-by: Keith Packard <keithp@keithp.com>
Signed-off-by: Dave Airlie <airlied@redhat.com>
|
|
If the requested device is already active, ignore the request.
This restores the original behaviour of the interface. The change was
probably an unintended side effect of
commit 66b37c6777c4 vga_switcheroo: split switching into two stages
which did not take into account to duplicate the !active check in the split-off
stage2.
Fix this by factoring that check out of stage1 into the debugfs_write routine.
References: https://bugzilla.kernel.org/show_bug.cgi?id=34252
Reported-by: Igor Murzov <e-mail@date.by>
Tested-by: Igor Murzov <e-mail@date.by>
Signed-off-by: Florian Mickler <florian@mickler.org>
Signed-off-by: Dave Airlie <airlied@redhat.com>
|
|
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/acme/linux-2.6 into perf/urgent
|
|
* git://git.kernel.org/pub/scm/linux/kernel/git/mason/btrfs-unstable:
Btrfs: fix FS_IOC_SETFLAGS ioctl
Btrfs: fix FS_IOC_GETFLAGS ioctl
fs: remove FS_COW_FL
Btrfs: fix easily get into ENOSPC in mixed case
Prevent oopsing in posix_acl_valid()
|
|
Without this patch every access to ip_vs in procfs will increase
the netns count i.e. an unbalanced get_net()/put_net().
(ipvsadm commands also use procfs.)
The result is you can't exit a netns if reading ip_vs_* procfs entries.
Signed-off-by: Hans Schillstrom <hans.schillstrom@ericsson.com>
Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org>
|
|
The commit 6b1e960fdbd75dcd9bcc3ba5ff8898ff1ad30b6e
bridge: Reset IPCB when entering IP stack on NF_FORWARD
broke forwarding of IPV6 packets in bridge because it would
call bp_parse_ip_options with an IPV6 packet.
Reported-by: Noah Meyerhans <noahm@debian.org>
Signed-off-by: Stephen Hemminger <shemminger@vyatta.com>
Reviewed-by: Eric Dumazet <eric.dumazet@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org>
|
|
The PERF_EVENT_IOC_SET_OUTPUT ioctl was returning -EINVAL when using
--pid when monitoring multithreaded apps, as we can only share a ring
buffer for events on the same thread if not doing per cpu.
Fix it by using per thread ring buffers.
Tested with:
[root@felicio ~]# tuna -t 26131 -CP | nl
1 thread ctxt_switches
2 pid SCHED_ rtpri affinity voluntary nonvoluntary cmd
3 26131 OTHER 0 0,1 10814276 2397830 chromium-browse
4 642 OTHER 0 0,1 14688 0 chromium-browse
5 26148 OTHER 0 0,1 713602 115479 chromium-browse
6 26149 OTHER 0 0,1 801958 2262 chromium-browse
7 26150 OTHER 0 0,1 1271128 248 chromium-browse
8 26151 OTHER 0 0,1 3 0 chromium-browse
9 27049 OTHER 0 0,1 36796 9 chromium-browse
10 618 OTHER 0 0,1 14711 0 chromium-browse
11 661 OTHER 0 0,1 14593 0 chromium-browse
12 29048 OTHER 0 0,1 28125 0 chromium-browse
13 26143 OTHER 0 0,1 2202789 781 chromium-browse
[root@felicio ~]#
So 11 threads under pid 26131, then:
[root@felicio ~]# perf record -F 50000 --pid 26131
[root@felicio ~]# grep perf_event /proc/`pidof perf`/maps | nl
1 7fa4a2538000-7fa4a25b9000 rwxs 00000000 00:09 4064 anon_inode:[perf_event]
2 7fa4a25b9000-7fa4a263a000 rwxs 00000000 00:09 4064 anon_inode:[perf_event]
3 7fa4a263a000-7fa4a26bb000 rwxs 00000000 00:09 4064 anon_inode:[perf_event]
4 7fa4a26bb000-7fa4a273c000 rwxs 00000000 00:09 4064 anon_inode:[perf_event]
5 7fa4a273c000-7fa4a27bd000 rwxs 00000000 00:09 4064 anon_inode:[perf_event]
6 7fa4a27bd000-7fa4a283e000 rwxs 00000000 00:09 4064 anon_inode:[perf_event]
7 7fa4a283e000-7fa4a28bf000 rwxs 00000000 00:09 4064 anon_inode:[perf_event]
8 7fa4a28bf000-7fa4a2940000 rwxs 00000000 00:09 4064 anon_inode:[perf_event]
9 7fa4a2940000-7fa4a29c1000 rwxs 00000000 00:09 4064 anon_inode:[perf_event]
10 7fa4a29c1000-7fa4a2a42000 rwxs 00000000 00:09 4064 anon_inode:[perf_event]
11 7fa4a2a42000-7fa4a2ac3000 rwxs 00000000 00:09 4064 anon_inode:[perf_event]
[root@felicio ~]#
11 mmaps, one per thread since we didn't specify any CPU list, so we need one
mmap per thread and:
[root@felicio ~]# perf record -F 50000 --pid 26131
^M
^C[ perf record: Woken up 79 times to write data ]
[ perf record: Captured and wrote 20.614 MB perf.data (~900639 samples) ]
[root@felicio ~]# perf report -D | grep PERF_RECORD_SAMPLE | cut -d/ -f2 | cut -d: -f1 | sort -n | uniq -c | sort -nr | nl
1 371310 26131
2 96516 26148
3 95694 26149
4 95203 26150
5 7291 26143
6 87 27049
7 76 661
8 60 29048
9 47 618
10 43 642
[root@felicio ~]#
Ok, one of the threads, 26151 was quiescent, so no samples there, but all the
others are there.
Then, if I specify one CPU:
[root@felicio ~]# perf record -F 50000 --pid 26131 --cpu 1
^C[ perf record: Woken up 1 times to write data ]
[ perf record: Captured and wrote 0.680 MB perf.data (~29730 samples) ]
[root@felicio ~]# perf report -D | grep PERF_RECORD_SAMPLE | cut -d/ -f2 | cut -d: -f1 | sort -n | uniq -c | sort -nr | nl
1 8444 26131
2 2584 26149
3 2518 26148
4 2324 26150
5 123 26143
6 9 661
7 9 29048
[root@felicio ~]#
This machine has two cores, so fewer threads appeared on the radar, and:
[root@felicio ~]# grep perf_event /proc/`pidof perf`/maps | nl
1 7f484b922000-7f484b9a3000 rwxs 00000000 00:09 4064 anon_inode:[perf_event]
[root@felicio ~]#
Just one mmap, as now we can use just one per-cpu buffer instead of the
per-thread needed in the previous case.
For global profiling:
[root@felicio ~]# perf record -F 50000 -a
^C[ perf record: Woken up 26 times to write data ]
[ perf record: Captured and wrote 7.128 MB perf.data (~311412 samples) ]
[root@felicio ~]# grep perf_event /proc/`pidof perf`/maps | nl
1 7fb49b435000-7fb49b4b6000 rwxs 00000000 00:09 4064 anon_inode:[perf_event]
2 7fb49b4b6000-7fb49b537000 rwxs 00000000 00:09 4064 anon_inode:[perf_event]
[root@felicio ~]#
It uses per-cpu buffers.
For just one thread:
[root@felicio ~]# perf record -F 50000 --tid 26148
^C[ perf record: Woken up 2 times to write data ]
[ perf record: Captured and wrote 0.330 MB perf.data (~14426 samples) ]
[root@felicio ~]# perf report -D | grep PERF_RECORD_SAMPLE | cut -d/ -f2 | cut -d: -f1 | sort -n | uniq -c | sort -nr | nl
1 9969 26148
[root@felicio ~]#
[root@felicio ~]# grep perf_event /proc/`pidof perf`/maps | nl
1 7f286a51b000-7f286a59c000 rwxs 00000000 00:09 4064 anon_inode:[perf_event]
[root@felicio ~]#
Tested-by: David Ahern <dsahern@gmail.com>
Tested-by: Lin Ming <ming.m.lin@intel.com>
Cc: Frederic Weisbecker <fweisbec@gmail.com>
Cc: Ingo Molnar <mingo@elte.hu>
Cc: Mike Galbraith <efault@gmx.de>
Cc: Paul Mackerras <paulus@samba.org>
Cc: Peter Zijlstra <peterz@infradead.org>
Cc: Stephane Eranian <eranian@google.com>
Cc: Tom Zanussi <tzanussi@gmail.com>
Link: http://lkml.kernel.org/r/20110426204401.GB1746@ghostprotocols.net
Signed-off-by: Arnaldo Carvalho de Melo <acme@redhat.com>
|
|
The perf_evlist__create_maps was discarding the --cpu parameter when a
--pid or --tid was specified, fix that.
Cc: Frederic Weisbecker <fweisbec@gmail.com>
Cc: Ingo Molnar <mingo@elte.hu>
Cc: Mike Galbraith <efault@gmx.de>
Cc: Paul Mackerras <paulus@samba.org>
Cc: Peter Zijlstra <peterz@infradead.org>
Cc: Stephane Eranian <eranian@google.com>
Cc: Tom Zanussi <tzanussi@gmail.com>
Link: http://lkml.kernel.org/r/20110426204401.GB1746@ghostprotocols.net
Signed-off-by: Arnaldo Carvalho de Melo <acme@redhat.com>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/sage/ceph-client
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/sage/ceph-client:
rbd: fix split bio handling
rbd: fix leak of ops struct
|
|
Steps to reproduce the bug:
- Call FS_IOC_SETLFAGS ioctl with flags=FS_COMPR_FL
- Call FS_IOC_SETFLAGS ioctl with flags=0
- Call FS_IOC_GETFLAGS ioctl, and you'll see FS_COMPR_FL is still set!
Signed-off-by: Li Zefan <lizf@cn.fujitsu.com>
Signed-off-by: Chris Mason <chris.mason@oracle.com>
|
|
As we've added per file compression/cow support.
Signed-off-by: Li Zefan <lizf@cn.fujitsu.com>
Signed-off-by: Chris Mason <chris.mason@oracle.com>
|
|
FS_COW_FL and FS_NOCOW_FL were newly introduced to control per file
COW in btrfs, but FS_NOCOW_FL is sufficient.
The fact is we don't have corresponding BTRFS_INODE_COW flag.
COW is default, and FS_NOCOW_FL can be used to switch off COW for
a single file.
If we mount btrfs with nodatacow, a newly created file will be set with
the FS_NOCOW_FL flag. So to turn on COW for it, we can just clear the
FS_NOCOW_FL flag.
Signed-off-by: Li Zefan <lizf@cn.fujitsu.com>
Signed-off-by: Chris Mason <chris.mason@oracle.com>
|
|
When a btrfs disk is created by mixed data & metadata option, it will have no
pure data or pure metadata space info.
In btrfs's for-linus branch, commit 78b1ea13838039cd88afdd62519b40b344d6c920
(Btrfs: fix OOPS of empty filesystem after balance) initializes space infos at
the very beginning. The problem is this initialization does not take the mixed
case into account, which will cause btrfs will easily get into ENOSPC in mixed
case.
Signed-off-by: Liu Bo <liubo2009@cn.fujitsu.com>
Signed-off-by: Chris Mason <chris.mason@oracle.com>
|
|
If posix_acl_from_xattr() returns an error code, a negative address is
dereferenced causing an oops; fix by checking for error code first.
Signed-off-by: Daniel J Blueman <daniel.blueman@gmail.com>
Reviewed-by: Josef Bacik <josef@redhat.com>
Signed-off-by: Chris Mason <chris.mason@oracle.com>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/jgarzik/libata-dev
* 'upstream-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/jgarzik/libata-dev:
libata: fix oops when LPM is used with PMP
|
|
Shame on me! Commit b1dea800ac39 "tmpfs: fix race between umount and
writepage" fixed the advertized race, but introduced another: as even
its comment makes clear, we cannot safely rely on a peek at list_empty()
while holding no lock - until info->swapped is set, shmem_unuse_inode()
may delete any formerly-swapped inode from the shmem_swaplist, which
in this case would leave a swap area impossible to swapoff.
Although I don't relish taking the mutex every time, I don't care much
for the alternatives either; and at least the peek at list_empty() in
shmem_evict_inode() (a hotter path since most inodes would never have
been swapped) remains safe, because we already truncated the whole file.
Signed-off-by: Hugh Dickins <hughd@google.com>
Cc: stable@kernel.org
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
|
|
ae01b2493c (libata: Implement ATA_FLAG_NO_DIPM and apply it to mcp65)
added ATA_FLAG_NO_DIPM and made ata_eh_set_lpm() check the flag.
However, @ap is NULL if @link points to a PMP link and thus the
unconditional @ap->flags dereference leads to the following oops.
BUG: unable to handle kernel NULL pointer dereference at 0000000000000018
IP: [<ffffffff813f98e1>] ata_eh_recover+0x9a1/0x1510
...
Pid: 295, comm: scsi_eh_4 Tainted: P 2.6.38.5-core2 #1 System76, Inc. Serval Professional/Serval Professional
RIP: 0010:[<ffffffff813f98e1>] [<ffffffff813f98e1>] ata_eh_recover+0x9a1/0x1510
RSP: 0018:ffff880132defbf0 EFLAGS: 00010246
RAX: 0000000000000000 RBX: ffff880132f40000 RCX: 0000000000000000
RDX: ffff88013377c000 RSI: ffff880132f40000 RDI: 0000000000000000
RBP: ffff880132defce0 R08: ffff88013377dc58 R09: ffff880132defd98
R10: 0000000000000000 R11: 00000000ffffffff R12: 0000000000000000
R13: 0000000000000000 R14: ffff88013377c000 R15: 0000000000000000
FS: 0000000000000000(0000) GS:ffff8800bf700000(0000) knlGS:0000000000000000
CS: 0010 DS: 0000 ES: 0000 CR0: 000000008005003b
CR2: 0000000000000018 CR3: 0000000001a03000 CR4: 00000000000406e0
DR0: 0000000000000000 DR1: 0000000000000000 DR2: 0000000000000000
DR3: 0000000000000000 DR6: 00000000ffff0ff0 DR7: 0000000000000400
Process scsi_eh_4 (pid: 295, threadinfo ffff880132dee000, task ffff880133b416c0)
Stack:
0000000000000000 ffff880132defcc0 0000000000000000 ffff880132f42738
ffffffff813ee8f0 ffffffff813eefe0 ffff880132defd98 ffff88013377f190
ffffffffa00b3e30 ffffffff813ef030 0000000032defc60 ffff880100000000
Call Trace:
[<ffffffff81400867>] sata_pmp_error_handler+0x607/0xc30
[<ffffffffa00b273f>] ahci_error_handler+0x1f/0x70 [libahci]
[<ffffffff813faade>] ata_scsi_error+0x5be/0x900
[<ffffffff813cf724>] scsi_error_handler+0x124/0x650
[<ffffffff810834b6>] kthread+0x96/0xa0
[<ffffffff8100cd64>] kernel_thread_helper+0x4/0x10
Code: 8b 95 70 ff ff ff b8 00 00 00 00 48 3b 9a 10 2e 00 00 48 0f 44 c2 48 89 85 70 ff ff ff 48 8b 8d 70 ff ff ff f6 83 69 02 00 00 01 <48> 8b 41 18 0f 85 48 01 00 00 48 85 c9 74 12 48 8b 51 08 48 83
RIP [<ffffffff813f98e1>] ata_eh_recover+0x9a1/0x1510
RSP <ffff880132defbf0>
CR2: 0000000000000018
Fix it by testing @link->ap->flags instead.
stable: ATA_FLAG_NO_DIPM was added during 2.6.39 cycle but was
backported to 2.6.37 and 38. This is a fix for that and thus
also applicable to 2.6.37 and 38.
Signed-off-by: Tejun Heo <tj@kernel.org>
Reported-by: "Nathan A. Mourey II" <nmoureyii@ne.rr.com>
LKML-Reference: <1304555277.2059.2.camel@localhost.localdomain>
Cc: Connor H <cmdkhh@gmail.com>
Cc: stable@kernel.org
Signed-off-by: Jeff Garzik <jgarzik@pobox.com>
|
|
* fbmem:
Further fbcon sanity checking
fbmem: fix remove_conflicting_framebuffers races
|
|
This reverts commit 270dac35c26433d06a89150c51e75ca0181ca7e4.
The commits causes command timeouts on AC plug/unplug. It isn't yet
clear why. As the commit was for a single rather obscure controller,
revert the change for now.
The problem was reported and bisected by Gu Rui in bug#34692.
https://bugzilla.kernel.org/show_bug.cgi?id=34692
Also, reported by Rafael and Michael in the following thread.
http://thread.gmane.org/gmane.linux.kernel/1138771
Signed-off-by: Tejun Heo <tj@kernel.org>
Reported-by: Gu Rui <chaos.proton@gmail.com>
Reported-by: Rafael J. Wysocki <rjw@sisk.pl>
Reported-by: Michael Leun <lkml20100708@newton.leun.net>
Cc: Jian Peng <jipeng2005@gmail.com>
Cc: Jeff Garzik <jgarzik@pobox.com>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
|
|
This moves the
if (num_registered_fb == FB_MAX)
return -ENXIO;
check _AFTER_ the call to do_remove_conflicting_framebuffers() as this
would (now in a safe way) allow a native driver to replace the
conflicting one even if all slots in registered_fb[] are taken.
This also prevents unregistering a framebuffer that is no longer
registered (vga16f will unregister at module unload time even if the
frame buffer had been unregistered earlier due to being found
conflicting).
Signed-off-by: Bruno Prémont <bonbons@linux-vserver.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
|
|
When a register_framebuffer() call results in us removing old
conflicting framebuffers, the new registration_lock doesn't protect that
situation. And we can't just add the same locking to the function,
because these functions call each other: register_framebuffer() calls
remove_conflicting_framebuffers, which in turn calls
unregister_framebuffer for any conflicting entry.
In order to fix it, this just creates wrapper functions around all three
functions and makes the versions that actually do the work be called
"do_xxx()", leaving just the wrapper that gets the lock and calls the
worker function.
So the rule becomes simply that "do_xxxx()" has to be called with the
lock held, and now do_register_framebuffer() can just call
do_remove_conflicting_framebuffers(), and that in turn can call
_do_unregister_framebuffer(), and there is no deadlock, and we can hold
the registration lock over the whole sequence, fixing the races.
It also makes error cases simpler, and fixes one situation where we
would return from unregister_framebuffer() without releasing the lock,
pointed out by Bruno Prémont.
Tested-by: Bruno Prémont <bonbons@linux-vserver.org>
Tested-by: Anca Emanuel <anca.emanuel@gmail.com>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
|
