| Age | Commit message (Collapse) | Author |
|---|
|
When the guest cedes the vcpu or the vcpu has no guest to
run it naps. Clear the runlatch bit of the vcpu before
napping to indicate an idle cpu.
Signed-off-by: Preeti U Murthy <preeti@linux.vnet.ibm.com>
Acked-by: Paul Mackerras <paulus@samba.org>
Reviewed-by: Srivatsa S. Bhat <srivatsa.bhat@linux.vnet.ibm.com>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
|
|
The secondary threads in the core are kept offline before launching guests
in kvm on powerpc: "371fefd6f2dc4666:KVM: PPC: Allow book3s_hv guests to use
SMT processor modes."
Hence their runlatch bits are cleared. When the secondary threads are called
in to start a guest, their runlatch bits need to be set to indicate that they
are busy. The primary thread has its runlatch bit set though, but there is no
harm in setting this bit once again. Hence set the runlatch bit for all
threads before they start guest.
Signed-off-by: Preeti U Murthy <preeti@linux.vnet.ibm.com>
Acked-by: Paul Mackerras <paulus@samba.org>
Reviewed-by: Srivatsa S. Bhat <srivatsa.bhat@linux.vnet.ibm.com>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
|
|
Up until now we have been setting the runlatch bits for a busy CPU and
clearing it when a CPU enters idle state. The runlatch bit has thus
been consistent with the utilization of a CPU as long as the CPU is online.
However when a CPU is hotplugged out the runlatch bit is not cleared. It
needs to be cleared to indicate an unused CPU. Hence this patch has the
runlatch bit cleared for an offline CPU just before entering an idle state
and sets it immediately after it exits the idle state.
Signed-off-by: Preeti U Murthy <preeti@linux.vnet.ibm.com>
Acked-by: Paul Mackerras <paulus@samba.org>
Reviewed-by: Srivatsa S. Bhat <srivatsa.bhat@linux.vnet.ibm.com>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
|
|
While testing memory hot-remove, I found following dead lock:
Process #1141 is drmgr, trying to remove some memory, i.e. memory499.
It holds the memory_hotplug_mutex, and blocks when trying to remove file
"online" under dir memory499, in kernfs_drain(), at
wait_event(root->deactivate_waitq,
atomic_read(&kn->active) == KN_DEACTIVATED_BIAS);
Process #1120 is trying to online memory499 by
echo 1 > memory499/online
In .kernfs_fop_write, it uses kernfs_get_active() to increase
&kn->active, thus blocking process #1141. While itself is blocked later
when trying to acquire memory_hotplug_mutex, which is held by process
The backtrace of both processes are shown below:
[<c000000001b18600>] 0xc000000001b18600
[<c000000000015044>] .__switch_to+0x144/0x200
[<c000000000263ca4>] .online_pages+0x74/0x7b0
[<c00000000055b40c>] .memory_subsys_online+0x9c/0x150
[<c00000000053cbe8>] .device_online+0xb8/0x120
[<c00000000053cd04>] .online_store+0xb4/0xc0
[<c000000000538ce4>] .dev_attr_store+0x64/0xa0
[<c00000000030f4ec>] .sysfs_kf_write+0x7c/0xb0
[<c00000000030e574>] .kernfs_fop_write+0x154/0x1e0
[<c000000000268450>] .vfs_write+0xe0/0x260
[<c000000000269144>] .SyS_write+0x64/0x110
[<c000000000009ffc>] syscall_exit+0x0/0x7c
[<c000000001b18600>] 0xc000000001b18600
[<c000000000015044>] .__switch_to+0x144/0x200
[<c00000000030be14>] .__kernfs_remove+0x204/0x300
[<c00000000030d428>] .kernfs_remove_by_name_ns+0x68/0xf0
[<c00000000030fb38>] .sysfs_remove_file_ns+0x38/0x60
[<c000000000539354>] .device_remove_attrs+0x54/0xc0
[<c000000000539fd8>] .device_del+0x158/0x250
[<c00000000053a104>] .device_unregister+0x34/0xa0
[<c00000000055bc14>] .unregister_memory_section+0x164/0x170
[<c00000000024ee18>] .__remove_pages+0x108/0x4c0
[<c00000000004b590>] .arch_remove_memory+0x60/0xc0
[<c00000000026446c>] .remove_memory+0x8c/0xe0
[<c00000000007f9f4>] .pseries_remove_memblock+0xd4/0x160
[<c00000000007fcfc>] .pseries_memory_notifier+0x27c/0x290
[<c0000000008ae6cc>] .notifier_call_chain+0x8c/0x100
[<c0000000000d858c>] .__blocking_notifier_call_chain+0x6c/0xe0
[<c00000000071ddec>] .of_property_notify+0x7c/0xc0
[<c00000000071ed3c>] .of_update_property+0x3c/0x1b0
[<c0000000000756cc>] .ofdt_write+0x3dc/0x740
[<c0000000002f60fc>] .proc_reg_write+0xac/0x110
[<c000000000268450>] .vfs_write+0xe0/0x260
[<c000000000269144>] .SyS_write+0x64/0x110
[<c000000000009ffc>] syscall_exit+0x0/0x7c
This patch uses lock_device_hotplug() to protect remove_memory() called
in pseries_remove_memblock(), which is also stated before function
remove_memory():
* NOTE: The caller must call lock_device_hotplug() to serialize hotplug
* and online/offline operations before this call, as required by
* try_offline_node().
*/
void __ref remove_memory(int nid, u64 start, u64 size)
With this lock held, the other process(#1120 above) trying to online the
memory block will retry the system call when calling
lock_device_hotplug_sysfs(), and finally find No such device error.
Signed-off-by: Li Zhong <zhong@linux.vnet.ibm.com>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
|
|
module_init should return 0 or a negative errno.
Signed-off-by: Anton Blanchard <anton@samba.org>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
|
|
Bump the boot wrapper BOOT_COMMAND_LINE_SIZE to match the
kernel.
Signed-off-by: Anton Blanchard <anton@samba.org>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
|
|
I've had a report that the current limit is too small for
an automated network based installer. Bump it.
Signed-off-by: Anton Blanchard <anton@samba.org>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
|
|
We have two definitions of COMMAND_LINE_SIZE, one for the kernel
and one for the boot wrapper. I assume this is so the boot
wrapper can be self sufficient and not rely on kernel headers.
Having two defines with the same name is confusing, I just
updated the wrong one when trying to bump it.
Make the boot wrapper define unique by calling it
BOOT_COMMAND_LINE_SIZE.
Signed-off-by: Anton Blanchard <anton@samba.org>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
|
|
The catalog version number was changed from a be32 (with proceeding
32bits of padding) to a be64, update the code to treat it as a be64
Signed-off-by: Cody P Schafer <cody@linux.vnet.ibm.com>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
|
|
Signed-off-by: Cody P Schafer <cody@linux.vnet.ibm.com>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
|
|
plpar_hcall_norets()
Signed-off-by: Cody P Schafer <cody@linux.vnet.ibm.com>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
|
|
Signed-off-by: Cody P Schafer <cody@linux.vnet.ibm.com>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
|
|
fixup for "powerpc/perf: Add support for the hv gpci (get performance
counter info) interface".
Makes the "not enabled" message less awful (and hidden unless
debugging).
Signed-off-by: Cody P Schafer <cody@linux.vnet.ibm.com>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
|
|
fixup for "powerpc/perf: Add support for the hv 24x7 interface"
Makes the "not enabled" message less awful (and hides it in most cases).
Signed-off-by: Cody P Schafer <cody@linux.vnet.ibm.com>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
|
|
The if condition check was based on a draft ISA doc. Remove the same.
Signed-off-by: Aneesh Kumar K.V <aneesh.kumar@linux.vnet.ibm.com>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
|
|
Signed-off-by: Anton Blanchard <anton@samba.org>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
|
|
We have two copies of code that creates an OPAL sg list. Consolidate
these into a common set of helpers and fix the endian issues.
The flash interface embedded a version number in the num_entries
field, whereas the dump interface did did not. Since versioning
wasn't added to the flash interface and it is impossible to add
this in a backwards compatible way, just remove it.
Signed-off-by: Anton Blanchard <anton@samba.org>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
|
|
Fix little endian issues with the OPAL error log code.
Signed-off-by: Anton Blanchard <anton@samba.org>
Reviewed-by: Stewart Smith <stewart@linux.vnet.ibm.com>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
|
|
The bitmap in opal_poll_events and opal_handle_interrupt is
big endian, so we need to byteswap it on little endian builds.
Signed-off-by: Anton Blanchard <anton@samba.org>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
|
|
We had some duplication of the internal OPAL functions.
Signed-off-by: Anton Blanchard <anton@samba.org>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
|
|
Using size_t in our APIs is asking for trouble, especially
when some OPAL calls use size_t pointers.
Signed-off-by: Anton Blanchard <anton@samba.org>
Reviewed-by: Stewart Smith <stewart@linux.vnet.ibm.com>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
|
|
On PowerNV platform, we are holding an unnecessary refcount on a pci_dev, which
leads to the pci_dev is not destroyed when hotplugging a pci device.
This patch release the unnecessary refcount.
Signed-off-by: Wei Yang <weiyang@linux.vnet.ibm.com>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
|
|
During the EEH hotplug event, iommu_add_device() will be invoked three times
and two of them will trigger warning or error.
The three times to invoke the iommu_add_device() are:
pci_device_add
...
set_iommu_table_base_and_group <- 1st time, fail
device_add
...
tce_iommu_bus_notifier <- 2nd time, succees
pcibios_add_pci_devices
...
pcibios_setup_bus_devices <- 3rd time, re-attach
The first time fails, since the dev->kobj->sd is not initialized. The
dev->kobj->sd is initialized in device_add().
The third time's warning is triggered by the re-attach of the iommu_group.
After applying this patch, the error
iommu_tce: 0003:05:00.0 has not been added, ret=-14
and the warning
[ 204.123609] ------------[ cut here ]------------
[ 204.123645] WARNING: at arch/powerpc/kernel/iommu.c:1125
[ 204.123680] Modules linked in: xt_CHECKSUM nf_conntrack_netbios_ns nf_conntrack_broadcast ipt_MASQUERADE ip6t_REJECT bnep bluetooth 6lowpan_iphc rfkill xt_conntrack ebtable_nat ebtable_broute bridge stp llc mlx4_ib ib_sa ib_mad ib_core ib_addr ebtable_filter ebtables ip6table_nat nf_conntrack_ipv6 nf_defrag_ipv6 nf_nat_ipv6 ip6table_mangle ip6table_security ip6table_raw ip6table_filter ip6_tables iptable_nat nf_conntrack_ipv4 nf_defrag_ipv4 nf_nat_ipv4 nf_nat nf_conntrack iptable_mangle iptable_security iptable_raw bnx2x tg3 mlx4_core nfsd ptp mdio ses libcrc32c nfs_acl enclosure be2net pps_core shpchp lockd kvm uinput sunrpc binfmt_misc lpfc scsi_transport_fc ipr scsi_tgt
[ 204.124356] CPU: 18 PID: 650 Comm: eehd Not tainted 3.14.0-rc5yw+ #102
[ 204.124400] task: c0000027ed485670 ti: c0000027ed50c000 task.ti: c0000027ed50c000
[ 204.124453] NIP: c00000000003cf80 LR: c00000000006c648 CTR: c00000000006c5c0
[ 204.124506] REGS: c0000027ed50f440 TRAP: 0700 Not tainted (3.14.0-rc5yw+)
[ 204.124558] MSR: 9000000000029032 <SF,HV,EE,ME,IR,DR,RI> CR: 88008084 XER: 20000000
[ 204.124682] CFAR: c00000000006c644 SOFTE: 1
GPR00: c00000000006c648 c0000027ed50f6c0 c000000001398380 c0000027ec260300
GPR04: c0000027ea92c000 c00000000006ad00 c0000000016e41b0 0000000000000110
GPR08: c0000000012cd4c0 0000000000000001 c0000027ec2602ff 0000000000000062
GPR12: 0000000028008084 c00000000fdca200 c0000000000d1d90 c0000027ec281a80
GPR16: 0000000000000000 0000000000000000 0000000000000000 0000000000000000
GPR20: 0000000000000000 0000000000000000 0000000000000000 0000000000000001
GPR24: 000000005342697b 0000000000002906 c000001fe6ac9800 c000001fe6ac9800
GPR28: 0000000000000000 c0000000016e3a80 c0000027ea92c090 c0000027ea92c000
[ 204.125353] NIP [c00000000003cf80] .iommu_add_device+0x30/0x1f0
[ 204.125399] LR [c00000000006c648] .pnv_pci_ioda_dma_dev_setup+0x88/0xb0
[ 204.125443] Call Trace:
[ 204.125464] [c0000027ed50f6c0] [c0000027ed50f750] 0xc0000027ed50f750 (unreliable)
[ 204.125526] [c0000027ed50f750] [c00000000006c648] .pnv_pci_ioda_dma_dev_setup+0x88/0xb0
[ 204.125588] [c0000027ed50f7d0] [c000000000069cc8] .pnv_pci_dma_dev_setup+0x78/0x340
[ 204.125650] [c0000027ed50f870] [c000000000044408] .pcibios_setup_device+0x88/0x2f0
[ 204.125712] [c0000027ed50f940] [c000000000046040] .pcibios_setup_bus_devices+0x60/0xd0
[ 204.125774] [c0000027ed50f9c0] [c000000000043acc] .pcibios_add_pci_devices+0xdc/0x1c0
[ 204.125837] [c0000027ed50fa50] [c00000000086f970] .eeh_reset_device+0x36c/0x4f0
[ 204.125939] [c0000027ed50fb20] [c00000000003a2d8] .eeh_handle_normal_event+0x448/0x480
[ 204.126068] [c0000027ed50fbc0] [c00000000003a35c] .eeh_handle_event+0x4c/0x340
[ 204.126192] [c0000027ed50fc80] [c00000000003a74c] .eeh_event_handler+0xfc/0x1b0
[ 204.126319] [c0000027ed50fd30] [c0000000000d1ea0] .kthread+0x110/0x130
[ 204.126430] [c0000027ed50fe30] [c00000000000a460] .ret_from_kernel_thread+0x5c/0x7c
[ 204.126556] Instruction dump:
[ 204.126610] 7c0802a6 fba1ffe8 fbc1fff0 fbe1fff8 f8010010 f821ff71 7c7e1b78 60000000
[ 204.126787] 60000000 e87e0298 3143ffff 7d2a1910 <0b090000> 2fa90000 40de00c8 ebfe0218
[ 204.126966] ---[ end trace 6e7aefd80add2973 ]---
are cleared.
This patch removes iommu_add_device() in pnv_pci_ioda_dma_dev_setup(), which
revert part of the change in commit d905c5df(PPC: POWERNV: move
iommu_add_device earlier).
Signed-off-by: Wei Yang <weiyang@linux.vnet.ibm.com>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
|
|
With this patch I was able to update firmware on an LE kernel.
Signed-off-by: Anton Blanchard <anton@samba.org>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
|
|
We have a subtle race when sending CPUs back to OPAL on kexec.
We mark them as "in real mode" right before we send them down. Once
we've booted the new kernel, it might try to call opal_reinit_cpus()
to change endianness, and that requires all CPUs to be spinning inside
OPAL.
However there is no synchronization here and we've observed cases
where the returning CPUs hadn't established their new state inside
OPAL before opal_reinit_cpus() is called, causing it to fail.
The proper fix is to actually wait for them to go down all the way
from the kexec'ing kernel.
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
|
|
The size of the sysparam sysfs files is determined from the device tree
at boot. However the buffer is hard coded to 64 bytes. If we encounter a
parameter that is larger than 64, or miss-parse the device tree, the
buffer will overflow when reading or writing to the parameter.
Check it at discovery time, and if the parameter is too large, do not
create a sysfs entry for it.
Signed-off-by: Joel Stanley <joel@jms.id.au>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
|
|
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
|
|
The sysparam code currently uses the userspace supplied number of
bytes when memcpy()ing in to a local 64-byte buffer.
Limit the maximum number of bytes by the size of the buffer.
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
|
|
The OPAL calls are returning int64_t values, which the sysparam code
stores in an int, and the sysfs callback returns ssize_t. Make code a
easier to read by consistently using ssize_t.
Signed-off-by: Joel Stanley <joel@jms.id.au>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
|
|
When a sysparam query in OPAL returned a negative value (error code),
sysfs would spew out a decent chunk of memory; almost 64K more than
expected. This was traced to a sign/unsigned mix up in the OPAL sysparam
sysfs code at sys_param_show.
The return value of sys_param_show is a ssize_t, calculated using
return ret ? ret : attr->param_size;
Alan Modra explains:
"attr->param_size" is an unsigned int, "ret" an int, so the overall
expression has type unsigned int. Result is that ret is cast to
unsigned int before being cast to ssize_t.
Instead of using the ternary operator, set ret to the param_size if an
error is not detected. The same bug exists in the sysfs write callback;
this patch fixes it in the same way.
A note on debugging this next time: on my system gcc will warn about
this if compiled with -Wsign-compare, which is not enabled by -Wall,
only -Wextra.
Signed-off-by: Joel Stanley <joel@jms.id.au>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
|
|
commit 41dd03a9 may cause Oops in rtas_stop_self().
The reason is that the rtas_args was moved into stack space. For a box
with more that 4GB RAM, the stack could easily be outside 32bit range,
but RTAS is 32bit.
So the patch moves rtas_args away from stack by adding static before
it.
Signed-off-by: Li Zhong <zhong@linux.vnet.ibm.com>
Signed-off-by: Anton Blanchard <anton@samba.org>
Cc: stable@vger.kernel.org # 3.14+
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
|
|
Commit aac416fc38c (lkdtm: flush icache and report actions) calls
flush_icache_range from a module. It's exported on most architectures
that implement it, but not on powerpc. This patch exports it to fix
the module link failure.
Signed-off-by: Jeff Mahoney <jeffm@suse.com>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
|
|
|
|
Pull slave-dmaengine fixes from Vinod Koul:
"Back from long weekend here in India and now the time to send fixes
for slave dmaengine.
- Dan's fix of sirf xlate code
- Jean's fix for timberland
- edma fixes by Sekhar for SG handling and Yuan for changing init
call"
* 'fixes' of git://git.infradead.org/users/vkoul/slave-dma:
dma: fix eDMA driver as a subsys_initcall
dmaengine: sirf: off by one in of_dma_sirfsoc_xlate()
platform: Fix timberdale dependencies
dma: edma: fix incorrect SG list handling
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/joro/iommu
Pull iommu fixes from Joerg Roedel:
"Fixes for regressions:
- fix wrong IOMMU enumeration causing some SCSI device drivers
initialization failures
- ARM-SMMU fixes for a panic condition and a wrong return value"
* tag 'iommu-fixes-v3.15-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/joro/iommu:
iommu/arm-smmu: fix panic in arm_smmu_alloc_init_pte
iommu/arm-smmu: Return 0 on unmap failure
iommu/vt-d: fix bug in matching PCI devices with DRHD/RMRR descriptors
iommu/vt-d: Fix get_domain_for_dev() handling of upstream PCIe bridges
iommu/vt-d: fix memory leakage caused by commit ea8ea46
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip
Pull perf tooling fixes from Ingo Molnar:
"Three small tooling fixes"
* 'perf-urgent-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
perf tools: Improve error reporting
perf tools: Adjust symbols in VDSO
perf kvm: Fix 'Min time' counting in report command
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/jolsa/perf into perf/urgent
Pull perf/urgent fixes from Jiri Olsa:
User visible changes:
* Adjust symbols in VDSO to properly resolve its function names (Vladimir Nikulichev)
* Improve error reporting for record session failure (Adrien BAK)
* Fix 'Min time' counting in report command (Alexander Yarygin)
Signed-off-by: Jiri Olsa <jolsa@redhat.com>
Signed-off-by: Ingo Molnar <mingo@kernel.org>
|
|
In the current version, when using perf record, if something goes
wrong in tools/perf/builtin-record.c:375
session = perf_session__new(file, false, NULL);
The error message:
"Not enough memory for reading per file header"
is issued. This error message seems to be outdated and is not very
helpful. This patch proposes to replace this error message by
"Perf session creation failed"
I believe this issue has been brought to lkml:
https://lkml.org/lkml/2014/2/24/458
although this patch only tackles a (small) part of the issue.
Additionnaly, this patch improves error reporting in
tools/perf/util/data.c open_file_write.
Currently, if the call to open fails, the user is unaware of it.
This patch logs the error, before returning the error code to
the caller.
Reported-by: Will Deacon <will.deacon@arm.com>
Signed-off-by: Adrien BAK <adrien.bak@metascale.org>
Link: http://lkml.kernel.org/r/1397786443.3093.4.camel@beast
[ Reorganize the changelog into paragraphs ]
[ Added empty line after fd declaration in open_file_write ]
Signed-off-by: Jiri Olsa <jolsa@redhat.com>
|
|
pert-report doesn't resolve function names in VDSO:
$ perf report --stdio -g flat,0.0,15,callee --sort pid
...
8.76%
0x7fff6b1fe861
__gettimeofday
ACE_OS::gettimeofday()
...
In this case symbol values should be adjusted the same way as for executables,
relocatable objects and prelinked libraries.
After fix:
$ perf report --stdio -g flat,0.0,15,callee --sort pid
...
8.76%
__vdso_gettimeofday
__gettimeofday
ACE_OS::gettimeofday()
Signed-off-by: Vladimir Nikulichev <nvs@tbricks.com>
Tested-by: Namhyung Kim <namhyung@kernel.org>
Reviewed-by: Adrian Hunter <adrian.hunter@intel.com>
Link: http://lkml.kernel.org/r/969812.163009436-sendEmail@nvs
Signed-off-by: Jiri Olsa <jolsa@redhat.com>
|
|
Every event in the perf-kvm has a 'stats' structure, which contains
max/min/average/etc times of handling this event.
The problem is that the 'perf-kvm stat report' command always shows
that 'min time' is 0us for every event. Example:
# perf kvm stat report
Analyze events for all VCPUs:
VM-EXIT Samples Samples% Time% Min Time Max Time Avg time
[..]
0xB2 MSCH 12 0.07% 0.00% 0us 8us 7.31us ( +- 2.11% )
0xB2 CHSC 12 0.07% 0.00% 0us 18us 9.39us ( +- 9.49% )
0xB2 STPX 8 0.05% 0.00% 0us 2us 1.88us ( +- 7.18% )
0xB2 STSI 7 0.04% 0.00% 0us 44us 16.49us ( +- 38.20% )
[..]
This happens because the 'stats' structure is not initialized and
stats->min equals to 0. Lets initialize the structure for every
event after its allocation using init_stats() function. This initializes
stats->min to -1 and makes 'Min time' statistics counting work:
# perf kvm stat report
Analyze events for all VCPUs:
VM-EXIT Samples Samples% Time% Min Time Max Time Avg time
[..]
0xB2 MSCH 12 0.07% 0.00% 6us 8us 7.31us ( +- 2.11% )
0xB2 CHSC 12 0.07% 0.00% 7us 18us 9.39us ( +- 9.49% )
0xB2 STPX 8 0.05% 0.00% 1us 2us 1.88us ( +- 7.18% )
0xB2 STSI 7 0.04% 0.00% 1us 44us 16.49us ( +- 38.20% )
[..]
Signed-off-by: Alexander Yarygin <yarygin@linux.vnet.ibm.com>
Signed-off-by: Christian Borntraeger <borntraeger@de.ibm.com>
Reviewed-by: David Ahern <dsahern@gmail.com>
Link: http://lkml.kernel.org/r/1397053319-2130-3-git-send-email-borntraeger@de.ibm.com
[ Fixing the perf examples changelog output ]
Signed-off-by: Jiri Olsa <jolsa@redhat.com>
|
|
A va_list needs to be copied in case it needs to be used twice.
Thanks to Hugh for debugging this issue, leading to various panics.
Tested:
lpq84:~# echo "|/foobar12345 %h %h %h %h %h %h %h %h %h %h %h %h %h %h %h %h %h %h %h %h" >/proc/sys/kernel/core_pattern
'produce_core' is simply : main() { *(int *)0 = 1;}
lpq84:~# ./produce_core
Segmentation fault (core dumped)
lpq84:~# dmesg | tail -1
[ 614.352947] Core dump to |/foobar12345 lpq84 lpq84 lpq84 lpq84 lpq84 lpq84 lpq84 lpq84 lpq84 lpq84 lpq84 lpq84 lpq84 lpq84 lpq84 lpq84 lpq84 lpq84 lpq84 (null) pipe failed
Notice the last argument was replaced by a NULL (we were lucky enough to
not crash, but do not try this on your production machine !)
After fix :
lpq83:~# echo "|/foobar12345 %h %h %h %h %h %h %h %h %h %h %h %h %h %h %h %h %h %h %h %h" >/proc/sys/kernel/core_pattern
lpq83:~# ./produce_core
Segmentation fault
lpq83:~# dmesg | tail -1
[ 740.800441] Core dump to |/foobar12345 lpq83 lpq83 lpq83 lpq83 lpq83 lpq83 lpq83 lpq83 lpq83 lpq83 lpq83 lpq83 lpq83 lpq83 lpq83 lpq83 lpq83 lpq83 lpq83 lpq83 pipe failed
Fixes: 5fe9d8ca21cc ("coredump: cn_vprintf() has no reason to call vsnprintf() twice")
Signed-off-by: Eric Dumazet <edumazet@google.com>
Diagnosed-by: Hugh Dickins <hughd@google.com>
Acked-by: Oleg Nesterov <oleg@redhat.com>
Cc: Neil Horman <nhorman@tuxdriver.com>
Cc: Andrew Morton <akpm@linux-foundation.org>
Cc: stable@vger.kernel.org # 3.11+
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip
Pull x86 fix from Ingo Molnar:
"This fixes the preemption-count imbalance crash reported by Owen
Kibel"
* 'x86-urgent-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
x86/mce: Fix CMCI preemption bugs
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip
Pull scheduler fixes from Ingo Molnar:
"Two fixes:
- a SCHED_DEADLINE task selection fix
- a sched/numa related lockdep splat fix"
* 'sched-urgent-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
sched: Check for stop task appearance when balancing happens
sched/numa: Fix task_numa_free() lockdep splat
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip
Pull perf fixes from Ingo Molnar:
"Two kernel side fixes:
- an Intel uncore PMU driver potential crash fix
- a kprobes/perf-call-graph interaction fix"
* 'perf-urgent-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
perf/x86/intel: Use rdmsrl_safe() when initializing RAPL PMU
kprobes/x86: Fix page-fault handling logic
|
|
Pull drm fixes from Dave Airlie:
"Unfortunately this contains no easter eggs, its a bit larger than I'd
like, but I included a patch that just moves code from one file to
another and I'd like to avoid merge conflicts with that later, so it
makes it seem worse than it is,
Otherwise:
- radeon: fixes to use new microcode to stabilise some cards, use
some common displayport code, some runtime pm fixes, pll regression
fixes
- i915: fix for some context oopses, a warn in a used path, backlight
fixes
- nouveau: regression fix
- omap: a bunch of fixes"
* 'drm-fixes' of git://people.freedesktop.org/~airlied/linux: (51 commits)
drm: bochs: drop unused struct fields
drm: bochs: add power management support
drm: cirrus: add power management support
drm: Split out drm_probe_helper.c from drm_crtc_helper.c
drm/plane-helper: Don't fake-implement primary plane disabling
drm/ast: fix value check in cbr_scan2
drm/nouveau/bios: fix a bit shift error introduced by 457e77b
drm/radeon/ci: make sure mc ucode is loaded before checking the size
drm/radeon/si: make sure mc ucode is loaded before checking the size
drm/radeon: improve PLL params if we don't match exactly v2
drm/radeon: memory leak on bo reservation failure. v2
drm/radeon: fix VCE fence command
drm/radeon: re-enable mclk dpm on R7 260X asics
drm/radeon: add support for newer mc ucode on CI (v2)
drm/radeon: add support for newer mc ucode on SI (v2)
drm/radeon: apply more strict limits for PLL params v2
drm/radeon: update CI DPM powertune settings
drm/radeon: fix runpm handling on APUs (v4)
drm/radeon: disable mclk dpm on R7 260X
drm/tegra: Remove gratuitous pad field
...
|
|
git://people.freedesktop.org/~deathsimple/linux into drm-next
Some i2c fixes over DisplayPort.
* 'drm-next-3.15-wip' of git://people.freedesktop.org/~deathsimple/linux:
drm/radeon: Improve vramlimit module param documentation
drm/radeon: fix audio pin counts for DCE6+ (v2)
drm/radeon/dp: switch to the common i2c over aux code
drm/dp/i2c: Update comments about common i2c over dp assumptions (v3)
drm/dp/i2c: send bare addresses to properly reset i2c connections (v4)
drm/radeon/dp: handle zero sized i2c over aux transactions (v2)
drm/i915: support address only i2c-over-aux transactions
drm/tegra: dp: Support address-only I2C-over-AUX transactions
|
|
Pull more networking fixes from David Miller:
1) Fix mlx4_en_netpoll implementation, it needs to schedule a NAPI
context, not synchronize it. From Chris Mason.
2) Ipv4 flow input interface should never be zero, it should be
LOOPBACK_IFINDEX instead. From Cong Wang and Julian Anastasov.
3) Properly configure MAC to PHY connection in mvneta devices, from
Thomas Petazzoni.
4) sys_recv should use SYSCALL_DEFINE. From Jan Glauber.
5) Tunnel driver ioctls do not use the correct namespace, fix from
Nicolas Dichtel.
6) Fix memory leak on seccomp filter attach, from Kees Cook.
7) Fix lockdep warning for nested vlans, from Ding Tianhong.
8) Crashes can happen in SCTP due to how the auth_enable value is
managed, fix from Vlad Yasevich.
9) Wireless fixes from John W Linville and co.
* git://git.kernel.org/pub/scm/linux/kernel/git/davem/net: (45 commits)
net: sctp: cache auth_enable per endpoint
tg3: update rx_jumbo_pending ring param only when jumbo frames are enabled
vlan: Fix lockdep warning when vlan dev handle notification
seccomp: fix memory leak on filter attach
isdn: icn: buffer overflow in icn_command()
ip6_tunnel: use the right netns in ioctl handler
sit: use the right netns in ioctl handler
ip_tunnel: use the right netns in ioctl handler
net: use SYSCALL_DEFINEx for sys_recv
net: mdio-gpio: Add support for separate MDI and MDO gpio pins
net: mdio-gpio: Add support for active low gpio pins
net: mdio-gpio: Use devm_ functions where possible
ipv4, route: pass 0 instead of LOOPBACK_IFINDEX to fib_validate_source()
ipv4, fib: pass LOOPBACK_IFINDEX instead of 0 to flowi4_iif
mlx4_en: don't use napi_synchronize inside mlx4_en_netpoll
net: mvneta: properly configure the MAC <-> PHY connection in all situations
net: phy: add minimal support for QSGMII PHY
sfc:On MCDI timeout, issue an FLR (and mark MCDI to fail-fast)
mwifiex: fix hung task on command timeout
mwifiex: process event before command response
...
|
|
Pull cifs fixes from Steve French:
"A set of 5 small cifs fixes"
* 'for-next' of git://git.samba.org/sfrench/cifs-2.6:
cif: fix dead code
cifs: fix error handling cifs_user_readv
fs: cifs: remove unused variable.
Return correct error on query of xattr on file with empty xattrs
cifs: Wait for writebacks to complete before attempting write.
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/char-misc
Pull char/misc driver fixes from Greg KH:
"Here are a few driver fixes for char/misc drivers that resolve
reported issues.
All have been in linux-next successfully for a few days"
* tag 'char-misc-3.15-rc2' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/char-misc:
Drivers: hv: vmbus: Negotiate version 3.0 when running on ws2012r2 hosts
Tools: hv: Handle the case when the target file exists correctly
vme_tsi148: Utilize to_pci_dev() macro
vme_tsi148: Fix PCI address mapping assumption
vme_tsi148: Fix typo in tsi148_slave_get()
w1: avoid recursive device_add
w1: fix netlink refcnt leak on error path
misc: Grammar s/addition/additional/
drivers: mcb: fix memory leak in chameleon_parse_cells() error path
mei: ignore client writing state during cb completion
mei: me: do not load the driver if the FW doesn't support MEI interface
GenWQE: Increase driver version number
GenWQE: Fix multithreading problems
GenWQE: Ensure rc is not returning an uninitialized value
GenWQE: Add wmb before DDCB is started
GenWQE: Enable access to VPD flash area
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/driver-core
Pull driver core fixes from Greg KH:
"Here are some driver core fixes for 3.15-rc2. Also in here are some
documentation updates, as well as an API removal that had to wait for
after -rc1 due to the cleanups coming into you from multiple developer
trees (this one and the PPC tree.)
All have been in linux next successfully"
* tag 'driver-core-3.15-rc2' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/driver-core:
drivers/base/dd.c incorrect pr_debug() parameters
Documentation: Update stable address in Chinese and Japanese translations
topology: Fix compilation warning when not in SMP
Chinese: add translation of io_ordering.txt
stable_kernel_rules: spelling/word usage
sysfs, driver-core: remove unused {sysfs|device}_schedule_callback_owner()
kernfs: protect lazy kernfs_iattrs allocation with mutex
fs: Don't return 0 from get_anon_bdev
|
