| Age | Commit message (Collapse) | Author |
|---|
|
This fixes a DMA mapping leakage in the case where we reject a DMA buffer
because of its address.
The patch by Michael Buesch has been ported to b43legacy.
Signed-off-by: Stefano Brivio <stefano.brivio@polimi.it>
Cc: Christian Casteyde <casteyde.christian@free.fr>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
|
|
Some people are getting this message a lot, and we have traced it to
broken access points that much too often send completely empty frames
(all bytes zeroed, which they shouldn't do at all.)
Since we cannot do anything about such frames in any case except the
special case where we're debugging an AP, just remove the message.
Signed-off-by: Johannes Berg <johannes@sipsolutions.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
|
|
Add the tree entry for rt2x00 to inform people about the
rt2x00.git tree.
Signed-off-by: Ivo van Doorn <IvDoorn@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
|
|
I have been acting as the maintainer since the rfkill introduction,
so lets make it official by adding a rfkill entry in the MAINTAINERS file.
Signed-off-by: Ivo van Doorn <IvDoorn@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
|
|
rfkill_switch_all() is supposed to only switch all the interfaces of a
given type, but does not actually do this; instead, it just switches
everything currently in the same state.
Add the necessary type check in.
(This fixes a bug I've been seeing while developing an rfkill laptop
driver, with both bluetooth and wireless simultaneously changing state
after only pressing either KEY_WLAN or KEY_BLUETOOTH).
Signed-off-by: Carlos Corbacho <carlos@strangeworlds.co.uk>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
|
|
This fixes b43legacy for the SSB DMA API change.
Signed-off-by: Michael Buesch <mb@bu3sch.de>
Cc: Stefano Brivio <stefano.brivio@polimi.it>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
|
|
This fixes DMA on architectures where DMA is nontrivial, like PPC64.
We must use the host-device's (PCI) struct device for any DMA
operation instead of the SSB device. For this we add a new
struct device pointer to the SSB device structure that will always
point to the right device for DMAing.
Without this patch b43 and b44 drivers won't work on complex-DMA
architectures, that for example need dev->archdata for DMA operations.
Signed-off-by: Michael Buesch <mb@bu3sch.de>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
|
|
Signed-off-by: Reinette Chatre <reinette.chatre@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
|
|
This allows for the correct initial values to be uploaded to bcm4303
devices. It should be correct, but I can't reliably test this as I suspect
there's something going wrong with an hardware rfkill switch on my laptop.
Please test.
Signed-off-by: Stefano Brivio <stefano.brivio@polimi.it>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
|
|
This adds missing priv->vif assignments after "mac80211: don't use
interface indices in drivers" change. As rtl8180, rtl8187 also needs
priv->vif to be set, as without this an oops can happen in rtl8187_tx
function (priv->vif is passed to ieee80211_rts_duration).
Signed-off-by: Herton Ronaldo Krzesinski <herton@mandriva.com.br>
Acked-by: Pavel Roskin <proski@gnu.org>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
|
|
* git://git.kernel.org/pub/scm/linux/kernel/git/lethal/sh-2.6.25:
sh: export empty_zero_page
sh: arch/sh/kernel/traps_32.c needs asm/fpu.h
sh: fix compressed kernel build
sh64: add missing #include <asm/fpu.h>'s
|
|
ERROR: "empty_zero_page" [fs/ext4/ext4dev.ko] undefined!
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
|
|
arch/sh/kernel/traps_32.c: In function `do_reserved_inst':
arch/sh/kernel/traps_32.c:667: error: implicit declaration of function `do_fpu_inst'
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
|
|
commit 54a015104136974262afa4b8ddd943ea70dec8a2 broke zImage build on sh arch:
LD vmlinux
SYSMAP System.map
SYSMAP .tmp_System.map
AS arch/sh/boot/compressed/head_32.o
In file included from /k/arch/sh/boot/compressed/head_32.S:11:
/k/include/linux/linkage.h:34: error: syntax error in macro parameter list
Fix it for both sh and sh64.
Signed-off-by: Manuel Lauss <mano@roarinelk.homelinux.net>
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
|
|
This patch fixes some compile errors due to missing save_fpu()
prototypes on sh64 caused by
commit 9bbafce2eec190ef7e44b0eb1095ba17ce6ad3af
(sh: Fix occasional FPU register corruption under preempt).
Signed-off-by: Adrian Bunk <adrian.bunk@movial.fi>
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
|
|
Signed-off-by: Jens Axboe <jens.axboe@oracle.com>
|
|
Since 0bcc1816188e570bde1d56a208996660f2633ae0 (netconsole: Support
dynamic reconfiguration using configfs), the netconsole is always
registered, regardless of whether the user actually specified a
netconsole configuration on the command line.
However because netconsole has CON_PRINTBUFFER set, when it is
registered it causes the printk buffer to be replayed to all consoles.
When there is no netconsole configured this is a) pointless, and b)
somewhat annoying for the user of the existing console.
So instead we should only set CON_PRINTBUFFER if there is a netconsole
configuration found on the command line. This retains the existing
behaviour if a netconsole is setup by the user, and avoids spamming
other consoles when we're only registering for the dynamic
netconsole case.
Signed-off-by: Michael Ellerman <michael@ellerman.id.au>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
The struct sockaddr_can has been simplified in the code review
process. This patch updates this simplification also in the
associated documentation in can.txt .
Signed-off-by: Oliver Hartkopp <oliver@hartkopp.net>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
https://www.isdn4linux.de/mailman/listinfo/isdn4linux: "To prevent spamming,
you have to subscribe first. Mails from non-members are silently ignored!"
Signed-off-by: Paul Bolle <pebolle@tiscali.nl>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
tcp_prune_queue() doesn't prune an out-of-order queue at all.
Therefore sk_rmem_schedule() can fail but the out-of-order queue isn't
pruned . This can lead to tcp deadlock state if the next two
conditions are held:
1. There are a sequence hole between last received in
order segment and segments enqueued to the out-of-order queue.
2. Size of all segments in the out-of-order queue is more than tcp_mem[2].
Signed-off-by: Vitaliy Gusev <vgusev@openvz.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Thanks to Nikanth Karthikesan <knikanth@suse.de> for reporting this.
Signed-off-by: Jens Axboe <jens.axboe@oracle.com>
|
|
write_begin
This fixes a regression introduced in commit
205c109a7a96d9a3d8ffe64c4068b70811fef5e8 when switching to
write_begin/write_end operations in JFFS2.
The page offset is miscalculated, leading to corruption of the fragment
lists and subsequently to memory corruption and panics.
[ Side note: the bug is a fairly direct result of the naming. Nick was
likely misled by the use of "offs", since we tend to use the notion of
"offset" not as an absolute position, but as an offset _within_ a page
or allocation.
Alternatively, a "pgoff_t" is a page index, but not a byte offset -
our VM naming can be a bit confusing.
So in this case, a VM person would likely have called this a "pos",
not an "offs", or perhaps talked about byte offsets rather than page
offsets (since it's counted in bytes, not pages). - Linus ]
Signed-off-by: Alexey Korolev <akorolev@infradead.org>
Signed-off-by: Vasiliy Leonenko <vasiliy.leonenko@mail.ru>
Signed-off-by: David Woodhouse <dwmw2@infradead.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
|
|
TC_H_MAJ(parentid) for root classes is the same as for ingress, and if
ingress qdisc is created qdisc_lookup() returns its pointer (without
ingress NULL is returned). After this all qdisc_lookups give the same,
and we get endless loop. (I don't know how this could hide for so long
- it should trigger with every leaf class deleted if it's qdisc isn't
empty.)
After this fix qdisc_lookup() is omitted both for ingress and root
parents, but looking for root is only wasting a little time here...
Many thanks to Enrico Demarin for finding a test for catching this
bug, which probably bothered quite a lot of admins.
Reported-by: Enrico Demarin <enrico@superclick.com>,
Signed-off-by: Jarek Poplawski <jarkao2@gmail.com>
Acked-by: Patrick McHardy <kaber@trash.net>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Miklos Szeredi found the bug:
"Basically what happens is that on the server nlm_fopen() calls
nfsd_open() which returns -EACCES, to which nlm_fopen() returns
NLM_LCK_DENIED.
"On the client this will turn into a -EAGAIN (nlm_stat_to_errno()),
which in will cause fcntl_setlk() to retry forever."
So, for example, opening a file on an nfs filesystem, changing
permissions to forbid further access, then trying to lock the file,
could result in an infinite loop.
And Trond Myklebust identified the culprit, from Marc Eshel and I:
7723ec9777d9832849b76475b1a21a2872a40d20 "locks: factor out
generic/filesystem switch from setlock code"
That commit claimed to just be reshuffling code, but actually introduced
a behavioral change by calling the lock method repeatedly as long as it
returned -EAGAIN.
We assumed this would be safe, since we assumed a lock of type SETLKW
would only return with either success or an error other than -EAGAIN.
However, nfs does can in fact return -EAGAIN in this situation, and
independently of whether that behavior is correct or not, we don't
actually need this change, and it seems far safer not to depend on such
assumptions about the filesystem's ->lock method.
Therefore, revert the problematic part of the original commit. This
leaves vfs_lock_file() and its other callers unchanged, while returning
fcntl_setlk and fcntl_setlk64 to their former behavior.
Signed-off-by: J. Bruce Fields <bfields@citi.umich.edu>
Tested-by: Miklos Szeredi <mszeredi@suse.cz>
Cc: Trond Myklebust <trond.myklebust@fys.uio.no>
Cc: Marc Eshel <eshel@almaden.ibm.com>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/mingo/linux-2.6-sched-devel
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/mingo/linux-2.6-sched-devel:
revert "sched: fix fair sleepers"
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/jgarzik/libata-dev
* 'upstream-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/jgarzik/libata-dev:
[libata] make ali_atapi_dma static
[libata] sata_svw: fix reversed port count
|
|
* git://git.kernel.org/pub/scm/linux/kernel/git/davem/net-2.6: (31 commits)
[BRIDGE]: Fix crash in __ip_route_output_key with bridge netfilter
[NETFILTER]: ipt_CLUSTERIP: fix race between clusterip_config_find_get and _entry_put
[IPV6] ADDRCONF: Don't generate temporary address for ip6-ip6 interface.
[IPV6] ADDRCONF: Ensure disabling multicast RS even if privacy extensions are disabled.
[IPV6]: Use appropriate sock tclass setting for routing lookup.
[IPV6]: IPv6 extension header structures need to be packed.
[IPV6]: Fix ipv6 address fetching in raw6_icmp_error().
[NET]: Return more appropriate error from eth_validate_addr().
[ISDN]: Do not validate ISDN net device address prior to interface-up
[NET]: Fix kernel-doc for skb_segment
[SOCK] sk_stamp: should be initialized to ktime_set(-1L, 0)
net: check for underlength tap writes
net: make struct tun_struct private to tun.c
[SCTP]: IPv4 vs IPv6 addresses mess in sctp_inet[6]addr_event.
[SCTP]: Fix compiler warning about const qualifiers
[SCTP]: Fix protocol violation when receiving an error lenght INIT-ACK
[SCTP]: Add check for hmac_algo parameter in sctp_verify_param()
[NET_SCHED] cls_u32: refcounting fix for u32_delete()
[DCCP]: Fix skb->cb conflicts with IP
[AX25]: Potential ax25_uid_assoc-s leaks on module unload.
...
|
|
Correctly determine the address of an illegal instruction. The EPCR0 register
holds this value (masked by EPCR0_PC) if the validity bit is set (masked by
EPCR0_V). So the test as to whether the contents of the register are usable
should be involve checking the _V bit, not the _PC bits.
Signed-off-by: David Howells <dhowells@redhat.com>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
|
|
revert "sched: fix fair sleepers" (e22ecef1d2658ba54ed7d3fdb5d60829fb434c23),
because it is causing audio skipping, see:
http://bugzilla.kernel.org/show_bug.cgi?id=10428
the patch is correct and the real cause of the skipping is not
understood (tracing makes it go away), but time has run out so we'll
revert it and re-try in 2.6.26.
Signed-off-by: Ingo Molnar <mingo@elte.hu>
|
|
The bridge netfilter code attaches a fake dst_entry with a pointer to a
fake net_device structure to skbs it passes up to IPv4 netfilter. This
leads to crashes when the skb is passed to __ip_route_output_key when
dereferencing the namespace pointer.
Since bridging can currently only operate in the init_net namespace,
the easiest fix for now is to initialize the nd_net pointer of the
fake net_device struct to &init_net.
Should fix bugzilla 10323: http://bugzilla.kernel.org/show_bug.cgi?id=10323
Signed-off-by: Patrick McHardy <kaber@trash.net>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
_entry_put
Consider we are putting a clusterip_config entry with the "entries"
count == 1, and on the other CPU there's a clusterip_config_find_get
in progress:
CPU1: CPU2:
clusterip_config_entry_put: clusterip_config_find_get:
if (atomic_dec_and_test(&c->entries)) {
/* true */
read_lock_bh(&clusterip_lock);
c = __clusterip_config_find(clusterip);
/* found - it's still in list */
...
atomic_inc(&c->entries);
read_unlock_bh(&clusterip_lock);
write_lock_bh(&clusterip_lock);
list_del(&c->list);
write_unlock_bh(&clusterip_lock);
...
dev_put(c->dev);
Oops! We have an entry returned by the clusterip_config_find_get,
which is a) not in list b) has a stale dev pointer.
The problems will happen when the CPU2 will release the entry - it
will remove it from the list for the 2nd time, thus spoiling it, and
will put a stale dev pointer.
The fix is to make atomic_dec_and_test under the clusterip_lock.
Signed-off-by: Pavel Emelyanov <xemul@openvz.org>
Signed-off-by: Patrick McHardy <kaber@trash.net>
|
|
As far as I can remember, I was going to disable privacy extensions
on all "tunnel" interfaces. Disable it on ip6-ip6 interface as well.
Also, just remove ifdefs for SIT for simplicity.
Signed-off-by: YOSHIFUJI Hideaki <yoshfuji@linux-ipv6.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
are disabled.
Signed-off-by: YOSHIFUJI Hideaki <yoshfuji@linux-ipv6.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Signed-off-by: YOSHIFUJI Hideaki <yoshfuji@linux-ipv6.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
struct ipv6_opt_hdr is the common structure for IPv6 extension
headers, and it is common to increment the pointer to get
the real content. On the other hand, since the structure
consists only of 1-byte next-header field and 1-byte length
field, size of that structure depends on architecture; 2 or 4.
Add "packed" attribute to get 2.
Signed-off-by: YOSHIFUJI Hideaki <yoshfuji@linux-ipv6.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Fixes kernel bugzilla 10437
Based almost entirely upon a patch by Dmitry Butskoy.
When deciding what raw sockets to deliver the ICMPv6
to, we should use the addresses in the ICMPv6 quoted
IPV6 header, not the top-level one.
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Paul Bolle wrote:
> http://bugzilla.kernel.org/show_bug.cgi?id=9923 would have been much easier to
> track down if eth_validate_addr() would somehow complain aloud if an address
> is invalid. Shouldn't it make at least some noise?
I guess it should return -EADDRNOTAVAIL similar to eth_mac_addr()
when validation fails.
Signed-off-by: Patrick McHardy <kaber@trash.net>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Commit bada339 (Validate device addr prior to interface-up) caused a regression
in the ISDN network code, see: http://bugzilla.kernel.org/show_bug.cgi?id=9923
The trivial fix is to remove the pointer to eth_validate_addr() in the
net_device struct in isdn_net_init().
Signed-off-by: Paul Bolle <pebolle@tiscali.nl>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
The kernel-doc comment for skb_segment is clearly wrong. This states
what it actually does.
Signed-off-by: Ben Hutchings <bhutchings@solarflare.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Problem spotted by Andrew Brampton
Signed-off-by: Eric Dumazet <dada1@cosmosbay.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
If the user gives a packet under 14 bytes, we'll end up reading off the end
of the skb (not oopsing, just reading off the end).
Signed-off-by: Rusty Russell <rusty@rustcorp.com.au>
Acked-by: Max Krasnyanskiy <maxk@qualcomm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
There's no reason for this to be in the header, and it just hurts
recompile time.
Signed-off-by: Rusty Russell <rusty@rustcorp.com.au>
Acked-by: Max Krasnyanskiy <maxk@qualcomm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
All IP addresses that are present in a system are duplicated on
struct sctp_sockaddr_entry. They are linked in the global list
called sctp_local_addr_list. And this struct unions IPv4 and IPv6
addresses.
So, there can be rare case, when a sockaddr_in.sin_addr coincides
with the corresponding part of the sockaddr_in6 and the notifier
for IPv4 will carry away an IPv6 entry.
The fix is to check the family before comparing the addresses.
Signed-off-by: Pavel Emelyanov <xemul@openvz.org>
Signed-off-by: Vlad Yasevich <vladislav.yasevich@hp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Fix 3 warnings about discarding const qualifiers:
net/sctp/ulpevent.c:862: warning: passing argument 1 of 'sctp_event2skb' discards qualifiers from pointer target type
net/sctp/sm_statefuns.c:4393: warning: passing argument 1 of 'SCTP_ASOC' discards qualifiers from pointer target type
net/sctp/socket.c:5874: warning: passing argument 1 of 'cmsg_nxthdr' discards qualifiers from pointer target type
Signed-off-by: Vlad Yasevich <vladislav.yasevich@hp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
When receiving an error length INIT-ACK during COOKIE-WAIT,
a 0-vtag ABORT will be responsed. This action violates the
protocol apparently. This patch achieves the following things.
1 If the INIT-ACK contains all the fixed parameters, use init-tag
recorded from INIT-ACK as vtag.
2 If the INIT-ACK doesn't contain all the fixed parameters,
just reflect its vtag.
Signed-off-by: Gui Jianfeng <guijianfeng@cn.fujitsu.com>
Signed-off-by: Vlad Yasevich <vladislav.yasevich@hp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
RFC 4890 has the following text:
The HMAC algorithm based on SHA-1 MUST be supported and
included in the HMAC-ALGO parameter.
As a result, we need to check in sctp_verify_param() that HMAC_SHA1 is
present in the list. If not, we should probably treat this as a
protocol violation.
It should also be a protocol violation if the HMAC parameter is empty.
Signed-off-by: Wei Yongjun <yjwei@cn.fujitsu.com>
Signed-off-by: Vlad Yasevich <vladislav.yasevich@hp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Deleting of nonroot hnodes mostly doesn't work in u32_delete():
refcnt == 1 is expected, but such hnodes' refcnts are initialized
with 0 and charged only with "link" nodes. Now they'll start with
1 like usual. Thanks to Patrick McHardy for an improving suggestion.
Signed-off-by: Jarek Poplawski <jarkao2@gmail.com>
Acked-by: Jamal Hadi Salim <hadi@cyberus.ca>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
dev_queue_xmit() and the other IP output functions expect to get a skb
with clear or properly initialized skb->cb. Unlike TCP and UDP, the
dccp_skb_cb doesn't contain a struct inet_skb_parm at the beginning,
so the DCCP-specific data is interpreted by the IP output functions.
This can cause false negatives for the conditional POST_ROUTING hook
invocation, making the packet bypass the hook.
Add a inet_skb_parm/inet6_skb_parm union to the beginning of
dccp_skb_cb to avoid clashes. Also add a BUILD_BUG_ON to make
sure it fits in the cb.
[ Combined with patch from Gerrit Renker to remove two now unnecessary
memsets of IPCB(skb)->opt ]
Signed-off-by: Patrick McHardy <kaber@trash.net>
Acked-by: Arnaldo Carvalho de Melo <acme@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
The ax25_uid_free call walks the ax25_uid_list and releases entries
from it. The problem is that after the fisrt call to hlist_del_init
the hlist_for_each_entry (which hides behind the ax25_uid_for_each)
will consider the current position to be the last and will return.
Thus, the whole list will be left not freed.
Signed-off-by: Pavel Emelyanov <xemul@openvz.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
The driver stores the PCI resource addresses into 'unsigned long' variable
before calling ioremap_nocache() on them. This warrants kernel oops when the
registers are accessed on PPC 44x platforms which (being 32-bit) have PCI
memory space mapped beyond 4 GB.
The arch/ppc/ kernel has a fixup in ioremap() that creates an illusion that
the PCI memory resource is mapped below 4 GB, but arch/powerpc/ code got rid
of this trick, having instead CONFIG_RESOURCES_64BIT enabled.
[ Bump driver version and release date -DaveM ]
Signed-off-by: Sergei Shtylyov <sshtylyov@ru.mvista.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
