| Age | Commit message (Collapse) | Author |
|---|
|
Add ML7213 device information.
ML7213 is companion chip of Intel Atom E6xx series for IVI(In-Vehicle Infotainment).
ML7213 is completely compatible for Intel EG20T PCH.
Signed-off-by: Tomoya MORINAGA <tomoya-linux@dsn.okisemi.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
|
|
* the GSM 07.10 specification says in 5.4.3.1 that
'both stations shall set the P bit to 0'
thanks to Alan Cox for finding this explanation in the spec
* without this fix, on Telit & Sim.com modems, opening a new DLC
randomly fails. Not setting PF bit of the control byte gives a
reliable behaviour on these modems.
Signed-off-by: Eric Bénard <eric@eukrea.com>
Cc: Alan Cox <alan@lxorguk.ukuu.org.uk>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
|
|
* this documentation gives some details on how to get the n_gsm
line discipline to work with modems supporting 07.10 basic option.
* it was tested on Telit and Simcom modems.
Signed-off-by: Eric Bénard <eric@eukrea.com>
Cc: Alan Cox <alan@lxorguk.ukuu.org.uk>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
|
|
This driver supports UART-DM HW on MSM platforms. It uses the on
chip DMA to drive data transfers and has optional support for UART
power management independent of Linux suspend/resume and wakeup
from Rx.
The driver was originally developed by Google. It is functionally
equivalent to the version available at:
http://android.git.kernel.org/?p=kernel/experimental.git
the differences being:
1) Remove wakelocks and change unsupported DMA API.
2) Replace clock selection register codes by macros.
3) Fix checkpatch errors and add inline documentation.
4) Add runtime PM hooks for active power state transitions.
5) Handle error path and cleanup resources if required.
CC: Nick Pelly <npelly@google.com>
Signed-off-by: Sankalp Bose <sankalpb@codeaurora.org>
Signed-off-by: Mayank Rana <mrana@codeaurora.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
|
|
The current tty_audit_add_data code:
do {
size_t run;
run = N_TTY_BUF_SIZE - buf->valid;
if (run > size)
run = size;
memcpy(buf->data + buf->valid, data, run);
buf->valid += run;
data += run;
size -= run;
if (buf->valid == N_TTY_BUF_SIZE)
tty_audit_buf_push_current(buf);
} while (size != 0);
If the current buffer is full, kernel will then call tty_audit_buf_push_current
to empty the buffer. But if we disabled audit at the same time, tty_audit_buf_push()
returns immediately if audit_enabled is zero. Without emptying the buffer.
With obvious effect on tty_audit_add_data() that ends up spinning in that loop,
copying 0 bytes at each iteration and attempting to push each time without any effect.
Holding the lock all along.
Suggested-by: Alexander Viro <aviro@redhat.com>
Signed-off-by: Xiaotian Feng <dfeng@redhat.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
|
|
The file is required by the specialix driver, which was
moved to drivers/staging/.
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
|
|
I forgot to move the digi*.h files from drivers/char/ to
drivers/staging/tty/
Thanks to Randy for pointing out the issue.
Reported-by: Randy Dunlap <randy.dunlap@oracle.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
|
|
The ioctl file pointer was removed in commit 6caa76
"tty: now phase out the ioctl file pointer for good".
Thus fix the prototype for mgslpc_ioctl() and eliminate below warning:
CC [M] drivers/char/pcmcia/synclink_cs.o
drivers/char/pcmcia/synclink_cs.c:2787: warning: initialization from incompatible pointer type
Signed-off-by: Axel Lin <axel.lin@gmail.com>
Cc: Alan Cox <alan@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
|
|
spin_lock_irqsave() is not nestable. The second time that it gets
called it overwrites the "flags" variable and so IRQs can't be restored
properly.
Signed-off-by: Dan Carpenter <error27@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
|
|
flush_scheduled_work() in tty_exit() doesn't seem to target any
specific work. If it was to flush work items used in tty generic
layer, they're already flushed properly during tty release.
flush_scheduled_work() is going away. Remove the seemingly redundant
usage.
Signed-off-by: Tejun Heo <tj@kernel.org>
Cc: Jiri Slaby <jslaby@suse.cz>
Cc: Alan Cox <alan@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
|
|
There is no need to test for a device_type property in ns8250
compatible serial ports. device_type is an OpenFirmware property that
is not required when using the flattened tree representation.
Signed-off-by: Grant Likely <grant.likely@secretlab.ca>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
|
|
Commit 728674a7e466628df2aeec6d11a2ae1ef968fb67
("tty: move hvc drivers to drivers/tty/hvc/")
moved the files, update the patterns as appropriate.
Signed-off-by: Joe Perches <joe@perches.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
|
|
The patch "tty: now phase out the ioctl file pointer for good" missed
the tty3270 driver. This is the missing piece.
Signed-off-by: Heiko Carstens <heiko.carstens@de.ibm.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
|
|
This caused a build error. Many thanks to Stephen Rothwell for pointing
this mistake out.
Reported-by: Stephen Rothwell <sfr@canb.auug.org.au>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
|
|
This was to resolve a merge issue with drivers/char/Makefile and
drivers/tty/serial/68328serial.c
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
|
|
Signed-off-by: Tomoya MORINAGA <tomoya-linux@dsn.okisemi.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
|
|
Signed-off-by: Tomoya MORINAGA <tomoya-linux@dsn.okisemi.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
|
|
Currently, auto-flow control setting processing is not set correctly.
This patch fixes the issue.
Signed-off-by: Tomoya MORINAGA <tomoya-linux@dsn.okisemi.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
|
|
Currently, uart clock is not set correctly.
This patch fixes the issue.
Signed-off-by: Tomoya MORINAGA <tomoya-linux@dsn.okisemi.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
|
|
For easy to understad which port the message is out,
replace pr_xxx with dev_xxx.
Signed-off-by: Tomoya MORINAGA <tomoya-linux@dsn.okisemi.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
|
|
Reduce memcpy for performance improvement.
Signed-off-by: Tomoya MORINAGA <tomoya-linux@dsn.okisemi.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
|
|
Currently, spin_lock is not initialized.
Thus, add spin_lock_init().
Signed-off-by: Tomoya MORINAGA <tomoya-linux@dsn.okisemi.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
|
|
Currently, this driver can handle only single scatterlist.
Thus, it can't send data beyond FIFO size.
This patch enables this driver can handle multiple scatter list.
Signed-off-by: Tomoya MORINAGA <tomoya-linux@dsn.okisemi.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
|
|
drivers/staging/generic_serial/
As planned by Arnd Bergmann, this moves the following drivers to the
drivers/staging/generic_serial directory where they will be removed
after 2.6.41 if no one steps up to claim them.
generic_serial
rio
ser_a2232
sx
vme_scc
Cc: Arnd Bergmann <arnd@arndb.de>
Cc: Alan Cox <alan@lxorguk.ukuu.org.uk>
Cc: Jiri Slaby <jslaby@suse.cz>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
|
|
As planned by Arnd Bergmann, this moves the following drivers to the
drivers/staging/tty/ directory where they will be removed after 2.6.41
if no one steps up to claim them.
epca
epca
ip2
istallion
riscom8
serial167
specialix
stallion
Cc: Arnd Bergmann <arnd@arndb.de>
Cc: Alan Cox <alan@lxorguk.ukuu.org.uk>
Cc: Jiri Slaby <jslaby@suse.cz>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
|
|
As planned by Arnd Bergmann, this moves the ipwireless driver to the
drivers/tty/ directory as that's where it really belongs.
Cc: Arnd Bergmann <arnd@arndb.de>
Cc: Alan Cox <alan@lxorguk.ukuu.org.uk>
Cc: Jiri Slaby <jslaby@suse.cz>
Cc: David Sterba <dsterba@suse.cz>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
|
|
As planned by Arnd Bergmann, this moves the following drivers from
drivers/char/ to drivers/tty/ as that's where they really belong:
amiserial
nozomi
synclink
rocket
cyclades
moxa
mxser
isicom
bfin_jtag_comm
Cc: Arnd Bergmann <arnd@arndb.de>
Cc: Alan Cox <alan@lxorguk.ukuu.org.uk>
Cc: Jiri Slaby <jslaby@suse.cz>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
|
|
port->flags is of type upf_t, which corresponds to UPF_* flags.
Signed-off-by: Tobias Klauser <tklauser@distanz.ch>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
|
|
This will make it easier to get the driver to support device tree. The
old platform data method is still supported though.
Also change the driver to use only one platform device per port.
Signed-off-by: Tobias Klauser <tklauser@distanz.ch>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
|
|
This is not even used in nios2 arch code anymore.
Signed-off-by: Tobias Klauser <tklauser@distanz.ch>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
|
|
This fixes a sparse warning.
Signed-off-by: Tobias Klauser <tklauser@distanz.ch>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
|
|
The three identical uart ports can work either in DMA or PIO mode. Adding such
a module parameter "hsu_dma_enable" will enable user to chose working modes for
each port. If the mfd driver is built in kernel, adding a "mfd.hsu_dma_enable=x"
in kernel command line has the same effect.
Signed-off-by: Feng Tang <feng.tang@intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
|
|
In A0 stepping, TX half-empty interrupt is not working, so have to
use the full-empty interrupts whose performance will be 15% lower.
Now re-enable the half-empty interrrupt after it is enabled in
silicon.
Signed-off-by: Feng Tang <feng.tang@intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
|
|
Alan missed the ia64 simulator serial driver (because it was hidden
in arch/... rather than located under drivers/... where one might
expect to find a driver). Drop the "file *" argument from rs_ioctl()
in arch/ia64/hp/sim/simserial.c
Signed-off-by: Tony Luck <tony.luck@intel.com>
Cc: Alan Cox <alan@lxorguk.ukuu.org.uk>,
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
|
|
The Kconfig options for the drivers/tty/ files still were hanging around
in the "big" drivers/char/Kconfig file, so move them to the proper
location under drivers/tty and drivers/tty/hvc/
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
|
|
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/ecryptfs/ecryptfs-2.6
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/ecryptfs/ecryptfs-2.6:
eCryptfs: Copy up lower inode attrs in getattr
ecryptfs: read on a directory should return EISDIR if not supported
eCryptfs: Handle NULL nameidata pointers
eCryptfs: Revert "dont call lookup_one_len to avoid NULL nameidata"
|
|
The current code does not follow Intel documentation: It misses some things
and does other, undocumented things. This causes wrong backlight values in
certain conditions. Instead of adding tricky code handling badly documented
and rare corner cases, don't handle combination mode specially at all. This
way PCI_LBPC is never touched and weird things shouldn't happen.
If combination mode is enabled, then the only downside is that changing the
brightness has a greater granularity (the LBPC value), but LBPC is at most
254 and the maximum is in the thousands, so this is no real functional loss.
A potential problem with not handling combined mode is that a brightness of
max * PCI_LBPC is not bright enough. However, this is very unlikely because
from the documentation LBPC seems to act as a scaling factor and doesn't look
like it's supposed to be changed after boot. The value at boot should always
result in a bright enough screen.
IMPORTANT: However, although usually the above is true, it may not be when
people ran an older (2.6.37) kernel which messed up the LBPC register, and
they are unlucky enough to have a BIOS that saves and restores the LBPC value.
Then a good kernel may seem to not work: Max brightness isn't bright enough.
If this happens people should boot back into the old kernel, set brightness
to the maximum, and then reboot. After that everything should be fine.
For more information see the below links. This fixes bugs:
http://bugzilla.kernel.org/show_bug.cgi?id=23472
http://bugzilla.kernel.org/show_bug.cgi?id=25072
Signed-off-by: Indan Zupancic <indan@nul.nu>
Tested-by: Alex Riesen <raa.lkml@gmail.com>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
|
|
We force particular alignment when we generate attribute structures
when generation MODULE_VERSION() data and we need to make sure that
this alignment is followed when we iterate over these structures,
otherwise we may crash on platforms whose natural alignment is not
sizeof(void *), such as m68k.
Reported-by: Geert Uytterhoeven <geert@linux-m68k.org>
Signed-off-by: Dmitry Torokhov <dtor@vmware.com>
[ There are more issues here, but the fixes are incredibly ugly - Linus ]
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/mjg59/platform-drivers-x86
* 'for_linus' of git://git.kernel.org/pub/scm/linux/kernel/git/mjg59/platform-drivers-x86:
dell-laptop: Toggle the unsupported hardware killswitch
thinkpad_acpi: Always report scancodes for hotkeys
acer-wmi: Fix capitalisation of GUID
platform/x86: ideapad-laptop depends on INPUT
platform: x86: acer-wmi: world-writable sysfs threeg file
platform: x86: asus_acpi: world-writable procfs files
platform: x86: tc1100-wmi: world-writable sysfs wireless and jogdial files
platform-drivers: x86: pmic: Use request_irq instead of chained handler
platform-drivers: x86: pmic: Use irq_chip buslock mechanism
platform-drivers: x86: Convert pmic to new irq_chip functions
platform-drivers: x86: pmic: Fix up bogus irq hackery
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/mmarek/kbuild-2.6
* 'rc-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/mmarek/kbuild-2.6:
fixdep: Do not record dependency on the source file itself
|
|
Add fs/eventfd.c to filesystems docbook.
Make typo corrections in fs/eventfd.c.
Signed-off-by: Randy Dunlap <randy.dunlap@oracle.com>
Cc: Davide Libenzi <davidel@xmailserver.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
|
|
Update the "log_buf_len" description to use [KMG] syntax for the
buffer size.
Signed-off-by: Randy Dunlap <randy.dunlap@oracle.com>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
|
|
The '[KMG]' suffix is commonly described after a number of kernel
parameter values documentation. Explicitly state its semantics.
Signed-off-by: Ahmed S. Darwish <darwish.07@gmail.com>
Signed-off-by: Randy Dunlap <randy.dunlap@oracle.com>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
|
|
Complete the crashkernel= kernel parameter documentation.
Signed-off-by: Ahmed S. Darwish <darwish.07@gmail.com>
Acked-by: Simon Horman <horms@verge.net.au>
Acked-by: Vivek Goyal <vgoyal@redhat.com>
Signed-off-by: Randy Dunlap <randy.dunlap@oracle.com>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/sage/ceph-client
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/sage/ceph-client:
ceph: keep reference to parent inode on ceph_dentry
ceph: queue cap_snaps once per realm
libceph: fix socket write error handling
libceph: fix socket read error handling
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/kgene/linux-samsung
* 's5p-fixes-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/kgene/linux-samsung:
ARM: S5PV210: Fix regulator names
ARM: S5PV210: Update max8998_platform_data
ARM: SAMSUNG: Drop exporting s3c24xx_ts_set_platdata
ARM: S5P: Fix end address in memory resource information for UART devices
ARM: S5P64X0: Cleanup map.h file
ARM: S5P6442: Cleanup map.h file
ARM: S5PC100: Clenaup map.h file
ARM: S5PV210: Cleanup map.h file
ARM: S5PV310: Cleanup map.h file
|
|
* git://git.kernel.org/pub/scm/linux/kernel/git/sfrench/cifs-2.6:
[CIFS] update cifs version
cifs: Fix regression in LANMAN (LM) auth code
cifs: fix handling of scopeid in cifs_convert_address
|
|
* 'fixes' of master.kernel.org:/home/rmk/linux-2.6-arm:
ARM: 6745/1: kprobes insn decoding fix
ARM: tlb: move noMMU tlb_flush() to asm/tlb.h
ARM: tlb: delay page freeing for SMP and ARMv7 CPUs
ARM: Keep exit text/data around for SMP_ON_UP
ARM: Ensure predictable endian state on signal handler entry
ARM: 6740/1: Place correctly notes section in the linker script
ARM: 6700/1: SPEAr: Correct SOC config base address for spear320
ARM: 6722/1: SPEAr: sp810: switch to slow mode before reset
ARM: 6712/1: SPEAr: replace readl(), writel() with relaxed versions in uncompress.h
ARM: 6720/1: SPEAr: Append UL to VMALLOC_END
ARM: 6676/1: Correct the cpu_architecture() function for ARMv7
ARM: 6739/1: update .gitignore for boot/compressed
ARM: 6743/1: errata: interrupted ICALLUIS may prevent completion of broadcasted operation
ARM: 6742/1: pmu: avoid setting IRQ affinity on UP systems
ARM: 6741/1: errata: pl310 cache sync operation may be faulty
|
|
* 'for-linus' of git://git390.marist.edu/pub/scm/linux-2.6:
[S390] net: provide architecture specific NET_SKB_PAD
[S390] atomic: use inline asm
[S390] correct ipl parameter block safe guard
[S390] atomic: use ACCESS_ONCE() for atomic_read()
[S390] dasd: correct device table
|
