| Age | Commit message (Collapse) | Author |
|---|
|
The code in 8250.c for detecting ARM/XScale UARTs says:
* Try writing and reading the UART_IER_UUE bit (b6).
* If it works, this is probably one of the Xscale platform's
* internal UARTs.
If the above passes, it then goes on to:
* It's an Xscale.
* We'll leave the UART_IER_UUE bit set to 1 (enabled).
However, the CH352 uses the UART_IER_UUE as the LOWPOWER function,
so it is readable and writable. According to the datasheet:
"LOWPOWER:When the bit is 1, close the internal benchmark
clock of serial port to set into low-power status.
So it essentially gets mis-detected as Xscale, and gets
powered down in the process. The device in question where
this was seen is listed by lspci as:
Serial controller: Device 4348:3253 (rev 10) (prog-if 02 [16550])
Re-using the 353 quirk which just sets flags to fixed and type
to 16550 is suitable for fixing the 352 as well.
Signed-off-by: Wang YanQing <udknight@gmail.com>
Signed-off-by: Paul Gortmaker <paul.gortmaker@windriver.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
Index of atmel_ports[ATMEL_MAX_UART] should be smaller
than ATMEL_MAX_UART.
Signed-off-by: Pawel Wieczorkiewicz <wpawel@gmail.com>
Acked-by: Nicolas Ferre <nicolas.ferre@atmel.com>
Cc: stable <stable@vger.kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
When sending between processes, we always schedule a work item. Our work info
struct has the message embedded in the middle, which means that we end up
overwriting subsequent fields when we copy the (variable-length) message into
it. Move it to the end of the struct.
Acked-by: Dmitry Torokhov <dtor@vmware.com>
Signed-off-by: Andy King <acking@vmware.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/chanwoo/extcon into char-misc-linus
Chanwoo writes:
extcon fixes for 3.9-rc3
This is small fixes against 3.9-rc2.
Fix to max77693 extcon driver:
- Set default value of MUIC register to bring up it.
Fix to max8997 extcon driver:
- Fix null pointer error duing probe when platform data
isn't used.
|
|
This patch (as1663) fixes a regression caused by commit
6e0c3339a6f19d748f16091d0a05adeb1e1f822b (USB: EHCI: unlink one async
QH at a time). In order to avoid keeping multiple QHs in an unusable
intermediate state, that commit changed unlink_empty_async() so that
it unlinks only one empty QH at a time.
However, when the EHCI root hub is suspended, _all_ async QHs need to
be unlinked. ehci_bus_suspend() used to do this by calling
unlink_empty_async(), but now this only unlinks one of the QHs, not
all of them.
The symptom is that when the root hub is resumed, USB communications
don't work for some period of time. This is because ehci-hcd doesn't
realize it needs to restart the async schedule; it assumes that
because some QHs are already on the schedule, the schedule must be
running.
The easiest way to fix the problem is add a new function that unlinks
all the async QHs when the root hub is suspended.
This patch should be applied to all kernels that have the 6e0c3339a6f1
commit.
Signed-off-by: Alan Stern <stern@rowland.harvard.edu>
Reported-and-tested-by: Adrian Bassett <adrian.bassett@hotmail.co.uk>
Cc: stable <stable@vger.kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
Device stucks on filesystem writes, unless following quirk is passed:
echo 04e8:5136:m > /sys/module/usb_storage/parameters/quirks
Add corresponding entry to unusual_devs.h
Signed-off-by: Dmitry Artamonow <mad_soft@inbox.ru>
Cc: stable <stable@vger.kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
xhci has its own interrupt enabling routine, which will try to
use MSI-X/MSI if present. So the usb core shouldn't try to enable
legacy interrupts; on some machines the xhci legacy IRQ setting
is invalid.
v3: Be careful to not break XHCI_BROKEN_MSI workaround (by trenn)
Cc: Bjorn Helgaas <bhelgaas@google.com>
Cc: Oliver Neukum <oneukum@suse.de>
Cc: Thomas Renninger <trenn@suse.de>
Cc: Yinghai Lu <yinghai@kernel.org>
Cc: Frederik Himpe <fhimpe@vub.ac.be>
Cc: David Haerdeman <david@hardeman.nu>
Cc: Alan Stern <stern@rowland.harvard.edu>
Acked-by: Sarah Sharp <sarah.a.sharp@linux.intel.com>
Reviewed-by: Thomas Renninger <trenn@suse.de>
Signed-off-by: Hannes Reinecke <hare@suse.de>
Cc: stable <stable@vger.kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
The vfio drivers call kmalloc or kzalloc, but do not
include <linux/slab.h>, which causes build errors on
ARM.
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Alex Williamson <alex.williamson@redhat.com>
Cc: kvm@vger.kernel.org
|
|
This fixes failure during initialization on Lynx Point LP devices.
ME driver needs to release the device from the reset
only after the FW has completed its flow and indicated
it by delivering an interrupt to the host.
This is the correct behavior for all the ME devices yet the
the previous versions are less susceptive to the implementation
that ignored FW reset completion indication.
We add mei_me_hw_reset_release function which is called
after reset from the interrupt thread or directly
from mei_reset during power down.
Signed-off-by: Tomas Winkler <tomas.winkler@intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
mei_stop calls mei_reset with disabling the interrupts.
It will have the same effect as the open code it replaces in the mei_remove.
The reset sequence on remove is required for the Lynx Point LP devices
to clean the reset state.
mei_stop is called from mei_pci_suspend and mei_remove functions
Signed-off-by: Tomas Winkler <tomas.winkler@intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
Make this depend on CONFIG_PM. This protection is necessary to not
cause any build errors with any combination of PM features especially
when supporting a new SoC where each PM features are being enabled
one-by-one during its depelopment.
Signed-off-by: Hiroshi Doyu <hdoyu@nvidia.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
|
|
clock-event
With recent arm broadcast time clean-up from Mark Rutland, the dummy
broadcast device is always registered with timer subsystem. And since
the rating of the dummy clock event is very high, it may be preferred
over a real clock event.
This is a change in behavior from past and not an intended one. So
reduce the rating of the dummy clock-event so that real clock-event
device is selected when available.
Acked-by: Thomas Gleixner <tglx@linutronix.de>
Acked-by: Mark Rutland <mark.rutland@arm.com>
Signed-off-by: Santosh Shilimkar <santosh.shilimkar@ti.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
|
|
Add support for the AR9462 chip
T: Bus=03 Lev=01 Prnt=01 Port=01 Cnt=01 Dev#= 3 Spd=12 MxCh= 0
D: Ver= 1.10 Cls=e0(wlcon) Sub=01 Prot=01 MxPS=64 #Cfgs= 1
P: Vendor=0cf3 ProdID=0036 Rev= 0.02
C:* #Ifs= 2 Cfg#= 1 Atr=e0 MxPwr=100mA
A: FirstIf#= 0 IfCount= 2 Cls=e0(wlcon) Sub=01 Prot=01
I:* If#= 0 Alt= 0 #EPs= 3 Cls=e0(wlcon) Sub=01 Prot=01 Driver=btusb
E: Ad=81(I) Atr=03(Int.) MxPS= 16 Ivl=1ms
E: Ad=82(I) Atr=02(Bulk) MxPS= 64 Ivl=0ms
E: Ad=02(O) Atr=02(Bulk) MxPS= 64 Ivl=0ms
I:* If#= 1 Alt= 0 #EPs= 2 Cls=e0(wlcon) Sub=01 Prot=01 Driver=btusb
E: Ad=83(I) Atr=01(Isoc) MxPS= 0 Ivl=1ms
E: Ad=03(O) Atr=01(Isoc) MxPS= 0 Ivl=1ms
I: If#= 1 Alt= 1 #EPs= 2 Cls=e0(wlcon) Sub=01 Prot=01 Driver=btusb
E: Ad=83(I) Atr=01(Isoc) MxPS= 9 Ivl=1ms
E: Ad=03(O) Atr=01(Isoc) MxPS= 9 Ivl=1ms
I: If#= 1 Alt= 2 #EPs= 2 Cls=e0(wlcon) Sub=01 Prot=01 Driver=btusb
E: Ad=83(I) Atr=01(Isoc) MxPS= 17 Ivl=1ms
E: Ad=03(O) Atr=01(Isoc) MxPS= 17 Ivl=1ms
I: If#= 1 Alt= 3 #EPs= 2 Cls=e0(wlcon) Sub=01 Prot=01 Driver=btusb
E: Ad=83(I) Atr=01(Isoc) MxPS= 25 Ivl=1ms
E: Ad=03(O) Atr=01(Isoc) MxPS= 25 Ivl=1ms
I: If#= 1 Alt= 4 #EPs= 2 Cls=e0(wlcon) Sub=01 Prot=01 Driver=btusb
E: Ad=83(I) Atr=01(Isoc) MxPS= 33 Ivl=1ms
E: Ad=03(O) Atr=01(Isoc) MxPS= 33 Ivl=1ms
I: If#= 1 Alt= 5 #EPs= 2 Cls=e0(wlcon) Sub=01 Prot=01 Driver=btusb
E: Ad=83(I) Atr=01(Isoc) MxPS= 49 Ivl=1ms
E: Ad=03(O) Atr=01(Isoc) MxPS= 49 Ivl=1ms
Cc: <stable@vger.kernel.org>
Cc: Gustavo Padovan <gustavo.padovan@collabora.co.uk>
Signed-off-by: Ming Lei <ming.lei@canonical.com>
Signed-off-by: Gustavo Padovan <gustavo.padovan@collabora.co.uk>
|
|
This patch fixes a kernel crash when using precise sampling (PEBS)
after a suspend/resume. Turns out the CPU notifier code is not invoked
on CPU0 (BP). Therefore, the DS_AREA (used by PEBS) is not restored properly
by the kernel and keeps it power-on/resume value of 0 causing any PEBS
measurement to crash when running on CPU0.
The workaround is to add a hook in the actual resume code to restore
the DS Area MSR value. It is invoked for all CPUS. So for all but CPU0,
the DS_AREA will be restored twice but this is harmless.
Reported-by: Linus Torvalds <torvalds@linux-foundation.org>
Signed-off-by: Stephane Eranian <eranian@google.com>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
|
|
There is an additional HSW CPU-id, 0x46,
which has C-states exactly like CPU-id 0x45.
Signed-off-by: Len Brown <len.brown@intel.com>
|
|
There is an additional HSW CPU-id, 0x46,
which has C-states exactly like CPU-id 0x45.
Signed-off-by: Len Brown <len.brown@intel.com>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/linville/wireless into for-davem
|
|
git://git.pengutronix.de/git/imx/linux-2.6 into fixes
From Sascha Hauer <s.hauer@pengutronix.de>:
Two small ARM i.MX fixes for v3.9-rc
- Fix i.MX25 DT compilation
- Enable MAX clk on i.MX35
* tag 'arm-imx-fixes-for-3.9-rc' of git://git.pengutronix.de/git/imx/linux-2.6:
ARM: i.MX35: enable MAX clock
ARM: i.MX25: Fix DT compilation
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
|
|
The i.MX35 has two bits per clock gate which are decoded as follows:
0b00 -> clock off
0b01 -> clock is on in run mode, off in wait/doze
0b10 -> clock is on in run/wait mode, off in doze
0b11 -> clock is always on
The reset value for the MAX clock is 0b10.
The MAX clock is needed by the SoC, yet unused in the Kernel, so the
common clock framework will disable it during late init time. It will
only disable clocks though which it detects as being turned on. This
detection is made depending on the lower bit of the gate. If the reset
value has been altered by the bootloader to 0b11 the clock framework
will detect the clock as turned on, yet unused, hence it will turn it
off and the system locks up.
This patch turns the MAX clock on unconditionally making the Kernel
independent of the bootloader.
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
|
|
During the transition to the generic parser, the hook to the codec
specific automute function was forgotten. This resulted in the silent
output on some MacBooks.
Signed-off-by: Takashi Iwai <tiwai@suse.de>
|
|
When neighbour table is full, dst_neigh_lookup/dst_neigh_lookup_skb will return
-ENOBUFS which is absolutely non zero, while all the code in kernel which use
above functions assume failure only on zero return which will cause panic. (for
example: : https://bugzilla.kernel.org/show_bug.cgi?id=54731).
This patch corrects above error with smallest changes to kernel source code and
also correct two return value check missing bugs in drivers/infiniband/hw/cxgb4/cm.c
Tested on my x86_64 SMP machine
Reported-by: Zhouyi Zhou <zhouzhouyi@gmail.com>
Tested-by: Zhouyi Zhou <zhouzhouyi@gmail.com>
Signed-off-by: Zhouyi Zhou <zhouzhouyi@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
The Kconfig file help information incorrectly mentions that the
SMSC LAN75xx config option is for SMSC LAN95xx devices.
Signed-off-by: Robert de Vries <rhdv@xs4all.nl>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/jesse/openvswitch
Jesse Gross says:
====================
A few different bug fixes, including several for issues with userspace
communication that have gone unnoticed up until now. These are intended
for net/3.9.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Commit dc975382d2ef36be7e78fac3717927de1a5abcd8 introduces napi support
but never calls napi_disable. This will generate a kernel oops
(kernel BUG at include/linux/netdevice.h:473!) every time, when
ndo_stop is called followed by ndo_start.
Add the missing napi_diable call.
Signed-off-by: Georg Hofmann <georg@hofmannsweb.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Proviously we would only restart the FEC when PHY link or duplex state
changed. PHY does not always bring down the link for speed changes, in
which case we would not detect any change and keep FEC running.
Switching link speed without restarting the FEC results in the FEC being
stuck in an indefinite state, generating error conditions for every
packet.
Signed-off-by: Lucas Stach <l.stach@pengutronix.de>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
As the translation is stateless, using it in nat table
doesn't work (only initial packet is translated).
filter table OUTPUT works but won't re-route the packet after translation.
Signed-off-by: Florian Westphal <fw@strlen.de>
Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org>
|
|
2^16 = 0xffff, not 0xfffff (note the extra 'f'). Not dangerous since you
adjust it to min_t(data_len, skb->len) just after on.
Reported-by: Eric Dumazet <eric.dumazet@gmail.com>
Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org>
|
|
In (c296bb4 netfilter: nf_conntrack: refactor l4proto support for netns)
the l4proto gre/dccp/udplite/sctp registration happened before the pernet
subsystem, which is wrong.
Register pernet subsystem before register L4proto since after register
L4proto, init_conntrack may try to access the resources which allocated
in register_pernet_subsys.
Reported-by: Alexey Dobriyan <adobriyan@gmail.com>
Cc: Alexey Dobriyan <adobriyan@gmail.com>
Signed-off-by: Gao feng <gaofeng@cn.fujitsu.com>
Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org>
|
|
Scorpion processors have always been v7 CPUs. Fix the Kconfig
text to reflect this.
Reported-by: Stepan Moskovchenko <stepanm@codeaurora.org>
Signed-off-by: Stephen Boyd <sboyd@codeaurora.org>
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
|
|
From Haojian Zhuang <haojian.zhuang@gmail.com>:
* 'armsoc/fix' of git://github.com/hzhuang1/linux:
ARM: mmp: add platform_device head file in gplugd
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
|
|
arch/arm/mach-mmp/gplugd.c: In function ‘gplugd_init’:
arch/arm/mach-mmp/gplugd.c:188:2: error: implicit declaration of
function ‘platform_device_register’
[-Werror=implicit-function-declaration]
cc1: some warnings being treated as errors
make[1]: *** [arch/arm/mach-mmp/gplugd.o] Error 1
make: *** [arch/arm/mach-mmp] Error 2
So append platform_device.h to resolve build issue.
Signed-off-by: Haojian Zhuang <haojian.zhuang@linaro.org>
|
|
"chn" here is a number between 0 and 255, but ->chn_info[] only has
16 elements so there is a potential write beyond the end of the
array.
If the seq_mode isn't SEQ_2 then we let the individual drivers
(either opl3.c or midi_synth.c) handle it. Those functions all
do a bounds check on "chn" so I haven't changed anything here.
The opl3.c driver has up to 18 channels and not 16.
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
|
|
4740f73fe5 "mfd: remove use of __devexit" removed the __devexit annotation
on the twl4030_madc_remove function, but left an __exit_p() present on the
pointer to this function. Using __exit_p was as wrong with the devexit in
place as it is now, but now we get a gcc warning about an unused function.
In order for the twl4030_madc_remove to work correctly in built-in code, we
have to remove the __exit_p.
Cc: Bill Pemberton <wfp5p@virginia.edu>
Cc: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
|
|
spec->dsp_state is initialized to DSP_DOWNLOAD_INIT, no need to reset
and check it in ca0132_download_dsp().
Signed-off-by: Dylan Reid <dgreid@chromium.org>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
|
|
Instead of using the dspload_is_loaded() function, check the dsp_state
that is kept in the spec. The dspload_is_loaded() function returns
true if the DSP transfer was never started. This false-positive leads
to multiple second delays when ca0132_setup_efaults() times out on
each write.
Signed-off-by: Dylan Reid <dgreid@chromium.org>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
|
|
If dspload_image() fails, it was ignored and dspload_wait_loaded() was
still called. dsp_loaded should never be set to true in this case,
skip it. The check in dspload_wait_loaded() return true if the DSP is
loaded or if it never started.
Signed-off-by: Dylan Reid <dgreid@chromium.org>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
|
|
The latency tracers require the buffers to be in overwrite mode,
otherwise they get screwed up. Force the buffers to stay in overwrite
mode when latency tracers are enabled.
Added a flag_changed() method to the tracer structure to allow
the tracers to see what flags are being changed, and also be able
to prevent the change from happing.
Cc: stable@vger.kernel.org
Signed-off-by: Steven Rostedt <rostedt@goodmis.org>
|
|
Changing the overwrite mode for the ring buffer via the trace
option only sets the normal buffer. But the snapshot buffer could
swap with it, and then the snapshot would be in non overwrite mode
and the normal buffer would be in overwrite mode, even though the
option flag states otherwise.
Keep the two buffers overwrite modes in sync.
Cc: stable@vger.kernel.org
Signed-off-by: Steven Rostedt <rostedt@goodmis.org>
|
|
*path is not yet initialized when we check if the widget is connected.
The compiler also warns about this:
sound/soc/soc-dapm.c: In function 'is_connected_output_ep':
sound/soc/soc-dapm.c:824:18: warning: 'path' may be used uninitialized in this function
Signed-off-by: Peter Ujfalusi <peter.ujfalusi@ti.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
|
|
The vm_flags introduced in 6d7825b10dbe ("mm/fremap.c: fix oops on error
path") is supposed to avoid a compiler warning about unitialized
vm_flags without changing the generated code.
However I am concerned that this is going to be very brittle, and fail
with some compiler versions. The failure could be either of:
- compiler could actually load vma->vm_flags before checking for the
!vma condition, thus reintroducing the oops
- compiler could optimize out the !vma check, since the pointer just got
dereferenced shortly before (so the compiler knows it can't be NULL!)
I propose reversing this part of the change and initializing vm_flags to 0
just to avoid the bogus uninitialized use warning.
Signed-off-by: Michel Lespinasse <walken@google.com>
Cc: Tommi Rantala <tt.rantala@gmail.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
|
|
These are part of a longer series that has been submitted some time
ago for the frame buffer tree, but it was never accepted there.
The first two of the five patches are bug fixes, so let's merge
this through arm-soc to get a working 3.9 kernel for at91.
* commit '67cf9c0a':
ARM: at91: fix LCD-wiring mode
atmel_lcdfb: fix 16-bpp modes on older SOCs
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/kgene/linux-samsung into fixes
From Kukjin Kim <kgene.kim@samsung.com>:
* 'v3.9-samsung-fixes-1' of git://git.kernel.org/pub/scm/linux/kernel/git/kgene/linux-samsung:
ARM: EXYNOS: Add dma-cells for generic dma binding support for PL330
ARM: S5PV210: Fix PL330 DMA controller clkdev entries
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
|
|
From Nicolas Ferre <nicolas.ferre@atmel.com>:
Two patches for Device Tree on at91sam9x5/NAND.
Two more for fixing PM suspend/resume IRQ on AIC5 and
GPIO used with pinctrl.
* tag 'at91-fixes' of git://github.com/at91linux/linux-at91:
ARM: at91: fix infinite loop in at91_irq_suspend/resume
ARM: at91: add gpio suspend/resume support when using pinctrl
ARM: at91: dt: at91sam9x5: complete NAND pinctrl
ARM: at91: dt: at91sam9x5: correct NAND pins comments
Includes an update to -rc2
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/paulmck/linux-rcu
Pull fix for hlist_entry_safe() regression from Paul McKenney:
"This contains a single commit that fixes a regression in
hlist_entry_safe(). This macro references its argument twice, which
can cause NULL-pointer errors. This commit applies a gcc statement
expression, creating a temporary variable to avoid the double
reference. This has been posted to LKML at
https://lkml.org/lkml/2013/3/9/75.
Kudos to CAI Qian, whose testing uncovered this, to Eric Dumazet, who
spotted root cause, and to Li Zefan, who tested this commit."
* 'rcu/urgent' of git://git.kernel.org/pub/scm/linux/kernel/git/paulmck/linux-rcu:
list: Fix double fetch of pointer in hlist_entry_safe()
|
|
ARM normally has an accurate clock source, so
we can theoretically use analog joysticks more
accurately and at the same time avoid the
build warning
#warning Precise timer not defined for this architecture.
from the joystick driver.
Now, why anybody would use that driver no ARM I have no
idea, but Ben Dooks enabled it in the s3c2410_defconfig
along with a bunch of other drivers, even though that
platform has neither ISA nor PCI support. It still
seems to be the right thing to fix this quirk.
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Cc: Dmitry Torokhov <dmitry.torokhov@gmail.com>
Cc: Vojtech Pavlik <vojtech@suse.cz>
Cc: Ben Dooks <ben-linux@fluff.org>
|
|
56bc911 "[media] s5p-fimc: Redefine platform data structure for fimc-is"
changed the bus_type member of struct fimc_source_info treewide, but
got one instance wrong in mach-s5pv210, which was evidently not
even build tested.
This adds the missing change to get s5pv210_defconfig to build again.
Applies on the Mauro's media tree.
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Cc: Sylwester Nawrocki <s.nawrocki@samsung.com>
Cc: Kyungmin Park <kyungmin.park@samsung.com>
Cc: Kukjin Kim <kgene.kim@samsung.com>
Cc: Mauro Carvalho Chehab <mchehab@redhat.com>
|
|
Patch 72480014b8 "Fix device clock divisor calculations" was apparently
rebased incorrectly before it got upstream, causing a build error.
Replacing the "prate" pointer with the local parent_rate is most
likely the correct solution.
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Cc: Tony Prisk <linux@prisktech.co.nz>
Cc: Mike Turquette <mturquette@linaro.org>
|
|
The current version of hlist_entry_safe() fetches the pointer twice,
once to test for NULL and the other to compute the offset back to the
enclosing structure. This is OK for normal lock-based use because in
that case, the pointer cannot change. However, when the pointer is
protected by RCU (as in "rcu_dereference(p)"), then the pointer can
change at any time. This use case can result in the following sequence
of events:
1. CPU 0 invokes hlist_entry_safe(), fetches the RCU-protected
pointer as sees that it is non-NULL.
2. CPU 1 invokes hlist_del_rcu(), deleting the entry that CPU 0
just fetched a pointer to. Because this is the last entry
in the list, the pointer fetched by CPU 0 is now NULL.
3. CPU 0 refetches the pointer, obtains NULL, and then gets a
NULL-pointer crash.
This commit therefore applies gcc's "({ })" statement expression to
create a temporary variable so that the specified pointer is fetched
only once, avoiding the above sequence of events. Please note that
it is the caller's responsibility to use rcu_dereference() as needed.
This allows RCU-protected uses to work correctly without imposing
any additional overhead on the non-RCU case.
Many thanks to Eric Dumazet for spotting root cause!
Reported-by: CAI Qian <caiqian@redhat.com>
Reported-by: Eric Dumazet <eric.dumazet@gmail.com>
Signed-off-by: Paul E. McKenney <paulmck@linux.vnet.ibm.com>
Tested-by: Li Zefan <lizefan@huawei.com>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/jack/linux-fs
Pull ext2, ext3, reiserfs, quota fixes from Jan Kara:
"A fix for regression in ext2, and a format string issue in ext3. The
rest isn't too serious."
* 'for_linus' of git://git.kernel.org/pub/scm/linux/kernel/git/jack/linux-fs:
ext2: Fix BUG_ON in evict() on inode deletion
reiserfs: Use kstrdup instead of kmalloc/strcpy
ext3: Fix format string issues
quota: add missing use of dq_data_lock in __dquot_initialize
|
|
Creating snapshot passes extent_root to commit its transaction,
but it can lead to the warning of checking root for quota in
the __btrfs_end_transaction() when someone else is committing
the current transaction. Since we've recorded the needed root
in trans_handle, just use it to get rid of the warning.
Signed-off-by: Liu Bo <bo.li.liu@oracle.com>
Signed-off-by: Chris Mason <chris.mason@fusionio.com>
|
