| Age | Commit message (Collapse) | Author |
|---|
|
da9052_regulator_info and da9053_regulator_info are not used outside
this driver so no need to make the symbol global.
Signed-off-by: Axel Lin <axel.lin@gmail.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
|
|
for da9052-regulator
Reported-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Signed-off-by: David Dajun Chen <dchen@diasemi.com>
Signed-off-by: Ashish Jangam <ashish.jangam@kpitcummins.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
|
|
Reported-by: Stephen Rothwell <sfr@canb.auug.org.au>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
|
|
The Dialog PMIC has below featured regulators:-
DA9052-BC - 4 DVS Buck converters 0.5V - 3.6V upto 1Amp.
DA9053-AA/BX - 4 DVS Buck converters 0.5V - 2.5V upto 3Amp.
DA9052/53 - 10 Programmable LDO's High PSSR, 1% accuracy.
This patch support all the DA9052 and Da9053 regulators. The output voltages are
fully programmable via I2C or SPI interface. The platform data with regulation
constraints is passed down from the board to the regulator.
Signed-off-by: David Dajun Chen <dchen@diasemi.com>
Signed-off-by: Ashish Jangam <ashish.jangam@kpitcummins.com>
Tested-by: Ying-Chun Liu (PaulLiu) <paul.liu@linaro.org>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/broonie/regulator into regulator-next
|
|
It's not always true that the device_node of regulator can be found
at dev->of_node at the time when of_get_regulator_init_data() is being
called, because in some cases the regulator nodes in device tree do
not have 'struct device' behind them until regulator_dev gets created
for it by core function regulator_register().
The patch adds device_node as a new parameter to
of_get_regulator_init_data(), so that caller can pass in the node of
regulator directly.
Signed-off-by: Shawn Guo <shawn.guo@linaro.org>
Cc: Mark Brown <broonie@opensource.wolfsonmicro.com>
Cc: Liam Girdwood <lrg@ti.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
|
|
Otherwise there is no way in the bindings to configure a fixed voltage
via software. It seems reasonable to assume that if the binding explicitly
specifies a voltage we want to actually use that voltage.
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
|
|
The commit 2c043bcbf287 ("regulator: pass additional of_node to
regulator_register()") added an additional parameter to the
regulator_register() API.
Update the Documentation accordingly to reflect the change
in the function signature.
Reported-by: Thomas Abraham <thomas.abraham@linaro.org>
Signed-off-by: Rajendra Nayak <rnayak@ti.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
|
|
This allows read-only access to the device configuration which may be
useful for diagnostics.
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Acked-by: Liam Girdwood <lrg@ti.com>
|
|
'regulator/for-linus' into regulator-next
|
|
Device tree compiler does not recognize '-' in label name. Instead,
'_' works fine.
Signed-off-by: Shawn Guo <shawn.guo@linaro.org>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
|
|
SMPS regulator voltage control differs from the one of the LDO ones.
Current TWL code was using LDO regulator ops for controlling the SMPS
regulators, which fails. This was fixed fixed by adding separate
regulator type which uses correct logic and calculations for the
voltage levels.
Signed-off-by: Tero Kristo <t-kristo@ti.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Cc: stable@kernel.org
|
|
|
|
This is caused by dereferencing 'rdev' after device_unregister() in
the regulator_unregister() function. 'rdev' is freed by
device_unregister(), so it must not be dereferenced after this call.
[Edited commit message for legibility -- broonie]
Signed-off-by: Lothar Waßmann <LW@KARO-electronics.de>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
|
|
|
|
module_platform_driver()
This patch converts virtual and userspace regulator consumer drivers to use the
module_platform_driver() macro which makes the code smaller and a bit simpler.
Signed-off-by: Axel Lin <axel.lin@gmail.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
|
|
The implementation in aat2870_update() already did the bitwise and operation
against mask parameter.
Signed-off-by: Axel Lin <axel.lin@gmail.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
|
|
aat2870_get_regulator
In current implementation, the pointer ri is not NULL if no id is matched.
Fix it by checking i == ARRAY_SIZE(aat2870_regulators) if no id is matched.
Signed-off-by: Axel Lin <axel.lin@gmail.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Cc: stable@kernel.org
|
|
|
|
of_get_fixed_voltage_config() may return NULL, return -ENOMEM in this case
so we don't dereference NULL pointer.
Signed-off-by: Axel Lin <axel.lin@gmail.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
|
|
|
|
It is not used outside this driver so no need to make the symbol global.
Signed-off-by: Axel Lin <axel.lin@gmail.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
|
|
of_get_regulator_init_data() may return NULL, thus
check the return value to avoid NULL pointer dereference.
Signed-off-by: Axel Lin <axel.lin@gmail.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
|
|
of_get_regulator_init_data is called in drivers/regulator/fixed.c
which could be a module.
Export of_get_regulator_init_data to fix below build error:
ERROR: "of_get_regulator_init_data" [drivers/regulator/fixed.ko] undefined!
make[1]: *** [__modpost] Error 1
make: *** [modules] Error 2
Reported-by: Randy Dunlap <rdunlap@xenotime.net>
Signed-off-by: Axel Lin <axel.lin@gmail.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
|
|
|
|
The commit 2c043bcbf287 ("regulator: pass additional of_node to
regulator_register()") caused a compile break because it missed
updating the regulator_register() call in gpio-regulator.c with
the additional parameter (NULL).
The compile break as reported by Stephen Rothwell with the
x86_64 allmodconfig looked like this
drivers/regulator/gpio-regulator.c: In function 'gpio_regulator_probe':
drivers/regulator/gpio-regulator.c:287:8: error: too few arguments to function 'regulator_register'
include/linux/regulator/driver.h:215:23: note: declared here
Reported-by: Stephen Rothwell <sfr@canb.auug.org.au>
Signed-off-by: Rajendra Nayak <rnayak@ti.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
|
|
|
|
* git://github.com/rustyrussell/linux:
virtio-pci: make reset operation safer
virtio-mmio: Correct the name of the guest features selector
virtio: add HAS_IOMEM dependency to MMIO platform bus driver
|
|
virtio pci device reset actually just does an I/O
write, which in PCI is really posted, that is it
can complete on CPU before the device has received it.
Further, interrupts might have been pending on
another CPU, so device callback might get invoked after reset.
This conflicts with how drivers use reset, which is typically:
reset
unregister
a callback running after reset completed can race with
unregister, potentially leading to use after free bugs.
Fix by flushing out the write, and flushing pending interrupts.
This assumes that device is never reset from
its vq/config callbacks, or in parallel with being
added/removed, document this assumption.
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: Rusty Russell <rusty@rustcorp.com.au>
|
|
Guest features selector spelling mistake.
Cc: Pawel Moll <pawel.moll@arm.com>
Cc: Rusty Russell <rusty@rustcorp.com.au>
Cc: virtualization@lists.linux-foundation.org
Signed-off-by: Sasha Levin <levinsasha928@gmail.com>
Signed-off-by: Rusty Russell <rusty@rustcorp.com.au>
|
|
Fix this compile error on s390:
CC [M] drivers/virtio/virtio_mmio.o
drivers/virtio/virtio_mmio.c: In function 'vm_get_features':
drivers/virtio/virtio_mmio.c:107:2: error: implicit declaration of function 'writel'
Cc: Christian Borntraeger <borntraeger@de.ibm.com>
Signed-off-by: Heiko Carstens <heiko.carstens@de.ibm.com>
Acked-by: Pawel Moll <pawel.moll@arm.com>
Signed-off-by: Rusty Russell <rusty@rustcorp.com.au>
|
|
* 'upstream-linus' of git://github.com/jgarzik/libata-dev:
libata: fix build without BMDMA
[libata] ahci_platform: fix DT probing
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/jbarnes/pci
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/jbarnes/pci:
PCI hotplug: shpchp: don't blindly claim non-AMD 0x7450 device IDs
PCI: pciehp: wait 100 ms after Link Training check
PCI: pciehp: wait 1000 ms before Link Training check
PCI: pciehp: Retrieve link speed after link is trained
PCI: Let PCI_PRI depend on PCI
PCI: Fix compile errors with PCI_ATS and !PCI_IOV
PCI / ACPI: Make acpiphp ignore root bridges using PCIe native hotplug
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/tyhicks/ecryptfs
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tyhicks/ecryptfs:
eCryptfs: Extend array bounds for all filename chars
eCryptfs: Flush file in vma close
eCryptfs: Prevent file create race condition
|
|
From mhalcrow's original commit message:
Characters with ASCII values greater than the size of
filename_rev_map[] are valid filename characters.
ecryptfs_decode_from_filename() will access kernel memory beyond
that array, and ecryptfs_parse_tag_70_packet() will then decrypt
those characters. The attacker, using the FNEK of the crafted file,
can then re-encrypt the characters to reveal the kernel memory past
the end of the filename_rev_map[] array. I expect low security
impact since this array is statically allocated in the text area,
and the amount of memory past the array that is accessible is
limited by the largest possible ASCII filename character.
This patch solves the issue reported by mhalcrow but with an
implementation suggested by Linus to simply extend the length of
filename_rev_map[] to 256. Characters greater than 0x7A are mapped to
0x00, which is how invalid characters less than 0x7A were previously
being handled.
Signed-off-by: Tyler Hicks <tyhicks@canonical.com>
Reported-by: Michael Halcrow <mhalcrow@google.com>
Cc: stable@kernel.org
|
|
Dirty pages weren't being written back when an mmap'ed eCryptfs file was
closed before the mapping was unmapped. Since f_ops->flush() is not
called by the munmap() path, the lower file was simply being released.
This patch flushes the eCryptfs file in the vm_ops->close() path.
https://launchpad.net/bugs/870326
Signed-off-by: Tyler Hicks <tyhicks@canonical.com>
Cc: stable@kernel.org [2.6.39+]
|
|
The file creation path prematurely called d_instantiate() and
unlock_new_inode() before the eCryptfs inode info was fully
allocated and initialized and before the eCryptfs metadata was written
to the lower file.
This could result in race conditions in subsequent file and inode
operations leading to unexpected error conditions or a null pointer
dereference while attempting to use the unallocated memory.
https://launchpad.net/bugs/813146
Signed-off-by: Tyler Hicks <tyhicks@canonical.com>
Cc: stable@kernel.org
|
|
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/broonie/regulator into regulator-next
|
|
Device nodes in DT can associate themselves with one or more
regulators/supply by providing a list of phandles (to regulator nodes)
and corresponding supply names.
For Example:
devicenode: node@0x0 {
...
...
vmmc-supply = <®ulator1>;
vpll-supply = <®ulator2>;
};
The driver would then do a regulator_get(dev, "vmmc"); to get
regulator1 and do a regulator_get(dev, "vpll"); to get
regulator2.
of_get_regulator() extracts the regulator node for a given
device, based on the supply name.
Use it to look up the regulator for a given consumer from device tree, during
a regulator_get(). If not found fallback and lookup through
the regulator_map_list instead.
Also, since the regulator dt nodes can use the same binding to
associate with a parent regulator/supply, allow the drivers to
specify a supply_name, which can then be used to lookup dt
to find the parent phandle.
Signed-off-by: Rajendra Nayak <rnayak@ti.com>
Acked-by: Grant Likely <grant.likely@secretlab.ca>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
|
|
With device tree support for regulators, its needed that the
regulator_dev->dev device has the right of_node attached.
To be able to do this add an additional parameter to the
regulator_register() api, wherein the dt-adapted driver can
then pass this additional info onto the regulator core.
Signed-off-by: Rajendra Nayak <rnayak@ti.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
|
|
The fixed regulator driver uses of_get_fixed_voltage_config()
to extract fixed_voltage_config structure contents from device tree.
Also add documenation for additional bindings for fixed
regulators that can be passed through dt.
Signed-off-by: Rajendra Nayak <rnayak@ti.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
|
|
The helper routine is meant to be used by the regulator drivers
to extract the regulator_init_data structure from the data
that is passed from device tree.
'consumer_supplies' which is part of regulator_init_data is not extracted
as the regulator consumer mappings are passed through DT differently,
implemented in subsequent patches.
Similarly the regulator<-->parent/supply mapping is handled in
subsequent patches.
Also add documentation for regulator bindings to be used to pass
regulator_init_data struct information from device tree.
Some of the regulator properties which are linux and board specific,
are left out since its not clear if they can
be in someway embedded into the kernel or passed in from DT.
They will be revisited later.
Signed-off-by: Rajendra Nayak <rnayak@ti.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/rostedt/linux-ktest
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/rostedt/linux-ktest:
ktest: Check parent options for iterated tests
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/jdelvare/staging
* 'i2c-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/jdelvare/staging:
i2c: Make i2cdev_notifier_call static
i2c: Delete ANY_I2C_BUS
i2c: Fix device name for 10-bit slave address
i2c-algo-bit: Generate correct i2c address sequence for 10-bit target
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/broonie/regulator
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/broonie/regulator:
regulator: TPS65910: Fix VDD1/2 voltage selector count
|
|
* 'drm-fixes' of git://people.freedesktop.org/~airlied/linux: (31 commits)
drm: integer overflow in drm_mode_dirtyfb_ioctl()
drivers/gpu/vga/vgaarb.c: add missing kfree
drm/radeon/kms/atom: unify i2c gpio table handling
drm/radeon/kms: fix up gpio i2c mask bits for r4xx for real
ttm: Don't return the bo reserved on error path
drm/radeon/kms: add a CS ioctl flag not to rewrite tiling flags in the CS
drm/i915: Fix inconsistent backlight level during disabled
drm, i915: Fix memory leak in i915_gem_busy_ioctl().
drm/i915: Use DPCD value for max DP lanes.
drm/i915: Initiate DP link training only on the lanes we'll be using
drm/i915: Remove trailing white space
drm/i915: Try harder during dp pattern 1 link training
drm/i915: Make DP prepare/commit consistent with DP dpms
drm/i915: Let panel power sequencing hardware do its job
drm/i915: Treat PCH eDP like DP in most places
drm/i915: Remove link_status field from intel_dp structure
drm/i915: Move common PCH_PP_CONTROL setup to ironlake_get_pp_control
drm/i915: Module parameters using '-1' as default must be signed type
drm/i915: Turn on another required clock gating bit on gen6.
drm/i915: Turn on a required 3D clock gating bit on Sandybridge.
...
|
|
Count of selector voltage is required for regulator_set_voltage
to work via set_voltage_sel. VDD1/2 currently have it as zero,
so regulator_set_voltage won't work for VDD1/2.
Update count (n_voltages) for VDD1/2.
Output Voltage = (step value * 12.5 mV + 562.5 mV) * gain
With above expr, number of voltages that can be selected is
step value count * gain count
constant for gain count will be called VDD1_2_NUM_VOLT_COARSE
existing constant for step value count is VDD1_2_NUM_VOLTS,
use VDD1_2_NUM_VOLT_FINE instead to make clear that step value
is not the only component in deciding selectable voltage count
Signed-off-by: Afzal Mohammed <afzal@ti.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
|
|
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
|
|
If we don't know what voltage the regulator is set to return an error
rather than reporting zero volts.
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
|
