| Age | Commit message (Collapse) | Author |
|---|
|
The EDGE Port module of some ColdFire parts using the intc-2 interrupt
controller provides support for 7 external interrupts. These interrupts
go off-chip (that is they are not for internal peripherals). They need
some special handling and have some extra setup registers. Add code to
support them.
Signed-off-by: Greg Ungerer <gerg@uclinux.org>
|
|
The reality is that you do not need the abiltity to configure the
clock divider for ColdFire CPUs. It is a fixed ratio on any given
ColdFire family member. It is not the same for all ColdFire parts,
but it is always the same in a model range. So hard define the divider
for each supported ColdFire CPU type and remove the Kconfig option.
Signed-off-by: Greg Ungerer <gerg@uclinux.org>
|
|
Fix these compiler warnings:
arch/m68knommu/platform/5407/gpio.c:35:3: warning: initialisation makes pointer from integer without a cast
arch/m68knommu/platform/5407/gpio.c:36:3: warning: initialisation makes pointer from integer without a cast
arch/m68knommu/platform/5407/gpio.c:37:3: warning: initialisation makes pointer from integer without a cast
Signed-off-by: Greg Ungerer <gerg@uclinux.org>
|
|
Fix these compiler warnings:
arch/m68knommu/platform/532x/gpio.c:35:3: warning: initialisation makes pointer from integer without a cast
arch/m68knommu/platform/532x/gpio.c:36:3: warning: initialisation makes pointer from integer without a cast
arch/m68knommu/platform/532x/gpio.c:37:3: warning: initialisation makes pointer from integer without a cast
arch/m68knommu/platform/532x/gpio.c:51:3: warning: initialisation makes pointer from integer without a cast
arch/m68knommu/platform/532x/gpio.c:52:3: warning: initialisation makes pointer from integer without a cast
arch/m68knommu/platform/532x/gpio.c:53:3: warning: initialisation makes pointer from integer without a cast
arch/m68knommu/platform/532x/gpio.c:54:3: warning: initialisation makes pointer from integer without a cast
...
Signed-off-by: Greg Ungerer <gerg@uclinux.org>
|
|
Fix these compiler warnings:
arch/m68knommu/platform/5307/gpio.c:35:3: warning: initialisation makes pointer from integer without a cast
arch/m68knommu/platform/5307/gpio.c:36:3: warning: initialisation makes pointer from integer without a cast
arch/m68knommu/platform/5307/gpio.c:37:3: warning: initialisation makes pointer from integer without a cast
Signed-off-by: Greg Ungerer <gerg@uclinux.org>
|
|
Fix these compiler warnings:
arch/m68knommu/platform/527x/gpio.c:37:3: warning: initialisation makes pointer from integer without a cast
arch/m68knommu/platform/527x/gpio.c:38:3: warning: initialisation makes pointer from integer without a cast
arch/m68knommu/platform/527x/gpio.c:39:3: warning: initialisation makes pointer from integer without a cast
arch/m68knommu/platform/527x/gpio.c:53:3: warning: initialisation makes pointer from integer without a cast
arch/m68knommu/platform/527x/gpio.c:54:3: warning: initialisation makes pointer from integer without a cast
arch/m68knommu/platform/527x/gpio.c:55:3: warning: initialisation makes pointer from integer without a cast
...
Signed-off-by: Greg Ungerer <gerg@uclinux.org>
|
|
Fix these compiler warnings:
arch/m68knommu/platform/5272/gpio.c:35:3: warning: initialisation makes pointer from integer without a cast
arch/m68knommu/platform/5272/gpio.c:36:3: warning: initialisation makes pointer from integer without a cast
arch/m68knommu/platform/5272/gpio.c:37:3: warning: initialisation makes pointer from integer without a cast
arch/m68knommu/platform/5272/gpio.c:51:3: warning: initialisation makes pointer from integer without a cast
arch/m68knommu/platform/5272/gpio.c:52:3: warning: initialisation makes pointer from integer without a cast
arch/m68knommu/platform/5272/gpio.c:53:3: warning: initialisation makes pointer from integer without a cast
arch/m68knommu/platform/5272/gpio.c:67:3: warning: initialisation makes pointer from integer without a cast
arch/m68knommu/platform/5272/gpio.c:68:3: warning: initialisation makes pointer from integer without a cast
arch/m68knommu/platform/5272/gpio.c:69:3: warning: initialisation makes pointer from integer without a cast
Signed-off-by: Greg Ungerer <gerg@uclinux.org>
|
|
Fix these compiler warnings:
arch/m68knommu/platform/5249/gpio.c:35:3: warning: initialisation makes pointer from integer without a cast
arch/m68knommu/platform/5249/gpio.c:36:3: warning: initialisation makes pointer from integer without a cast
arch/m68knommu/platform/5249/gpio.c:37:3: warning: initialisation makes pointer from integer without a cast
arch/m68knommu/platform/5249/gpio.c:51:3: warning: initialisation makes pointer from integer without a cast
arch/m68knommu/platform/5249/gpio.c:52:3: warning: initialisation makes pointer from integer without a cast
arch/m68knommu/platform/5249/gpio.c:53:3: warning: initialisation makes pointer from integer without a cast
Signed-off-by: Greg Ungerer <gerg@uclinux.org>
|
|
Fix these compiler warnings:
arch/m68knommu/platform/523x/gpio.c:36:3: warning: initialisation makes pointer from integer without a cast
arch/m68knommu/platform/523x/gpio.c:37:3: warning: initialisation makes pointer from integer without a cast
arch/m68knommu/platform/523x/gpio.c:38:3: warning: initialisation makes pointer from integer without a cast
arch/m68knommu/platform/523x/gpio.c:52:3: warning: initialisation makes pointer from integer without a cast
arch/m68knommu/platform/523x/gpio.c:53:3: warning: initialisation makes pointer from integer without a cast
...
Signed-off-by: Greg Ungerer <gerg@uclinux.org>
|
|
Fix these compiler warnings:
rch/m68knommu/platform/520x/gpio.c:35:3: warning: initialisation makes pointer from integer without a cast
arch/m68knommu/platform/520x/gpio.c:36:3: warning: initialisation makes pointer from integer without a cast
arch/m68knommu/platform/520x/gpio.c:37:3: warning: initialisation makes pointer from integer without a cast
arch/m68knommu/platform/520x/gpio.c:51:3: warning: initialisation makes pointer from integer without a cast
arch/m68knommu/platform/520x/gpio.c:52:3: warning: initialisation makes pointer from integer without a cast
...
Signed-off-by: Greg Ungerer <gerg@uclinux.org>
|
|
Fix these compiler warnings:
arch/m68knommu/platform/5206e/gpio.c:35:3: warning: initialisation makes pointer from integer without a cast CC kernel/panic.o
arch/m68knommu/platform/5206e/gpio.c:36:3: warning: initialisation makes pointer from integer without a cast
arch/m68knommu/platform/5206e/gpio.c:37:3: warning: initialisation makes pointer from integer without a cast
Signed-off-by: Greg Ungerer <gerg@uclinux.org>
|
|
Fix these compiler warnings:
arch/m68knommu/platform/5206/gpio.c:35:3: warning: initialisation makes pointer from integer without a cast
arch/m68knommu/platform/5206/gpio.c:36:3: warning: initialisation makes pointer from integer without a cast
arch/m68knommu/platform/5206/gpio.c:37:3: warning: initialisation makes pointer from integer without a cast
Signed-off-by: Greg Ungerer <gerg@uclinux.org>
|
|
Signed-off-by: Alexander Kurz <linux@kbdbabel.org>
Signed-off-by: Greg Ungerer <gerg@uclinux.org>
|
|
The intc-simr interrupt controller on some ColdFire CPUs has a set range of
interrupts its supports (64 through 128 or 192 depending on model). We
shouldn't be setting this handler for every possible interrupt from 0 to
255. Set more appropriate limits, and this means we can drop the interrupt
number check in the mask and unmask routines.
Signed-off-by: Greg Ungerer <gerg@uclinux.org>
|
|
Use a proper irq_startup() routine to intialize the interrupt priority
and level register in the ColdFire intc-2 controller code. We shouldn't
be checking if the priority/level has been set on every unmask operation.
Signed-off-by: Greg Ungerer <gerg@uclinux.org>
|
|
The intc-2 interrupt controller on some ColdFire CPUs has a set range of
interrupts its supports (64 through 128 or 192 depending on model). We
shouldn't be setting this handler for every possible interrupt from 0 to
255. Set more appropriate limits, and this means we can drop the interrupt
number check in the mask and unmask routines.
Signed-off-by: Greg Ungerer <gerg@uclinux.org>
|
|
The FireBee is a ColdFire 5475 based board. Add a configuration option
to support it, and the basic platform flash layout code.
Signed-off-by: Greg Ungerer <gerg@uclinux.org>
|
|
Most ColdFire CPUs have an internal peripheral set that can be mapped at
a user selectable address. Different ColdFire parts either use an MBAR
register of an IPSBAR register to map the peripheral region. Most boards
use the Freescale default mappings - but not all.
Make the setting of the MBAR or IPSBAR register configurable. And only make
the selection available on the appropriate ColdFire CPU types.
Signed-off-by: Greg Ungerer <gerg@uclinux.org>
|
|
Different ColdFire CPUs have different ways of defining where their
internal peripheral registers sit in their address space. Some use an
MBAR register, some use and IPSBAR register, some have a fixed mapping.
Now that most of the peripheral address definitions have been cleaned up
we can clean up the setting of the MBAR and IPSBAR defines to limit them
to just where they are needed (and where they actually exist).
Signed-off-by: Greg Ungerer <gerg@uclinux.org>
|
|
In some of the RAM size autodetection code on ColdFire CPU startup
we reference DRAM registers relative to the MBAR register. Not all of
the supported ColdFire CPUs have an MBAR, and currently this works
because we fake an MBAR address on those registers. In an effort to
clean this up, and eventually remove the fake MBAR setting make the
DRAM register address definitions actually contain the MBAR (or IPSBAR
as appropriate) value as required.
Signed-off-by: Greg Ungerer <gerg@uclinux.org>
|
|
Not all ColdFire CPUs that use the old style timer hardware module use
an MBAR set peripheral region. Move the TIMER base address defines to the
per-CPU header files where we can set it correctly based on how the
peripherals are mapped - instead of using a fake MBAR for some platforms.
Signed-off-by: Greg Ungerer <gerg@uclinux.org>
|
|
The base addresses of the ColdFire DMA unit registers belong with
all the other address definitions in the per-cpu headers. The current
definitions assume they are relative to an MBAR register. Not all
ColdFire CPUs have an MBAR register. A clean address define can only
be acheived in the per-cpu headers along with all the other chips
peripheral base addresses.
Signed-off-by: Greg Ungerer <gerg@uclinux.org>
|
|
The ColdFire 528x family of CPUs does not have an MBAR register, so don't
define its peripheral addresses relative to one. Its internal peripherals
are relative to the IPSBAR register, so make sure to use that.
Signed-off-by: Greg Ungerer <gerg@uclinux.org>
|
|
The ColdFire 527x family of CPUs does not have an MBAR register, so don't
define its peripheral addresses relative to one. Its internal peripherals
are relative to the IPSBAR register, so make sure to use that.
Signed-off-by: Greg Ungerer <gerg@uclinux.org>
|
|
The ColdFire 523x family of CPUs does not have an MBAR register, so don't
define its peripheral addresses relative to one. Its internal peripherals
are relative to the IPSBAR register, so make sure to use that.
Signed-off-by: Greg Ungerer <gerg@uclinux.org>
|
|
The ColdFire 5207 and 5208 CPUs have fixed peripheral addresses.
They do not use the setable peripheral address registers like the MBAR
and IPSBAR used on many other ColdFire parts. Don't use fake values
of MBAR and IPSBAR when using peripheral addresses for them, there
is no need to.
Signed-off-by: Greg Ungerer <gerg@uclinux.org>
|
|
The PIT hardware timer module used in some ColdFire CPU's is not always
addressed relative to an IPSBAR register. Parts like the ColdFire 5207 and
5208 have fixed peripheral addresses. So lets not define the register
addresses of the PIT relative to an IPSBAR definition. Move the base
address definitions into the per-part headers. This is a lot more consistent
since all the other peripheral base addresses are defined in the per-part
header files already.
Signed-off-by: Greg Ungerer <gerg@uclinux.org>
|
|
Remove the bogus definition of the MBAR register for the ColdFire 532x
family. It doesn't have an MBAR register, its peripheral registers are
at fixed addresses and are not relative to a settable base.
All the code that relyed on this definition existing has been cleaned
up. The register address definitions now include the base as required.
Signed-off-by: Greg Ungerer <gerg@uclinux.org>
|
|
The ColdFire 54xx family shares the same interrupt controller used
on the 523x, 527x and 528x ColdFire parts, but it isn't offset
relative to the IPSBAR register. The 54xx doesn't have an IPSBAR
register.
By including the base address of the peripheral registers in the register
definitions (MCFICM_INTC0 and MCFICM_INTC1 in this case) we can avoid
having to define a fake IPSBAR for the 54xx. And this makes the register
address definitions of these more consistent, the majority of the other
register address defines include the peripheral base address already.
Signed-off-by: Greg Ungerer <gerg@uclinux.org>
|
|
The MBAR2 register is only used on the ColdFire 5249 part, so move its
definition out of the common coldfire.h and into the 5249 support header.
Signed-off-by: Greg Ungerer <gerg@uclinux.org>
|
|
All chips converted and proper accessor functions used.
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Signed-off-by: Greg Ungerer <gerg@uclinux.org>
|
|
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Signed-off-by: Greg Ungerer <gerg@uclinux.org>
|
|
/me idly wonders what sets the handlers for this chip.
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Signed-off-by: Greg Ungerer <gerg@uclinux.org>
|
|
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Signed-off-by: Greg Ungerer <gerg@uclinux.org>
|
|
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Signed-off-by: Greg Ungerer <gerg@uclinux.org>
|
|
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Signed-off-by: Greg Ungerer <gerg@uclinux.org>
|
|
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Signed-off-by: Greg Ungerer <gerg@uclinux.org>
|
|
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Signed-off-by: Greg Ungerer <gerg@uclinux.org>
|
|
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Signed-off-by: Greg Ungerer <gerg@uclinux.org>
|
|
That handler lacks the minimal checks for action being zero etc. Keep
the weird flow - ack before handling - intact and call into
handle_simple_irq which does the right thing.
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Acked-by: Greg Ungerer <gerg@uclinux.org>
LKML-Reference: <20110202212552.413849952@linutronix.de>
Signed-off-by: Greg Ungerer <gerg@uclinux.org>
|
|
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/dhowells/linux-2.6-mn10300
* 'fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/dhowells/linux-2.6-mn10300:
MN10300: atomic_read() should ensure it emits a load
MN10300: The SMP_ICACHE_INV_FLUSH_RANGE IPI command does not exist
MN10300: Proper use of macros get_user() in the case of incremented pointers
|
|
* 'upstream' of git://git.linux-mips.org/pub/scm/upstream-linus: (26 commits)
MIPS: Alchemy: Fix reset for MTX-1 and XXS1500
MIPS: MTX-1: Make au1000_eth probe all PHY addresses
MIPS: Jz4740: Add HAVE_CLK
MIPS: Move idle task creation to work queue
MIPS, Perf-events: Use unsigned delta for right shift in event update
MIPS, Perf-events: Work with the new callchain interface
MIPS, Perf-events: Fix event check in validate_event()
MIPS, Perf-events: Work with the new PMU interface
MIPS, Perf-events: Work with irq_work
MIPS: Fix always CONFIG_LOONGSON_UART_BASE=y
MIPS: Loongson: Fix potentially wrong string handling
MIPS: Fix GCC-4.6 'set but not used' warning in arch/mips/mm/init.c
MIPS: Fix GCC-4.6 'set but not used' warning in ieee754int.h
MIPS: Remove unused code from arch/mips/kernel/syscall.c
MIPS: Fix GCC-4.6 'set but not used' warning in signal*.c
MIPS: MSP: Fix MSP71xx bpci interrupt handler return value
MIPS: Select R4K timer lib for all MSP platforms
MIPS: Loongson: Remove ad-hoc cmdline default
MIPS: Clear the correct flag in sysmips(MIPS_FIXADE, ...).
MIPS: Add an unreachable return statement to satisfy buggy GCCs.
...
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/tip/linux-2.6-tip
* 'x86-fixes-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/linux-2.6-tip:
x86: ce4100: Set pci ops via callback instead of module init
x86/mm: Fix pgd_lock deadlock
x86/mm: Handle mm_fault_error() in kernel space
x86: Don't check for BIOS corruption in first 64K when there's no need to
|
|
This reverts the parent commit. I hate doing that, but it's generating
some discussion ("half of it is right"), and since I am planning on
doing the 2.6.38 release later today we can punt it to stable if
required. Let's not rock the boat right now.
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
|
|
oom_kill_process() starts with victim_points == 0. This means that
(most likely) any child has more points and can be killed erroneously.
Also, "children has a different mm" doesn't match the reality, we should
check child->mm != t->mm. This check is not exactly correct if t->mm ==
NULL but this doesn't really matter, oom_kill_task() will kill them
anyway.
Note: "Kill all processes sharing p->mm" in oom_kill_task() is wrong
too.
Signed-off-by: Oleg Nesterov <oleg@redhat.com>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
|
|
Since commit 32fd6901 (MIPS: Alchemy: get rid of common/reset.c)
Alchemy-based boards use their own reset function. For MTX-1 and XXS1500,
the reset function pokes at the BCSR.SYSTEM_RESET register, but this does
not work. According to Bruno Randolf, this was not tested when written.
Previously, the generic au1000_restart() routine called the board specific
reset function, which for MTX-1 and XXS1500 did not work, but finally made
a jump to the reset vector, which really triggers a system restart. Fix
reboot for both targets by jumping to the reset vector.
Signed-off-by: Florian Fainelli <florian@openwrt.org>
To: linux-mips@linux-mips.org
Patchwork: https://patchwork.linux-mips.org/patch/2093/
Acked-by: Bruno Randolf <br1@einfach.org>
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
|
|
When au1000_eth probes the MII bus for PHY address, if we do not set
au1000_eth platform data's phy_search_highest_address, the MII probing
logic will exit early and will assume a valid PHY is found at address 0.
For MTX-1, the PHY is at address 31, and without this patch, the link
detection/speed/duplex would not work correctly.
CC: stable@kernel.org
Signed-off-by: Florian Fainelli <florian@openwrt.org>
To: linux-mips@linux-mips.org
Patchwork: https://patchwork.linux-mips.org/patch/2111/
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
|
|
Jz4740 supports the clock framework but doesn't have HAVE_CLK defined,
so define it!
Signed-off-by: Maurus Cuelenaere <mcuelenaere@gmail.com>
To: linux-mips@linux-mips.org
To: linux-kernel@vger.kernel.org
Patchwork: https://patchwork.linux-mips.org/patch/2112/
Acked-by: Lars-Peter Clausen <lars@metafoo.de>
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
|
|
To avoid forking usermode thread when creating an idle task, move fork_idle
to a work queue.
If kernel starts with maxcpus= option which does not bring all available
cpus online at boot time, idle tasks for offline cpus are not created. If
later offline cpus are hotplugged through sysfs, __cpu_up is called in
the context of the user task, and fork_idle copies its non-zero mm
pointer. This causes BUG() in per_cpu_trap_init.
This also avoids issues with resource limits of the CPU writing to sysfs,
containers, maybe others.
Signed-off-by: Maksim Rayskiy <mrayskiy@broadcom.com>
To: linux-mips@linux-mips.org
Patchwork: https://patchwork.linux-mips.org/patch/2070/
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
|
