| Age | Commit message (Collapse) | Author |
|---|
|
IPoIB assumes that high (reserved) octet in the hardware address is 0,
and copies it into the QPN. This violates RFC 4391 (which requires
that the high 8 bits are ignored on receive), and will result in an
invalid QPN being used when interoperating with IPoIB connected mode.
Signed-off-by: Michael S. Tsirkin <mst@mellanox.co.il>
Signed-off-by: Roland Dreier <rolandd@cisco.com>
|
|
master.kernel.org:/pub/scm/linux/kernel/git/roland/infiniband
* 'for-linus' of master.kernel.org:/pub/scm/linux/kernel/git/roland/infiniband:
IB/mad: Fix race between cancel and receive completion
RDMA/amso1100: Fix && typo
RDMA/amso1100: Fix unitialized pseudo_netdev accessed in c2_register_device
IB/ehca: Activate scaling code by default
IB/ehca: Use named constant for max mtu
IB/ehca: Assure 4K alignment for firmware control blocks
|
|
Commit 450efcfd2e1d941e302a8c89322fbfcef237be98 broke Avermedia 777
support.
Added obvious missing "break" statement.
Cc: José Suárez <j.suarez.agapito@gmail.com>
Cc: Michael Krufky <mkrufky@linuxtv.org>
Cc: Mauro Carvalho Chehab <mchehab@infradead.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
|
|
We should only set ->errors to CHECK_CONDITION and so on for requests
that use this field in the SCSI manner.
Signed-off-by: Jens Axboe <jens.axboe@oracle.com>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
|
|
Contrary to what the name misleads you to believe, SG_DXFER_TO_FROM_DEV
is really just a normal read seen from the device side.
This patch fixes http://lkml.org/lkml/2006/10/13/100
Signed-off-by: Jens Axboe <jens.axboe@oracle.com>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
|
|
When ib_cancel_mad() is called, it puts the canceled send on a list
and schedules a "flushed" callback from process context. However,
this leaves a window where a receive completion could be processed
before the send is fully flushed.
This is fine, except that ib_find_send_mad() will find the MAD and
return it to the receive processing, which results in the sender
getting both a successful receive and a "flushed" send completion for
the same request. Understandably, this confuses the sender, which is
expecting only one of these two callbacks, and leads to grief such as
a use-after-free in IPoIB.
Fix this by changing ib_find_send_mad() to return a send struct only
if the status is still successful (and not "flushed"). The search of
the send_list already had this check, so this patch just adds the same
check to the search of the wait_list.
Signed-off-by: Roland Dreier <rolandd@cisco.com>
|
|
Fix the AMSO1100 firmware version computation, which was broken
due to "&&" being used where "&" should have.
Signed-off-by: Jean Delvare <khali@linux-fr.org>
Signed-off-by: Roland Dreier <rolandd@cisco.com>
|
|
Rework some load-time error handling: c2_register_device() leaked when
it failed, and the function that called it didn't check the return code.
Signed-off-by: Tom Tucker <tom@opengridcomputing.com>
Signed-off-by: Roland Dreier <rolandd@cisco.com>
|
|
Change ehca's Kconfig to activates scaling code as default. After
several measurements we saw that this feature prevents dropped packets
(UD) in stress situation. Thus, enabling it helps to improve ehca's
bandwidth through IPoIB.
Signed-off-by: Hoang-Nam Nguyen <hnguyen@de.ibm.com>
Signed-off-by: Roland Dreier <rolandd@cisco.com>
|
|
Define and use a constant EHCA_MAX_MTU instead hardcoded value.
Signed-off-by: Hoang-Nam Nguyen <hnguyen@de.ibm.com>
Signed-off-by: Roland Dreier <rolandd@cisco.com>
|
|
master.kernel.org:/pub/scm/linux/kernel/git/mchehab/v4l-dvb
* 'master' of master.kernel.org:/pub/scm/linux/kernel/git/mchehab/v4l-dvb:
V4L/DVB (4818): Flexcop-usb: fix debug printk
V4L/DVB (4817): Fix uses of "&&" where "&" was intended
V4L/DVB (4816): Change tuner type for Avermedia A16AR
V4L/DVB (4815): Remote support for Avermedia A16AR
V4L/DVB (4814): Remote support for Avermedia 777
V4L/DVB (4804): Fix missing i2c dependency for saa7110
V4L/DVB (4802): Cx88: fix remote control on WinFast 2000XP Expert
V4L/DVB (4795): Tda826x: use correct max frequency
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/paulus/powerpc
* 'merge' of git://git.kernel.org/pub/scm/linux/kernel/git/paulus/powerpc:
[POWERPC] cell: set ARCH_SPARSEMEM_DEFAULT in Kconfig
[POWERPC] Fix cell "new style" mapping and add debug
[POWERPC] pseries: Force 4k update_flash block and list sizes
[POWERPC] CPM_UART: Fix non-console initialisation
[POWERPC] CPM_UART: Fix non-console transmit
[POWERPC] Make sure initrd and dtb sections get into zImage correctly
|
|
* git://oss.sgi.com:8090/xfs/xfs-2.6:
[XFS] Remove KERNEL_VERSION macros from xfs_dmapi.h
[XFS] Prevent a deadlock when xfslogd unpins inodes.
[XFS] Clean up i_flags and i_flags_lock handling.
[XFS] 956664: dm_read_invis() changes i_atime
[XFS] rename uio_read() to xfs_uio_read()
[XFS] Keep lockdep happy.
[XFS] 956618: Linux crashes on boot with XFS-DMAPI filesystem when
|
|
* master.kernel.org:/pub/scm/linux/kernel/git/davem/net-2.6:
[IPVS]: More endianness fixed.
[IPVS]: Compile fix for annotations in userland.
|
|
* master.kernel.org:/pub/scm/linux/kernel/git/sfrench/cifs-2.6:
[CIFS] Fix minor problem with previous patch
[CIFS] Fix mount failure when domain not specified
[CIFS] Explicitly set stat->blksize
[CIFS] NFS stress test generates flood of "close with pending write" messages
|
|
master.kernel.org:/pub/scm/linux/kernel/git/jgarzik/netdev-2.6
* 'upstream-linus' of master.kernel.org:/pub/scm/linux/kernel/git/jgarzik/netdev-2.6:
[PATCH] drivers cris: return on NULL dev_alloc_skb()
[PATCH] com20020 build fix
[PATCH] bonding: lockdep annotation
[PATCH] bcm43xx: Add error checking in bcm43xx_sprom_write()
[PATCH] bcm43xx: Drain TX status before starting IRQs
|
|
This patch (as810c) copies a minimum of 36 bytes of INQUIRY data, even if
the device claims that not all of them are valid. Often badly behaved
devices put plausible data in the Vendor, Product, and Revision strings but
set the Additional Length byte to a small value. Using potentially valid
data is certainly better than allocating a short buffer and then reading
beyond the end of it, which is what we do now.
Signed-off-by: Alan Stern <stern@rowland.harvard.edu>
Cc: James Bottomley <James.Bottomley@steeleye.com>
Cc: Greg KH <greg@kroah.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
|
|
While testing kernel on machine with "irqpoll" option I've caught such a
lockup:
__do_IRQ()
spin_lock(&desc->lock);
desc->chip->ack(); /* IRQ is ACKed */
note_interrupt()
misrouted_irq()
handle_IRQ_event()
if (...)
local_irq_enable_in_hardirq();
/* interrupts are enabled from now */
...
__do_IRQ() /* same IRQ we've started from */
spin_lock(&desc->lock); /* LOCKUP */
Looking at misrouted_irq() code I've found that a potential deadlock like
this can also take place:
1CPU:
__do_IRQ()
spin_lock(&desc->lock); /* irq = A */
misrouted_irq()
for (i = 1; i < NR_IRQS; i++) {
spin_lock(&desc->lock); /* irq = B */
if (desc->status & IRQ_INPROGRESS) {
2CPU:
__do_IRQ()
spin_lock(&desc->lock); /* irq = B */
misrouted_irq()
for (i = 1; i < NR_IRQS; i++) {
spin_lock(&desc->lock); /* irq = A */
if (desc->status & IRQ_INPROGRESS) {
As the second lock on both CPUs is taken before checking that this irq is
being handled in another processor this may cause a deadlock. This issue
is only theoretical.
I propose the attached patch to fix booth problems: when trying to handle
misrouted IRQ active desc->lock may be unlocked.
Acked-by: Ingo Molnar <mingo@redhat.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
|
|
On running the Stress Test on machine for more than 72 hours following
error message was observed.
0:mon> e
cpu 0x0: Vector: 300 (Data Access) at [c00000007ce2f7f0]
pc: c000000000060d90: .dup_fd+0x240/0x39c
lr: c000000000060d6c: .dup_fd+0x21c/0x39c
sp: c00000007ce2fa70
msr: 800000000000b032
dar: ffffffff00000028
dsisr: 40000000
current = 0xc000000074950980
paca = 0xc000000000454500
pid = 27330, comm = bash
0:mon> t
[c00000007ce2fa70] c000000000060d28 .dup_fd+0x1d8/0x39c (unreliable)
[c00000007ce2fb30] c000000000060f48 .copy_files+0x5c/0x88
[c00000007ce2fbd0] c000000000061f5c .copy_process+0x574/0x1520
[c00000007ce2fcd0] c000000000062f88 .do_fork+0x80/0x1c4
[c00000007ce2fdc0] c000000000011790 .sys_clone+0x5c/0x74
[c00000007ce2fe30] c000000000008950 .ppc_clone+0x8/0xc
The problem is because of race window. When if(expand) block is executed in
dup_fd unlocking of oldf->file_lock give a window for fdtable in oldf to be
modified. So actual open_files in oldf may not match with open_files
variable.
Cc: Vadim Lobanov <vlobanov@speakeasy.net>
Cc: <stable@kernel.org>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
|
|
Prevent git from reporting this useless status:
On branch refs/heads/master
Untracked files:
(use "git add" to add to commit)
TAGS
scripts/kconfig/lkc_defs.h
scripts/kconfig/qconf.moc
nothing to commit
Signed-off-by: Franck Bui-Huu <fbuihuu@gmail.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
|
|
If you call set_personality() with an expression such as:
set_personality(foo ? PERS_FOO1 : PERS_FOO2);
then this evaluates to:
((current->personality == foo ? PERS_FOO1 : PERS_FOO2) ? ...
which is obviously not the intended result. Add the missing parents
to ensure this gets evaluated as expected:
((current->personality == (foo ? PERS_FOO1 : PERS_FOO2)) ? ...
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
|
|
The following patch resolves the divide by zero error I encountered on my
system:
http://marc.10east.com/?l=linux-fbdev-devel&m=116058257024413&w=2
I accomplished this by merging what I thought was appropriate from:
http://webcvs.freedesktop.org/xorg/driver/xf86-video-nv/src/
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
|
|
Fix improper use of "&&" when "&" was intended.
Signed-off-by: Jean Delvare <khali@linux-fr.org>
Signed-off-by: Corey Minyard <minyard@acm.org>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
|
|
Fix MSPEC driver to build for non SN2 enabled configs as the driver should
work in cached and uncached modes (no fetchop) on these systems. In
addition make MSPEC select IA64_UNCACHED_ALLOCATOR, which is required for
it and move it to arch/ia64/Kconfig to avoid warnings on non ia64
architectures running allmodconfig. Once the Kconfig code is fixed, we can
move it back.
Signed-off-by: Jes Sorensen <jes@sgi.com>
Cc: Fernando Luis Vzquez Cao <fernando@oss.ntt.co.jp>
Cc: "Luck, Tony" <tony.luck@intel.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
|
|
The PCI sysfs attributes are created after the initial PCI bus scan. With
the addition of more return value checking and assertions in the device and
sysfs layers we now can get dumps like this on sparc64:
[ 20.135032] Call Trace:
[ 20.135042] [0000000000537f88] pci_remove_bus_device+0x30/0xc0
[ 20.135076] [000000000078f890] pci_fill_in_pbm_cookies+0x98/0x440
[ 20.135109] [000000000042e828] sabre_scan_bus+0x230/0x400
[ 20.135139] [000000000078c710] pcibios_init+0x58/0xa0
[ 20.135159] [0000000000416f14] init+0x9c/0x2e0
[ 20.135190] [0000000000417a50] kernel_thread+0x38/0x60
[ 20.135211] [0000000000417170] rest_init+0x18/0x40
[ 20.135514] PCI0(PBMB): Bus running at 33MHz
It's triggering because removal of the "config" PCI sysfs file for the
device fails.
On sparc64, after probing the device, we'll delete the PCI device via
pci_remove_bus_device() if we cannot find the firmware device tree node
corresponding to it.
This is fine, but at this point the sysfs files for the PCI device won't be
setup yet.
So we should not try to do anything in pci_remove_sysfs_dev_files() if
pci_sysfs_init() has not run yet.
Signed-off-by: David S. Miller <davem@davemloft.net>
Acked-by: Greg Kroah-Hartman <gregkh@suse.de>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
|
|
- reorder 'struct vm_struct' to speedup lookups on CPUS with small cache
lines. The fields 'next,addr,size' should be now in the same cache line,
to speedup lookups.
- One minor cleanup in __get_vm_area_node()
- Bugfixes in vmalloc_user() and vmalloc_32_user() NULL returns from
__vmalloc() and __find_vm_area() were not tested.
[akpm@osdl.org: remove redundant BUG_ONs]
Signed-off-by: Eric Dumazet <dada1@cosmosbay.com>
Cc: Nick Piggin <nickpiggin@yahoo.com.au>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
|
|
.. fix debug printk. Why, oh why, one would want to do
(u16 & 0xff) << 8
and print it with %02x format?
Acked-by: Patrick Boettcher <pb@linuxtv.org>
Signed-off-by: Alexey Dobriyan <adobriyan@gmail.com>
Signed-off-by: Michael Krufky <mkrufky@linuxtv.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
|
|
Fix uses of "&&" where "&" was intended in bttv-cards.c and tveeprom.c
Signed-off-by: Jean Delvare <khali@linux-fr.org>
Signed-off-by: Michael Krufky <mkrufky@linuxtv.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
|
|
This changes it from TDA8290 which is allegedly very unlikely to TD1316 which
is allegedly very likely. I didn't get it to work with either, but expected
that this got applied when Mauro sent it to me, so here it goes again; feel
free to drop it to the floor. :-)
Signed-off-by: Petr Baudis <pasky@ucw.cz>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
|
|
The remote as well as the GPIO interface is the same as what comes with 777.
For an example of mplayer lirc configuration, see
http://pasky.or.cz/~pasky/dev/v4l/lircrc
Signed-off-by: Petr Baudis <pasky@ucw.cz>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
|
|
I didn't test it personally since I don't have this card, but A16AR uses the
same interface and that one certainly does work perfectly (see the next patch).
This patch was originally sent in
http://marc.theaimsgroup.com/?l=linux-video&m=114743413825375&w=2
https://www.redhat.com/mailman/private/video4linux-list/2006-May/msg00103.html
but never got applied. This version has some trivial modifications and drops
the weird gpio hack (it's not clear what practical purpose does it serve).
Signed-off-by: Jose Alberto Reguero <jareguero@telefonica.net>
Signed-off-by: Petr Baudis <pasky@ucw.cz>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
|
|
drivers/media/video/saa7110.c:112: undefined reference to `i2c_master_send'
drivers/built-in.o: In function `saa7110_read':
drivers/media/video/saa7110.c:130: undefined reference to `i2c_smbus_read_byte'
drivers/media/video/saa7110.c:130: undefined reference to `i2c_smbus_read_byte'
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
|
|
fix remote control on WinFast 2000XP Expert by setting timing back to 1 ms,
like it was in the original patch by Robert Reid.
Signed-off-by: Hermann Pitton <hermann-pitton@arcor.de>
Signed-off-by: Michael Krufky <mkrufky@linuxtv.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
|
|
sparse "defined twice" warning
Signed-off-by: Alexey Dobriyan <adobriyan@gmail.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Michael Krufky <mkrufky@linuxtv.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
|
|
SGI-PV: 957005
SGI-Modid: xfs-linux-melb:xfs-kern:27398a
Signed-off-by: David Chinner <dgc@sgi.com>
Signed-off-by: Michal Piotrowski <michal.k.k.piotrowski@gmail.com>
Signed-off-by: Tim Shimmin <tes@sgi.com>
|
|
The previous fixes for the use after free in xfs_iunpin left a nasty log
deadlock when xfslogd unpinned the inode and dropped the last reference to
the inode. the ->clear_inode() method can issue transactions, and if the
log was full, the transaction could push on the log and get stuck trying
to push the inode it was currently unpinning.
To fix this, we provide xfs_iunpin a guarantee that it will always have a
valid xfs_inode <-> linux inode link or a particular flag will be set on
the inode. We then use log forces during lookup to ensure transactions are
completed before we recycle the inode. This ensures that xfs_iunpin will
never use the linux inode after it is being freed, and any lookup on an
inode on the reclaim list will wait until it is safe to attach a new linux
inode to the xfs inode.
SGI-PV: 956832
SGI-Modid: xfs-linux-melb:xfs-kern:27359a
Signed-off-by: David Chinner <dgc@sgi.com>
Signed-off-by: Shailendra Tripathi <stripathi@agami.com>
Signed-off-by: Takenori Nagano <t-nagano@ah.jp.nec.com>
Signed-off-by: Tim Shimmin <tes@sgi.com>
|
|
SGI-PV: 956832
SGI-Modid: xfs-linux-melb:xfs-kern:27358a
Signed-off-by: David Chinner <dgc@sgi.com>
Signed-off-by: Nathan Scott <nscott@aconex.com>
Signed-off-by: Tim Shimmin <tes@sgi.com>
|
|
SGI-PV: 956664
SGI-Modid: xfs-linux-melb:xfs-kern:27315a
Signed-off-by: Vlad Apostolov <vapo@sgi.com>
Signed-off-by: Sam Vaughan <sjv@sgi.com>
Signed-off-by: Tim Shimmin <tes@sgi.com>
|
|
SGI-PV: 957004
SGI-Modid: xfs-linux-melb:xfs-kern:27231a
Signed-off-by: Vlad Apostolov <vapo@sgi.com>
Signed-off-by: Tim Shimmin <tes@sgi.com>
|
|
SGI-PV: 956964
SGI-Modid: xfs-linux-melb:xfs-kern:27200a
Signed-off-by: Tim Shimmin <tes@sgi.com>
Signed-off-by: David Chinner <dgc@sgi.com>
Signed-off-by: Eric Sandeen <sandeen@sandeen.net>
|
|
CONFIG_XFS_TRACE is on
SGI-PV: 956618
SGI-Modid: xfs-linux-melb:xfs-kern:27196a
Signed-off-by: Vlad Apostolov <vapo@sgi.com>
Signed-off-by: Tim Shimmin <tes@sgi.com>
|
|
- make sure port in FTP data is in network order (in fact it was looking
buggy for big endian boxes before Viro's changes)
- htonl -> htons for port
Signed-off-by: Julian Anastasov <ja@ssi.bg>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/linville/wireless-2.6 into upstream-fixes
|
|
If the next descriptor array entry cannot be allocated by dev_alloc_skb(),
return immediately so it is not dereferenced later. We cannot register the
device with a partial descriptor list.
Cc: Mikael Starvik <starvik@axis.com>
Signed-off-by: David Rientjes <rientjes@cs.washington.edu>
Cc: Jeff Garzik <jeff@garzik.org>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
|
|
com20020.c needs to export functions if either of the ISA or PCI modules
are built as loadable modules. Or they could always be exported.
WARNING: "com20020_found" [drivers/net/arcnet/com20020-pci.ko] undefined!
WARNING: "com20020_check" [drivers/net/arcnet/com20020-pci.ko] undefined!
Signed-off-by: Randy Dunlap <randy.dunlap@oracle.com>
Cc: Toralf Forster <toralf.foerster@gmx.de>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
|
|
=============================================
[ INFO: possible recursive locking detected ]
2.6.17-1.2600.fc6 #1
Signed-off-by: Jeff Garzik <jeff@garzik.org>
|
|
The current cell processor support needs sparsemem, so set it as
the default memory model.
Signed-off-by: Geoff Levand <geoffrey.levand@am.sony.com>
Acked-by: Arnd Bergmann <arnd.bergmann@de.ibm.com>
Signed-off-by: Paul Mackerras <paulus@samba.org>
|
|
This fixes a typo in the "new style" code for mapping SPE resources,
which causes it to try to map the same resource 4 times.
It also adds some pr_debug's that are useful to track down issues with
the firmware when bringinh up new machines.
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Signed-off-by: Paul Mackerras <paulus@samba.org>
|
|
The enablement of 64k pages on pseries platforms exposed a bug in
the RTAS mechanism for updating firmware. RTAS assumes 4k for flash
block and list sizes, and use of any other sizes results in a failure,
even though PAPR does not specify any such requirement.
This patch changes the rtas_flash module to force the use of 4k memory
block and list sizes when preparing and sending a firmware image to
RTAS. The rtas_flash function now uses a slab cache of 4k blocks with
4k alignment, rather than get_zeroed_page(), to allocate the memory for
the flash blocks and lists. The 4k alignment requirement is specified
in PAPR.
Signed-off-by: John Rose <johnrose@austin.ibm.com>
Signed-off-by: Paul Mackerras <paulus@samba.org>
|
|
The cpm_uart driver is initialised incorrectly, if there is a frame buffer
console, and CONFIG_SERIAL_CPM_CONSOLE is defined. The driver fails to
call cpm_uart_init_portdesc() and set_lineif() in this case.
Signed-off-by: Kalle Pokki <kalle.pokki@iki.fi>
Signed-off-by: Vitaly Bordug <vbordug@ru.mvista.com>
Signed-off-by: Paul Mackerras <paulus@samba.org>
|
