| Age | Commit message (Collapse) | Author |
|---|
|
This change makes it possible to limit the number of descriptors down to 48
per ring. The reason for this change is to address a variation on hardware
errata 10 for 82546GB in which descriptors will be lost if more than 32
descriptors are fetched and the PCI-X MRBC is 512.
Signed-off-by: Alexander Duyck <alexander.h.duyck@intel.com>
Tested-by: Emil Tantilov <emil.s.tantilov@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
drivers/net/82596.c: In function 'i596_open':
drivers/net/82596.c:1044: warning: label 'err_irq_dev' defined but not used
Caused by "82596: free resources on error"
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
As reported by Andrew:
drivers/net/ks8842.c: In function 'ks8842_handle_rx':
drivers/net/ks8842.c:428: warning: 'status' may be used uninitialized in this function
Just use the 32-bit status for all reads, and delete the useless
cast to 'int' when reading a u16 into 'len'.
Reported-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Use modern this_cpu_xxx() api, saving few bytes on x86
Signed-off-by: Eric Dumazet <eric.dumazet@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
On SMP systems, the SMSC911x registers may be accessed by multiple CPUs
and this seems to put the chip in an inconsistent state. The patch adds
spinlocks to the smsc911x_reg_read, smsc911x_reg_write,
smsc911x_rx_readfifo and smsc911x_tx_writefifo functions.
Signed-off-by: Catalin Marinas <catalin.marinas@arm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
drivers/net/bonding/bond_main.c:179:12: warning: ‘disable_netpoll’
defined but not used
Signed-off-by: Eric Dumazet <eric.dumazet@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
ARCH_PNX010X doesn't exist in Kconfig, therefore removing all
references for it from the source code/Kconfig.
Signed-off-by: Christoph Egger <siccegge@cs.fau.de>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Respect the interrupt type set in VM configuration.
When interrupt type is not auto, do not ignore the interrupt type set from
VM configuration.
Signed-off-by: Shreyas Bhatewara <sbhatewara@vmware.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Hold rtnl_lock to get the right link state.
While asynchronously resetting the device, hold rtnl_lock to get the
right value from netif_running. If a reset is scheduled, and the device
goes thru close and open, it may happen that reset and open may run in
parallel. Holding rtnl_lock will avoid this.
Signed-off-by: Shreyas Bhatewara <sbhatewara@vmware.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Since struct netdev_queue tx_bytes/tx_packets/tx_dropped are already
protected by _xmit_lock, its easy to convert these fields to u64 instead
of unsigned long.
This completes 64bit stats for devices using them (vlan, macvlan, ...)
Strictly, we could avoid the locking in dev_txq_stats_fold() on 64bit
arches, but its slow path and we prefer keep it simple.
Signed-off-by: Eric Dumazet <eric.dumazet@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
After commit ad1afb0039391 (vlan_dev: VLAN 0 should be treated
as "no vlan tag" (802.1p packet)),
bond_inet6addr_event() might be called with a NULL bond->vlgrp pointer, and
a non empty bond->vlan_list. vlan_group_get_device() is dereferencing a NULL pointer.
Signed-off-by: Eric Dumazet <eric.dumazet@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
The memory for the private data is allocated using kzalloc in
alloc_etherdev (or alloc_netdev_mq respectively) so there is no need to
set it to 0 again.
Signed-off-by: Tobias Klauser <tklauser@distanz.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
This patch adds a new networking option to allow hardware time stamps
from PHY devices. When enabled, likely candidates among incoming and
outgoing network packets are offered to the PHY driver for possible
time stamping. When accepted by the PHY driver, incoming packets are
deferred for later delivery by the driver.
The patch also adds phylib driver methods for the SIOCSHWTSTAMP ioctl
and callbacks for transmit and receive time stamping. Drivers may
optionally implement these functions.
Signed-off-by: Richard Cochran <richard.cochran@omicron.at>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Certain kinds of hardware time stamping units in both MACs and PHYs have
the limitation that they can only time stamp PTP packets. Drivers for such
hardware are left with the task of correctly matching skbs to time stamps.
This patch adds a BPF that drivers can use to classify PTP packets when
needed.
Signed-off-by: Richard Cochran <richard.cochran@omicron.at>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
The phy_mii_ioctl() function unnecessarily throws away the original ifreq.
We need access to the ifreq in order to support PHYs that can perform
hardware time stamping.
Two maverick drivers filter the ioctl commands passed to phy_mii_ioctl().
This is unnecessary since phylib will check the command in any case.
Signed-off-by: Richard Cochran <richard.cochran@omicron.at>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
This patch adds a hook for transmit time stamps. The transmit hook
allows a software fallback for transmit time stamps, for MACs
lacking time stamping hardware. Using the hook will still require
adding an inline function call to each MAC driver.
Signed-off-by: Richard Cochran <richard.cochran@omicron.at>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
- Without the 8021q module loaded in the kernel, all 802.1p packets
(VLAN 0 but QoS tagging) are silently discarded (as expected, as
the protocol is not loaded).
- Without this patch in 8021q module, these packets are forwarded to
the module, but they are discarded also if VLAN 0 is not configured,
which should not be the default behaviour, as VLAN 0 is not really
a VLANed packet but a 802.1p packet. Defining VLAN 0 makes it almost
impossible to communicate with mixed 802.1p and non 802.1p devices on
the same network due to arp table issues.
- Changed logic to skip vlan specific code in vlan_skb_recv if VLAN
is 0 and we have not defined a VLAN with ID 0, but we accept the
packet with the encapsulated proto and pass it later to netif_rx.
- In the vlan device event handler, added some logic to add VLAN 0
to HW filter in devices that support it (this prevented any traffic
in VLAN 0 to reach the stack in e1000e with HW filter under 2.6.35,
and probably also with other HW filtered cards, so we fix it here).
- In the vlan unregister logic, prevent the elimination of VLAN 0
in devices with HW filter.
- The default behaviour is to ignore the VLAN 0 tagging and accept
the packet as if it was not tagged, but we can still define a
VLAN 0 if desired (so it is backwards compatible).
Signed-off-by: Pedro Garcia <pedro.netdev@dondevamos.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
MAX_SOCK_ADDR is no longer used because commit 230b1839 "net: Use standard
structures for generic socket address structures." replaced
"char address[MAX_SOCK_ADDR];" with "struct sockaddr_storage address;".
Signed-off-by: Tetsuo Handa <penguin-kernel@I-love.SAKURA.ne.jp>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
probe_irq_off() returns the first irq found or if two irqs are found
then it returns the negative of the first irq found. We can cast
dev->irq to an int so that the test for negative values works.
Signed-off-by: Dan Carpenter <error27@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
'gap' is unsigned, so this code is wrong:
gap = -new_head;
...
if (gap > 0) { ... }
Make 'gap' signed.
The semantic patch that finds this problem (many false-positive results):
(http://coccinelle.lip6.fr/)
// <smpl>
@ r1 @
identifier f;
@@
int f(...) { ... }
@@
identifier r1.f;
type T;
unsigned T x;
@@
*x = f(...)
...
*x > 0
Signed-off-by: Kulikov Vasiliy <segooon@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
pci_get_domain_bus_and_slot: caller must decrement the
reference count by calling pci_dev_put().
Signed-off-by: Amit Kumar Salecha <amit.salecha@qlogic.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
This change initializes the state of link at the time when driver is
loaded. The ethtool output for 'link detected' and 'link speed'
is thus valid even before the interface is brought up.
Signed-off-by: Shreyas Bhatewara <sbhatewara@vmware.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Use DMA API as PCI equivalents will be deprecated. This change also allow
to allocate with GFP_KERNEL in some places.
Signed-off-by: Stanislaw Gruszka <sgruszka@redhat.com>
Acked-by: Michael Chan <mchan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Signed-off-by: Stanislaw Gruszka <sgruszka@redhat.com>
Acked-by: Michael Chan <mchan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Fix SGE resource resource deallocation bug. Forgot to increment the RXQ and
TXQ cursors in the loop ...
Signed-off-by: Casey Leedom <leedom@chelsio.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
A new bit map 'intrCtrl' is introduced in the DriverShared area. The
driver should update VMXNET3_IC_DISABLE_ALL bit before writing IMR.
Signed-off-by: Ronghua Zang <ronghua@vmware.com>
Signed-off-by: Shreyas Bhatewara <sbhatewara@vmware.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Fix LRO feature update.
Signed-off-by: Shreyas Bhatewara <sbhatewara@vmware.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Correct comment stating sizeof(struct tcp_skb_cb) is 36 or 40, since its
44 bytes, since commit 951dbc8ac714b04 ([IPV6]: Move nextheader offset
to the IP6CB).
Signed-off-by: Eric Dumazet <eric.dumazet@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Version update
Signed-off-by: Jon Mason <jon.mason@exar.com>
Signed-off-by: Sreenivasa Honnur <sreenivasa.honnur@exar.com>
Signed-off-by: Ramkrishna Vepa <ramkrishna.vepa@exar.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Update and correct maintainers information
Signed-off-by: Jon Mason <jon.mason@exar.com>
Signed-off-by: Sreenivasa Honnur <sreenivasa.honnur@exar.com>
Signed-off-by: Ramkrishna Vepa <ramkrishna.vepa@exar.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Update copyright information to reflect the Exar purchase of Neterion
Signed-off-by: Jon Mason <jon.mason@exar.com>
Signed-off-by: Sreenivasa Honnur <sreenivasa.honnur@exar.com>
Signed-off-by: Ramkrishna Vepa <ramkrishna.vepa@exar.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
NETIF_F_LLTX and it's usage of local transmit locks are depricated in
favor of using the netdev queue's transmit lock. Remove the local
lock and all references to it, and use the netdev queue transmit lock
in the transmit completion handler.
Signed-off-by: Jon Mason <jon.mason@exar.com>
Signed-off-by: Ramkrishna Vepa <ramkrishna.vepa@exar.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Fix error in multicast flag check, add calls to restore the status of
multicast and promiscuous mode settings after change_mtu, and style
cleanups to shorten the function calls by using a temporary variable.
Signed-off-by: Jon Mason <jon.mason@exar.com>
Signed-off-by: Sreenivasa Honnur <sreenivasa.honnur@exar.com>
Signed-off-by: Ramkrishna Vepa <ramkrishna.vepa@exar.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Remove queue_state references, as they are no longer necessary.
Also, The driver needs to start/stop the queue regardless of which type
of steering is enabled. Remove checks for TX_MULTIQ_STEERING only and
start/stop for all steering types.
Signed-off-by: Jon Mason <jon.mason@exar.com>
Signed-off-by: Sreenivasa Honnur <sreenivasa.honnur@exar.com>
Signed-off-by: Ramkrishna Vepa <ramkrishna.vepa@exar.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
ipv6_skip_exthdr() can return error code that is below zero.
'offset' is unsigned, so it makes no sense.
ipv6_skip_exthdr() returns 'int' so we can painlessly change type of
offset to int.
Signed-off-by: Kulikov Vasiliy <segooon@gmail.com>
Acked-by: Stephen Hemminger <shemminger@vyatta.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
'count' is unsigned. It is initialized to zero, then it can be increased
multiple times, and finally it is used in such a way:
>>>> count--;
|
| /* clear timestamp and dma mappings for remaining portion of packet */
| while (count >= 0) {
| count--;
| ...
^
If count is zero here (so, it was never increased), we would have a very
long loop :)
Signed-off-by: Kulikov Vasiliy <segooon@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
platform_get_irq_byname() can return negative results, it is not seen to
unsigned irq. Make it signed.
Signed-off-by: Kulikov Vasiliy <segooon@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
platform_get_irq_byname() can return negative results, it is not seen to
unsigned irq. Make it signed.
Signed-off-by: Kulikov Vasiliy <segooon@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
There were two methods isdn_gethex() and isdn_getnum() which are custom
implementations of strtoul(). Get rid of them in regard to
strict_strtoul() kernel's function.
Signed-off-by: Andy Shevchenko <andy.shevchenko@gmail.com>
Cc: Hansjoerg Lipp <hjlipp@web.de>
Cc: Tilman Schmidt <tilman@imap.cc>
Cc: Karsten Keil <isdn@linux-pingi.de>
Cc: gigaset307x-common@lists.sourceforge.net
Cc: netdev@vger.kernel.org
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
In this case we safe to use strict_strtoul().
Signed-off-by: Andy Shevchenko <andy.shevchenko@gmail.com>
Cc: Karsten Keil <isdn@linux-pingi.de>
Cc: netdev@vger.kernel.org
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Signed-off-by: Andy Shevchenko <andy.shevchenko@gmail.com>
Cc: Karsten Keil <isdn@linux-pingi.de>
Cc: Tilman Schmidt <tilman@imap.cc>
Cc: netdev@vger.kernel.org
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
This patch converts pci_table entries, where .subvendor=PCI_ANY_ID and
.subdevice=PCI_ANY_ID, .class=0 and .class_mask=0, to use the
PCI_VDEVICE macro, and thus improves readability.
Signed-off-by: Peter Huewe <peterhuewe@gmx.de>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
This patch converts pci_table entries, where .subvendor=PCI_ANY_ID and
.subdevice=PCI_ANY_ID, .class=0 and .class_mask=0, to use the
PCI_VDEVICE macro, and thus improves readability.
Signed-off-by: Peter Huewe <peterhuewe@gmx.de>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
is used)
This patch converts pci_table entries, where .subvendor=PCI_ANY_ID and
.subdevice=PCI_ANY_ID, .class=0 and .class_mask=0, to use the
PCI_VDEVICE macro, and thus improves readability.
Signed-off-by: Peter Huewe <peterhuewe@gmx.de>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
This patch converts pci_table entries, where .subvendor=PCI_ANY_ID and
.subdevice=PCI_ANY_ID, .class=0 and .class_mask=0, to use the
PCI_VDEVICE macro, and thus improves readability.
Signed-off-by: Peter Huewe <peterhuewe@gmx.de>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
is used)
This patch converts pci_table entries, where .subvendor=PCI_ANY_ID and
.subdevice=PCI_ANY_ID, .class=0 and .class_mask=0, to use the
PCI_VDEVICE macro, and thus improves readability.
Signed-off-by: Peter Huewe <peterhuewe@gmx.de>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
This patch converts pci_table entries, where .subvendor=PCI_ANY_ID and
.subdevice=PCI_ANY_ID, .class=0 and .class_mask=0, to use the
PCI_VDEVICE macro, and thus improves readability.
Signed-off-by: Peter Huewe <peterhuewe@gmx.de>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
This patch converts pci_table entries, where .subvendor=PCI_ANY_ID and
.subdevice=PCI_ANY_ID, .class=0 and .class_mask=0, to use the
PCI_VDEVICE macro, and thus improves readability.
Signed-off-by: Peter Huewe <peterhuewe@gmx.de>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
This patch converts pci_table entries, where .subvendor=PCI_ANY_ID and
.subdevice=PCI_ANY_ID, .class=0 and .class_mask=0, to use the
PCI_VDEVICE macro, and thus improves readability.
Signed-off-by: Peter Huewe <peterhuewe@gmx.de>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
