| Age | Commit message (Collapse) | Author |
|---|
|
convert_fxsr_to_user() in 2.6.24's i387_32.c did this, and
convert_to_fxsr() also does the inverse, so I assume it's an oversight
that it is no longer being done.
[ mingo@elte.hu:
we encode it this way because there's no space for the 'FPU Last
Instruction Opcode' (->fop) field in the legacy user_i387_ia32_struct
that PTRACE_GETFPREGS/PTRACE_SETFPREGS uses.
it's probably pure legacy - i'd be surprised if any user-space relied on
the FPU Last Opcode in any way. But indeed we used to do it previously
so the most conservative thing is to preserve that piece of information.
]
Signed-off-by: Jan Beulich <jbeulich@novell.com>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
|
|
The Linux kernel currently does not clear the direction flag before
calling a signal handler, whereas the x86/x86-64 ABI requires that.
Linux had this behavior/bug forever, but this becomes a real problem
with gcc version 4.3, which assumes that the direction flag is
correctly cleared at the entry of a function.
This patches changes the setup_frame() functions to clear the
direction before entering the signal handler.
Signed-off-by: Aurelien Jarno <aurelien@aurel32.net>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
Acked-by: H. Peter Anvin <hpa@zytor.com>
|
|
* git://git.kernel.org/pub/scm/linux/kernel/git/lethal/sh-2.6.25:
sh: Fix up the sh64 build.
sh: Fix up SH7710 VoIP-GW build.
sh: Flag PMB support as EXPERIMENTAL.
sh: Update r7780mp defconfig.
fb: hitfb: Balance probe/remove section annotations.
sh: hp6xx: Fix up hp6xx_apm build failure.
fb: pvr2fb: Fix up remaining section mismatch.
sh: Fix up section mismatches.
sh: hp6xx: Correct APM output.
sh: update se7780 defconfig
sh: replace remaining __FUNCTION__ occurrences
sh: export copy-page() to modules
sh_ksyms_32.c update for gcc 4.3
sh/mm/pg-sh7705.c must #include <linux/fs.h>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/cooloney/blackfin-2.6
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/cooloney/blackfin-2.6:
[Blackfin] arch: current_l1_stack_save is a pointer, so use NULL rather than 0
[Blackfin] arch: fix atomic and32/xor32 comments and ENDPROC markings
[Blackfin] arch: fix bug - allow SDH driver to be used as module
[Blackfin] arch: to kill syscalls missing warning by adding new timerfd syscalls
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/aegl/linux-2.6
* 'release' of git://git.kernel.org/pub/scm/linux/kernel/git/aegl/linux-2.6:
[IA64] kprobes arch consolidation build fix
[IA64] update efi region debugging to use MB, GB and TB as well as KB
[IA64] use dev_printk in video quirk
[IA64] remove remaining __FUNCTION__ occurrences
[IA64] remove unnecessary nfs includes from sys_ia32.c
[IA64] remove CONFIG_SMP ifdef in ia64_send_ipi()
[IA64] arch_ptrace() cleanup
[IA64] remove duplicate code from arch_ptrace()
[IA64] convert sys_ptrace to arch_ptrace
[IA64] remove find_thread_for_addr()
[IA64] do not sync RBS when changing PT_AR_BSP or PT_CFM
[IA64] access user RBS directly
|
|
slub_debug=,dentry is correct, not dentry_cache.
Signed-off-by: Itaru Kitayama <i-kitayama@ap.jp.nec.com>
Signed-off-by: Christoph Lameter <clameter@sgi.com>
|
|
NUMA slab allocator cpu migration bugfix
The NUMA slab allocator (specifically, cache_alloc_refill)
is not refreshing its local copies of what cpu and what
numa node it is on, when it drops and reacquires the irq
block that it inherited from its caller. As a result
those values become invalid if an attempt to migrate the
process to another numa node occured while the irq block
had been dropped.
The solution is to make cache_alloc_refill reload these
variables whenever it drops and reacquires the irq block.
The error is very difficult to hit. When it does occur,
one gets the following oops + stack traceback bits in
check_spinlock_acquired:
kernel BUG at mm/slab.c:2417
cache_alloc_refill+0xe6
kmem_cache_alloc+0xd0
...
This patch was developed against 2.6.23, ported to and
compiled-tested only against 2.6.25-rc4.
Signed-off-by: Joe Korty <joe.korty@ccur.com>
Signed-off-by: Christoph Lameter <clameter@sgi.com>
|
|
SLUB should pack even small objects nicely into cachelines if that is what
has been asked for. Use the same algorithm as SLAB for this.
The effect of this patch for a system with a cacheline size of 64
bytes is that the 24 byte sized slab caches will now put exactly
2 objects into a cacheline instead of 3 with some overlap into
the next cacheline. This reduces the object density in a 4k slab
from 170 to 128 objects (same as SLAB).
Signed-off-by: Nick Piggin <npiggin@suse.de>
Signed-off-by: Christoph Lameter <clameter@sgi.com>
|
|
Make them all use angle brackets and the directory name.
Acked-by: Pekka Enberg <penberg@cs.helsinki.fi>
Signed-off-by: Joe Perches <joe@perches.com>
Signed-off-by: Christoph Lameter <clameter@sgi.com>
|
|
The NUMA fallback logic should be passing local_flags to kmem_get_pages() and not simply the
flags passed in.
Reviewed-by: Pekka Enberg <penberg@cs.helsinki.fi>
Signed-off-by: Christoph Lameter <clameter@sgi.com>
|
|
The remote frees are in the freelist of the page and not in the
percpu freelist.
Reviewed-by: Pekka Enberg <penberg@cs.helsinki.fi>
Signed-off-by: Christoph Lameter <clameter@sgi.com>
|
|
ia64 named their handler kprobes_fault_handler while all other
arches used kprobe_fault_handler. Change the function definition
and header declaration.
Signed-off-by: Harvey Harrison <harvey.harrison@gmail.com>
Signed-off-by: Tony Luck <tony.luck@intel.com>
|
|
When EFI_DEBUG is defined to a non-zero value in arch/ia64/kernel/efi.c,
the efi memory regions are displayed. This patch enhances the
display code in a few ways:
1. Use TB, GB and MB as well as KB as units.
Although this introduces rounding errors (KB doesn't as
size is always a multiple of 4Kb), it does make
things a lot more readable.
Also as the range is also shown, it is possible to note the exact size
if it is important. In my experience, the size field is mostly useful
for getting a general idea of the size of a region.
On the rx2620 that I use, there actually is an 8TB region (though not
backed by physical memory, and 8TB really is a lot more readable than
8589934592KB.
2. pad the size field with leading spaces to further improve readability
...
... ( 8MB)
... ( 928MB)
... ( 3MB)
...
vs
...
... (8MB)
... (928MB)
... (3MB)
...
3. Pad the attr field out to 64bits using leading zeros,
to further improve readability.
...
mem05: type= 2, attr=0x0000000000000008, range=[0x0000000004000000-0x000000000481f000) ( 8MB)
mem06: type= 7, attr=0x0000000000000008, range=[0x000000000481f000-0x000000003e876000) ( 928MB)
mem07: type= 5, attr=0x8000000000000008, range=[0x000000003e876000-0x000000003eb8e000) ( 3MB)
mem08: type= 4, attr=0x0000000000000008, range=[0x000000003eb8e000-0x000000003ee7a000) ( 2MB)
...
...
mem05: type= 2, attr=0x8, range=[0x0000000004000000-0x000000000481f000) ( 8MB)
mem06: type= 7, attr=0x8, range=[0x000000000481f000-0x000000003e876000) ( 928MB)
mem07: type= 5, attr=0x8000000000000008, range=[0x000000003e876000-0x000000003eb8e000) ( 3MB)
mem08: type= 4, attr=0x8, range=[0x000000003eb8e000-0x000000003ee7a000) ( 2MB)
...
4. Use %d instead of %u for the index field, as i is a signed int.
N.B: This code is not compiled unless EFI_DEBUG is non 0.
Signed-off-by: Simon Horman <horms@verge.net.au>
Signed-off-by: Tony Luck <tony.luck@intel.com>
|
|
Convert quirk printks to dev_printk().
Signed-off-by: Bjorn Helgaas <bjorn.helgaas@hp.com>
Signed-off-by: Tony Luck <tony.luck@intel.com>
|
|
__FUNCTION__ is gcc-specific, use __func__
Long lines have been kept where they exist, some small spacing changes
have been done.
Signed-off-by: Harvey Harrison <harvey.harrison@gmail.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Tony Luck <tony.luck@intel.com>
|
|
Compilation of 2.6.25-rc2-mm1 on ia64 generates many warnings.
IA64 support 2 ELF format (IA64 binary and IA32 binary),
thus if 2 elf related header included, cause many warning or error.
about 2 week ago, J. Bruce Fields proposed this problem fixed patch.
(http://marc.info/?l=linux-ia64&m=120329313305695&w=2)
Signed-off-by: J. Bruce Fields <bfields@citi.umich.edu>
Signed-off-by: KOSAKI Motohiro <kosaki.motohiro@jp.fujitsu.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Tony Luck <tony.luck@intel.com>
|
|
When !CONFIG_SMP, cpu_physical_id() is ia64_get_lid(), which is
functionally identical to
(ia64_getreg(_IA64_REG_CR_LID) >> 16) & 0xffff
so there's no need for two versions of this code.
Signed-off-by: Bjorn Helgaas <bjorn.helgaas@hp.com>
Signed-off-by: Tony Luck <tony.luck@intel.com>
|
|
* git://git.kernel.org/pub/scm/linux/kernel/git/herbert/crypto-2.6:
[CRYPTO] xcbc: Fix crash with IPsec
[CRYPTO] xts: Use proper alignment
[CRYPTO] digest: Include internal.h for prototypes
[CRYPTO] authenc: Add missing Kconfig dependency on BLKCIPHER
[CRYPTO] skcipher: Move chainiv/seqiv into crypto_blkcipher module
|
|
* 'for-linus' of git://oss.sgi.com:8090/xfs/xfs-2.6:
[XFS] fix inode leak in xfs_iget_core()
[XFS] 977545 977545 977545 977545 977545 977545 xfsaild causing too many
|
|
Commit ed7b1889da256977574663689b598d88950bbd23 removed page.h from
include/asm-generic/Kbuild so that it shouldn't get exported.
However, it was redundantly listed in asm-mn10300/Kbuild and
asm-x86/Kbuild too. Remove those as well, so it really stops being
exported on those architectures. Also remove the redundant listing of
ptrace.h and termios.h from mn10300.
Signed-off-by: David Woodhouse <dwmw2@infradead.org>
Acked-by: David Howells <dhowells@redhat.com>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
|
|
When using aes-xcbc-mac for authentication in IPsec,
the kernel crashes. It seems this algorithm doesn't
account for the space IPsec may make in scatterlist for authtag.
Thus when crypto_xcbc_digest_update2() gets called,
nbytes may be less than sg[i].length.
Since nbytes is an unsigned number, it wraps
at the end of the loop allowing us to go back
into loop and causing crash in memcpy.
I used update function in digest.c to model this fix.
Please let me know if it looks ok.
Signed-off-by: Joy Latten <latten@austin.ibm.com>
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
|
|
The XTS blockmode uses a copy of the IV which is saved on the stack
and may or may not be properly aligned. If it is not, it will break
hardware cipher like the geode or padlock.
This patch encrypts the IV in place so we don't have to worry about
alignment.
Signed-off-by: Sebastian Siewior <sebastian@breakpoint.cc>
Tested-by: Stefan Hellermann <stefan@the2masters.de>
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
|
|
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
|
|
The only board-specific bits that existed here were for setting up the
IRQs, which are now handled by the SH7710 CPU support code instead. As
there's nothing else to do for setup, kill off the board support code
and have the defconfig use the generic machvec instead.
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
|
|
There's still work that needs to be done here, and this should not be
enabled by default on existing boards.
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
|
|
This disables the PMB/32BIT=y by default in r7780mp, as turning this on
presently results in build errors (for an admittedly experimental
feature).
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
|
|
If the radix_tree_preload() fails, we need to destroy the inode we just
read in before trying again. This could leak xfs_vnode structures when
there is memory pressure. Noticed by Christoph Hellwig.
SGI-PV: 977823
SGI-Modid: xfs-linux-melb:xfs-kern:30606a
Signed-off-by: David Chinner <dgc@sgi.com>
Signed-off-by: Lachlan McIlroy <lachlan@sgi.com>
Signed-off-by: Christoph Hellwig <hch@infradead.org>
|
|
wakeups
Idle state is not being detected properly by the xfsaild push code. The
current idle state is detected by an empty list which may never happen
with mostly idle filesystem or one using lazy superblock counters. A
single dirty item in the list that exists beyond the push target can
result repeated looping attempting to push up to the target because it
fails to check if the push target has been acheived or not.
Fix by considering a dirty list with everything past the target as an idle
state and set the timeout appropriately.
SGI-PV: 977545
SGI-Modid: xfs-linux-melb:xfs-kern:30532a
Signed-off-by: David Chinner <dgc@sgi.com>
Signed-off-by: Christoph Hellwig <hch@infradead.org>
Signed-off-by: Lachlan McIlroy <lachlan@sgi.com>
|
|
hitfb presently has probe using __init whilst remove uses __devexit.
As this device can't possibly be hotplugged, switch to __exit and
__exit_p() instead.
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
|
|
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
|
|
Building with CONFIG_DEBUG_SECTION_MISMATCH=y reports:
CC drivers/video/pvr2fb.o
LD drivers/video/built-in.o
WARNING: drivers/video/built-in.o(.text+0xb9b0): Section mismatch in reference from the function pvr2fb_check_var() to the variable .devinit.data:pvr2_fix
The function pvr2fb_check_var() references
the variable __devinitdata pvr2_fix.
This is often because pvr2fb_check_var lacks a __devinitdata
annotation or the annotation of pvr2_fix is wrong.
This is obviously crap as no such reference exists, but it's a bit
closer to reality from older versions which blamed the PCI table. The
real problem was a reference to pvr2_var.vmode from pvr2fb_check_var(),
as pvr2_var is flagged as __devinitdata (pvr2_fix is also, so at least
that part is right).
pvr2_var.vmode is just a fancy way of saying FB_VMODE_NONINTERLACED, so
we just reference that explicitly instead.
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
|
|
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
|
|
This patch fixes the old non-verbose hp6xx apm code and enables some
very basic apm output. We now get percentage (battery) output
and basic time estimate.
Signed-off-by: Kristoffer Ericson <kristoffer.ericson@gmail.com>
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
|
|
This patch updates se7780_defconfig
Signed-off-by: Yusuke Goda <goda.yusuke@renesas.com>
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
|
|
__FUNCTION__ is gcc-specific, use __func__
Signed-off-by: Harvey Harrison <harvey.harrison@gmail.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
|
|
ERROR: "copy_page" [fs/unionfs/unionfs.ko] undefined!
like all the other architectures.
Cc: Erez Zadok <ezk@cs.sunysb.edu>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
|
|
This patch fixes the following build error with landisk_defconfig when
using gcc 4.3:
<-- snip -->
...
MODPOST 50 modules
ERROR: "__udivsi3_i4i" [net/sunrpc/sunrpc.ko] undefined!
ERROR: "__udivsi3_i4i" [net/appletalk/appletalk.ko] undefined!
ERROR: "__udivsi3_i4i" [fs/ufs/ufs.ko] undefined!
ERROR: "__udivsi3_i4i" [fs/ntfs/ntfs.ko] undefined!
ERROR: "__sdivsi3_i4i" [fs/ntfs/ntfs.ko] undefined!
ERROR: "__udivsi3_i4i" [fs/nfsd/nfsd.ko] undefined!
ERROR: "__sdivsi3_i4i" [fs/nfsd/nfsd.ko] undefined!
ERROR: "__udivsi3_i4i" [fs/nfs/nfs.ko] undefined!
ERROR: "__udivsi3_i4i" [fs/lockd/lockd.ko] undefined!
ERROR: "__udivsi3_i4i" [drivers/usb/storage/usb-storage.ko] undefined!
ERROR: "__sdivsi3_i4i" [drivers/usb/serial/pl2303.ko] undefined!
ERROR: "__udivsi3_i4i" [drivers/usb/serial/pl2303.ko] undefined!
ERROR: "__sdivsi3_i4i" [drivers/usb/serial/ftdi_sio.ko] undefined!
ERROR: "__udivsi3_i4i" [drivers/usb/misc/sisusbvga/sisusbvga.ko] undefined!
ERROR: "__sdivsi3_i4i" [drivers/usb/misc/sisusbvga/sisusbvga.ko] undefined!
ERROR: "__udivsi3_i4i" [drivers/media/video/v4l1-compat.ko] undefined!
ERROR: "__sdivsi3_i4i" [drivers/media/video/v4l1-compat.ko] undefined!
ERROR: "__sdivsi3_i4i" [drivers/media/video/usbvideo/vicam.ko] undefined!
ERROR: "__udivsi3_i4i" [drivers/media/video/usbvideo/usbvideo.ko] undefined!
ERROR: "__sdivsi3_i4i" [drivers/media/video/usbvideo/usbvideo.ko] undefined!
ERROR: "__udivsi3_i4i" [drivers/media/video/sn9c102/sn9c102.ko] undefined!
ERROR: "__sdivsi3_i4i" [drivers/media/video/sn9c102/sn9c102.ko] undefined!
ERROR: "__sdivsi3_i4i" [drivers/media/video/se401.ko] undefined!
ERROR: "__sdivsi3_i4i" [drivers/media/video/pwc/pwc.ko] undefined!
ERROR: "__udivsi3_i4i" [drivers/md/raid0.ko] undefined!
ERROR: "__udivsi3_i4i" [drivers/md/md-mod.ko] undefined!
ERROR: "__sdivsi3_i4i" [drivers/md/md-mod.ko] undefined!
ERROR: "__udivsi3_i4i" [drivers/md/linear.ko] undefined!
ERROR: "__sdivsi3_i4i" [drivers/hid/usbhid/usbhid.ko] undefined!
make[2]: *** [__modpost] Error 1
<-- snip -->
Signed-off-by: Adrian Bunk <adrian.bunk@movial.fi>
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
|
|
This patch fixes the following compile error:
<-- snip -->
...
CC arch/sh/mm/pg-sh7705.o
/home/bunk/linux/kernel-2.6/git/linux-2.6/arch/sh/mm/pg-sh7705.c: In function 'ptep_get_and_clear':
/home/bunk/linux/kernel-2.6/git/linux-2.6/arch/sh/mm/pg-sh7705.c:130: error: implicit declaration of function 'mapping_writably_mapped'
make[2]: *** [arch/sh/mm/pg-sh7705.o] Error 1
<-- snip -->
Signed-off-by: Adrian Bunk <adrian.bunk@movial.fi>
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
|
|
Signed-off-by: Mike Frysinger <vapier.adi@gmail.com>
Signed-off-by: Bryan Wu <cooloney@kernel.org>
|
|
* 'for-linus' of git://git.infradead.org/~dedekind/ubi-2.6:
UBI: mtd/ubi/vtbl.c: fix memory leak
UBI: fix sparse errors in ubi.h
UBI: fix error message
UBI: silence warning
|
|
On 32bits boxes, boundary_size becomes zero due to a overflow and we
hit BUG_ON in iommu_is_span_boundary.
Signed-off-by: FUJITA Tomonori <fujita.tomonori@lab.ntt.co.jp>
Cc: Kyle McMartin <kyle@parisc-linux.org>
Cc: Matthew Wilcox <matthew@wil.cx>
Acked-by: Grant Grundler <grundler@parisc-linux.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
|
|
mm migration is no longer done in cpuset_update_task_memory_state() so it
can no longer take current->mm->mmap_sem, so fix the obsolete comment.
[ This changed in commit 04c19fa6f16047abff2288ddbc1f0798ede5a849
("cpuset: migrate all tasks in cpuset at once") when the mm migration
was moved from cpuset_update_task_memory_state() to update_nodemask() ]
Signed-off-by: David Rientjes <rientjes@google.com>
Cc: Paul Jackson <pj@sgi.com>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
|
|
* git://git.kernel.org/pub/scm/linux/kernel/git/jejb/scsi-rc-fixes-2.6: (27 commits)
[SCSI] mpt fusion: don't oops if NumPhys==0
[SCSI] iscsi class: regression - fix races with state manipulation and blocking/unblocking
[SCSI] qla4xxx: regression - add start scan callout
[SCSI] qla4xxx: fix host reset dpc race
[SCSI] tgt: fix build errors when dprintk is defined
[SCSI] tgt: set the data length properly
[SCSI] tgt: stop zero'ing scsi_cmnd
[SCSI] ibmvstgt: set up scsi_host properly before __scsi_alloc_queue
[SCSI] docbook: fix fusion source files
[SCSI] docbook: fix scsi source file
[SCSI] qla2xxx: Update version number to 8.02.00-k9.
[SCSI] qla2xxx: Correct usage of inconsistent timeout values while issuing ELS commands.
[SCSI] qla2xxx: Correct discrepancies during OVERRUN handling on FWI2-capable cards.
[SCSI] qla2xxx: Correct needless clean-up resets during shutdown.
[SCSI] arcmsr: update version and changelog
[SCSI] ps3rom: disable clustering
[SCSI] ps3rom: fix wrong resid calculation bug
[SCSI] mvsas: fix phy sas address
[SCSI] gdth: fix to internal commands execution
[SCSI] gdth: bugfix for the at-exit problems
...
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/jmorris/selinux-2.6
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/jmorris/selinux-2.6:
NFS: use new LSM interfaces to explicitly set mount options
LSM/SELinux: Interfaces to allow FS to control mount options
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/davej/cpufreq
* 'fixes-25' of git://git.kernel.org/pub/scm/linux/kernel/git/davej/cpufreq:
[CPUFREQ] fix section mismatch warnings
[CPUFREQ] Remove debugging message from e_powersaver
[CPUFREQ] Fix missing cpufreq_cpu_put() call in ->store
[CPUFREQ] Fix missing cpufreq_cpu_put() call in ->show
|
|
* 'for-linus' of git://git390.osdl.marist.edu/pub/scm/linux-2.6:
[S390] incorrect reipl nss name.
[S390] Load disabled wait psw if reipl fails.
[S390] Fix IPL from NSS.
[S390] zcrypt: fix ap_device_list handling
[S390] sclp_vt220: speed up console output for interactive work
[S390] dasd: fix reference counting in display method for proc/dasd/devices
[S390] dasd: let dasd erp matching recognize alias recovery
[S390] Get rid of memcpy gcc warning workaround.
[S390] idle: Fix machine check handling in idle loop.
[S390] Update default configuration.
|
|
Remove duplicate code, clean up goto's and indentation.
Signed-off-by: Petr Tesarik <ptesarik@suse.cz>
Signed-off-by: Tony Luck <tony.luck@intel.com>
|
|
Remove all code which does exactly the same thing as ptrace_request().
Signed-off-by: Petr Tesarik <ptesarik@suse.cz>
Signed-off-by: Tony Luck <tony.luck@intel.com>
|
|
Convert sys_ptrace() to arch_ptrace().
Signed-off-by: Petr Tesarik <ptesarik@suse.cz>
Signed-off-by: Tony Luck <tony.luck@intel.com>
|
|
find_thread_for_addr() is no longer needed. It was only used to find
the correct kernel RBS for a given memory address, but since the kernel
RBS is not needed any longer, this function can go away.
Signed-off-by: Petr Tesarik <ptesarik@suse.cz>
Signed-off-by: Tony Luck <tony.luck@intel.com>
|
