| Age | Commit message (Collapse) | Author |
|---|
|
There are systems where video module known to work fine regardless
of broken _DOD and ignoring returned value here doesn't cause
any issues later. This should fix brightness controls on some laptops.
Bugzilla: https://bugzilla.kernel.org/show_bug.cgi?id=47861
Signed-off-by: Igor Murzov <e-mail@date.by>
Reviewed-by: Sergey V <sftp.mtuci@gmail.com>
Signed-off-by: Zhang Rui <rui.zhang@intel.com>
|
|
following were the errors reported
drivers/thermal/rcar_thermal.c: In function ‘rcar_thermal_probe’:
drivers/thermal/rcar_thermal.c:214:10: warning: passing argument 3 of ‘thermal_zone_device_register’ makes integer from pointer without a cast [enabled by default]
include/linux/thermal.h:166:29: note: expected ‘int’ but argument is of type ‘struct rcar_thermal_priv *’
drivers/thermal/rcar_thermal.c:214:10: error: too few arguments to function ‘thermal_zone_device_register’
include/linux/thermal.h:166:29: note: declared here
make[1]: *** [drivers/thermal/rcar_thermal.o] Error 1
make: *** [drivers/thermal/rcar_thermal.o] Error 2
with gcc version 4.6.3 (Ubuntu/Linaro 4.6.3-1ubuntu5)
Signed-off-by: Devendra Naga <develkernel412222@gmail.com>
Signed-off-by: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Signed-off-by: Zhang Rui <rui.zhang@intel.com>
|
|
If T4 configuration file gets loaded from the /lib/firmware/cxgb4/ directory
then offload capabilities of the cards were getting disabled during
initialization. Hence ULDs do not get an UP event from the LLD.
Signed-off-by: Jay Hernandez <jay@chelsio.com>
Signed-off-by: Vipul Pandya <vipul@chelsio.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Based on commit b27393aecf66199f5ddad37c302d3e0cfadbe6c0
Calling mdiobus_free without calling mdiobus_unregister causes
BUG_ON(). This patch fixes the issue.
The semantic patch that found this issue(http://coccinelle.lip6.fr/):
// <smpl>
@@
expression E;
@@
... when != mdiobus_unregister(E);
+ mdiobus_unregister(E);
mdiobus_free(E);
// </smpl>
Signed-off-by: Peter Senna Tschudin <peter.senna@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Based on commit b27393aecf66199f5ddad37c302d3e0cfadbe6c0
Calling mdiobus_free without calling mdiobus_unregister causes
BUG_ON(). This patch fixes the issue.
The semantic patch that found this issue(http://coccinelle.lip6.fr/):
// <smpl>
@@
expression E;
@@
... when != mdiobus_unregister(E);
+ mdiobus_unregister(E);
mdiobus_free(E);
// </smpl>
Signed-off-by: Peter Senna Tschudin <peter.senna@gmail.com>
Tested-by: Roland Stigge <stigge@antcom.de>
Tested-by: Alexandre Pereira da Silva <aletes.xgr@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Since commit 96bed4b9 (use FW 7.8.2) BRB HW block needs to be
initialized using fw values for all devices.
Otherwise ETS on 57712/578xx will not work.
Signed-off-by: Dmitry Kravkov <dmitry@broadcom.com>
Signed-off-by: Ariel Elior <ariele@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/rafael/linux-pm
Pull power management update from Rafael J. Wysocki:
"Change the email address of the powernow-k8 maintainer."
* tag 'pm-for-3.7-rc4' of git://git.kernel.org/pub/scm/linux/kernel/git/rafael/linux-pm:
cpufreq / powernow-k8: Change maintainer's email address
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/dtor/input
Pull input subsystem fixes from Dmitry Torokhov:
"Just a few driver fixes."
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/dtor/input:
Input: tsc40 - remove wrong announcement of pressure support
Input: lpc32xx-keys - select INPUT_MATRIXKMAP
Input: pxa27x_keypad - clear pending interrupts on keypad config
Input: wacom - correct bad Cintiq 24HD check
Input: wacom - add INPUT_PROP_DIRECT flag to Cintiq 24HD
Input: egalax_ts - get gpio from devicetree
|
|
Return errno - not an NFS4ERR_. This worked because NFS4ERR_ACCESS == EACCES.
Signed-off-by: Weston Andros Adamson <dros@netapp.com>
Signed-off-by: Trond Myklebust <Trond.Myklebust@netapp.com>
|
|
Pull more scsi target fixes from Nicholas Bellinger:
"This series is a second round of target fixes for v3.7-rc4 that have
come into target-devel over the last days, and are important enough to
be applied ASAP.
All are being CC'ed to stable. The most important two are:
- target: Re-add explict zeroing of INQUIRY bounce buffer memory to
fix a regression for handling zero-length payloads, a bug that went
during v3.7-rc1, and hit >= v3.6.3 stable. (nab + paolo)
- iscsi-target: Fix a long-standing missed R2T wakeup race in TX
thread processing when using a single queue slot. (Roland)
Thanks to Roland & PureStorage team for helping to track down this
long standing race with iscsi-target single queue slot operation.
Also, the tcm_fc(FCoE) regression bug that was observed recently with
-rc2 code has also been resolved with the cancel_delayed_work() return
bugfix (commit c0158ca64da5: "workqueue: cancel_delayed_work() should
return %false if work item is idle") now in -rc3. Thanks again to Yi
Zou, MDR, Robert Love @ Intel for helping to track this down."
* git://git.kernel.org/pub/scm/linux/kernel/git/nab/target-pending:
target: Fix incorrect usage of nested IRQ spinlocks in ABORT_TASK path
iscsi-target: Fix missed wakeup race in TX thread
target: Avoid integer overflow in se_dev_align_max_sectors()
target: Don't return success from module_init() if setup fails
target: Re-add explict zeroing of INQUIRY bounce buffer memory
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/groeck/linux-staging
Pull hwmon fixes from Guenter Roeck:
"An e-mail address update, and fix a compile error on SPARC"
* tag 'hwmon-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/groeck/linux-staging:
hwmon: Only include of_match_table with CONFIG_OF_GPIO
hwmon, fam15h_power: Change email address, MAINTAINERS entry
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/dhowells/linux-frv
Pull FRV fixes from David Howells:
"A collection of small fixes for the FRV architecture."
* tag 'frv-fixes-20121102' of git://git.kernel.org/pub/scm/linux/kernel/git/dhowells/linux-frv:
frv: fix the broken preempt
frv: switch to saner kernel_execve() semantics
FRV: Fix the new-style kernel_thread() stuff
FRV: Fix the preemption handling
FRV: gcc-4.1.2 also inlines weak functions
FRV: Don't objcopy the GNU build_id note
FRV: Add missing linux/export.h #inclusions
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/konrad/xen
Pull Xen bugfixes from Konrad Rzeszutek Wilk:
- Use appropriate macros instead of hand-rolling our own (ARM).
- Fixes if FB/KBD closed unexpectedly.
- Fix memory leak in /dev/gntdev ioctl calls.
- Fix overflow check in xenbus_file_write.
- Document cleanup.
- Performance optimization when migrating guests.
* tag 'stable/for-linus-3.7-rc4-tag' of git://git.kernel.org/pub/scm/linux/kernel/git/konrad/xen:
xen/mmu: Use Xen specific TLB flush instead of the generic one.
xen/arm: use the __HVC macro
xen/xenbus: fix overflow check in xenbus_file_write()
xen-kbdfront: handle backend CLOSED without CLOSING
xen-fbfront: handle backend CLOSED without CLOSING
xen/gntdev: don't leak memory from IOCTL_GNTDEV_MAP_GRANT_REF
x86: remove obsolete comment from asm/xen/hypervisor.h
|
|
This hashtable implementation is using hlist buckets to provide a simple
hashtable to prevent it from getting reimplemented all over the kernel.
Signed-off-by: Sasha Levin <levinsasha928@gmail.com>
[ Merging this now, so that subsystems can start applying Sasha's
patches that use this - Linus ]
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
|
|
Just get %icc2 into the state we would have after local_irq_disable()
and physical IRQ having happened since then. Then we can simply
use preempt_schedule_irq() and be done with the whole mess.
Acked-by: David Howells <dhowells@redhat.com>
Signed-off-by: Al Viro <viro@zeniv.linux.org.uk>
|
|
Signed-off-by: Al Viro <viro@zeniv.linux.org.uk>
|
|
The kernel_thread() changes for FRV don't work, and FRV fails to boot,
starting with:
commit 02ce496f152df87be081a64796498942c433a2fd
Author: Al Viro <viro@zeniv.linux.org.uk>
Date: Tue Sep 18 22:18:51 2012 -0400
Subject: frv: split ret_from_fork, simplify kernel_thread() a lot
The problem is that the userspace registers are completely cleared when a
kernel thread is created and all subsequent user threads are then copied from
that. Unfortunately, however, the TBR and PSR registers are restored from the
pt_regs and the values they should be set to are clobbered by the memset.
Instead, copy across the old user registers as normal, and then merely alter
GR8 and GR9 in it if we're going to execute a kernel thread.
Signed-off-by: David Howells <dhowells@redhat.com>
|
|
Fix the preemption handling in FRV code where the PREEMPT_ACTIVE value is
incorrectly loaded into the threadinfo flags rather than the threadinfo
preemption count.
Unfortunately, the code cannot be simply converted to use
preempt_schedule_irq() as is because FRV uses virtual interrupt disablement to
cut down on the cost of actually disabling interrupts and thus
local_irq_enable() doesn't actually enable interrupts.
Reported-by: Al Viro <viro@ZenIV.linux.org.uk>
Signed-off-by: David Howells <dhowells@redhat.com>
cc: Al Viro <viro@ZenIV.linux.org.uk>
|
|
gcc-4.1.2 inlines weak functions, which causes FRV to fail when the dummy
thread_info_cache_init() gets inlined into start_kernel().
Signed-off-by: David Howells <dhowells@redhat.com>
|
|
Don't let objcopy transfer the GNU build_id note into the loadable image as it
is located at address 0 and the image ends up >3G in size.
Signed-off-by: David Howells <dhowells@redhat.com>
|
|
Add missing linux/export.h #inclusions to the FRV arch.
Signed-off-by: David Howells <dhowells@redhat.com>
|
|
When watching the irqs name of tegra i2c, all instances
irq name shows as tegra_i2c.
Passing the device name properly to have the irq names with
instance like tegra-i2c.0, tegra-i2c.1 etc.
Signed-off-by: Laxman Dewangan <ldewangan@nvidia.com>
Acked-by: Jean Delvare <khali@linux-fr.org>
Signed-off-by: Wolfram Sang <w.sang@pengutronix.de>
|
|
Make sure to clk_prepare as well as clk_enable.
Signed-off-by: Philippe Begnic <philippe.begnic@stericsson.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Wolfram Sang <w.sang@pengutronix.de>
|
|
This I2C master can do DMA and PIOQUEUE (PIO with FIFO). Originally,
only PIOQUEUE was supported and it had issues, then DMA support was added
this cycle. The original intention was to keep PIOQUEUE since it has
less overhead what is nice for small transfers. However, runtime
switching between PIOQEUE and DMA depending on the transfer size never
worked despite a lot of trying. Since PIOQUEUE mode itself was flaky
(polling at places where interrupts failed to work) and the
implementation also imposed a size limit for transfers, it is best to
remove the support, so users don't fall over its limitations. It also
makes the driver a lot cleaner and more robust. If somebody really wants
less overhead, plain PIO mode could still be implemented with the
addidtional advantage that this mode is also available on MX23, too.
Signed-off-by: Wolfram Sang <w.sang@pengutronix.de>
Reviewed-by: Marek Vasut <marex@denx.de>
|
|
Pull Xtensa fixes from Chris Zankel:
"Some important bug fixes.
With the change to uapi, there was a bug introduced that results in an
empty syscall table (mult-inclusion bug). Switching to the generic
thread/execve allowed us to fix a bug we had in vfork()."
* tag 'xtensa-next-20121101' of git://github.com/czankel/xtensa-linux:
xtensa: switch to generic sys_execve()
xtensa: switch to generic kernel_execve()
xtensa: switch to generic kernel_thread()
xtensa: reset windowbase/windowstart when cloning the VM
xtensa: use physical addresses for bus addresses
xtensa: allow multi-inclusion for uapi/unistd.h
|
|
When buffer sharing with the i915 and using a 1680x1050 monitor,
the i915 gives is a 6912 buffer for the 6720 width, the code doesn't
render this properly as it uses one value to set the base address for
reading from the vmap and for where to start on the device.
This fixes it by calculating the values correctly for the device and
for the pixmap. No idea how I haven't seen this before now.
Cc: stable@vger.kernel.org
Signed-off-by: Dave Airlie <airlied@redhat.com>
|
|
The following fixes build errors on sparc. Without any DT support,
of_match_ptr is NULL and the below is a no-op. However, if just
CONFIG_OF is defined then so is of_match_ptr.
All useful parts of the gpio-fan DT support rely on CONFIG_OF_GPIO
anyway, so of_match_table should too.
Signed-off-by: Jamie Lentin <jm@lentin.co.uk>
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/daeinki/drm-exynos into drm-fixes
Inki writes:
"As I posted before, we have added a new git repository for Exynos drm
to MAINTAINERS file so change it to new one like below,
from git://git.infradead.org/users/kmpark/linux-samsung
to git://git.kernel.org/pub/scm/linux/kernel/git/daeinki/drm-exynos
And this pull request includes the following:
- fix display on issue when user requested dpms mode changing.
- add git repository for Exynos drm to MAINTAINERS file.
- add support for ARCH_MULTIPLATFORM.
- and code clean."
* 'exynos-drm-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/daeinki/drm-exynos:
drm: exynos: removed warning due to missing typecast for mixer driver data
drm/exynos: add support for ARCH_MULTIPLATFORM
MAINTAINERS: Add git repository for Exynos DRM
drm/exynos: fix display on issue
|
|
into drm-fixes
Alex writes:
"This request is mostly load detection fixes from Egbert and me."
* 'drm-fixes-3.7' of git://people.freedesktop.org/~agd5f/linux:
drm/radeon: add load detection support for ext DAC on R200 (v2)
DRM/radeon: For single CRTC GPUs move handling of CRTC_CRT_ON to crtc_dpms().
DRM/Radeon: Fix TV DAC Load Detection for single CRTC chips.
DRM/Radeon: Clean up code in TV DAC load detection.
drm/radeon: fix ATPX function documentation
drivers/gpu/drm/radeon/evergreen_cs.c: Remove unnecessary semicolon
DRM/Radeon: On DVI-I use Load Detection when EDID is bogus.
DRM/Radeon: Fix primary DAC Load Detection for RV100 chips.
DRM/Radeon: Fix Load Detection on legacy primary DAC.
|
|
git://people.freedesktop.org/~danvet/drm-intel into drm-fixes
Daniel Vetter writes"
Nothing big at all for -fixes, just small stuff:
- Two patches to fix bugs on i830M
- ums regression fixer due to kicking firmeware fbs (Chris)
- tune down a too loud warning (Jani)
- be more careful with sdvo infoframes, which fixes a long-standing
sdvo-hdmi regression"
* 'drm-intel-fixes' of git://people.freedesktop.org/~danvet/drm-intel:
drm/i915: Only kick out vesafb if we takeover the fbcon with KMS
drm/i915: be less verbose about inability to provide vendor backlight
drm/i915: clear the entire sdvo infoframe buffer
drm/i915: VGA needs to be on pipe A on i830M
drm/i915: fix overlay on i830M
|
|
Signed-off-by: Trond Myklebust <Trond.Myklebust@netapp.com>
|
|
Fix double sizeof when parsing IPv6 address from
user space because it breaks get/del by specific IPv6 address.
Problem noticed by David Binderman:
https://bugzilla.kernel.org/show_bug.cgi?id=49171
Signed-off-by: Julian Anastasov <ja@ssi.bg>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Reading TCP stats when using TCP Illinois congestion control algorithm
can cause a divide by zero kernel oops.
The division by zero occur in tcp_illinois_info() at:
do_div(t, ca->cnt_rtt);
where ca->cnt_rtt can become zero (when rtt_reset is called)
Steps to Reproduce:
1. Register tcp_illinois:
# sysctl -w net.ipv4.tcp_congestion_control=illinois
2. Monitor internal TCP information via command "ss -i"
# watch -d ss -i
3. Establish new TCP conn to machine
Either it fails at the initial conn, or else it needs to wait
for a loss or a reset.
This is only related to reading stats. The function avg_delay() also
performs the same divide, but is guarded with a (ca->cnt_rtt > 0) at its
calling point in update_params(). Thus, simply fix tcp_illinois_info().
Function tcp_illinois_info() / get_info() is called without
socket lock. Thus, eliminate any race condition on ca->cnt_rtt
by using a local stack variable. Simply reuse info.tcpv_rttcnt,
as its already set to ca->cnt_rtt.
Function avg_delay() is not affected by this race condition, as
its called with the socket lock.
Cc: Petr Matousek <pmatouse@redhat.com>
Signed-off-by: Jesper Dangaard Brouer <brouer@redhat.com>
Acked-by: Eric Dumazet <edumazet@google.com>
Acked-by: Stephen Hemminger <shemminger@vyatta.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Correct spelling typo in net/sctp/socket.c
Signed-off-by: Masanari Iida <standby24x7@gmail.com>
Acked-by: Vlad Yasevich <vyasevich@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Fix off-by-one error because IFNAMSIZ == 16 and when this
code gets executed we stick a NULL byte where we should not.
How to reproduce:
with CONFIG_CC_STACKPROTECTOR=y (otherwise it may pass by silently)
modprobe bonding; echo 1 > /sys/class/net/bond0/bonding/mode;
echo "AAAAAAAAAAAAAAAA" > /sys/class/net/bond0/bonding/active_slave;
Signed-off-by: Nikolay Aleksandrov <nikolay@redhat.com>
Note: Sorry for the second patch but I missed this one while checking
the file. You can squash them into one patch.
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Fix off-by-one error because IFNAMSIZ == 16 and when this
code gets executed we stick a NULL byte where we should not.
How to reproduce:
with CONFIG_CC_STACKPROTECTOR=y (otherwise it may pass by silently)
modprobe bonding; echo 1 > /sys/class/net/bond0/bonding/mode;
echo "AAAAAAAAAAAAAAAA" > /sys/class/net/bond0/bonding/primary;
Signed-off-by: Nikolay Aleksandrov <nikolay@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
The one and only caller (in fs/nfs/nfs4client.c) uses the result
as an errno and would have interpreted an error as EPERM.
Signed-off-by: Weston Andros Adamson <dros@netapp.com>
Signed-off-by: Trond Myklebust <Trond.Myklebust@netapp.com>
|
|
Signed-off-by: Dmitry Kravkov <dmitry@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Since the Warpcore supports various link types, need to set only the correct
supported modes for XFI which is the serdes interface for the 10G-baseT PHY.
Signed-off-by: Yaniv Rosner <yanivr@broadcom.com>
Signed-off-by: Barak Witkowski <barak@broadcom.com>
Signed-off-by: Dmitry Kravkov <dmitry@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
When SFP+ module is plugged in after driver is already loaded, it may not be
recognized, so set SFP module recognition time up to 300ms, without resetting
the module power in the middle.
Signed-off-by: Yaniv Rosner <yanivr@broadcom.com>
Signed-off-by: Barak Witkowski <barak@broadcom.com>
Signed-off-by: Dmitry Kravkov <dmitry@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Fix possible incorrect link speed provision following rapid link speed change.
Clear link speed mask after each link change, and not only after link down.
Signed-off-by: Yaniv Rosner <yanivr@broadcom.com>
Signed-off-by: Barak Witkowski <barak@broadcom.com>
Signed-off-by: Dmitry Kravkov <dmitry@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Several KR registers were not set correctly back to default after
loopback test, so set those global registers over the global WC lane (zero)
rather than the current lane.
Signed-off-by: Yaniv Rosner <yanivr@broadcom.com>
Signed-off-by: Barak Witkowski <barak@broadcom.com>
Signed-off-by: Dmitry Kravkov <dmitry@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
In case of link flap avoidance between PXE boot and bnx2x, set the appropriate
PHY DEVAD even if LFA kicks in.
Signed-off-by: Yaniv Rosner <yanivr@broadcom.com>
Signed-off-by: Barak Witkowski <barak@broadcom.com>
Signed-off-by: Dmitry Kravkov <dmitry@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Fix 1G KR link by restoring CL72 misc control register to default value rather
than 0.
Signed-off-by: Yaniv Rosner <yanivr@broadcom.com>
Signed-off-by: Barak Witkowski <barak@broadcom.com>
Signed-off-by: Dmitry Kravkov <dmitry@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Pull KVM fix from Marcelo Tosatti.
* git://git.kernel.org/pub/scm/virt/kvm/kvm:
KVM: x86: fix vcpu->mmio_fragments overflow
|
|
This patch corrects the ethtool get_ts_info functon which did not state that
software timestamping was supported, even though it is.
Signed-off-by: Jacob Keller <jacob.e.keller@intel.com>
CC: Stable <stable@vger.kernel.org> [3.5]
Tested-by: Stephen Ko <stephen.s.ko@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
The R200 asics use an external DAC for the secondary DAC.
The current KMS code tries to use code for the integrated
TV DAC for R200 which leads to unpredictable results since
R200 does not have an integrated TV DAC. This patch ports
the external DAC load detection support from the UMS
driver to KMS.
v2: fix typo in loop break logic
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Reviewed-by: Egbert Eich <eich@suse.de>
|
|
On all dual CRTC GPUs the CRTC_CRT_ON in the RADEON_CRTC_EXT_CNTL register
controls the CRTC of the primary DAC. Therefore it is set in the DAC DMPS
function.
This is different for GPU's with a single CRTC but a primary and a
TV DAC: here it controls the single CRTC no matter where it is routed.
Therefore we set it here. This avoids an elaborate on/off state tracking
since both primary_dac_dpms() and tv_dac_dpms() functions would have
to touch this bit.
On single CRTC GPUs with just one DAC it's irrelevant where this bit
is handled.
agd5f: fix warning
Signed-off-by: Egbert Eich <eich@suse.de>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
|
|
The RN50 has a TV DAC but only a single CRTC. For load detection this
DAC is controlled by the primary CRTC.
Signed-off-by: Egbert Eich <eich@suse.de>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
|
|
Signed-off-by: Egbert Eich <eich@suse.de>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
|
