| Age | Commit message (Collapse) | Author |
|---|
|
Add the MCP79 support to hda driver.
The patch base on kernel 2.6.23-rc7
Signed-off-by: Peer Chen <peerchen@gmail.com>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Signed-off-by: Jaroslav Kysela <perex@suse.cz>
|
|
Reading the signature of CS8427 over SPI/I2C fails on some devices
by mysterious reason. In most cases, however, it succeeds at the
sequential read. So, let's give a second chance to check the signature
again.
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Signed-off-by: Jaroslav Kysela <perex@suse.cz>
|
|
Added the missing support for ASUS A7J [0x1043 0x1243]
Signed-off-by: Kailang Yang <kailang@realtek.com.tw>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Signed-off-by: Jaroslav Kysela <perex@suse.cz>
|
|
* Fixed ALC662 init verbs (wrong NIDs)
* Fixed ALC662 auto model issue (wrong DAC index)
Signed-off-by: Kailang Yang <kailang@realtek.com.tw>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Signed-off-by: Jaroslav Kysela <perex@suse.cz>
|
|
The polling loop to check for ACI to go down was more convoluted than it
needed to be. New loop should be more efficient and it is a lot simpler. The
old loop checked for a timeout before checking for ACI down, which could
result in an erroneous timeout. It's only a failure if the timeout expires
_and_ ACI is still high. There is nothing wrong with the timeout expiring
while the task is sleeping if ACI went low.
A polling loop to check for the device to leaving INIT mode is removed. The
device must have already left init for the previous ACI loop to have finished.
Acked-by: Rene Herman <rene.herman@gmail.com>
Signed-off-by: Trent Piepho <xyzzy@speakeasy.org>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Signed-off-by: Jaroslav Kysela <perex@suse.cz>
|
|
Simplest fix.
Acked-by: Rene Herman <rene.herman@gmail.com>
Signed-off-by: Trent Piepho <xyzzy@speakeasy.org>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Signed-off-by: Jaroslav Kysela <perex@suse.cz>
|
|
These patches enable a few YMF743 controls (Tone/3D/IEC958) that won't
be detected with the current version of ALSA.
The second one contains following changes:
- A chip-specific SPDIF support for YMF743 (It doesn't have AC97
standard SPDIF registers seen on YMF753).
- The implementation for 'IEC958 Playback Source' and 'IEC958 Mute'
are identical to the ones for YMF753. But there is no 'IEC958 Output
Pin' for YMF743.
Signed-off-by: Keita Maehara <maehara@debian.org>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Signed-off-by: Jaroslav Kysela <perex@suse.cz>
|
|
These patches enable some YMF743 controls (Tone/3D/IEC958) that won't
be detected with the current version of ALSA.
The first one contains only cosmetic changes to share a few
YMF753-specific symbols with YMF743.
Signed-off-by: Keita Maehara <maehara@debian.org>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Signed-off-by: Jaroslav Kysela <perex@suse.cz>
|
|
Replace schedule_timeout() with schedule_timeout_uninterruptible()
to avoid signals in loop.
Signed-off-by: Rene Herman <rene.herman@gmail.com>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Signed-off-by: Jaroslav Kysela <perex@suse.cz>
|
|
Fix schedule_timeout() use in alsa-kernel. Mostly just
schedule_timeout(1) --> schedule_timeout_uninterruptible(1)
The wavefront_synth one fixes the surrounding loop as well. In ymfpci_main,
delete a superfluous set_current_state() and in soc/soc-dapm.c replace an
_interruptible with _uninterruptible in some debug code; it's not waiting
for signals.
Signed-off-by: Rene Herman <rene.herman>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Signed-off-by: Jaroslav Kysela <perex@suse.cz>
|
|
More laptop BIOS changes the subsystem id for STAC9205 cards if the
microphone is toggled on/off in the settings.
The patch removes the old STAC_9205_M43xx and use STAC_9205_DELL_M43.
Signed-off-by: Matthew Ranostay <mranostay@embeddedalley.com>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Signed-off-by: Jaroslav Kysela <perex@suse.cz>
|
|
Added the description about power-saving mode on AC97 and HD-audio drivers.
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Signed-off-by: Jaroslav Kysela <perex@suse.cz>
|
|
Added CONFIG_SND_AC97_POWER_SAVE_DEFAULT and CONFIG_SND_HDA_POWER_SAVE_DEFAULT
Kconfig options as the default values for power-saving mode of AC97 and
HD-audio drivers, respectively.
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Signed-off-by: Jaroslav Kysela <perex@suse.cz>
|
|
This patch adds support for audio part of the Ensoniq
SoundScape VIVO cards. The MIDI part is not supported.
Signed-off-by: Krzysztof Helt <krzysztof.h1@wp.pl>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Signed-off-by: Jaroslav Kysela <perex@suse.cz>
|
|
The OPTi ISA-PnP chips advertise their OPL4 base at 0x380 (to 0x3f0) through
pnp and put their on-chip OPL3 at +8. The driver assumes the provided
value is the ALBase (OPL3 address) though and checks for an OPL4 at -8,
which means that simply adding 8 to the pnp provides value works to fix
detection of both OPL3 and OPL4.
Problem spotted on 931 and 933 by Krzysztof Helt and confirmed on 924 and
925 (together all OPTi ISA-PnP chips) by me.
Signed-off-by; Rene Herman <rene.herman@gmail.com>
Acked-by: Krzysztof Helt <krzysztof.h1@wp.pl>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Signed-off-by: Jaroslav Kysela <perex@suse.cz>
|
|
Add descriptions for new module options of snd-sscape driver,
wss_port and dma2.
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Signed-off-by: Jaroslav Kysela <perex@suse.cz>
|
|
This patch adds second DMA channel and WSS port settings
to the sscape driver. Also, it adds internal card type setting.
The Ensoniq SoundScape VIVO PnP id is added but not handled
yet.
Signed-off-by: Krzysztof Helt <krzysztof.h1@wp.pl>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Signed-off-by: Jaroslav Kysela <perex@suse.cz>
|
|
This patch adds support for Native Instrument's upcoming
RigKontrol3 sound interface.
Signed-off-by: Daniel Mack <daniel@caiaq.de>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Signed-off-by: Jaroslav Kysela <perex@suse.cz>
|
|
This patch zeroes buffer for the card name and
fixes incorrect jump in the probe function.
Signed-off-by: Krzysztof Helt <krzysztof.h1@wp.pl>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Signed-off-by: Jaroslav Kysela <perex@suse.cz>
|
|
This patch fixes MPU-401 irq values list in documentation.
Signed-off-by: Krzysztof Helt <krzysztof.h1@wp.pl>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Signed-off-by: Jaroslav Kysela <perex@suse.cz>
|
|
Routines for effect processor FX8010: Use list_for_each_entry instead
of list_for_each
Signed-off-by: Matthias Kaehlcke <matthias.kaehlcke@gmail.com>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Signed-off-by: Jaroslav Kysela <perex@suse.cz>
|
|
Intel HD Audio: Use list_for_each_entry(_safe) instead of
list_for_each(_safe)
Signed-off-by: Matthias Kaehlcke <matthias.kaehlcke@gmail.com>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Signed-off-by: Jaroslav Kysela <perex@suse.cz>
|
|
ESS Maestro 1/2/2E Sound Card: Use list_for_each_entry instead of
list_for_each
Signed-off-by: Matthias Kaehlcke <matthias.kaehlcke@gmail.com>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Signed-off-by: Jaroslav Kysela <perex@suse.cz>
|
|
This patch fixes ad1848_lib waiting loops to be the same as in the cs4231_lib.
Acked-by: Rene Herman <rene.herman@gmail.com>
Signed-off-by: Krzysztof Helt <krzysztof.h1@wp.pl>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Signed-off-by: Jaroslav Kysela <perex@suse.cz>
|
|
sound/isa/sc6000.c: In function 'sc6000_dsp_reset':
sound/isa/sc6000.c:270: error: implicit declaration of function 'udelay' sound/isa/sc6000.c: In function 'sc6000_init_mss':
sound/isa/sc6000.c:327: error: implicit declaration of function 'msleep'
{standard input}: Assembler messages:
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Signed-off-by: Jaroslav Kysela <perex@suse.cz>
|
|
This patch adds a barrier() to prevent the compiler from
moving the read outside of the loop. It also fixes a comment.
Signed-off-by: Giuliano Pochini <pochini@shiny.it>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Signed-off-by: Jaroslav Kysela <perex@suse.cz>
|
|
This patch adds support for the Asus M2A-VM HDMI and Abit IP35-PRO
motherboards.
Signed-off-by: Tobin Davis <tdavis@dsl-only.net>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Signed-off-by: Jaroslav Kysela <perex@suse.cz>
|
|
I had a request for a 4 channel mode. This should implement front
and surround outputs, leaving the 3rd plug for mic input.
Signed-off-by: Tobin Davis <tdavis@dsl-only.net>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Signed-off-by: Jaroslav Kysela <perex@suse.cz>
|
|
When playing multichannel data, the rear channels can get distorted if
the last sample of the last played stereo stream was not zero. To avoid
this, add a hack to play a few silence samples after the stream is
stopped.
Signed-off-by: Clemens Ladisch <clemens@ladisch.de>
Signed-off-by: Jaroslav Kysela <perex@suse.cz>
|
|
Remove some unused field from the struct cmipci_pcm, and change the type
of some others to save some space.
Signed-off-by: Clemens Ladisch <clemens@ladisch.de>
Signed-off-by: Jaroslav Kysela <perex@suse.cz>
|
|
When using one of the double sampling rates, use half the sample rate to
look up in the rates[] table, otherwise we stumble over the BUG().
Signed-off-by: Clemens Ladisch <clemens@ladisch.de>
Signed-off-by: Jaroslav Kysela <perex@suse.cz>
|
|
By reorganizing the code that sets the CHB3DxC bits we can not only
simplify this code but also fix the bug where the CHB3D8C bit was not
reset when playing a stereo stream after a 7.1 stream.
Signed-off-by: Clemens Ladisch <clemens@ladisch.de>
Signed-off-by: Jaroslav Kysela <perex@suse.cz>
|
|
Disallow playback of five channels because the hardware does not support
it (or nobody knows how to do it).
Signed-off-by: Clemens Ladisch <clemens@ladisch.de>
Signed-off-by: Jaroslav Kysela <perex@suse.cz>
|
|
Move the code that enables 96 kHz out of the if() that checks for
availability of both DMA channels so that it is enabled even when
another stream is playing on the front channels.
Signed-off-by: Clemens Ladisch <clemens@ladisch.de>
Signed-off-by: Jaroslav Kysela <perex@suse.cz>
|
|
Initialize the registers at 0x90 and 0x91 with some undocumented values.
Signed-off-by: Clemens Ladisch <clemens@ladisch.de>
Signed-off-by: Jaroslav Kysela <perex@suse.cz>
|
|
When the chip is initialized, reset it.
Signed-off-by: Clemens Ladisch <clemens@ladisch.de>
Signed-off-by: Jaroslav Kysela <perex@suse.cz>
|
|
Show a dump of all registers in the 0x00-0x27 and 0x90-0x93 ranges in
the 'cmipci' proc file.
Signed-off-by: Clemens Ladisch <clemens@ladisch.de>
Signed-off-by: Jaroslav Kysela <perex@suse.cz>
|
|
Update comments for many register symbols, add some new register
symbols, and rename a few ones.
Signed-off-by: Clemens Ladisch <clemens@ladisch.de>
Signed-off-by: Jaroslav Kysela <perex@suse.cz>
|
|
Use the proper value for the bit that identifies chip version 37.
Signed-off-by: Clemens Ladisch <clemens@ladisch.de>
Signed-off-by: Jaroslav Kysela <perex@suse.cz>
|
|
Add an 'unknown' board type so that it is possible to differentiate
between unknown and generic boards.
Signed-off-by: Clemens Ladisch <clemens@ladisch.de>
Signed-off-by: Jaroslav Kysela <perex@suse.cz>
|
|
Add a quirk to detect the MIDI port on the M-Audio Ozone Academic.
Signed-off-by: Clemens Ladisch <clemens@ladisch.de>
Signed-off-by: Jaroslav Kysela <perex@suse.cz>
|
|
Signed-off-by: Jaroslav Kysela <perex@suse.cz>
|
|
Remove superfluous volatile prefix in the communication struct definition.
This eventually fixes the compile warnings with the recent gcc, too.
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Signed-off-by: Jaroslav Kysela <perex@suse.cz>
|
|
Added the description of the new sc6000 driver to ALSA-Configuration.txt.
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Signed-off-by: Jaroslav Kysela <perex@suse.cz>
|
|
This is port of the Gallant SC-6000 driver from the OSS aedsp16 driver.
This card was also sold as AudioExcel DSP 16 and Zoltrix AV302 (Audio
Plus True 16).
Signed-off-by: Krzysztof Helt <krzysztof.h1@wp.pl>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Signed-off-by: Jaroslav Kysela <perex@suse.cz>
|
|
When modem is disabled in the BIOS, detection of the number of codecs
always fails after booting if STATESTS is not cleared first.
This patch fixes this problem and also adds an error check in a place
where a read error would lead to a very large number of pointless loops.
Signed-off-by: Danny Tholen <obiwan@mailmij.org>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Signed-off-by: Jaroslav Kysela <perex@suse.cz>
|
|
The non-linked streams couldn't be started properly due to missing
setting of stream->status.
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Signed-off-by: Jaroslav Kysela <perex@suse.cz>
|
|
The volume control for the CS4270 ASoC driver was inverted - raising the
volume level with alsamixer would decrease the actual volume.
This patch also improves the performance of the I2C code (used to change
register settings) by only performing an I2C write if the new value is
different from the value that's in the register cache.
Signed-off-by: Timur Tabi <timur@freescale.com>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Signed-off-by: Jaroslav Kysela <perex@suse.cz>
|
|
This patch replaces long msleeps in waiting loops
with schedule_timeout() calls.
Signed-off-by: Krzysztof Helt <krzysztof.h1 at wp.pl>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Signed-off-by: Jaroslav Kysela <perex@suse.cz>
|
|
The volatile prefix is just useless there. Let's kill them, and then
gcc will be happier, too.
sound/acore/pcm.c:867: warning: passing argument 1 of ‘__constant_c_and_count_memset’ discards qualifiers from pointer target type
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Signed-off-by: Jaroslav Kysela <perex@suse.cz>
|
